U
HTR-5850/HTR-5840
AV Receiver
OWNER'S MANUAL
IMPORTANT SAFETY INSTRUCTIONS
CAUTION |
RISK OF ELECTRIC SHOCK |
DO NOT OPEN |
CAUTION: TO REDUCE THE RISK OF |
ELECTRIC SHOCK, DO NOT REMOVE |
COVER (OR BACK). NO USER-SERVICEABLE |
PARTS INSIDE. REFER SERVICING TO |
QUALIFIED SERVICE PERSONNEL. |
•Explanation of Graphical Symbols
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
1Read Instructions – All the safety and operating instructions should be read before the product is operated.
2Retain Instructions – The safety and operating instructions should be retained for future reference.
3Heed Warnings – All warnings on the product and in the operating instructions should be adhered to.
4Follow Instructions – All operating and use instructions should be followed.
5Cleaning – Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
6Attachments – Do not use attachments not recommended by the product manufacturer as they may cause hazards.
7Water and Moisture – Do not use this product near water – for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.
8Accessories – Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.
9A product and cart combination should be moved with care. Quick stops, excessive force, and uneven
surfaces may cause the product and cart combination to overturn.
10Ventilation – Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.
11Power Sources – This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.
12Grounding or Polarization – This product may be equipped with a polarized alternating current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.
13Power-Cord Protection – Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.
14Lightning – For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.
15Power Lines – An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
16Overloading – Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.
17Object and Liquid Entry – Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.
18Servicing – Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
19Damage Requiring Service – Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:
a)When the power-supply cord or plug is damaged,
b)If liquid has been spilled, or objects have fallen into the product,
c)If the product has been exposed to rain or water,
i
d)If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation,
e)If the product has been dropped or damaged in any way, and
f)When the product exhibits a distinct change in perfor-
mance - this indicates a need for service.
20Replacement Parts – When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
21Safety Check – Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.
22Wall or Ceiling Mounting – The unit should be mounted to a wall or ceiling only as recommended by the manufacturer.
23Heat – The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.
IMPORTANT SAFETY INSTRUCTIONS
24Outdoor Antenna Grounding – If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING
MAST |
ANTENNA |
|
LEAD IN |
|
WIRE |
GROUND |
|
CLAMP |
|
|
ANTENNA |
|
DISCHARGE UNIT |
|
(NEC SECTION 810–20) |
ELECTRIC |
|
SERVICE |
|
EQUIPMENT |
GROUNDING CONDUCTORS |
|
|
|
(NEC SECTION 810–21) |
|
GROUND CLAMPS |
|
POWER SERVICE GROUNDING |
|
ELECTRODE SYSTEM |
|
(NEC ART 250. PART H) |
NEC – NATIONAL ELECTRICAL CODE |
|
FCC INFORMATION (for US customers)
1IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.
2IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA.
3NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices.
This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices.
Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures:
Relocate either this product or the device that is being affected by the interference.
Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA 90620.
The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.
ii
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference.
2Install this sound system in a well ventilated, cool, dry, clean place – away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold. Allow ventilation space of at least 30 cm on the top, 20 cm on the left and right, and 20 cm on the back of this unit.
3Locate this unit away from other electrical appliances, motors, or transformers to avoid humming sounds.
4Do not expose this unit to sudden temperature changes from cold to hot, and do not locate this unit in a environment with high humidity (i.e. a room with a humidifier) to prevent condensation inside this unit, which may cause an electrical shock, fire, damage to this unit, and/or personal injury.
5Avoid installing this unit where foreign object may fall onto this unit and/or this unit may be exposed to liquid dripping or splashing. On the top of this unit, do not place:
–Other components, as they may cause damage and/or discoloration on the surface of this unit.
–Burning objects (i.e. candles), as they may cause fire, damage to this unit, and/or personal injury.
–Containers with liquid in them, as they may fall and liquid may cause electrical shock to the user and/or damage to this unit.
6Do not cover this unit with a newspaper, tablecloth, curtain, etc. in order not to obstruct heat radiation. If the temperature inside this unit rises, it may cause fire, damage to this unit, and/or personal injury.
7Do not plug in this unit to a wall outlet until all connections are complete.
