3COM FlexWATCH 3110 User Manual

0 (0)

Network Video Server

User’s Manual

User’s Guide

FlexWATCHTM 3110

(Version. 3.0_Rev0)

Seyeon Technology Co., Ltd www.flexwatch.com www.intplus.es

Seyeon Tech Co., Ltd

- INTPLUS [2005] -

Network Video Server

User’s Manual

2

Seyeon Tech Co., Ltd

 

- INTPLUS [2005] -

Network Video Server

User’s Manual

Table of Contents

 

Overview of FlexWATCHTM Server..........................................................

10

1 Packing List..............................................................................................

10

2 What is FlexWATCHTM? ...............................................................................

11

2.1 Key Function of FlexWATCHTM..............................................................

11

2.2 Product Specification .........................................................................

12

2.3 Basic Network Connection Diagram......................................................

13

2.4 Application .......................................................................................

15

3 Hardware Description ................................................................................

17

3.1 Caution and observance .....................................................................

17

3.2 Hardware Description.........................................................................

17

IP assignment .......................................................................................

19

1 Key Words for Network ..............................................................................

19

2 Check Points before IP assignment ..............................................................

21

2.1 IP address........................................................................................

21

2.2 LAN cable or Cross-Over Cable............................................................

23

2.3 PC Environment ................................................................................

25

3 Factory Default .........................................................................................

25

4 IP Assignment ..........................................................................................

25

4.1 Through Installation Wizard Program ...................................................

25

4.2 IP Assignment through Hyper Terminal mode ........................................

28

Live view & Camera Configuration.........................................................

33

1 Live View .................................................................................................

33

3

Seyeon Tech Co., Ltd

 

- INTPLUS [2005] -

Network Video Server

User’s Manual

1.1 ActiveX based simple view..................................................................

33

1.2 Java Applet based live view ................................................................

34

1.3 Live view page guide .........................................................................

34

2 FW-Voyager based view and recording .........................................................

36

3 Camera configuration ................................................................................

36

3.1 Camera value string configuration........................................................

36

3.2 Camera configuration.........................................................................

38

3.3 Video Motion Detection ......................................................................

40

System Configuration............................................................................

43

1 System Information...................................................................................

43

2 Date & Time.............................................................................................

43

2.1 Date & Time in the server clock...........................................................

43

2.2 Date & Time using NTP server.............................................................

44

3 Admin Password Setup ..............................................................................

44

4 Access Control and User registration............................................................

44

4.1 Full Access .......................................................................................

45

4.2 Limited Access and User registration ....................................................

45

5 Frame rate control ....................................................................................

47

6 Tx Module Registration(NVCP).....................................................................

48

Network Configuration ..........................................................................

51

1 Network configuration................................................................................

51

1.1 Static IP ..........................................................................................

51

1.2 DHCP Client......................................................................................

51

4

Seyeon Tech Co., Ltd

 

- INTPLUS [2005] -

Network Video Server

User’s Manual

2 PPPoE Configuration ..................................................................................

53

3 Network port configuration .........................................................................

54

3.1 HTTP port configuration......................................................................

54

3.2 NVCP –Tx Port ..................................................................................

54

3.3 VDCP Port configuration .....................................................................

54

4 WAN Configuration and Application ..............................................................

55

4.1 External Modem connection ................................................................

55

4.2 Application with Dial-in/out feature......................................................

55

4.3 Dial Out configuration ........................................................................

56

4.4 Dial-in Configuration..........................................................................

58

5 Service Path.............................................................................................

59

6 AOIP Setup ..............................................................................................

60

6.1 How to use AOIP service ....................................................................

60

6.2 AOIP configuration ............................................................................

61

7 Network Status.........................................................................................

62

External Device connection & configuration ..........................................

63

1 Serial Ports Configuration Guide ..................................................................

63

1.1 Hardware Description.........................................................................

63

2 Installation & Configuration of External Device ..............................................

66

2.1 Console(Hyper Terminal cable connection) ............................................

66

2.2 Serial Input device ............................................................................

67

2.3 Serial output device...........................................................................

68

2.4 PTZ device connection and configuration ..............................................

70

2.5 Voice Kit Connection and configuration ................................................

73

5

Seyeon Tech Co., Ltd

 

- INTPLUS [2005] -

Network Video Server

User’s Manual

3 Alarm input device connection ....................................................................

75

4 Alarm Output(Relay output) device connection ..............................................

75

4.1 Alarm output device connection...........................................................

76

4.2 Manual control of Alarm output device..................................................

76

4.3 Automatic Control of Alarm Output device.............................................

77

Advanced Service configuration ............................................................

