3M X80, X64w, X95, X90K, X75 User Manual

...
0 (0)
3M
Digital Projector
Control Application Guide Version 4.12
For Models: X21i / X26i / X30n / X31/ X31i / X35n / X36 / X36i / WX36 / WX36i / X46 / X46i / X56 / X62w / X64w / X70 / X75 / X80 / X90 / X90K / X90W / X95 / X95i
Revision Date Page(s) Changed Description of Change
4/2009 All pages First edition, models X70, X75, X80, X90, X95, X95i 4/2010 All pages Add models X62w, X64w, X30n, X35n 6/2010 All pages Add models X31, X36, X46 7/2010 All pages Add model WX36
12/2011 All pages Add model X56
3/2012 All pages Add model X21i, X26i 8/2012 All pages Add model X31i, X36i, X46i, WX36i
Intended Use
The 3M™ Digital Projectors are designed, built, and tested for use indoors, using 3M lamps, 3M ceiling mount hardware, and common line voltages (100V to 240V AC, 50/60 Hz).The use of other replacement lamps, outdoor operation, or different voltages has not been tested and could damage the projector, peripheral equipment and/or create a potentially unsafe operating condition.
3M Digital Projectors are designed to operate in a normal office environment.
100V - 240V AC, 50/60 Hz
16° to 29° C (60° to 85° F)
10-80% RH (without condensation)
0-1828m (0-6000 feet) above sea level
The ambient operating environment should be free of airborne smoke, grease, oil and other contaminates that can effect the operation or performance of the projector.
The 3M logo and 3M are trademarks of the 3M Company. Other trademarks used herein are the properties of their respective owners.
Important Notice
All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M.
Warranty and Limited Remedy
3M warrants that when the 3M Product is used according to 3M’s Intended Use Statement (www.3M.com/meetings), it will perform satisfactorily for the warranted durability period as stated in the applicable 3M Product Manual in effect at the time of purchase. The warranties stated in the applicable 3M Product Manuals are exclusive and are made in place of any and all express or implied warranties or conditions, including any implied warranty of merchantability or fitness for a particular purpose, or any industry practice or custom or trade usage. Failure to follow the instructions contained in the appropriate 3M Product Manual or to use the 3M Product in accordance with 3M’s Intended Use Statement will void all warranties and limited remedies.
EXCEPT AS SPECIFICALLY STATED IN THE APPLICABLE 3M PRODUCT MANUAL, 3M SHALL NOT BE LIABLE FOR ANY INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFITS, REVENUE OR BUSINESS) RESULTING FROM, OR IN ANY WAY RELATED TO PERFORMANCE, USE OR INABILITY TO USE ANY OF THE 3M PRODUCT.
This limitation applies regardless of the legal theory upon which damages are sought. If 3M Product is defective within the applicable warranty period, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M Product or to refund the purchase price of the 3M Product. All replaced parts or products become property of 3M. If the 3M Product is repaired, 3M will repair the defective part(s) with a new or used part(s). If the 3M Product is replaced, 3M will replace the product with the same or equivalent model and with a new or refurbished product. In the case of an approved warranty claim, the replacement 3M Product will carry only the remaining term of the original 3M Product’s warranty period as stated in the applicable 3M Product Manual.
For warranty service, you must provide proof of the date of the original purchase, otherwise the manufacturing code date will be used to establish the start date of the warranty. 3M Product Manuals include durability statements and may include limitations specific to the product(s) being used or its intended applications, which take precedence over any statement made here. Warranty terms, limitations and exclusions may differ outside the United States of America.
3M Mobile Interactive Solutions Division 6801 River Place Boulevard Tel: 1-800-328-1371 Austin, Texas 78726-9000 © 3M 2012. All Rights Reserved.
www.3m.com/meetings
78-6971-1513-3 [Aug. 2012]
Contents
© 3M 2012. All Rights Reserved.