8Do not operate this unit upside-down. It may overheat, possibly causing damage.
9Do not use force on switches, knobs and/or cords.
10When disconnecting the power cord from the wall outlet, grasp the plug; do not pull the cord.
11Do not clean this unit with chemical solvents; this might damage the finish. Use a clean, dry cloth.
12Only voltage specified on this unit must be used. Using this unit with a higher voltage than specified is dangerous and may cause fire, damage to this unit, and/or personal injury. YAMAHA will not be held responsible for any damage resulting from use of this unit with a voltage other than specified.
13To prevent damage by lightning, disconnect the power cord from the wall outlet during an electrical storm.
14 Do not attempt to modify or fix this unit. Contact qualified YAMAHA service personnel when any service is needed. The cabinet should never be opened for any reasons.
15 When not planning to use this unit for long periods of time (i.e. vacation), disconnect the AC power plug from the wall outlet.
16 Be sure to read the “TROUBLESHOOTING” section on common operating errors before concluding that this unit is faulty.
17 Before moving this unit, press STANDBY/ON to set this unit in the standby mode, and disconnect the AC power plug from the wall outlet.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
This unit is not disconnected from the AC power source as long as it is connected to the wall outlet, even if this unit itself is turned off. This state is called the standby mode. In this state, this unit is designed to consume a very small quantity of power.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to wide slot and fully insert.
This Class B digital apparatus complies with Canadian ICES-003.
IMPORTANT
Please record the serial number of this unit in the space below.
MODEL:
Serial No.:
The serial number is located on the rear of the unit. Retain this Owner’s Manual in a safe place for future reference.
We Want You Listening For A Lifetime
YAMAHA and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or distortion – and, most importantly, without affecting your sensitive hearing.
Since hearing damage from loud sounds is often undetectable until it is too late, YAMAHA and the Electronic Industries Association’s Consumer Electronics Group recommend you to avoid prolonged exposure from excessive volume levels.
iii
CONTENTS
INTRODUCTION |
|
FEATURES............................................................. |
2 |
GETTING STARTED............................................ |
3 |
Supplied accessories .................................................. |
3 |
Installing batteries in the remote control ................... |
3 |
CONTROLS AND FUNCTIONS ......................... |
4 |
Front panel ................................................................. |
4 |
Remote control........................................................... |
6 |
Using the remote control ........................................... |
7 |
Front panel display .................................................... |
8 |
Rear panel ................................................................ |
10 |
PREPARATION |
|
SPEAKER SETUP ............................................... |
11 |
Speaker placement ................................................... |
11 |
Speaker connections ................................................ |
12 |
CONNECTIONS .................................................. |
14 |
Before connecting components................................ |
14 |
Connecting video components................................. |
16 |
Connecting audio components................................. |
19 |
Connecting the FM and AM antennas ..................... |
20 |
Connecting the power supply cord .......................... |
21 |
Speaker impedance setting ...................................... |
21 |
Turning on the power............................................... |
22 |
BASIC SETUP ...................................................... |
23 |
Using the BASIC SETUP menu .............................. |
23 |
BASIC OPERATION |
|
PLAYBACK.......................................................... |
26 |
Basic operations....................................................... |
26 |
Selecting sound field programs ............................... |
28 |
Selecting input modes.............................................. |
32 |
FM/AM TUNING ................................................. |
34 |
Automatic and manual tuning.................................. |
34 |
Presetting stations .................................................... |
35 |
Selecting preset stations........................................... |
37 |
Exchanging preset stations ...................................... |
38 |
XM SATELLITE RADIO TUNING .................. |
40 |
What is XM Satellite Radio? ................................... |
40 |
XM Satellite Radio connections .............................. |
40 |
XM Satellite Radio functions .................................. |
