3M 05028, 05029, 05046, 05002, B1773491 User Manual

...
0 (0)

3M™ Abrasive Products, 211K 04/14/14

Safety Data Sheet

Copyright,2014,3M Company.

All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon.

Document Group:

08-6225-0

Version Number:

6.06

Issue Date:

04/14/14

Supercedes Date:

02/24/14

SECTION 1: Identification

1.1. Product identifier

3M™ Abrasive Products, 211K

1.2. Recommended use and restrictions on use

Recommended use

Abrasive Product

1.3. Supplier’s details

3M

MANUFACTURER:

DIVISION:

Abrasive Systems Division

ADDRESS:

3M Center, St. Paul, MN 55144-1000, USA

Telephone:

1-888-3M HELPS (1-888-364-3577)

1.4. Emergency telephone number

1-800-364-3577 or (651) 737-6501 (24 hours)

SECTION 2: Hazard identification

2.1. Hazard classification

Not classified as hazardous according to OSHA Hazard Communication Standard, 29 CFR 1910.1200.

2.2. Label elements Signal word

Not applicable.

Symbols

Not applicable.

Pictograms

Not applicable.

2.3. Hazards not otherwise classified

None.

38% of the mixture consists of ingredients of unknown acute oral toxicity.

__________________________________________________________________________________________

Page 1 of 10

3M 05028, 05029, 05046, 05002, B1773491 User Manual

3M™ Abrasive Products, 211K 04/14/14

SECTION 3: Composition/information on ingredients

Ingredient

C.A.S. No.

% by Wt

Aluminum Oxide Mineral (non-fibrous)

1344-28-1

5 - 40

Filler

1317-65-3

0.5

- 10

Titanium Dioxide

13463-67-7

0.1

- 2

Quartz Silica

14808-60-7

0.001 - 0.12

Cured Adhesive

Mixture

3 - 40

Cloth Backing

Mixture

15 - 60

SECTION 4: First aid measures

4.1. Description of first aid measures

Inhalation:

Remove person to fresh air. If you feel unwell, get medical attention.

Skin Contact:

Wash with soap and water. If signs/symptoms develop, get medical attention.

Eye Contact:

Flush with large amounts of water. Remove contact lenses if easy to do. Continue rinsing. If signs/symptoms persist, get medical attention.

If Swallowed:

No need for first aid is anticipated.

4.2.Most important symptoms and effects, both acute and delayed

See Section 11.1. Information on toxicological effects.

4.3.Indication of any immediate medical attention and special treatment required

Not applicable

SECTION 5: Fire-fighting measures

5.1. Suitable extinguishing media

In case of fire: Use a fire fighting agent suitable for ordinary combustible material such as water or foam to extinguish.

5.2. Special hazards arising from the substance or mixture

None inherent in this product.

Hazardous Decomposition or By-Products

 

Substance

Condition

Carbon monoxide

During Combustion

Carbon dioxide

During Combustion

5.3. Special protective actions for fire-fighters

 

No unusual fire or explosion hazards are anticipated.

 

 

 

SECTION 6: Accidental release measures

 

6.1. Personal precautions, protective equipment and emergency procedures

__________________________________________________________________________________________

Page 2 of 10

3M™ Abrasive Products, 211K 04/14/14

Observe precautions from other sections.

6.2.Environmental precautions

Not applicable.

6.3.Methods and material for containment and cleaning up

Not applicable.

SECTION 7: Handling and storage

7.1. Precautions for safe handling

For industrial or professional use only. Avoid breathing of dust created by sanding, grinding or machining. Damaged product can break apart during use and cause serious injury to face or eyes. Check product for damage such as cracks or nicks prior to use. Replace if damaged. Always wear eye and face protection when working at sanding or grinding operations or when near such operations. Combustible dust may form by action of this product on another material (substrate). Dust generated from the substrate during use of this product may be explosive if in sufficient concentration with an ignition source. Dust deposits should not be allowed to accumulate on surfaces because of the potential for secondary explosions.

7.2. Conditions for safe storage including any incompatibilities

No special storage requirements.

SECTION 8: Exposure controls/personal protection

8.1. Control parameters Occupational exposure limits

Ingredient

C.A.S. No.

Agency

Limit type

Additional Comments

Filler

1317-65-3

US Dept of

TWA(as total dust):15

 

 

 

Labor - OSHA

mg/m3;TWA(respirable

 

 

 

 

fraction):5 mg/m3

 

Aluminum Oxide Mineral (non-

1344-28-1

Chemical

TWA:1 fiber/cc

 

fibrous)

 

Manufacturer

 

 

 

 

Rec Guid

 

 

Aluminum Oxide Mineral (non-

1344-28-1

US Dept of

TWA(as total dust):15

 

fibrous)

 

Labor - OSHA

mg/m3;TWA(respirable

 

 

 

 

fraction):5 mg/m3

 

Aluminum, insoluble compounds

1344-28-1

Amer Conf of

TWA(respirable fraction):1

 

 

 

Gov. Indust.

mg/m3

 

 

 

Hyg.

 

 

Titanium Dioxide

13463-67-7

Amer Conf of

TWA:10 mg/m3

 

 

 

Gov. Indust.

 

 

 

 

Hyg.

 

 

Titanium Dioxide

13463-67-7

Chemical

TWA(as respirable dust):5

 

 

 

Manufacturer

mg/m3

 

 

 

Rec Guid

 

 

Titanium Dioxide

13463-67-7

US Dept of

TWA(as total dust):15 mg/m3

 

 

 

Labor - OSHA

 

 

Quartz Silica

14808-60-7

Amer Conf of

TWA(respirable

 

 

 

Gov. Indust.

fraction):0.025 mg/m3

 

 

 

Hyg.

 

 

Quartz Silica

14808-60-7

US Dept of

TWA concentration(as total

 

 

 

Labor - OSHA

dust):0.3 mg/m3;TWA

 

 

 

 

concentration(respirable):0.1

 

__________________________________________________________________________________________

Page 3 of 10

Loading...
+ 7 hidden pages