1. INTRODUCTION .......................................................................................................................................... 3
1.1 O
1.2 S
UTLINE ................................................................................................................................................. 3
YSTEM.................................................................................................................................................. 3
2. INSTALLATION ........................................................................................................................................... 4
2.1 S
2.2 P
YSTEM REQUIREMENTS ......................................................................................................................... 4
ROJECTOR CONTROL INSTALLATION ...................................................................................................... 5
3. OPERATING INSTRUCTIONS .................................................................................................................... 7
3.1 C
3.2 S
3.3 M
3.4 E
3.5 A
3.6 C
3.7 B
3.8 A
3.9 I
REATE LOGIN ACCOUNTS ...................................................................................................................... 7
TART APPLICATION ............................................................................................................................... 9
AIN WINDOW ........................................................................................................................................ 9
XIT APPLICATION ................................................................................................................................ 10
PPLICATION MINIMIZATION .................................................................................................................. 11
ONFIGURE PROJECTOR SETTINGS ....................................................................................................... 11
UTTONS ............................................................................................................................................. 14
DVANCED CONTROL ........................................................................................................................... 15
MAGE SEND TO PROJECTOR ................................................................................................................. 61
3.10 MY
3.11 S
IMAGE (E-SHOT) .......................................................................................................................... 61
OFTWARE VERSION ............................................................................................................................. 61
・Microsoft and Windows is the registered trademark of Microsoft Corporation in the US and other countries. ・Pentium is the registered trademark of Intel Corporation in the US and other countries. ・All other trademarks are the property of their respected owners.
Warning
・This software is free. The manufacturer has no responsibility for any errors that may occur while using this software. ・This software, or any product used with this software may not be used for any act which obstructs the Maintenance
of the International Peace and Safety.
2
1. Introduction
© 3M 2012. All Rights Reserved.
1.1 Outline
The Projector Control Application, PJCtrl is software that allows you to control the projectors on the network or connected via RS232C cable. With this application, the Computer can control projectors on the network remotely.
1.2 System
The following diagram shows a typical network diagram for the Projector Tool.
RS-232C
LAN
HUB
LANLAN
LANLAN
Ethernet
/ RS-232C
Converter
RS-232C
Use a UTP cable category 5 or higher for a Local Area Network cable.
Use a cross type cable when using a serial cable.
The Projector Control Application can control up to 5 of the same model projectors.
3
2. Installation
© 3M 2012. All Rights Reserved.
2.1 System Requirements
The minimum System requirements for the Projector Control Application are shown below.
(1) Operating System
Windows 2000 Professional Windows XP Home Edition / Professional Windows Vista Home Basic / Home Premium / Business / Ultimate / Enterprise Windows 7 Starter / Home Basic / Home Premium / Professional / Ultimate / Enterprise
(2) CPU
Pentium3 500MHz or higher
(3) Memory
128MB or higher
(4) Hard disk space
Minimum 20MB free space for installation
(5) Serial port
This port is required to control projectors by RS-232C
(6) LAN port
This port is required to control projectors through a network
4
2.2 Projector Control Installation
© 3M 2012. All Rights Reserved.
Please follow next steps to install the software into your computer.
(1) Double click the file “InstForPJCtrl.exe”.
(2) Select the language (English, Japanese or Chinese
[Simplified]) during the installation process. And then click [OK].
(3) Click [Next].
(4) Read “License Agreement” and select “I accept the terms of
the license agreement” and click [Next] if you agree the license agreement. Otherwise, click [Cancel] and stop the installation.
(5) Confirm the program folder, and then click [Next].
5
© 3M 2012. All Rights Reserved.
(6) Confirm the install folder and program folder again, and then
click [Next].
(7) Click [Finish] to complete the Projector Control Application
setup wizard.
6
3. Operating Instructions
© 3M 2012. All Rights Reserved.
3.1 Create login accounts
The Projector Control Application requires a login name and password to launch the software. The Projector User Administration Tool helps you to create new user accounts.
3.1.1 How to launch
Double Click “PJUsrEdit.exe” that is located on same folder that you installed Projector Control Application. It automatically launches the Projector User Administration Tool, if no user accounts are created yet. Also Projector Control Application has a short cut [File] [User Configuration] to launch Projector User Administration Tool.
3.1.2 How to exit
Select [File] [Exit] from the menu or click [x] bottom of the top right corner. If the changes are made, you will be required to confirm the changes.
3.1.3 Main Window
Menu
(1) Menu
Menu Sub Menu Description
File Save Save user data
Edit Add New User Create new user
User List
Exit Exit
Change User Edit user account Delete User Delete user account
(2) User List
The status in the User List is described below.
Row name Description
User Name Username (ID) Description Comment Man “” shows that the user can access to the PJMan (Projector Management Tool) Ctrl “” shows that the user can access to the PJCtrl (Projector Control Tool) Img “” shows that the user can access to the PJImg (Projector Image Tool) FTP “” shows that the user can access to the PJTransfer (Projector File Transfer Tool).
