TECHNICAL GUIDE SPLIT-SYSTEM HEAT PUMPS 10 SEER – R-22
MODELS:
E*RA036 THRU 060
(3 THRU 5 NOMINAL TONS, 3 PH)
MODELS: 036-048 (3 PH)
MODELS: 060, 090 (3 PH)
|
ISO 9001 |
LISTED |
Certified Quality |
Management System |
Due to continuous product improvement, specifications are subject to change without notice.
Visit us on the web at www.york.com
Additional rating information can be found at www.ari.org/aridirectory.
279104-YTG-B-0307
DESCRIPTION
The 10 SEER Series heat pumps is the outdoor part of a versatile system of heat pumps. It is designed to be custommatched with one of UPG’s complete line of evaporator sections, with each serving a specific function. Matching Air Handlers are available for upflow, downflow, or horizontal applications to provide a complete system. Electric Heaters are available, if required. Add-On coils are available for use with upflow, downflow, or horizontal furnaces and air handlers.
WARRANTY
1-year limited parts warranty.
5-year limited compressor warranty.
FEATURES
•QUALITY COILS - The coil is constructed of copper tube and aluminum fins.
•COIL PROTECTION - Coils are protected from damage by a polymer mesh applied between the coil face, and a PVC coated steel coil guard.
•PROTECTED COMPRESSOR - The compressor is internally protected against high pressure and temperature. This is accomplished by the simultaneous operation of high pressure relief valve and a temperature sensor which protects the compressor if undesirable operating conditions occur. A liquid line filter-drier further protects the compressor.
•DURABLE FINISH - Cabinet is made of pre-painted steel. The pre-treated flat galvanized steel provides a better paint to steel bond, which resists corrosion and rust creep. Special primer formulas and matted-textured finish insure less fading when exposed to sunlight.
•LOWER INSTALLED COST - Installation time and costs are reduced by easy power and control wiring connections. Discharge line heat exchanger knockouts are provided, if required. Available in sweat connect models only. The unit contains enough refrigerant for matching indoor coils and 15 feet of interconnecting piping. The small base dimension means less space is required on the ground or roof.
•TOP DISCHARGE - The warm air from the top mounted fan is blown up away from the structure and any landscaping. This allows compact location on multi-unit applications.
•LOW OPERATING SOUND LEVEL - The upward air flow carries the normal operating noise away from the living area. The rigid top panel effectively isolates any motor sound. Isolator mounted compressor and the rippled fins of the condenser coil muffle the normal fan motor and compressor operating sounds.
•LOW MAINTENANCE - Long life permanently lubricated motor-bearings need no annual servicing.
•EASY SERVICE ACCESS - Fully exposed refrigerant connections, a single panel covering the electrical controls, and the molex plug in the control box connecting the condenser fan make for easy servicing of the unit.
•SECURED SERVICE VALVES - Secured re-usable service valves are provided on both the liquid and vapor sweat connections for ease of evacuating and charging.
•U.L. and C.U.L. listed - approved for outdoor application.
Certified in accordance with the Unitary Small Equipment certification program, which is based on ARI Standard 210/240.
