3B SCIENTIFIC® PHYSICS
Binokulares Kursmikroskop, Modell 300 LED (115 V) 1013368 Binokulares Kursmikroskop, Modell 300 LED (230 V) 1013144
Bedienungsanleitung
01/14 ALF
1.Sicherheitshinweise
•Elektrischer Anschluss des Mikroskops darf nur an geerdeten Steckdosen erfolgen.
•
2. Beschreibung, technische Daten
Das binokulare Kursmikroskop ermöglicht die zweidimensionale Betrachtung von Objekten (dünne Schnitte von Pflanzenoder Tieren) in 40bis 1000-facher Vergrößerung.
Das Mikroskop 1013368 ist für eine Netzspannung von 115 V (±10 %) ausgelegt, 1013144 für 230 V (±10 %).
Stativ: Robustes Ganzmetallstativ, Stativarm fest mit Fuß verbunden; Fokussierung über beidseitig am Stativ angebrachte koaxiale Stellknöpfe für Feinund Grobtrieb, angetrieben über ein Zahnstangengetriebe mit Kugellager; einstellbarer Anschlag zum Schutz der Objektträger und Objektive
Tubus: Binokularer Siedentopf-Kopf, Schrägeinblick 30°, Kopf um 360° drehbar, Augenab-
1Okular
2Tubus
3Revolver mit Objektiven
4Objektführer
5Objekttisch
6Kondensor mit Irisblende und Filterhalter
7Beleuchtung
8Beleuchtungsregler
9Netzschalter
10Koaxialtrieb des Objekttisches
11Grobund Feintrieb
12Feststellschraube für Objekttisch
13Feststellschraube für Mikroskopkopf
14Stativ
stand zwischen 54 mm und 75 mm einstellbar, Dioptrienausgleich ±5 für beide Okulare
Okular: Weitfeld-Okularpaar WF 10x 18 mm
Objektive: Objektivrevolver mit 4 DIN achromatischen Objektiven 4x / 0,10, 10x / 0,25, 40x / 0,65, 100x / 1,25 Öl-Immersion, (mit Präparateschutz)
Vergrößerung: 40x, 100x, 400x, 1000x
Objekttisch: x-y-Kreuztisch, 125 x 130 mm2, mit Objektführer und koaxialen Stellknöpfen senkrecht zum Objekttisch, Stellbereich 70 x 30 mm2
Beleuchtung: Im Fuß integrierte regelbare LED-Beleuchtung
Spannungsversorgung: über Steckernetzgerät 6 V DC, 200 mA
Netzanschluss: 1013368: 115 V, 50/60 Hz; 1013144: 230 V, 50/60 Hz
Kondensor: Abbe Kondensor N.A.1,25 mit Irisblende, Filterhalter und Blaufilter, fokussierbar über ein Zahnstangengetriebe
Abmessungen: ca. 282 x 148 x 357 mm³ Masse: ca. 5,2 kg
1
3. Auspacken und Zusammenbau
Das Mikroskop wird in einem Karton aus Styropor geliefert.
•Nach Entfernen des Klebebands den Behälter vorsichtig öffnen. Dabei darauf achten, dass keine der optischen Teile (Objektive und Okulare) herausfallen.
•Um Kondensation auf den optischen Bestandteilen zu vermeiden, das Mikroskop so lange in der Verpackung belassen, bis es die Raumtemperatur angenommen hat.
•Das Mikroskop mit beiden Händen (eine Hand am Stativarm und eine am Fuß) entnehmen und auf eine ebene Fläche stellen.
•Die Objektive sind separat in Döschen verpackt. Sie werden in der Reihenfolge vom Objektiv mit dem kleinsten bis zum Objektiv mit dem größten Vergrößerungsfaktor im Uhrzeigersinn hinten beginnend in die Öffnungen der Revolverplatte geschraubt.
•Anschließend den Mikroskopkopf auf das Stativ setzen, mit der Feststellschraube fixieren und die Okulare in den Tubus einsetzen.
4.Bedienung
•Das Mikroskop auf einen ebenen Tisch stellen.
•Das zu betrachtende Objekt in die Mitte des Objekttisches platzieren und mit den Klemmen festklemmen.
•Netzkabel anschließen und Beleuchtung anschalten.
•Objektträger so in den Strahlengang schieben, dass das Objekt vom Strahlengang deutlich durchstrahlt wird.