7
3.1.4 Creating new user account
© 3M 2012. All Rights Reserved.
Select [Edit] [Add New User] or right clicks on the user list and select [Add New User]. The following dialog window appears.
User Name --- Define user name, up to 20 characters Description --- Add comments, up to 50 characters User Rights --- Define accessibility. It defines the
accessibility for the application software by each user account. The user can use
allocation only marked application software. Select All --- Select all application software. UnSel All --- Unselect all application software.
Press [OK] button after entering user name. The [Change Password] dialog appears. Enter new password and confirm entered password. The password is up to 20 characters and case sensitive.
3.1.5 Edit user account
Double click a username on the user list or select [Edit] [Change User] after choosing user to open edit dialog. You can edit username, description and accessibility (user rights). Click the button to change password. Enter old and new password, and re-enter new password to confirm.
3.1.6 Delete user account
Select [Edit] [Delete User] or right click on the user list and select [Delete User]. The confirmation window will popup.
3.1.7 Save user account
Select [File]  [Save]. The date is stored in the file, “C:\Program Files\Common Files\Projector Tools\config \UserList”.
8
3.2 Start Application
[
© 3M 2012. All Rights Reserved.
Select Windows [Start] [Program] [Projector Tools] [Projector Control Application]. The login window is appeared. Enter the username and password that is created by “Projector User Administration Tool”. After logged in, a “Configuration” window is appeared. Please refer the section 3.6 Configure Projector Settings on page 9. Once the configuration is done, click [OK].
3.3 Main Window
Click the icon to perform each function. The functions are shown below.
Note: Some icons may not show up depending on the model you choose. For example, [Image Send] icon is only for the models CL33X, CL35X, CL67N, CL69N, CL86X, PL90X, PL92X, PL96X, WX36, WX36i, X21i, X26i, X30N, X31, X31i, X35N, X35NK, X36, X36i, X46, X46i, X56, X90 and X90K.
[About] icon [Image Send] icon [Advanced] icon [Freeze Off] icon [Freeze On] icon [Mute] icon [Volume] icon [Blank Off] icon [Blank On] icon [Input Source] icon [Power Off] icon [Power On] icon
Configuration] icon
9
3.4 Exit Application
© 3M 2012. All Rights Reserved.
Right click the PJCtrl icon on the task tray at the right-bottom corner and select [exit]. And click [Yes] on the confirmation window. Also you can click the [x] icon on the right top corner of main window to exit application.
10
3.5 Application Minimization
© 3M 2012. All Rights Reserved.
You can hide the main window into the task tray to click the minimization icon on the window. Right click the PJCtrl icon on the task tray and select [Show] to restore window.
3.6 Configure Projector Settings
You need to setup the projector settings such as connection type and projector model. Click the [Configuration] icon to configure settings.
(1) Projector Model
Select a projector model that you want to control from the drop down list. The icons on the main window and Advanced Control items are vary due to the model differences. The discovery feature is available on CL33X, CL35X, CL67N, CL69N, CL72X, CL73W, CL73X, CL86X, NE7, PL90X, PL92X, PL93X, PL95X, PL96X, WX36, WX36i, X21i, X26i, X30N, X31, X31i, X35N, X35NK, X36, X36i, X46, X46i, X56, X62w, X64w, X90, X90K, X90w, X95, X95K, X95i and X95iK.
The discovery feature will find all projectors on the network if the discovery feature is supported. Once the discovery is done, the discovery result is stored in the software and you can look up this result from “Configuration” window.
[NOTE]
Windows Security Alert will be shown on your display when the discovery function activates, if Windows Firewall is “On” on Windows XP SP2 or later. Please choose “Unblock” to add the software onto the exception list. Also other firewall security software may block the discovery function. In that case, please add the software to the safe list or disable firewall software when you use discovery function.
11
(2) Connection Setting
© 3M 2012. All Rights Reserved.
RS-232C --- Check the radio button and choose
COM port number for serial connection.