FOR DISTRIBUTION USE ONLY - NOT TO BE USED AT POINT OF RETAIL SALE
279104-YTG-B-0307
Physical and Electrical Data
|
MODEL |
E1RA036S25 |
E2RA048S25 |
E1RA060S25 |
E1RA036S46 |
E2RA048S46 |
E1RA060S46 |
||
Unit Supply Voltage |
|
|
208/230-3-60 |
|
|
460 - 3 - 60 |
|
||
Normal Voltage Range 1 |
|
187 to 252 |
|
|
432 to 504 |
|
|||
Minimum Circuit Ampacity |
15.0 |
18.9 |
24.5 |
8.0 |
10.1 |
12.0 |
|||
Max. Qvercurrent Device Amps 2 |
25 |
30 |
40 |
15 |
15 |
20 |
|||
Compressor Type3 |
|
Inertia |
ScrollD |
ScrollC |
Inertia |
ScrollD |
ScrollC |
||
Compressor Amps |
|
Rated Load |
10.9 |
14.1 |
18.6 |
5.8 |
7.0 |
9.0 |
|
|
|
|
Locked Rotor |
78 |
125 |
128 |
40 |
55 |
63 |
Crankcase Heater |
|
|
Yes |
No |
No |
Yes |
No |
No |
|
Fan Motor Amps |
|
Rated Load |
1.4 |
1.3 |
1.3 |
.8 |
.7 |
.8 |
|
Fan Diameter Inches |
|
|
18 |
22 |
24 |
18 |
22 |
24 |
|
Fan Motor |
|
|
Rated HP |
1/4 |
1/4 |
1/4 |
1/4 |
1/5 |
1/4 |
|
|
|
Nominal RPM |
1,100 |
850 |
850 |
1,100 |
825 |
850 |
|
|
|
Nominal CFM |
2,750 |
3,500 |
3,100 |
2,750 |
3,500 |
3,100 |
Coil |
Face Area Sq. Ft. |
12.58 |
19.65 |
18.00 |
12.58 |
19.65 |
18.00 |
||
|
Rows Deep |
1 |
1 |
2 |
1 |
1 |
2 |
||
|
Fin / Inches |
14 |
13 |
14 |
14 |
13 |
14 |
||
Liquid Line |
Set OD (Field Installed) |
3/8 |
3/8 |
3/8 |
3/8 |
3/8 |
3/8 |
||
Vapor Line Set OD (Field Installed) |
3/4 |
7/8 |
7/8 |
3/4 |
7/8 |
7/8 |
|||
Unit Charge (Lbs. - Oz.) 4 |
5 - 12 |
8 - 3 |
11 - 3 |
5 - 12 |
8 - 3 |
11 - 3 |
|||
Charge Per Foot, Oz. |
|
.68 |
.70 |
.70 |
.68 |
.70 |
.70 |
||
Operating Weight Lbs. |
178 |
232 |
243 |
178 |
232 |
243 |
1.Rated in accordance with ARI Standard 110, utilization range “A”.
2.Dual element fuses or HACR circuit breaker.
3.All scrolls listed with a superscript “D” are Danfoss scrolls. All scrolls listed with a superscript “C” are Copeland scrolls.
4.The Unit Charge is correct for the outdoor unit, matched indoor coil and 15 feet of refrigerant tubing. For tubing lengths other than 15 feet, add or subtract the amount of refrigerant, using the difference in length multiplied by the per foot value.
All dimensions are in inches. They are subject to change without notice. Certified dimensions will be provided upon
Crequest.
|
|
DIMENSIONS |
|
|
|
|
|
|
|
Unit |
Dimensions |
|
Refrigerant |
||
A |
|
|
Connection |
||||
|
Model |
(Inches) |
|
||||
|
|
|
Service Valve Size |
||||
|
|
|
|
|
|
||
|
|
|
A1 |
B |
C |
Liquid |
Vapor |
|
|
036 |
25 |
35 |
23 |
|
3/4” |
|
|
048 |
33 |
37 |
27 |
3/8” |
7/8” |
|
B |
060 |
26 |
43 |
32 |
|
7/8” |
|
|
1. |
Including fan guard. |
|
|
|
2 |
Unitary Products Group |
|
|
|
|
|
279104-YTG-B-0307 |
|
Additional R-22 Charge / Orifice Size for Various Matched Systems |
|
|
||||
|
|
|
|
|
|
|
Outdoor Unit |
E1RA036S(25,46) |
|
E1RA048S(25,46) |
|
E1RA060S(25,46) |
|
Unit Orifice (s) 1 |
71, 81 |
|
81, 84, 87 |
|
99 |
|
Factory R-22 Charge, lbs-oz |