79

1 Buffering Service ......................................................................................

79

1.1 System and Pre Alarm Buffer memory..................................................

80

1.2 Buffer calculator................................................................................

82

2 Service Condition......................................................................................

84

2.1 Condition Setup ................................................................................

85

2.2 Criteria Setup ...................................................................................

86

3 e-mail configuration ..................................................................................

88

3.1 e-mail function configuration...............................................................

88

3.2 e-Mail condition set up.......................................................................

90

4 FTP Configuration......................................................................................

90

4.1 Directory option................................................................................

90

4.2 FTP service configuration....................................................................

93

5 Alarm Buffering Service .............................................................................

95

5.1 Alarm Buffering Service Configuration ..................................................

95

5.2 Playback of Pre/post alarm Image .......................................................

96

6 Sensor Notification service .........................................................................

97

Utilities..................................................................................................

99

1 Save Configuration....................................................................................

99

6

Seyeon Tech Co., Ltd

 

- INTPLUS [2005] -

Network Video Server

User’s Manual

2 Reboot ....................................................................................................

99

3 Factory Default .........................................................................................

99

4 System Update .......................................................................................

100

4.1 Description of files system................................................................

100

4.2 Update Procedure............................................................................

102

7

Seyeon Tech Co., Ltd

 

- INTPLUS [2005] -

Network Video Server

User’s Manual

Notice

The material in this document is for information only and is subject to change without notice. While reasonable efforts have been made in the preparation of this document to assure its accuracy, Seyeon Tech assumes no liability resulting from errors or omissions in this document, or from the use of the information contained herein.

Seyeon Tech reserves the right to make changes in the product design without reservation and without notification to its users.

Copyright

Copyright© 1999-2004 Seyeon Tech Co., Ltd. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written consent of Seyeon Tech Co., Ltd.

Copyright © 1999-2005 Seyeon Tech Co., Ltd.

810-12 Yeok Sam-dong,

Kang Nam-gu, SEOUL, 135-081,KOREA

TEL : 82 2 3017 0855

FAX : 82 2 3017 0843

URL : http://www.seyeon.co.kr http://www.flexwatch.com

8

Seyeon Tech Co., Ltd

 

- INTPLUS [2005] -

Network Video Server

User’s Manual

Warning

To prevent risk of electric shock, Do not remove system-case. No user serviceable parts inside. Any repair or modification for the product will be allowed to qualified service personal only.

Do not expose this appliance to water or moisture.

Do not install this product in Hazardous areas where highly combustible or explosive products are stored or used.

Important Information

Before installation, please read and observe all instructions and warnings contained in this manual. Retain this manual with the original receipt for future reference and warranty.

If any items are missing from the package when you open the box, please DO NOT install or OPERATRE FlexWATCHTM server. Contact the local Dealer or Distributor.

Please record following information for technical support and the track record in case of any theft or loss. Serial Number can be found underside of FlexWATCHTM server

Product Model :

Purchase Date :

Serial Number :

9

Seyeon Tech Co., Ltd

 

- INTPLUS [2005] -

Network Video Server

User’s Manual

Overview of FlexWATCHTM Server

1 Packing List

Please check and make sure following items are included in your package without any missing items.

If there are any missing items, please refer to your local distributor.

A.FlexWATCHTM 3110..…………………………………………………………………….1unit

B.RS-232 Serial cable…………………………………………………………………..…1unit (Cross cable DB9 Female)

C.Power Adapter…………………………………………………………………………..….1unit (Power Cable, SMPS DC 12V Adapter)

D.User’s Manual CD………………………………………………………….……………… 1unit

10

Seyeon Tech Co., Ltd

 

- INTPLUS [2005] -

Network Video Server

User’s Manual

2 What is FlexWATCHTM?

The FlexWATCHTM server is the Network Video Server, which transmits digital images captured by Analog CCD camera over the Internet. So users can view real-time live images over the Internet at anytime and anywhere using the standard web browser such as MS Internet Explorer or Netscape Communicator. There is no need other specific software to view real-time live images over the Internet. The FlexWATCHTM server is state-of-the art device and leads new generation of monitoring and security solution.

2.1 Key Function of FlexWATCHTM

Self contained stable system

Built-in Web server, Real time operation system and hardware video compression engines are included. No PC required to transmits real time video over the TCP/IP network.