NETWORK --- Check the radio button for network
connection. Please enter the IP address of projector and port number. You can choose the projector from the discovered list if the discovery function is already run. The default port number of PL75X, PL80X, X70, X75, X75C, X75K, X80, X80C and X80K is 23. The default of CL33X, CL35X, CL67N, CL69N, CL72X, CL73W, CL73X, CL86X, NE7, PL93X, PL96X, WX36, WX36i, X21i, X26i, X30N, X31, X31i, X35N, X35NK, X36, X36i, X46, X46i, X56, X62w, X64w, X90, X90K, X90w, X95, X95K, X95i and X95iK is 23 or
9715. Authentication and Password is available for CL33X, CL35X, CL67N, CL69N, CL72X, CL73W, CL73X, CL86X, NE7, PL90X, PL93X, PL95X, PL92X, PL96X, WX36, WX36i, X21i, X26i, X30N, X31, X31i, X35N, X35NK, X36, X36i, X46, X46i, X56, X62w, X64w, X90, X90K, X90w, X95, X95K, X95i and X95iK.
Projector List --- The list shows the projectors that you register.
[Insert] : Insert new projector into the projector list. [Update] : Update selected projector setting and save changes. [Delete] : Delete selected projector from the projector list. When you manage multiple projectors at the same time, you need to pick one
projector and select a checkbox in order to be a delegate for displaying CH selection and volume level.
Please rarify IP settings to make sure the PJCtrl is able to communicate with the projector by ping command.
(3) Configure Buttons
Click the Show Buttons TAB to configure which bottoms you want to use. Check the checkbox that you want to show as the button. The configuration window can be displayed if you make a right click on the task tray icon.
Icon Size:
Also you can choose icon size from 24, 36 or 48 dots.
Always on top:
“Always on top” option allows that the PJCtrl application always show up foreground.
12
(4) Option
© 3M 2012. All Rights Reserved.
Skip user check:
Check “skip user check” option if you don’t need the user login process at application launch. If you need to check user account at each time, uncheck this option.
Skip configuration dialog:
Check “skip configuration dialog” option if you don’t need to show the configuration window at application launch.
User Configuration:
Launch Projector User Administration Tool.
Edit CH Label:
Display Edit CH Label window.
Configure CH label text that shows underneath each CH icon. The text length is depending on the icon size as shown below.
Icon size 24x24: up to 4 characters Icon size 36x36: up to 6 characters Icon size 48x48: up to 8 characters
This is an example how CH label is looks like.
Update Interval:
Set the interval period to update CH status from the projector.
13
3.7 Buttons
© 3M 2012. All Rights Reserved.
Power ON:
Power the projector on.
Power OFF:
Power the projector off.
Input Source:
Switch the input source (CH). The icon of current input channel is shown as “selected” icon (hollow). When you manage multiple projectors, the status of delegated projector is shown.
Blank ON:
Blank the screen.
Blank OFF:
Un-blank the screen.
Volume:
Volume up and down. The control bar appears when you click the icon. When you manage multiple projectors, the delegated projector’s value is displayed. Please note that the value may not the same among multiple projectors.
Mute:
Sound mute. Toggled.
Freeze ON:
Freeze image.
Freeze OFF:
Unfreeze image.
14
3.8 Advanced Control
© 3M 2012. All Rights Reserved.
You can access the advanced control functions through Advanced Control Menu. Click the “ADV” icon to open the advanced control window. Choose the target projector to control.
Advanced control items are depending on the projector model.
PL80X / X70 / X80 / X80C / X80K
[STATUS] Tab
Function General Description Power Displays the current power status.
Input Source Displays the current input source.
Error Status Displays the current error status.
Blank On /Off Displays the current blank on/off status.
Mute Displays the current mute status.
Freeze Displays the current freeze status.
Lamp Time Displays the usage time for the current lamp. Filter Time Displays the usage time for the current filter. Reset Initialize the selected function.
[MAIN] Tab
Function General Description Bright Adjusts the brightness.
Contrast Adjusts the contrast.
Aspect Switches the mode for aspect ratio.
Whisper Turn off/on the whisper mode.
Mirror Switches the mode for mirror status.
Language Switches the menu language.
Reset Initialize the selected function.
Off / On / Cool down
M1-D / RGB / BNC / Video / S-Video / Component
Normal / Cover Error / Fan Error / Lamp Error / Temp Error / Air Flow Error / Lamp Time Error / Cold Error / Filter Error / Other Error
Off / On
Off / On
Normal / Freeze
Lamp Time / Filter Time
[Execute]: After the confirmation message, the selected function will be initialized.
[-]: Decrease the brightness value. [+]: Increase the brightness value.
[-]: Decrease the contrast value. [+]: Increase the contrast value.