41 |
Activating XM Satellite Radio ................................ |
42 |
Basic XM Satellite Radio operations....................... |
43 |
XM Satellite Radio search modes............................ |
44 |
Setting XM Satellite Radio preset channels ............ |
47 |
RECORDING ....................................................... |
50 |
SOUND FIELD PROGRAMS |
|
SOUND FIELD PROGRAM |
|
DESCRIPTIONS............................................... |
51 |
For movie/video sources.......................................... |
51 |
For music sources .................................................... |
53 |
ADVANCED OPERATION |
|
ADVANCED OPERATIONS .............................. |
54 |
Using the sleep timer ............................................... |
54 |
Manually adjusting speaker levels........................... |
55 |
SET MENU ............................................................ |
56 |
Using SET MENU................................................... |
57 |
1 SOUND MENU.................................................... |
58 |
2 INPUT MENU...................................................... |
60 |
3 OPTION MENU................................................... |
61 |
ADVANCED SETUP MENU............................... |
63 |
REMOTE CONTROL FEATURES ................... |
65 |
Control area ............................................................. |
65 |
Setting remote control codes ................................... |
66 |
Controlling other components ................................. |
67 |
Switching library codes <Except for HTR-5840: |
|
U.K. and Europe models> ................................... |
68 |
Clearing set up remote control codes....................... |
68 |
ADDITIONAL INFORMATION |
|
EDITING SOUND FIELD PARAMETERS ...... |
69 |
What is a sound field ............................................... |
69 |
Changing parameter settings ................................... |
69 |
SOUND FIELD PARAMETER |
|
DESCRIPTIONS............................................... |
71 |
TROUBLESHOOTING ....................................... |
73 |
RESETTING THE FACTORY PRESETS ........ |
77 |
GLOSSARY........................................................... |
78 |
Audio formats .......................................................... |
78 |
Sound field programs............................................... |
79 |
Audio information ................................................... |
79 |
Video signal information ......................................... |
80 |
SPECIFICATIONS............................................... |
81 |
INTRODUCTION |
|
|
|
|
|
PREPARATION |
|
|
|
|
|
OPERATION |
BASIC |
|
|
|
|
PROGRAMS |
FIELD SOUND |
|
|
|
|
OPERATION |
ADVANCED |
|
|
|
|
INFORMATION |
ADDITIONAL |
|
|
1
FEATURES
Built-in 6-channel power amplifier
Minimum RMS output power
[ HTR-5850 ]
(0.06% THD, 20 Hz to 20 kHz, 8 Ω) Front: 90 W + 90 W
Center: 90 W Surround: 90 W + 90 W Surround back: 90 W
[ HTR-5840 ]
(0.06% THD, 20 Hz to 20 kHz, 8 Ω) Front: 85 W + 85 W
Center: 85 W Surround: 85 W + 85 W Surround back: 85 W
Sound field features
Proprietary YAMAHA technology for the creation of sound fields
Dolby Digital/Dolby Digital EX decoder
DTS/DTS-ES Matrix 6.1, Discrete 6.1, DTS Neo:6, DTS 96/24 decoder
Dolby Pro Logic/Dolby Pro Logic II/ Dolby Pro Logic IIx decoder
Virtual CINEMA DSP
SILENT CINEMA™
Sophisticated AM/FM tuner
40-station random and direct preset tuning
Automatic preset tuning
Preset station shifting capability (preset editing)
XM Satellite Radio
XM Satellite Radio programming (using the “XM Connect and Play digital antenna”, sold separately)
Other features
192-kHz/24-bit D/A converter
A SET MENU that provides you with items for optimizing this unit for your audio/video system
6 additional input jacks for discrete multi-channel input
S-video signal input/output capability
Component video input/output capability
Optical and coaxial digital audio signal jacks
Sleep timer
Cinema and music night listening modes
Remote control with preset remote control codes
[ HTR-5850 ]
Video signal conversion (Composite video ↔ S-video → Component video) capability for monitor out
•This document is the owner’s manual for both HTR-5850 and HTR-5840. Model names are given where the details of functions are unique to each model. Illustrations for HTR-5850 are mainly used for explanations.
•y indicates a tip for your operation.
•Some operations can be performed by using either the buttons on the main unit or on the remote control. In cases when the button names differ between the main unit and the remote control, the button name on the remote control is given in parentheses.
•This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In case of differences between the manual and product, the product has priority.
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, “Surround EX”, and the double-D symbol are trademarks of Dolby Laboratories.
“SILENT CINEMA” is a trademark of YAMAHA CORPORATION.