High performance of video transmission

30fps (NTSC)/25FPS(PAL) per each channel and 120fps (NTSC)/100fps(PAL) for 4 cameras at 5kbps image size.

Channel based user authentication

Channel based multi user level protection for camera control, PTZ control, Alarm output and Audio control.

2400 frames Pre/Post video alarm buffer

2400 frames pre/post alarm buffer to store event triggered video in the internal memory.

Built-in Motion detection and time stamp

Built-in motion detection per each camera with up to 144 block of motion area to filter out unnecessary motion detection area. Optional time stamp on the video.

11

Seyeon Tech Co., Ltd

 

- INTPLUS [2005] -

Network Video Server

2.2 Product Specification

Hardware

·32bit Embedded CPU

·Flash 4Mbytes /SDRAM: 32Mbytes

·Hardware Motion JPEG engine

·Linux version 2.4.xx operating system

System Requirements

·OS : Windows 95/98/2000/XP/NT/ ME, Linux, Mac, Unix, Linux Operation system.

·Browser : MS Internet explorer( 5.x or above) Netscape( 6.x or above)

·PC H/W Pentium III 500M or above

·RAM: 64 MB and above

Network Protocols

· HTTP, TCP/IP, FTP, Telnet, RARP, PPP, PAP, CHAP, DHCP, SMTP client(e- mail), NTP, Java

Video

·NTSC: 704x480,704x240,352x240,176x112

·PAL : 704x576,704x288,352x288,176x144

·NTSC/PAL video auto sensing

· Frame Rate : 30fps 352X240 / 352x288

* based on Pentium4 2.0G and 100M dedicated network

· Image quality: 6 levels

Auxiliary Video-in & output

· 1 video inputs & 1 loop through outputs

LAN Interface

·10/100BaseT Ethernet auto negotiation

Alarm I/O interface

·1 Opto-coupled inputs or 1digital inputs

·1 Relay output

Serial Interface

· Two serial ports for console, modem (PSTN & GSM), serial input/output device, PTZ or voice kit

· Each port can be configured as RS-232, RS-485 or RS422(max 115kbit/s)

Security features

· Channel based multi user level protection for camera access, PTZ, Alarm I/O, Voice

· IP address Filtering / Image Encryption

Advanced Service

·Up to 5M Pre/Post alarm buffer memory

·Built-in Motion detections (Up to 144 blocks)

User’s Manual

·e-mail, FTP, alarm Buffer by event or schedule

·IP notification, Alarm Notification to e-mail, CGI path by event or schedule

PTZ & UART Control

·PTZ and UART device control through serial interface

·Up to 29 PTZ protocols from Panasonic Dome, Pelco “P” & “D” protocol, Sony EVID30, Kalateland AD Delta dome, Vicon Surveyor,CannonVC-C4 and etc. Refer to user guide for more vendors

·X10 device control

Others

·Video loss detection

·Up to 100 concurrent user access

·Dial in/out via PSTN or GSM modem

·Time stamp on Video

·Transmit Serial input data transfer with Video

·IP notification by e-mail

Developer support

·Provides HTTP CGI API

·ActiveX control development kit

Management

·Configurable by serial, web or telnet

·Remote system update via telnet, FTP or web browser.

Dimension

·Size: 122mm(W) x 84mm(D) x 35mm (H)

·Weight : 0.5kg without power supply

PWR Supply

· DC 12 Volt, 1.5Am, SMPS

Operating temp

· 40° ~ 125°F (5° ~ 50°C)

Approval

· FCC : Class A/ CE : Class A

Accessories

·Console cable for system set up/ LAN cable

·CD for User Guide, Installation wizard & Technical note

·Quick Installation guide

Miscellaneous

·Voice kit(FW-V10s) support

·Freely downloadable NDVR Software

·AVI conversion tool support by FW-voyager

·Work with FW-Manager NDVR S/W

12

Seyeon Tech Co., Ltd

 

- INTPLUS [2005] -

Network Video Server

User’s Manual

· Dynamic IP support through AOIP

2.3 Basic Network Connection Diagram

FlexWATCHTM server provides flexible connectivity with any type of networks available around you such as Leased line, Cable modem, xDSL line and PSTN (POT) line. Thus, it can be installed either in LAN or WAN environment as long as there is network available. But its configuration is subject to change depending on its environment. Following is basic network diagram for using FlexWATCHTM server.

Thus, you are required to consult with your network administrator or network consultant for more information. Also you are recommended to refer to Network configuration guide in the CD manual for more details.