4:3 / 16:9 / Small / Normal
Normal / Whisper
Normal / H:Invert / V:Invert / H&V:Invert
English / French / German / Spanish / Italian / Norwegian / Dutch / Portuguese / Japanese / Simplified Chinese / Korean / Swedish / Russian / Finnish / Polish
Bright / Contrast
[Execute]: After the confirmation message, the selected function will be initialized.
15
[PICTURE-1] Tab
© 3M 2012. All Rights Reserved.
Function General Description Gamma Switches the gamma mode.
Normal / Cinema / Dynamic / Custom
Custom Gamma Adjusts the gamma data.
[-]: Decrease the gamma value. [+]: Increase the gamma value.
Color Temp Switches the color temperature mode.
Low / Middle / High / User
Custom User R Adjusts the red color level for the user mode of red color temperature.
100 / 90 / 80 / 70 / 60 / 50
Custom User G Adjusts the green color level for the user mode of green color temperature.
100 / 90 / 80 / 70 / 60 / 50
Custom User B Adjusts the blue color level for the user mode of blue color temperature.
100 / 90 / 80 / 70 / 60 / 50
Color Bal R Adjusts the red color balance.
[-]: Decrease the red color balance value. [+]: Increase the red color balance value.
Color Bal G Adjusts the green color balance.
[-]: Decrease the green color balance value. [+]: Increase the green color balance value.
Color Bal B Adjusts the blue color balance (blue).
[-]: Decrease the blue color balance value. [+]: Increase the blue color balance value.
Sharpness Adjusts the sharpness.
[-]: Decrease the sharpness value. [+]: Increase the sharpness value
Color Adjusts the strength of whole color.
[-]: Decrease the color value. [+]: Increase the color value
Tint Adjusts the tint.
[-]: Decrease the tint value. [+]: Increase the tint value.
My Memory Loads the data from the memory.
Load1 / Load2 / Load3 / Load4
Saves the current adjustment data into the memory.
Save1 / Save2 / Save3 / Save4
[Execute]: Performs each function.
Reset Initialize the selected function.
Color Bal R / Color Bal G / Color Bal B / Sharpness / Color / Tint
[Execute]: After the confirmation message, the selected function will be initialized.
[PICTURE-2] Tab
Function General Description Position Adjust the display position.
[
]: Increase the vertical position value.
[
]: Decrease the vertical position value.
[
]: Increase the horizontal position value.
[
]: Decrease the horizontal position value.
H Phase Adjust the horizontal phase to eliminate flicker.
[-]: Decrease the horizontal phase value. [+]: Increase the horizontal phase value.
H Size Adjust the horizontal size.
[-]: Decrease the horizontal size value. [+]: Increase the horizontal size value.
Over Scan Adjust the over-scan ratio.
[-]: Decrease the over-scan value. [+]: Increase the over-scan value.
Reset Initialize the selected function.
V Position / H Position / H Size / Over Scan
[Execute]: After the confirmation message, the selected function will be initialized.
16
[INPUT] Tab
© 3M 2012. All Rights Reserved.
Function General Description Color Space Switches the mode for color space.
Auto / RGB / SMPTE240 / REC709 / REC601
Component Switches the function of the COMPONENT port.
Component / Scart RGB
Video Format Switches the mode for video format.
Auto / NTSC / PAL / SECAM / NTSC4.43 / M-PAL / N-PAL
3D-YCS Turns off/on the 3D-YCS.
Off / On
Video NR Switches the noise reduction mode.
Low / Middle / High
S2-Aspect Turns off/on the S2-aspect function
Off / On
P.IN P. Input Switches the signal input port for the child window.
Video / S-Video
P.IN P. Position Switches the display position of the child window.
Upper Left / Upper Right / Bottom Left / Bottom Right
P.IN P. Audio Switches the audio source of the child window.
RGB / Video
P.IN P. Size Switches the display size of the child window.
Off / Large / Small
Power Up Input Switches the signal input port to display just when the projector is turned on.
Last Input / M1-D / RGB / BNC / Component / S-Video / Video
[AUTO] Tab
Function General Description Adjust [Execute]: Performs the automatic adjustment feature.
Power Off Adjusts the time to count down to automatically turn the projector off.
[-]: Decrease auto power off time. [+]: Increase auto power off time.
Power On Turns off/on the auto power on function.
Off / On
Search Turns off/on the automatic signal search function.