•Augenabstand einstellen bis nur ein Lichtkreissichtbar ist.
•Diopterstärke den Augen anpassen.
•Zur Erreichung eines hohen Kontrasts Hintergrundbeleuchtung mittels der Irisblende und der regelbaren Beleuchtung einstellen.
•Das Objektiv mit der kleinsten Vergrößerung in den Strahlengang drehen. Ein Klick-Ton zeigt die richtige Stellung an.
Hinweis: Es ist am besten mit der kleinsten Vergrößerung zu beginnen, um zuerst größere Strukturdetails zu erkennen. Der Übergang zu einer stärkeren Vergrößerung zur Betrachtung feinerer Details erfolgt durch Drehen des Revolvers bis zum gewünschten Objektiv. Die Stärke der Vergrößerung ergibt sich aus dem Produkt des Vergrößerungsfaktors des Okulars und des Objektivs.
•Mit dem Triebknopf für Grobtrieb das unscharf abgebildete Präparat scharf stellen, dabei dar-
auf achten, dass das Objektiv den Objektträger nicht berührt. (Beschädigungsgefahr)
•Anschließend mittels Feintrieb die Bildschärfe einstellen.
•Zur Benutzung von Farbfiltern Filterhalter ausschwenken und Farbfilter einlegen.
•Mittels des Koaxialtriebs des Kreuztisches lässt sich das zu betrachtende Objekt auf die gewünschte Stelle schieben.
•Nach Gebrauch sofort die Beleuchtung ausschalten.
•Das Mikroskop mit keinen Flüssigkeiten in Kontakt kommen lassen.
•Das Mikroskop keinen mechanischen Belastungen aussetzen.
•Optische Teile des Mikroskops nicht mit den Fingern berühren.
•Bei Beschädigungen oder Fehlern das Mikroskop nicht selbst reparieren.
5.Aufbewahrung, Reinigung, Entsorgung
•Das Mikroskop an einem sauberen, trockenen und staubfreien Platz aufbewahren.
•Bei Nicht-Benutzung das Mikroskop immer mit der Staubschutzhülle abdecken.
•Das Mikroskop keinen Temperaturen unter 0°C und über 40°C sowie keiner relativen Luftfeuchtigkeit über 85% aussetzen.
•Vor Pflegeund Wartungsarbeiten ist immer der Netzstecker zu ziehen.
•Zur Reinigung des Mikroskops keine aggressiven Reiniger oder Lösungsmittel verwenden.
•Objektive und Okulare zum Reinigen nicht auseinander nehmen.
•Bei starker Verschmutzung das Mikroskop mit einem weichen Tuch und ein wenig Ethanol reinigen.
•Die optischen Bestandteile mit einem weichen Linsentuch reinigen.
•Die Verpackung ist bei den örtlichen Recyclingstellen zu entsorgen.
•Sofern das Gerät selbst verschrottet werden soll, so gehört dieses nicht in den normalen Hausmüll. Es sind die lokalen Vorschriften zur Entsorgung von Elektroschrott einzuhalten.
3B Scientific GmbH • Rudorffweg 8 • 21031 Hamburg • Deutschland • www.3bscientific.com Technische Änderungen vorbehalten
© Copyright 2014 3B Scientific GmbH
3B SCIENTIFIC® PHYSICS
Binocular Course Microscope Model 300 LED (115 V) 1013368 Binocular Course Microscope Model 300 LED (230 V) 1013144
Instruction Manual
01/14 ALF
1.Safety notes
•For power supply use only electrical sockets with ground contact.
2.Description, technical data
The binocular course microscope allows twodimensional viewing of objects (thin sections of plant or animal specimen) in 40x to 1000x magnification.
The microscope 1013368 is for operation with a mains voltage of 115 V (±10%), and the 1013144 unit is for operation with 230 V (±10%).
