LP-3 Assembly Instructions
|
CAUTION |
|
|
|
4 Attach the braces. |
|
|
|
|
|
|
|
1Attach the braces to the center of the upper beam using |
||||
|
|
|
|
|
|
|||
• Be careful not to confuse parts, and be sure to install all parts |
the short screws (B). Do not tighten the screws yet. |
|||||||
|
in the correct direction. Please assemble in accordance with |
(B) |
|
|
||||
|
the sequence given below. |
|
|
|
|
|
||
• Assembly should be carried out by at least two persons. |
|
|
Correct |
|||||
• Be sure to use the correct screw size, as indicated below. Use |
|
|
tightenning |
|||||
|
of incorrect screws can cause damage. |
|
|
|
|
|
||
• |
Be sure to tighten up all screws upon completing assembly of |
(A) |
(A) |
Insufficient |
||||
|
each unit. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
tightenning |
|
• |
To disassemble, reverse the assembly sequence given below. |
|
|
|
||||
• |
If the main unit creaks or is otherwise unsteady when you play |
2Attach the stays to the side panels using the remaining |
||||||
|
on the keyboard, refer to the assembly diagrams and retighten |
|||||||
|
long screws (A). Again, do not tighten the screws yet. |
|||||||
|
all screws. |
|
|
|
|
|||
|
|
|
|
|
3Tighten the screws when all four are in place. |
|||
|
|
|
|
|
|
|||
|
Assembly procedure |
|
|
5 Set the attachments. |
|
|
||
1 You will need a Phillips screwdriver to assemble the |
|
|
||||||
Note: Fix them using small screws (C). |
|
|||||||
|
stand. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Attach- |
|
|
|
|
|
|
|
|
ments |
|
|
|
|
|
|
|
|
Small screws |
|
2 Open the box and remove all parts. Make sure that all |
|
(C) |
|
|||||
|
|
|
||||||
|
of the parts are included. |
|
|
|
|
|
||
|
Screw set (VS64540) |
|
|
|
|
|
|
|
|
(A) Long screws |
(B) Short screws |
(C) Small screws |
(D) Caps |
(E) Knob bolts |
|
|
|
|
(6 x 30 mm) |
(6 x 16 mm) |
(4 x 8 mm) |
|
(6 x 40 mm) |
|
|
|
|
|
|
|
|
|
6 Attach the keyboard to the stand. |
|
|
|
6 pcs. |
2 pcs. |
4 pcs. |
4 pcs. |
4 pcs. |
1 After making sure that the keyboard and the stand are |
||
|
|
|
|
|
|
both facing in the same direction, place the keyboard on |
||
|
|
|
|
|
|
the stand so that the holes of the stand are aligned with |
||
|
|
Upper beam |
|
Attachments |
the holes in the bottom of the keyboard. |
|||
|
Right |
Left |
|
|
Note: Be careful not to let your finger get caught between the |
|||
|
|
|
|
|||||
|
side |
|
side |
|
|
stand and the keyboard. |
|
|
|
panel |
|
panel |
4 pcs. |
|
|
|
|
|
|
Braces 2 pcs. |
|
|
|
Hand |
Hand |
|
|
|
|
|
|
|
(identical) |
Do not hold the LP-3 in the |
|
|
|
|
shaded areas, to avoid |
Danger |
Bottom of the |
Danger |
|
getting your fingers |
keyboard |
||
|
caught. |
|
|
|
Hand |
Hand |
3Attach the upper beam and cap (D).
Notes: Tighten four long screws (A) loosely at first, then do
them hardly to set each screw in place correctly. |
Slide the keyboard from |
||
When inserting the screws, turn them in loosely at |
|||
rear to front as your place |
|||
first, then tighten them after making sure the upper |
it on the stand to align |
||
beam is positioned correctly. |
|
the bolt holes. |
|
1Secure the upper beam |
Correct |
|
|
with long screws (A). |
tightenning |
|
|
2Attach the caps (D). |
|
2Secure the keyboard using the knob bolts (E). |
|
Insufficient |
Note: Do not tighten the bolts until all four bolts are in place. |
||
|
|||
|
tightenning |
|
M.D.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation
©1994, 2003 Yamaha Corporation