2.3.1 Leased Line connection

Simply get a Static IP address from Network Administrator and assign IP address to FlexWATCHTM server and view from the Internet.

2.3.2 Static IP address from Cable modem or xDSL line

Simply get a Static IP address from Network Administrator or ISP and assign IP address to FlexWATCHTM server and view from the Internet

13

Seyeon Tech Co., Ltd

 

- INTPLUS [2005] -

Network Video Server

User’s Manual

2.3.3 Dynamic IP address from Cable or xDSL line

FlexWATCHTM server can be installed on even Dynamic IP network. But it needs to be registered in AOIP server which is an IP gateway running by Flexwatch.com or your local Distributor. For more details, please refer to Technical guide book in the CD manual.

2.3.4 Dial-up to AOIP server

Using Dial-up function of FlexWATCHTM server and AOIP service, you can set the FlexWATCHTM server to make a call to ISP and get it connected AOIP server. Once FlexWATCHTM server is registered in AOIP server, you can connect FlexWATCHTM server through AOIP server. Using this connection, you do not need to make multiple call or international call to FlexWATCHTM server, since FlexWATCHTM server will be connected by

14

Seyeon Tech Co., Ltd

 

- INTPLUS [2005] -

3COM FlexWATCH 3110 User Manual

Network Video Server

User’s Manual

your local Phone line based Internet connection.

2.3.5 Dial-in to FlexWATCHTM server through PSTN line

You can make a call to FlexWATCHTM server from anywhere and at anytime. But if you are concerned about call charge, we are recommending using above connection.

2.4 Application

Unlimited application for remote monitoring and surveillance solution can be built up using FlexWATCHTM server and its supporting peripheral Hardware and software such as FW-5000 or FW-5440 Network video recorder

server and FW-Manager DVR software.

Following could be simple application area where FlexWATCHTM server can be applied.

A. Building live home pager for advertising.

15

Seyeon Tech Co., Ltd

 

- INTPLUS [2005] -

Network Video Server

User’s Manual

B.ITS (Intelligent Traffic System) for real time monitoring

C.IBS (Intelligent Building System) using FlexWATCHTM Manager

D.Internet broadcasting

E.School, Kindergarten, Nursery, Franchised Restaurant & convenient store.

F.Facility monitoring

16

Seyeon Tech Co., Ltd

 

- INTPLUS [2005] -

Network Video Server

User’s Manual

3 Hardware Description

This chapter contains list of items to be prepared for the installation of FlexWATCHTM server.

Please carefully read this chapter before the installation.

Please prepare all the necessary items before start installation to prevent any possible malfunction or any other hazard can be happened during the installation.

3.1 Caution and observance

Keep the device in the clean and dried area where air ventilation is guaranteed. The device is not waterproof. The waterproof device or similar device must protect from any possible hazard by water or heavy moisture etc.

Regulated power supply is prerequisite for stable and optimal operation of the device. Use only power supply (SMPS 12V 1.5Am) supplied with FlexWATCHTM server. Manufacturer shall not liable for any hazard or shock caused by use of any other power supply.

To prevent risk of electric shock, do not remove system-case. No user serviceable parts inside. Any repair or modification for the product will be allowed to qualified service personal only

Use the cable supplied with FlexWATCHTM server. If you need to connect FlexWATCHTM server to the other device (External Modem, PTZ device), power on the devices before connect to the FlexWATCHTM server.

3.2 Hardware Description

3.2.1 FW-3110 Hardware Description

Front Panel View

A B C D E

17

Seyeon Tech Co., Ltd

 

- INTPLUS [2005] -

Network Video Server

User’s Manual

Menu Description

A

DC12V

DC 12V power

 

 

 

B

LAN

LAN Port for 10/100M Base T Auto sensing

 

 

 

C

COM

RS-232 port for serial input device, Voice kit, PTZ. Console

 

 

for Hyper Terminal must be connected to this port only.

 

 

 

D

LAN LED

Blinking only when LAN is connected to the network

 

 

Green-light on when LAN connection is OK

 

 

 

E

PWR LED

Indicate power on/off

 

 

Always red-light on when turned on

 

 

 

Rear Panel View

A B C D

ABNC IN/OUT 4Video input and 4 loop through video output

BGeneral I/O 1 Opto-coupled input and 1 output

CRS-232 RS-232 Port to connect Serial input device, Voice kit, PTZ

device or Modem.