Off / On
[SCREEN] Tab
Function General Description Blank Switches the mode for the blank screen.
Blue / White / Black / MyScreen / Original
Start Up Switches the mode for the start-up screen.
Original / Off / MyScreen
MyScreen Size Switches the size of the MyScreen.
Full / x1
MyScreen Lock Turn off/on the MyScreen lock function.
Off / On
Menu Position Adjusts the menu position.
[
]: Increase the vertical menu position value.
[
]: Decrease the vertical menu position value.
[
]: Decrease the horizontal menu position value.
[
]: Increase the horizontal menu position value.
Message Turns off/on the message function.
Off / On
Reset Initialize the selected function.
Menu Position V / Menu Position H
[Execute]: After the confirmation message, the selected function will be initialized.
17
[OPTION] Tab
© 3M 2012. All Rights Reserved.
Function General Description Volume Adjusts the volume.
[-]: Decrease the volume value. [+]: Increase the volume value.
Speaker Turns off/on the built-in speaker.
Off / On
IR Remote Turns off/on the remote sensor.
Front (Off / On) Rear (Off / On) Top (Off / On)
IR Remote ID Switches the number as an ID number for remote control.
All / 1 / 2 / 3
Auto Adjust Switches the auto adjustment enable function.
Disable / Enable
Lens Type Switches the lens type currently used.
Auto / 1 / 2 / 3 / 4 / 5
Lens Lock Turns off/on the lens lock function.
Off / On
[OTHER] Tab
Function General Description Power Turns off/on the power.
Input Source Switchs the input source.
Blank On / Off Turns off/on the blank.
Mute Turns off/on the mute.
Freeze Turn off/on the freeze.
Magnify Adjusts the magnify setting.
Keystone V Adjusts the vertical keystone distortion.
Keystone H Adjusts the horizontal keystone distortion.
Reset Initialize the selected function.
Off / On
M1-D / RGB / BNC / Video / S-Video / Component
Off / On
Off / On
Normal / Freeze
[-]: Decrease the magnify value. [+]: Increase the magnify value.
[-]: Decrease the vertical keystone value. [+]: Increase the vertical keystone value.
[-]: Decrease the horizontal keystone value. [+]: Increase the horizontal keystone value.
Keystone V / Keystone H
[Execute]: After the confirmation message, the selected function will be initialized.
18
PL75X / X75 / X75C / X75K
© 3M 2012. All Rights Reserved.
[STATUS] Tab
Function General Description Power Displays the current power status.
Input Source Displays the current input source.
Error Status Displays the current error status.
Blank On / Off Displays the current blank on/off status.
Mute Displays the current mute status.
Freeze Displays the current freeze status.
Lamp Time Displays the usage time for the current lamp. Filter Time Displays the usage time for the current filter. Reset Initialize the selected function.
Off / On / Cool down
DVI / RGB1 / RGB2 / Video / S-Video / Component
Normal / Cover Error / Fan Error / Lamp Error / Temp Error / Air Flow Error / Lamp Time Error / Cold Error / Filter Error / Other Error
Off / On
Off / On
Normal / Freeze
Lamp Time / Filter Time
[Execute]: After the confirmation message, the selected function will be initialized.
[PICTURE] Tab
Function General Description Bright Adjusts the brightness.
Contrast Adjusts the contrast.
Gamma Switches the gamma mode.
Color Temp Switches the mode of color temperature.
Color Adjusts the strength of whole color.
Tint Adjusts the tint.
Sharpness Adjusts the sharpness.
My Memory Loads the data on the memory.
Reset Initialize the selected function
[-]: Decrease the brightness value. [+]: Increase the brightness value.
[-]: Decrease the contrast value. [+]: Increase the contrast value.
#1-Custom / #2-Custom / #3-Custom / #1-Default / #2-Default / #3-Default
Low / Middle / High / Custom
[-]: Decrease the color value. [+]: Increase the color value
[-]: Decrease the tint value. [+]: Increase the tint value.
[-]: Decrease the sharpness value. [+]: Increase the sharpness value.
Load1 / Load2 / Load3 / Load4
Saves the current adjustment data into the memory.
Save1 / Save2 / Save3 / Save4
[Execute]: Performs each function.
Bright / Contrast / Color / Tint / Sharpness
[Execute]: After the confirmation message, the selected function will be initialized.
19
Loading...
+ 43 hidden pages