Stand: Robust, all metal stand with arm permanently connect to the base. Focussing by means of separate knobs for coarse and fine adjustment located on either side of the stand and operated by rack and pinion drive with ball bearings, adjustable stopper for protecting the object slides and objective
Tube: Binocular Siedentopf head, 30° viewing angle, 360° rotatable head, viewing distance adjustable between 54 and 75 mm, ±5 dioptric
1Eyepiece
2Tube
3Revolver with objectives
4Object guide
5Object stage
6Condensor with iris diaphragm and filter holder
7Lamp housing
8Illumination control
9Mains switch
10Adjustment knob for mechanical stage
11Adjustment knob for fine and coarse focusing
12Lock screw for object stage
13Head lock screw
14Stand
compensation for both eyepieces
Eyepiece: Pair of wide field eyepieces WF 10x 18 mm
Objectives: Revolver with 4 DIN achromatic objectives 4x / 0.10, 10x / 0.25, 40x / 0.65, 100x / 1.25 oil (with specimen protection)
Magnification: 40x, 100x, 400x, 1000x
Object stage: x-y cross table, 125 x 130 mm2, with object guide and coaxial adjustment knobs perpendicular to the object stage, adjustment range 70 x 30 mm2
Illumination: Adjustable LED lighting integrated in base
Power supply: Via plug-in power supply 6 V DC, 200 mA
Mains connection: 1013368: 115 V, 50/60 Hz; 1013144: 230 V, 50/60 Hz
Condenser: Abbe condenser N.A.1.25 NA 0.65 with iris diaphragm , filter holder and blue filter, focussed via rack and pinion drive
Dimensions: 282 x 148 x 357 mm³ approx. Weight: 5.2 kg approx.
1
3. Unpacking and assembly
The microscope is packed in a molded styrofoam container.
•Take the container out of the carton remove the tape and carefully lift the top half off the container. Be careful not to let the optical items (objectives and eyepieces) drop down.
•To avoid condensation on the optical components, leave the microscope in the original packing to allow it to adjust to room temperature.
•Using both hands (one around the pillar and one around the base), lift the microscope from the container and put it on a stable desk.
•The objectives will be found within individual protective vials. Install the objectives into the microscope nosepiece from the lowest magnification to the highest, in a clockwise direction from the rear.
•Put the head onto the top of the stand and tighten the head-lock-screw. Insert the eyepieces into the tube.
4.Operation
•Set the microscope on a level table.
•Place the object to be observed in the center of the object plate. Use the clips to fasten it into place. Make certain that the specimen is centered over the opening in the stage.
•Connect the mains cable to the net and turn on the switch to get the object illuminated.
•Make certain that the specimen is centered over the opening in the stage.
•Adjust the interpupillary distance so that one circle of light can be seen.
•Make the necessary eyepiece dioptre adjustments to suit your eyes.
•To obtain a high contrast, adjust the background illumination by means of the iris diaphragm and the variable illumination control.
•Rotate the nosepiece until the objective with the lowest magnification is pointed at the specimen. There is a definite “click” when each objective is lined up properly.
NOTE: It is best to begin with the lowest power objective. This is important to reveal general structural details with the largest field of view first. Than you may increase the magnification as needed to reveal small details. To determine the magnification at which you are viewing a specimen, multiply the power of the eyepiece by the power of the objective.
cused. Be careful that the objective does not make contact with the slide at any time. This may cause damage to the objective and/or crack your slide.
•Adjust the fine-focusing-knob to get the image more sharp and more clear.
•Colour filters may be inserted into the filter holder for definition of specimen parts. Swing the filter holder out and insert colour filters.
•Use the knobs of the mechanical stage to move the slide side-, backand forwards. The vernier provides accurate location of the specimen area.
•Always turn off the light immediately after use.
•Be careful not to spill any liquids on the microscope.
•Do not mishandle or impose unnecessary force on the microscope.
•Do not wipe the optics with your hands.
•Do not attempt to service the microscope yourself.
5.Storage, cleaning, disposal
•Keep the microscope in a clean, dry and dust free place.
•When not in use always cover the microscope with the dust cover.
•Do not expose it to temperatures below 0°C and above 40°C and a max. relative humidity of over 85%.
•Always unplug the mains plug before cleaning or maintenance.
•Do not clean the unit with volatile solvents or abrasive cleaners.
•Do not disassemble objective or eyepieces to attempt to clean them.
•Use a soft linen cloth and some ethanol to clean the microscope.
•Use a soft lens tissue to clean the optics.
•The packaging should be disposed of at local recycling points.
•Should you need to dispose of the equipment itself, never throw it away in normal domestic waste. Local regulations for the disposal of electrical equipment will apply.
•Adjust the coarse-focusing-knob which moves the stage up until the specimen is fo-
3B Scientific GmbH • Rudorffweg 8 • 21031 Hamburg • Germany • www.3bscientific.com Subject to technical amendments
© Copyright 2014 3B Scientific GmbH