“DTS”, “DTS-ES”, “Neo:6” and “DTS 96/24” are trademarks of Digital Theater Systems, Inc.
The XM name and related logos are registered trademarks of XM Satellite Radio Inc.
2
GETTING STARTED
Supplied accessories
Please check that you received all of the following parts.
Remote control
CODE SET |
TRANSMIT |
|
|
|
|
|
SYSTEM |
POWER |
POWER |
STANDBY |
POWER |
TV |
AV |
|
|
CD |
MD/CD-R |
TUNER |
SLEEP |
DVD |
DTV/CBL |
V-AUX |
MULTI CH IN |
VCR |
|
|
AMP |
TV VOL |
TV CH |
VOLUME |
|
TV MUTE |
TV INPUT |
|
|
|
|
MUTE |
|
STEREO |
MUSIC |
ENTERTAIN |
MOVIE |
1 |
2 |
3 |
4 |
STANDARD |
SELECT |
EXTD SUR. |
DIRECT ST. |
5 |
6 |
7 |
8 |
A SPEAKERS B |
NIGHT |
STRAIGHT |
|
9 |
0 |
10 |
ENT. |
|
|
|
EFFECT |
LEVEL |
PRESET/CH |
SET MENU |
|
TITLE |
|
|
MENU |
BAND |
|
|
SRCH MODE |
|
ENTER |
|
|
A-E/CAT. |
A-E/CAT. |
||
RETURN |
|
|
DISPLAY |
MEMORY |
|
|
|
REC |
|
|
|
AUDIO
DISC SKIP
Batteries (4) |
AM loop antenna |
75-ohm/300-ohm antenna |
||||||
(AAA, R03, UM-4) |
|
adapter (U.K. model only) |
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Indoor FM antenna |
Indoor FM antenna |
(U.S.A., Canada and China |
(U.K., Europe, Australia |
models) |
and Korea models) |
INTRODUCTION
Installing batteries in the remote control
2 1
3
1Press the part and slide the battery compartment cover off.
2Insert four supplied batteries (AAA, R03, UM-4) according to the polarity markings (+ / –) on the inside of the battery compartment.
3Slide the cover back until it snaps into place.
Notes on batteries
•Change all of the batteries if you notice the following conditions; the operation range of the remote control decreases, the indicator does not flash or its light becomes dim.
•Do not use old batteries together with new ones.
•Do not use different types of batteries (such as alkaline and manganese batteries) together. Read the packaging carefully as these different types of batteries may have the same shape and color.
•If the batteries have leaked, dispose of them immediately. Avoid touching the leaked material or letting it come into contact with clothing, etc. Clean the battery compartment thoroughly before installing new batteries.
•Do not throw away batteries with general house waste; dispose of them correctly in accordance with your local regulations.
If the remote control is without batteries for more than 2 minutes, or if exhausted batteries remain in the remote control, the contents of the memory may be cleared. When the memory is cleared, insert new batteries, set up the remote control code and program any acquired functions that may have been cleared.
3
CONTROLS AND FUNCTIONS
Front panel
1 |
2 |
3 4 5 |
6 |
7 |
8 |
9 |
0 |
A |
(U.S.A. model)
|
|
|
|
|
|
|
|
|
VOLUME |
STANDBY |
|
|
|
|
|
|
|
|
|
/ON |
|
|
|
|
|
|
|
|
|
|
|
|
PRESET/TUNING |
FM/AM |
A/B/C/D/E |
l PRESET/TUNING/CH h |
MEMORY |
TUNING MODE |
|
|
|
|
SEARCH MODE |
XM |
CATEGORY |
|
|
DISPLAY |
|
|
|
|
EDIT |
|
NEXT |
LEVEL |
MAN'L/AUTO FM |
AUTO/MAN'L MONO |
|
|
|
|
|
|
|
|
INPUT |
|
|
PHONES |
SPEAKERS |
STRAIGHT |
l |
PROGRAM h |
|
|
|
VIDEO AUX |
|
|
A |
B |
|
|
|
INPUT MODE |
|
MULTI CH |
|
|
|
|
|
|
|
|
|
INPUT |
|
|
|
|
EFFECT |
|
|
|
|
|
|
|
|
|
TONE CONTROL |
BASS/TREBLE |
|
|
|
|
|
SILENT CINEMA |
|
|
|
|
|
|
|
VIDEO |
L AUDIO R |
B C D E F G
1 STANDBY/ON
Turns on this unit or sets it to the standby mode. When you turn on this unit, you will hear a click and there will be a 4 to 5-second delay before this unit can reproduce sound.
