Touch Screen Wireless Keypad
For Remote Control of the 2GIG Security System
INSTALL INSTRUCTIONS
This document describes the basic installation information for the 2GIG 2GIG TS1 and the steps necessary to “pair” (or learn in) the Touchscreen Wireless Keypad to the Control Panel.
Box Contents
•2GIG TS1
•AC Power Supply
•AC Power Supply Bracket
•Screws and anchors
TIP: The box contents will vary depending on whether the 2GIG TS1 was purchased as part of a kit or not.
BEFORE YOU BEGIN
Is the 900 MHz Transceiver installed in the Panel?
For the 2GIG TS1 to communicate with the Control Panel, the 900 MHz Transceiver (2GIG XCVR2) must be already be installed in the Control Panel.
2GIG-TS1 PRODUCT OVERVIEW
The Model 2GIG 2GIG TS1 Touch Screen Wireless Keypad is a remote control device that offers the functionality of a system keypad but also extends all user control of the 2GIG Control panel to other locations in a user’s home. Using the 2GIG TS1, users can control lights, thermostat and door locks and see the status of every zone in their home using the exact same and familiar interface found on the Control Panel. The keypad is designed for indoor use only.
IMPORTANT: Not for UL 985 installations.
The panel |
and |
buttons serve as controls as well as indicators. |
|
Pressing the |
|
(Emergency) button displays emergency icons on the |
|
display for Panic, |
Fire, and Emergency alarm activation (each has |
||
programmable options and can be enabled or disabled). Pressing the (Home) button changes the system display to the Home Screen. The keypad is powered from a plug in power supply. The 2GIG TS1 exchanges information through a secure 2 way wireless connection with the Control Panel.
NOTE: Before using the 2GIG TS1 it must be “learned” into the Control Panel.
Is the 2GIG-TS1 paired with the Control Panel?
The 2GIG TS1 and the Control Panel have to be paired to communicate with each other.
To check for to see if the 2GIG-TS1 is paired with the
Control Panel
Upon power up, the 2GIG TS1 displays the following screen:
Mounting Tools
Some special tools may be required to mount the 2GIG TS1 onto the wall:
•Screwdriver
•Pencil
•Wire stripper
•Staple gun
•Drywall saw (or equivalent)
•Ladder
PREPARING THE KEYPAD
1Remove the screw.
2Flip open the back cover of the 2GIG-TS1.
3Disconnect the hanging strap.
4Use the back cover as the mounting plate.
NOTE: Check that the 2GIG TS1 Keypad is functioning before selecting a location for the Keypad.
SELECTING A LOCATION FOR THE KEYPAD
1 Make sure that AC Power is available nearby.
TIP: Be careful of studs, electrical wires and pipes in the wall.
2Use the keypad’s back cover as a template to mark the screw holes with a pencil and the power (wiring) access hole.
3Use a drywall saw to cut the wiring hole.
Mounting the Keypad
1Use the 3 screws and anchors that are supplied to attach the mounting plate to the wall.
2Route 18 AWG wire between the keypad and the location of the power supply.
Wire Size and Length
To ensure proper operation, Do Not exceed the following maximum length for the wire size installed:
|
|
Wire Size |
Maximum Length |
22 AWG |
55 feet (16.8 meters) |
20 AWG |
85 feet (25.9 meters |
22 AWG 2 pairs |
110 feet (33.5 meters) |
(19 AWG equivalent) |
|
18 AWG |
135 feet (41.1 meters) |
To ensure that the appropriate wire size and length are installed, measure the voltage between the power connection terminals at the back of the control panel. The voltage measured must not fall below 11 volts DC or nuisance “AC Power Loss” messages may be displayed and reported.
NOTE: In the United States, wiring routed inside walls, ceilings, and floors must comply with requirements of the National Electrical Code, ANSI/NFPA 70 and local building codes. For wiring from the output of the 2GIG class II power supply, wiring rated CL2, CL2X, CL2R, or PLTC is recommended to satisfy these requirements. If this wiring is installed in an air plenum (space used for environmental air exchange) it must be rated CL2P (plenum rated).
2 ©2013 2GIG Technologies Inc. All Rights Reserved.
Connect the Power Wires to the Keypad
1Re connect the hanging strap.
2Use #6 insulated spade terminals (not supplied) to connect wires from the power supply to the keypad.
3 Close the keypad.
ASnap case closed.
BTighten case screw.
4 Connect the power wires to the power supply.
ALeft Terminal 14 VDC(+)
BRight Terminal 14 VDC (-)
C18 AWG/2-Conductor
Loading...