5 - 12 |
|
8 - 3 |
|
11 - 3 |
|
|
|
|
|
|
||
Indoor Coil |
|
System Orifice = Additional Charge, Oz |
|
|
||
FC/MC/PC35(B,C)3X |
81 + 8 |
|
– |
|
– |
|
FC/MC/PC/UC36(A,B,C)3X |
71 + 7 |
|
– |
|
– |
|
FC/MC/PC/UC42(B,C)3X |
81 + 8 |
|
– |
|
– |
|
FC/MC/PC/UC48C3X |
– |
|
87 + 6 |
|
– |
|
FC/MC/PC/UC48D3X |
– |
|
87 + 6 |
|
– |
|
FC/MC/PC/UC60C3X |
– |
|
84 + 4 |
|
99 + 0 |
|
FC/MC/PC/UC60D3X |
– |
|
84 + 4 |
|
99 + 0 |
|
AHP36C3X |
81 + 13 |
|
84 + 3 |
|
– |
|
AHP42C3X |
81 + 13 |
|
84 + 3 |
|
– |
|
AHP/SHP48D3X |
– |
|
84 + 4 |
|
99 + 0 |
|
AHP60D3X |
– |
|
84 + 4 |
|
99 + 0 |
|
G1NA036S17L |
71 + 7 |
|
– |
|
– |
|
G1NA048S21D |
71 + 7 |
|
81 + 8 |
|
– |
|
G1NA048S24P |
– |
|
81 + 8 |
|
– |
|
G1UA048S21/24 |
81 + 13 |
|
84 + 3 |
|
– |
|
G1UA060S24 |
– |
|
84 + 4 |
|
99 + 0 |
|
G1FA048S21/24 |
81 + 13 |
|
84 + 3 |
|
– |
|
G1FA060S24 |
– |
|
84 + 4 |
|
99 + 0 |
|
G2FD042S21 |
81 + 8 |
|
– |
|
– |
|
G2FD048S21/24 |
– |
|
87 + 6 |
|
– |
|
G2FD060S24 |
– |
|
84 + 4 |
|
99 + 0 |
|
FOOTNOTES: |
|
|
|
|
|
|
1. These orifices are packed in the instruction/warranty packet of each outdoor unit.
PROCEDURES:
1.Unit factory charge listed on the unit nameplate includes refrigerant for the condenser, the smallest evaporator and 15 feet of interconnecting line tubing.
2.Verify the orifice size and additional charge required for specific evaportor coil in the system using the above table.
3.Additional charge for the amount of interconnecting line tubing greater than 15 feet at the rate specified in the table above.
4.Permanently mark the unit nameplate with the total system charge. Total System Charge = Base Charge (as shipped) + adder for evaportor + adder for line set.
5.If the orifice in the evaportor was changed, verify the evaportor nameplate has been marked with the correct orifice size.
Unitary Products Group |
3 |
279104-YTG-B-0307
COOLING CAPACITY - With Air Handler Coils
|
AIR HANDLER |
|
COIL1 |
|
|
COOLING |
|
|
|||
|
|
|
|
|
|
|
|
|
|
||
UNIT MODEL |
|
ELECTRIC 2 |
|
RATED |
NET MBH |
SEER |
SEER |
|
|||
MODEL |
W |
MODEL |
EER |
||||||||
|
HEAT KW |
CFM |
|
|
W/O TXV |
WITH TXV3 |
|||||
|
TOTAL |
SENS. |
|||||||||
|
|
|
|
|
|||||||
|
|
3 PH 10 SEER HP WITH MA / MC / N-AH / G2FD |
|
|
|
|
|||||
|
MA12BN2,4 |
10 |
17 |
FC/MC35B3X |
1250 |
34.4 |
25.3 |
10 |
– |
8.95 |
|
|
|
|
|
|
|
|
|
|
|
|
|
E1RA036S(25,46) |
MA12BN2,4 |
10 |
17 |
FC/MC36B3X |
1250 |
34.4 |
25.3 |
10 |
– |
8.95 |
|
|
|
|
|
|
|
|
|
|
|
||
MA12BN2,4 |
10 |
17 |
FC/MC42B3X |
1250 |
34.4 |
25.3 |
10 |
– |
8.95 |
||
|
|||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
N1AHC1646 |
10, 15 |
21 |
G2FD042(S,H)21 |
1250 |
34.2 |
25.3 |
10 |
– |
8.95 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
MA16CN4 |
10, 15 |
21 |
FC/MC48C3X |
1600 |
45.5 |
33.7 |
10 |
– |
9.45 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
MA20DN2 |
10, 15, 25 |
24 |
FC/MC48D3X |