Note
In standby mode, this unit consumes a small amount of power in order to receive infrared-signals from the remote control.
2 Remote control sensor
Receives signals from the remote control.
3 Front panel display
Shows information about the operational status of this unit.
4PRESET/TUNING (EDIT), SEARCH MODE*
Switches the function of PRESET/TUNING/ CH* l/ h, LEVEL –/+ between selecting preset station numbers and tuning.
5FM/AM, XM*
Switches the reception band when the unit is in tuner mode.
H I J
6 A/B/C/D/E, NEXT, CATEGORY*
Selects one of the 5 preset station groups (A to E) when the unit is in tuner mode.
Selects the speaker channel to be adjusted when the unit is not in tuner mode.
7PRESET/TUNING/ CH* l / h, LEVEL –/+
Selects preset station number 1 to 8 when the colon (:) is displayed next to the band indication in the front panel display when the unit is in tuner mode. Selects the tuning frequency when the colon (:) is not displayed.
Adjusts the level of the speaker channel selected using A/B/C/D/E (NEXT) when the unit is not in tuner mode.
8MEMORY (MAN’L/AUTO FM)
Stores a station in the memory. Hold down this button for more than 3 seconds to start automatic preset tuning.
9 TUNING MODE (AUTO/MAN’L MONO), DISPLAY*
Switches between automatic tuning (AUTO indicator on) and manual tuning (AUTO indicator off).
4
0 VIDEO AUX jacks
Input audio and video signals from a portable external source such as a game console. To reproduce source signals from these jacks, select V-AUX as the input source.
A VOLUME
Controls the output level of all audio channels. This does not affect the REC OUT level.
B PHONES (SILENT CINEMA) jack
Outputs audio signals for private listening with headphones. When you connect headphones, no signals are output to the OUTPUT jacks or to the speakers.
All Dolby Digital and DTS audio signals are mixed down to the left and right headphone channels.
CSPEAKERS A/B
Turns on or off the set of front speakers connected to the A and/or B terminals on the rear panel each time the corresponding button is pressed.
D STRAIGHT (EFFECT)
Switches the sound fields off or on. When STRAIGHT is selected, input signals (2-channel or multi-channel) are output directly from their respective speakers without effect processing.
E TONE CONTROL
Use to adjust the bass/treble balance for the front left and right speakers (see page 27).
F BASS/TREBLE –/+
Use to adjust the bass/treble balance for the front left and right speakers (in conjunction with TONE CONTROL).
G PROGRAM l / h
Use to select sound field programs (see page 27).
H INPUT MODE
Sets the priority (AUTO, DTS, ANALOG) for the type of signals received when one component is connected to two or more of this unit’s input jacks (see page 32).
I INPUT selector
Selects the input source you want to listen to or watch.
J MULTI CH INPUT
Selects the source connected to the MULTI CH INPUT jacks. When selected, the MULTI CH INPUT source takes priority over the source selected with INPUT (or the input selector buttons on the remote control).
*Available only when the unit is in the XM Satellite Radio mode (see page 41).
CONTROLS AND FUNCTIONS
INTRODUCTION
5
CONTROLS AND FUNCTIONS
Remote control
This section describes the function of each control on the remote control used to control this unit. To operate other components, see “REMOTE CONTROL FEATURES” on page 65.