F RS-485 To connect RS-485 based PTZ device. For more information, refer to External device configuration menu.

18

Seyeon Tech Co., Ltd

 

- INTPLUS [2005] -

Network Video Server

User’s Manual

IP assignment

1 Key Words for Network

LAN (Local Area Network) : Under the LAN network, any network device in the same LAN network can be accessed by any other network device. But LAN network can not be accessed from the Internet (WAN).

Most of case, LAN is built after Router which is connected to WAN network so that Network device in the local area network can access to the Internet through Router. Most of case, LAN networked device can not be accessed from the Internet (WAN), unless it is not configured to be accessed from the Internet through NAT function of router.

WAN (Wide Area Network) : WAN enables all network device can be accessed by each other over the Internet. It included Leased Line, Cable modem, xDSL, ISDN and Telephone line etc.

IP address : IP address is abbreviation of Internet Protocol address which allows all network devices can communicate other over the network using Internet protocol. Each network device has its own unit IP address whether or not it is in the LAN or WAN network. Therefore network devices can be accessed by other network device from either LAN or WAN (Internet).

For example, www.yahoo.com is a web server which has its own IP address so that any body can has access to Yahoo web site. Like most of public web site has its own IP address. Although IP address can not be seen by the client, domain name (www.yahoo.com) is automatically converted into IP address by DNS server.

Static IP address : A static IP address is an IP address permanently assigned to computer or network devices in a TCP/IP network. Static IP address is usually assigned to network devices which are consistently accessed by any users. For instances, www.yahoo.com has global static IP address. Thus, any body can access to the site. If you want to view live video stream from FlexWATCHTM server over the Internet, you need to assign Global Static IP address.

Depending the network Public Static IP(WAN) or Private Static IP can be assigned to network device.

19

Seyeon Tech Co., Ltd

 

- INTPLUS [2005] -

Network Video Server

User’s Manual

Dynamic IP address : A dynamic IP address is an IP address that is automatically assigned to a client station (computer, network equipment, etc.) in a TCP/IP network. Dynamic IP address is typically assigned by a DHCP server, which can be a computer on the network or another piece of hardware, such as router. A dynamic IP address may change every time your computer connects to the network

DHCP (Dynamic Host Configuration Protocol) : DHCP is software that automatically assigns IP addresses to client stations logging onto a TCP/IP network. DCHP eliminates troublesome job to manually assign permanent IP addresses to every device on your network. DHCP software typically runs in servers and is also found in network devices such as routers. Most of Cable Modem for Internet access uses DHCP Public IP address and Private IP address : Public IP address is an IP address which can be identified uniquely in Internet world. All IP addresses excluding private IP addresses are public IP addresses. Private IP addresses range from 10.0.0.0 until 10.255.255.255, and from 192.168.0.0 to 192.168.255.255. Generally speaking, private IP addresses are used in local area network which are hidden from the Internet world. Also, when public IP addresses not enough, private IP addresses are used while sharing global IP addresses

Router : Router is a network hardware which routes either Private or Public IP address to Public network so that network device between private IP network and Public IP network can communicate over the network. Router has NAT (Network Address Translation) function and through this function Public IP address will be mapped into private IP network so that Network device in the private IP address can be added from Internet.

Hub : Hub is a hardware which relay transmission between Router and Network device. There are two types of Hub. One is Dummy hub and the other one is Switching hub. Note that Hub will be used in the local network only.

NAT (Network Address Translation) : Network Address Translation (NAT) translates multiple IP addressed on the private LAN to one public address that is sent out to the Internet. This adds a level of security since the address of a PC connected to the private

20

Seyeon Tech Co., Ltd

 

- INTPLUS [2005] -

Network Video Server

User’s Manual

LAN is never transmitted on the Internet.

AOIP (Always On Internet Protocol) Server: AOIP™ server (Always On IP) is run by Seyeon Technology or its business partner and is a gateway for remote users to access FlexWATCH™ servers which is connected dynamic IP address over DSL,Cable modem and PSTN network over the Internet. FlexWATCH™ Network Video Server and Camera Server family is fully supported by AOIP server and any type of IP address(Global Dynamic IP or Private IP) can be assigned to FlexWATCHTM server and user can access FlexWATCH™ system from the Internet at anytime and anywhere through AOIP server.

2 Check Points before IP assignment

Following are list of item to be checked before you start configuration of FlexWATCHTM server.