1725 |
45.5 |
33.7 |
10 |
– |
9.45 |
|
E2RA048S(25,46 |
|
|
|
|
|
|
|
|
|
|
|
MA20DN4 |
10, 15, 29 |
24 |
FC/MC48D3X |
1725 |
45.5 |
33.7 |
10 |
– |
9.45 |
||
|
|
|
|
|
|
|
|
|
|
|
|
|
N1AHC1646 |
10, 15 |
21 |
G2FD048(S,H)21 |
1600 |
45.5 |
33.7 |
10 |
– |
9.45 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
N1AHD2046 |
10, 15, 29 |
24 |
G2FD048(S,H)24 |
1600 |
45.5 |
33.7 |
10 |
– |
9.45 |
|
|
|
|
|
|
|
|
|
|
|
|
|
E1RA060S(25,46) |
MA20DN4 |
10, 15, 29 |
24 |
FC/MC60D3X |
2000 |
57.0 |
41.0 |
10 |
– |
9.80 |
|
|
|
|
|
|
|
|
|
|
|
||
N1AHD2046 |
10, 15, 29 |
24 |
G2FD048(S,H)24 |
1700 |
57.0 |
41.0 |
10 |
– |
9.80 |
||
|
|||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3 PH 10 SEER HP WITH AHP / SHP / F2RP / RC / FP / FC4,5 |
|
|
|
|
|||||
|
F2RP/FP036 |
5, 8, 10, 15, 19 |
21 |
– |
1250 |
34.0 |
24.9 |
10 |
– |
9.00 |
|
|
|
|
|
|
|
|
|
|
|
|
|
E1RA036S25 |
F2RD/FP042 |
5, 8, 10, 15 |
21 |
– |
1250 |
34.0 |
25.6 |
10 |
– |
9.00 |
|
|
|
|
|
|
|
|
|
|
|
||
AHP36C3X |
10, 15 |
21 |
– |
1250 |
34.0 |
25.6 |
10 |
– |
9.00 |
||
|
|||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
AHP42C3X |
10, 15, 18 |
21 |
– |
1250 |
34.0 |
25.6 |
10 |
– |
9.00 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
F2FP048 |
5, 8, 10, 15, 20, 25 |
24 |
– |
1600 |
45.0 |
33.5 |
10 |
– |
9.40 |
|
E2RA048S25 |
|
|
|
|
|
|
|
|
|
|
|
F2FP060 |
5, 8, 10, 15, 20, 25 |
24 |
– |
1600 |
46.5 |
34.4 |
10 |
– |
9.60 |
||
|
|
|
|
|
|
|
|
|
|
|
|
|
AHP/SHP48D3X |
10, 15, 18 |
24 |
– |
1600 |
46.5 |
34.4 |
10 |
– |
9.60 |
|
|
|
|
|
|
|
|
|
|
|
|
|
E1RA060S25 |
F2FP060 |
5, 8, 10, 15, 20, 25 |
24 |
– |
1700 |
56.0 |
40.0 |
10 |
– |
9.40 |
|
|
|
|
|
|
|
|
|
|
|
||
AHP/SHP60D3X |
10, 15 |
24 |
– |
1700 |
56.0 |
40.0 |
10 |
– |
9.40 |
||
|
|||||||||||
|
|
|
|
|
|
|
|
|
|
|
Rated in accordance with DOE test procedures (Federal Register 12-27-79 and 3-18-88) and ARI Standards 210/240. Cooling MBH based on 80°F entering air temperature, 50% RH, and rated air flow.
KW includes compressor, outdoor fan and indoor blower motor watts. Add-on coils include 365 watts/1000 CFM for blower motor.
EER (Energy Efficiency Ratio) is the total cooling output in BTU’s at a 95°F outdoor ambient divided by the total electric power in watt-hours at those conditions. SEER (Seasonal Energy Efficiency Ratio) is the total cooling output in BTU’s during a normal annual usage period for cooling divided by the total electric power input in watt-hours during the same period.
1.G2FD coils available with a factory installed horizontal drain pan. See price pages for specific model number.
2.Single phase units require single phase 2HK heaters.
3.TXV = Use 1TV700 Series Kit.
4.To meet R=4.2 insulation requirements, substitute F2FP for F2RP, and F2FC for F2RC. models. All ratings remain the same.
5.FG8, FG9, and FL8 furnaces and F2RP / F2RC air handlers have B.O.D. standard.