1 |
|
|
|
|
0 |
2 |
CODE SET |
TRANSMIT |
|
A |
|
|
|
|
SYSTEM |
||
|
POWER |
POWER |
STANDBY |
POWER |
|
|
TV |
AV |
|
|
B |
|
CD |
MD/CD-R |
TUNER |
SLEEP |
|
|
|
|
|
|
C |
|
DVD |
DTV/CBL |
V-AUX |
MULTI CH IN |
|
3 |
|
|
|
|
D |
|
VCR |
|
|
AMP |
|
|
|
|
|
|
E |
|
|
|
|
|
F |
|
TV VOL |
TV CH |
VOLUME |
|
|
|
TV MUTE |
TV INPUT |
|
|
G |
|
|
|
MUTE |
||
|
STEREO |
MUSIC |
ENTERTAIN |
MOVIE |
|
4 |
1 |
2 |
3 |
4 |
|
STANDARD |
SELECT |
EXTD SUR. |
DIRECT ST. |
|
|
|
|
||||
|
5 |
6 |
7 |
8 |
|
5 |
A SPEAKERS B |
NIGHT |
STRAIGHT |
H |
|
|
9 |
0 |
10 |
ENT. |
|
6 |
|
||||
|
|
|
EFFECT |
|
|
|
LEVEL |
PRESET/CH |
SET MENU |
|
|
7 |
|
|
I |
||
TITLE |
|
|
MENU |
||
8 |
BAND |
|
|
SRCH MODE |
|
|
ENTER |
|
|
||
9 |
A-E/CAT. |
A-E/CAT. |
|
||
RETURN |
|
|
DISPLAY |
|
MEMORY
REC
AUDIO
DISC SKIP
RAV251
WC55290 EU
1 Infrared window
Outputs infrared control signals. Aim this window at the component you want to operate.
2 CODE SET
Use to set up remote control codes (see page 66).
3 Input selector buttons
Select the input source and change the control area.
4Sound field program/numeric buttons
Use to select sound field programs.
Use numbers 1 through 8 to select preset stations when the unit is in tuner mode.
Use SELECT to playback 2-channel sources in surround (see page 30).
Use EXTD SUR. to switch between 5.1 or 6.1-channel playback of multi-channel software (see page 29).
Use DIRECT ST. to playback 2-channel sources in high fidelity sound (see page 31).
5SPEAKERS A/B
Use to turn on or off the set of front speakers connected to the A and/or B terminals on the rear panel each time the corresponding button is pressed.
6 NIGHT
Turns on or off the night listening modes (see page 31).
7 LEVEL, BAND
Selects the speaker channel to be adjusted and sets the level.
Switches the reception band when the unit is in tuner mode.
8 Cursor buttons u/ d / j / i /ENTER
Use to select and adjust sound field program parameters or SET MENU items.
Press j/ ito select a preset station group (A to E) when the unit is in tuner mode.
Press u/ dto select a preset station number (1 to 8) when the unit is in tuner mode.
9 RETURN, MEMORY*
Returns to the previous menu level when adjusting the SET MENU parameters.
0 TRANSMIT indicator
Flashes while the remote control is sending signals.
6
A STANDBY
Sets this unit in the standby mode.
B SYSTEM POWER
Turns on the power of this unit.
C SLEEP
Sets the sleep timer.
D MULTI CH IN
Selects multi-channel input when using an external decoder (etc.).
E AMP
Selects the AMP mode. You must select the AMP mode to control the main unit.
F VOLUME +/–
Increases or decreases the volume level.
G MUTE
Mutes the sound. Press again to restore the audio output to the previous volume level.
H STRAIGHT (EFFECT), ENT.*
Switches the sound fields off or on. When STRAIGHT is selected, input signals (2-channel or multi-channel) are output directly from their respective speakers without effect processing.
I SET MENU, SRCH MODE*
Activates the SET MENU function.
Selects preset station groups when the unit is in tuner mode.
*Available only when the unit is in the XM Satellite Radio mode (see page 41).
CONTROLS AND FUNCTIONS
Using the remote control
The remote control transmits a directional infrared beam. Be sure to aim the remote control directly at the remote control sensor on the main unit during operation.
30 |
30 |
Approximately 6 m (20 ft) |
|
■ Handling the remote control
•Do not spill water or other liquids on the remote control.
•Do not drop the remote control.