2.1 IP address

You need to have Static IP address and other information such as Default Gateway and Network Mask which are to be assigned to FlexWATCHTM server. Please consult with your network administrator, if FlexWATCHTM server is to be installed in your corporate network, or consult with ISP if you want to install it in your home or shop for which DSL or Cable modem Internet service is available.

Following could be a simple way of finding IP address information of your PC and with that information you can set up IP address to FlexWATCHTM server in the private IP network without consulting to your ISP.

-Open DOS Command window as following procedure.

Program> Accessories > DOS Prompt

-Enter ‘ ipconfig’ command. Following information will come up

2.1.1 Static IP address enabled PC (DHCP Disabled PC)

You can easily check whether Static IP address is assigned to your PC. If you are in the Static IP network, it is simpler to assign IP address to FlexWATCHTM server than DHCP

21

Seyeon Tech Co., Ltd

 

- INTPLUS [2005] -

Network Video Server

User’s Manual

network.

\

C:\> ipconfig

Windows 2000/XP IP Configuration

Ethernet adapter Local area connection :

Connection-specific DNS Suffix . :

IP Address. . . . . . . . . . . .

: 192.168.0.158

Subnet Mask . . . . . . . . . .

. : 255.255.255.0

Default Gateway . . . . . . .

. . : 192.168.0.1

C:\>

With above info, you can get information about your network from your PC and see which IP class of IP address should be assigned to FlexWATCHTM server.

Note that the same class, but different IP address appeared in your PC must be used for FlexWATCHTM server to assign an IP address from your PC keeping Subnet mask & default gateway as same that of your PC.

For example, 192.168.0.155 or other available IP address except 192.168.0.158 can be assigned to FlexWATCHTM server, since it is the same class of your IP address and can be communicated in your local network.

If you want to check out whether 192.168.0.155 is available. Please try ping command in the DOS window. If there is any response, it means 192.168.0.155 is assigned to other network device. Thus, you need to randomly select other IP address and try ping test or consult with your network administrator

C:\> ping 192.168.0.155

Pinging 192.168.0.155 with 32 bytes of data:

22

Seyeon Tech Co., Ltd

 

- INTPLUS [2005] -

Network Video Server

User’s Manual

Reply from 192.168.0.155: bytes=32 time=10ms TTL=128

Reply from 192.168.0.155: bytes=32 time<10ms TTL=128

Reply from 192.168.0.155: bytes=32 time<10ms TTL=128

Reply from 192.168.0.155: bytes=32 time<10ms TTL=128

2.1.2 DHCP Enabled PC

If your PC is set to use DHCP, you need to check out IP address of your PC using ‘ ipconfig’ command at DOS Prompt window.

You need to get IP address from your network administrator to assign it to FlexWATCHTM server. IP address should be Surplus of IP address which will be not randomly assigned to any network device in your network.

Your network administrator must make sure that IP address should be excluded from IP pool when he configure Router.

Ethernet adapter Local Area Connection:

Connection-specific DNS Suffix . :

Description . . . . . . . . . . . : 3Com EtherLink III

ISA (3C509/3C509) in Legacy mode

Physical Address. . . . . . . . . : 00-60-08-3C-40-90

DHCP Enabled. . . . . . . . . . . : Yes

Autoconfiguration Enabled . . . . : Yes

IP Address. . . . . . . . . . . . : 192.168.0.158

Subnet Mask . . . . . . . . . . . : 255.255.255.0

Default Gateway . . . . . . . . . : 192.168.0.1

DHCP Server . . . . . . . . . . . : 192.168.0.1

DNS Servers . . . . . . . . . . . : 168.126.63.1

168.126.63.2

C:\>

2.2 LAN cable or Cross-Over Cable

Check out whether FlexWATCHTM server can be connected through LAN cable or Cross--

23

Seyeon Tech Co., Ltd

 

- INTPLUS [2005] -

Network Video Server

User’s Manual

over cable.

2.2.1 LAN Cable Environment

If your PC is connected to network through LAN cable, you need to connect FlexWATCHTM server to LAN port of Hub or Router.

2.2.2 Cross-over cable

If LAN network is not available, you can directly connect FlexWATCHTM server to your PC through Cross-over cable. In this case, you need to prepare Cross-over cable separately (Note that The LAN cable included in the product package is not Cross-over cable, but normal straight cable) and you need to set your PC IP address as 10.20.30.41 and connect the server with Factory default IP address, 10.20.30.40 through web browser.

Following is brief procedure to connect the server after changing PC IP address.

1)Click right button of your mouse on the ‘My Network Places’ icon in the main screen window.