-= Not applicable
4 |
Unitary Products Group |
279104-YTG-B-0307
COOLING CAPACITY - Upflow, Downflow, & Horizontal Furnaces and Coils
|
FURNACE** |
COIL |
|
|
|
COOLING |
|
|
||
|
|
|
|
|
|
|
|
|
|
|
UNIT MODEL |
CFM RANGE |
|
RATED |
NET MBH |
|
SEER |
SEER + TXV1 |
|
||
W |
MODEL |
|
EER |
|||||||
|
(MIN.-MAX.) |
|
|
CFM |
TOTAL |
SENS. |
|
W/O TXV |
+ TDR* |
|
|
|
21,24 |
G1FA048S21 |
1250 |
34.4 |
24.7 |
|
10 |
– |
9.05 |
|
|
|
|
|
|
|
|
|
|
|
|
|
17 |
G1NA036S17L |
1250 |
35.0 |
26.2 |
|
10 |
– |
9.00 |
|
|
|
|
|
|
|
|
|
|
|
|
|
21 |
G1NA048S21D |
1250 |
35.0 |
26.2 |
|
10 |
– |
8.95 |
|
1100 |
|
|
|
|
|
|
|
|
|
E1RA036S(25,46 |
21,24 |
G1UA048S21 |
1250 |
34.4 |
24.7 |
|
10 |
– |
9.05 |
|
1400 |
|
|
|
|
|
|
|
|
|
|
21 |
G2FD042S21 |
1250 |
34.2 |
25.3 |
|
10 |
– |
8.95 |
||
|
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
17,21 |
FC/MC/PC35*3X |
1250 |
34.4 |
24.7 |
|
10 |
– |
9.5 |
|
|
|
|
|
|
|
|
|
|
|
|
|
14,17,21 |
FC/MC/PC/UC36*3X |
1250 |
34.4 |
24.7 |
|
10 |
– |
9.5 |
|
|
|
|
|
|
|
|
|
|
|
|
|
17,21 |
FC/MC/PC/UC42*3X |
1250 |
34.4 |
24.7 |
|
10 |
– |
9.5 |
|
|
|
|
|
|
|
|
|
|
|
|
|
21,24 |
G1FA048S21 |
1600 |
45.5 |
32.7 |
|
10 |
– |
9.30 |
|
|
|
|
|
|
|
|
|
|
|
|
|
21 |
G1NA048S21D |
1600 |
45.0 |
31.2 |
|
10 |
– |
9.50 |
|
1400 |
|
|
|
|
|
|
|
|
|
E2RA048S(25,46 |
21,24 |
G1UA048S21 |
1600 |
45.5 |
32.7 |
|
10 |
– |
9.30 |
|
1800 |
|
|
|
|
|
|
|
|
|
|
21,24 |
G2FD048(S,H)21,24 |
1600 |
45.5 |
33.7 |
|
10 |
– |
9.40 |
||
|
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
21 |
FC/MC/PC/UC48C3X |
1600 |
45.5 |
32.7 |
|
10 |
– |
9.30 |
|
|
|
|
|
|
|
|
|
|
|
|
|
24 |
FC/MC/PC/UC48D3X |
1600 |
45.5 |
32.7 |
|
10 |
– |
9.30 |
|
|
|
|
|
|
|
|
|
|
|
|
|
21,24 |
G1FA060S21,24 |
1700 |
57.0 |
41.0 |
|
10 |
– |
9.80 |
|
|
|
|
|
|
|
|
|
|
|
|
1600 |
21,24 |
G1UA060S21,24 |
1700 |
57.0 |
41.0 |
|
10 |
– |
9.80 |
|
|
|
|
|
|
|
|
|
|
|
E1RA060S(25,46) |
24 |
G2FD060(S,H)24 |
1700 |
57.0 |
41.0 |
|
10 |
– |
9.80 |
|
2100 |
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
21 |
FC/MC/PC/UC60C3X |
1725 |
57.0 |
41.0 |
|
10 |
– |
9.80 |
|
|
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
24 |
FC/MC/PC/UC60D3X |
2000 |
57.0 |
41.0 |
|
10 |
– |
9.80 |
|
|
|
|
|
|
|
|
|
|
|
1. TXV = Use 1TV700 Series Kit. |
|
|
|
|
|
|
|
|
*Requires a 2FD Blower Time Delay unless a standard furnace is equipped with one.
**Refer to Quick Selection Chart for specific furnace match-up.
Unitary Products Group |
5 |