•Do not leave or store the remote control in the following types of conditions:
–places of high humidity, such as near a bath
–places of high temperature, such as near a heater or stove
–extremely low temperatures
–dusty places
INTRODUCTION
7
CONTROLS AND FUNCTIONS
Front panel display
1 |
|
2 |
3 4 5 |
|
6 |
7 |
8 90 |
A B |
|
|||
t |
96 |
|
VCR |
V-AUX |
DTV/CBL |
DVD |
MD/CD-R |
TUNER |
CD |
|
|
|
|
24 |
VIRTUAL SILENT CINEMA |
|
|
|
YPAO HD AUTO TUNED STEREO MEMORY |
MUTE VOLUME |
|||||
MATRIX DISCRETE |
SP |
|
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|||
qDIGITAL |
|
|
HiFi DSP |
|
|
|
|
|
|
|||
STANDARD ZONE2 NIGHT |
A B |
XM PTY HOLD PS PTY RT CT EON SLEEP |
|
|
dB |
|||||||
q EX |
q PL |
|
|
|||||||||
|
|
|
|
|
|
|
ft |
96/24 |
|
|||
|
|
|
|
|
|
|
|
|
||||
q PL qPL x |
|
|
|
|
|
|
|
L C R |
||||
|
|
|
|
|
|
|
mS |
DUAL |
||||
PCM |
|
|
|
|
|
|
|
|
LFE |
SL SB |
SR |
|
|
|
|
|
|
|
|
|
dB |
||||
|
|
|
|
|
|
|
|
|
|
|
||
C |
|
D |
E F G |
H I |
|
|
J KL M |
|
1 Decoder indicators
When any of this unit’s decoders function, the respective indicator lights up.
2 VIRTUAL indicator
Lights up when Virtual CINEMA DSP is active (see page 32).
3 SILENT CINEMA indicator
Lights up when headphones are connected and a sound field program is selected (see page 27).
4 Input source indicators
A cursor lights to show the current input source.
5 Sound field indicators
Light to indicate the active DSP sound fields.
Presence DSP sound field
|
Listening position |
Left surround |
Right surround |
DSP sound field |
DSP sound field |
Surround back DSP sound field
6 CINEMA DSP indicator
Lights up when you select a CINEMA DSP sound field program.
7 AUTO indicator
Lights up to indicate that automatic tuning is possible.
8 TUNED indicator
Lights up when this unit is tuned into a station.
9 STEREO indicator
Lights up when this unit is receiving a strong signal for an FM stereo broadcast while the AUTO indicator is lit.
0 MEMORY indicator
Flashes to show that a station can be stored.
A MUTE indicator
Flashes while the MUTE function is on.
BVOLUME level indication
Indicates the current volume level.
CPCM indicator
Lights up when this unit is reproducing PCM (Pulse Code Modulation) digital audio signals.
D STANDARD indicator
Lights up when Surround Standard or Surround Enhanced is selected (see page 30).
E NIGHT indicator
Lights up when you select night listening mode.
F SP A B indicators
Light up according to the set of front speakers selected. Both indicators light up when both sets of speakers are selected.
G Headphones indicator
Lights up when headphones are connected.
H HiFi DSP indicator
Lights up when you select a HiFi DSP sound field program.
I Multi-information display
Shows the current sound field program name and other information when adjusting or changing settings.
J SLEEP indicator
Lights up while the sleep timer is on.
8
K 96/24 indicator
Lights up when a DTS 96/24 signal is input to this unit.
L LFE indicator
Lights up when the input signal contains the LFE signal.
M Input channel indicators/speaker indicators
Indicate the channel components of the current digital input signal.
Indicate the number of speakers connected in SPEAKERS (page 24), or indicate the channel being adjusted in
SP LEVEL (page 59).