2)Click right button of your mouse on the ‘Local area connection’ icon and select ‘Property’ option.

3)Select ‘Internet protocol (TCP/IP)’ option and click ‘Property’ icon.

4)Select ‘use the following IP address’ option from the TCP/IP property option and set the IP address as follow

-IP address : 10.20.30.41

-Network Mask : 255.255.255.0

5)Connect FlexWATCHTM server using Cross-over cable to your PC and run your web browser and enter default IP address, 10.20.30.40 of FlexWATCHTM server in the URL field. Note that Cross-over cable is not supplied with product.

6)Once you are connected to the server, click Admin icon and click LAN configuration menu.

7)Enter IP address you would like to assign to the FlexWATCHTM server and change your PC IP address again.

24

Seyeon Tech Co., Ltd

 

- INTPLUS [2005] -

Network Video Server

User’s Manual

2.3 PC Environment

Check out whether your PC is connected to LAN or WAN network or stand-alone. If stand alone, you need to use Cross-over cable or build up LAN environment to use LAN cable.

3 Factory Default

Please refer to the following factory defaults to change setting up.

 

Factory Default

 

 

Admin ID

root

Admin password

root

IP address

10.20.30.40

Network mask

255.255.255.0

4 IP Assignment

FlexWATCHTM server can be configured by two different configuration method and following is brief explanation.

Installation Wizard Program:

IP installation program is provided in CD form. Once FlexWATCHTM server is connected to LAN network, you can assign IP address through program and access the Web browser

HyperTerminal mode:

If no network is available and you want to set up IP address, you can directly connect FlexWATCHTM server to your PC through Serial cable provided together with product. HyperTerminal mode is very useful tool to recover Admin password when you lost your admin password or to report any problem to Manufacturer when product is on malfunction status.

4.1 Through Installation Wizard Program

IP setting with Installation Wizard program is easy and simple way and after IP setting is done you can do other configuration through web browser.

25

Seyeon Tech Co., Ltd

 

- INTPLUS [2005] -

Network Video Server

User’s Manual

You can use IP Installation Wizard Program through following step. (IPInstallationWizard.exe is provide in the product CD)

Preset a PC with Microsoft Windows O/S.

1)Connect FlexWATCHTM server into the network (Hub) that your PC belongs to.

2)Run the IP installation Wizard program in your PC. Then following IP Installation Wizard window will show up.

A

 

 

 

 

D

 

 

 

 

 

E

 

 

 

 

 

B

 

 

 

 

F

 

 

 

 

 

 

 

 

 

 

 

 

G

 

 

 

 

 

 

 

 

 

 

C

 

 

 

 

 

 

 

 

 

 

H

 

 

 

 

 

 

 

 

 

 

 

Description of Window

 

Menu

Description

 

 

 

A

Serial No. (MAC Address)

Enter FlexWATCHTM server Serial No. (Mac

 

of System

address) attached at the bottom of the unit and

 

 

select the LAN port.

 

 

WAN PORT is only for setting up FW-5000 and

 

 

FW-5440 model which has two LAN Card inside of

 

 

the box.

B

IP Address on PC

Auto scanned IP address of user’s computer with

 

 

IPInstallationWizard.exe running on.

 

 

 

26

Seyeon Tech Co., Ltd

 

- INTPLUS [2005] -

 

Network Video Server

User’s Manual

 

 

 

 

 

 

IP Address

Input an IP address to be assigned to

 

 

 

FlexWATCHTM server

 

 

 

Note that the IP must be directly connectable

 

 

 

with user’s PC. The above IP ’10.10.225.100’ is

 

 

 

only an example.

 

C

IP, Subnet, Gateway

Whether to change IP, Subnet and Gate or IP and

 

 

 

Subnet mask only.

 

D

Set IP Address’ Button

To activate a new IP assignment, click this

 

 

 

button.

 

E

Save IP Address’ Button

To save IP-Address in the Flash Memory.

 

 

 

 

 

F

Go to Home Page’ Button

To launch FlexWATCH Web browser and start

 

 

 

other configuration through Administration page.

 

G

‘Telnet to System’ Button

To guide you Telnet mode for Advanced

 

 

 

Configuration.

 

H

Result window

Show the result of IP assignment. If failed, try

 

 

 

again from the start or use other configuration

 

 

 

method

3)

Input the Serial No. (MAC address) and Select “LAN Port”.

 

 

 

 

4)

Input the IP address, which will be assigned to the system.

 

 

 

5)

Click “Set IP Address” button to save the above configuration.

 

 

6)

Check whether message type is correctly appeared on Result window as below.

 

 

 

 

 

 

 

 

 

------------ Set Server IP Address ------------

 

 

 

 

 

 

ARP: Adding static entry to ARP table

[

OK

]

 

 

 

Ping: Trying ping 10.10.225.100

[

OK

]

 

 

 

ARP: Deleting static entry from ARP table

[

OK

]

 

 

 

 

 

7)

If message come up as below, IP address setting has been failed.

 

 

 

 

 

 

 

 

 

------------ Set Server IP Address ------------

 

 

 

 

 

 

ARP: Adding static entry to ARP table

[

OK

]

 

 

 

Ping: Trying ping 10.10.225.100

[FAILED]

 

 

 

Please check whether IP address and MAC address is

 

 

 

valid.

 

 

 

 

 

 

Then, please retry again.

 

 

 

 

 

 

ARP: Deleting static entry from ARP table

[

OK

]

 

-If IP address setting is failed, please check whether correct IP/MAC address is entered. And try again with correct IP/MAC address, or please use HyperTerminal method.

-If the above result is O.K., follow the next step to finish Network Configuration.

27

Seyeon Tech Co., Ltd

 

- INTPLUS [2005] -

Network Video Server

User’s Manual

8)Click “Save IP Address” button to save IP-Address in the Flash Memory.

9)Click “Go to Home Page” button to access to FlexWATCHTM Web browser.

10)For server configuration, click “Admin” Icon and Input User ID and Password (Factory default is root : root) to get into configuration mode and then press “OK” button.

)Note

Once you changed the IP address of FlexWATCHTM server, you need to connect the server with the changed IP address. If you lost the IP address assigned to FlexWATCHTM server, you need to set-up a new IP address again.

)Note

If IP address set result is failed, please check whether correct IP/MAC address is entered. And try again with correct IP/MAC address, or please use HyperTerminal method.

4.2 IP Assignment through Hyper Terminal mode

Microsoft Windows provides Terminal emulation program, namely Hyper Terminal. For HyperTerminal connection, Power, RS-232 Cable and LAN cable must be connected to FlexWATCHTM server with user’s PC. LAN cable is to run Web browser after configuration using HyperTerminal. You can continue the below configuration after Network setting and the next process will be same as using Installation Wizard Program.

1)Link up with the provided serial cable between COM port at FW-3440 and COM1 or COM2 at user’s PC.

2)Run Hyper Terminal Program on user’s PC.

Window start> Program> Accessories> Communication> Hyper Terminal

3) If Hyper Terminal window come up as below, input HyperTerminal name (ex. Flexwatch) and press ‘OK’ button.

28

Seyeon Tech Co., Ltd

 

- INTPLUS [2005] -

Network Video Server

User’s Manual

4) Select the connected COM port with serial cable and press OK button.

5) When ‘Port Settings’ window show up, input each values from the table below.

Serial Port Settings

Value

 

 

Bits per Second

115200

Data bits

8

Parity

None

29

Seyeon Tech Co., Ltd

 

- INTPLUS [2005] -

Network Video Server

 

User’s Manual

 

Stop bits

1

 

 

Flow control

None

 

6) After setting Hyper Terminal, press Enter key several times and then you can see messages as below. Input Login ID and Password. (Factory defaults for Admin ID and Password are root/root.)

Seyeon Tech Co., Ltd. 2001-2003

Linux Kernel 2.4.20-syl1

FlexWATCH login:

7) If you correctly input Login ID and Password, ‘bash#’ prompt will show up as below.

FlexWATCH login: root

Password:

-----------------------------------------------------------

SYSTEM : FlexWATCH

VERSION : 3.0.040130 MODEL : FW-3110

-----------------------------------------------------------

login[504]: root login on `ttyS0'

bash#

8) Input ‘netconfig’ command after ‘bash# ’ prompt, and press Enter key. Then you can see following network setup values.

bash# netconfig

--------------------- Network(LAN) Setup ---------------------

Current configuation

IP Address : 10.20.30.40

Network Mask : 255.255.255.0

Gateway : 10.10.1.1

Enter IP Address :

9) Input new IP address, Network Mask and Gateway values to be assigned to FlexWATCHTM server. After this, press “y” to apply the new network configuration.

30

Seyeon Tech Co., Ltd

 

- INTPLUS [2005] -

Loading...
+ 75 hidden pages