CONTROLS AND FUNCTIONS
INTRODUCTION
9
CONTROLS AND FUNCTIONS
Rear panel
1 2 |
3 |
|
|
4 |
|
|
|
5 |
|
|
|
6 |
7 |
||
|
|
|
|
|
|
|
|
|
|
TUNER |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
75Ω UNBAL. |
|
|
|
|
|
|
|
SYSTEM CONNECTOR |
|
|
COMPONENT VIDEO |
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
PR |
PB |
Y |
|
|
|
|
|
|
|
|
|
|
|
|
|
DVD |
|
|
FM |
|
AM |
|
|
|
|
|
MULTI CH INPUT |
|
|
AUDIO |
|
VIDEO |
|
|
|
|
|
|
|
||
|
|
|
|
|
|
ANT |
GND |
ANT |
|
|
XM |
|
|||
DIGITAL |
R |
L |
R |
L |
VIDEO |
S VIDEO |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
DTV/ |
|
|
|
|
|
|
|
|
|
|
OUTPUT |
|
|
|
|
|
CBL |
|
|
|
|
|
|
|
|
|
MD/CD-R |
FRONT |
|
|
|
DVD |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
AC OUTLETS |
|
|
|
|
|
|
MONITOR |
|
|
|
|
|
|
|
|
SWITCHED |
OPTICAL |
|
|
|
|
DTV/ |
OUT |
|
|
|
|
|
|
|
|
|
SURROUND |
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
CBL |
|
|
|
|
|
|
|
|
|
|
|
SUB |
CENTER |
|
|
|
|
|
|
|
|
|
|
|
|
|
MD/CD-R |
WOOFER |
|
|
|
IN |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
VCR |
|
|
|
|
|
|
|
|
|
|
DVD |
|
|
|
|
|
|
|
|
FRONT |
L |
SPEAKERS |
|
L |
|
|
CD |
|
|
|
OUT |
|
+ |
R |
+ |
R |
SURROUND |
+ |
||||
|
|
|
|
|
|
|
|
– – |
|
+ |
– – |
|
|||
DTV/CBL |
IN |
|
|
|
|
|
A |
|
|
|
|
|
|
|
|
|
(PLAY) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
MD/ |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CD-R |
|
|
|
VIDEO |
S VIDEO |
|
|
|
|
|
|
|
|
|
|
OUT |
|
|
SUB |
|
|
|
|
|
|
|
|
|
|
|
CD |
(REC) |
|
|
WOOFER |
MONITOR OUT |
B |
|
|
|
|
|
|
|
|
|
COAXIAL |
R |
L |
|
|
|
|
|
|
|
|
|
|
|
|
|
DIGITAL |
|
|
|
|
+ |
|
– – |
|
+ |
+ |
– – |
|
+ |
||
INPUT |
AUDIO |
|
|
OUTPUT |
|
|
|
|
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
CENTER |
SURROUND BACK |
|
8 9 0
1DIGITAL OUTPUT jack (HTR-5850 only)
See page 19 for connection information.
2MULTI CH INPUT jacks
See page 17 for connection information.
3SYSTEM CONNECTOR jack
(HTR-5850: U.S.A. and Canada models only)
Use to connect a YAMAHA subwoofer equipped with a SYSTEM CONNECTOR jack to this unit (see page 13).
4 Video component jacks
See pages 16 and 18 for connection information.
5 Antenna terminals
See page 20 for connection information.
6 XM jack
See page 40 for connection information.
(HTR-5850 U.S.A. model)
A
7 AC OUTLET(S)
Use to supply power to your other A/V components (see page 21).
8DIGITAL INPUT jacks
(MD/CD-R jack is for HTR-5850 only)
See pages 16, 18 and 19 for details.
9 Audio component jacks
See page 19 for connection information.
0 SUBWOOFER OUTPUT jack
See page 13 for connection information.
A Speaker terminals
See page 13 for connection information.
10
SPEAKER SETUP
Speaker placement
The speaker layout below shows the standard ITU-R* speaker setting. You can use it to enjoy CINEMA DSP and multi-channel audio sources.
*ITU-R is the radio communication sector of the ITU (International Telecommunication Union).
FL |
C |
FR |
30˚
SL |
|
SR |
|
|
60˚ |
SL |
80˚ |
SR |
|
|
SB |
Surround speakers (SR and SL)
The surround speakers are used for effect and surround sounds. Place these speakers behind your listening position, facing slightly inwards, about 1.8 m (6 ft) above the floor.
Surround back speaker (SB)
The surround back speaker supplements the surround speakers and provides for more realistic front-to-back transitions. Place this speaker directly behind the listening position and at the same height as the surround speakers.
Subwoofer
The use of a subwoofer, such as the YAMAHA Active Servo Processing Subwoofer System, is effective not only for reinforcing bass frequencies from any or all channels, but also for high fidelity reproduction of the LFE (lowfrequency effect) channel included in Dolby Digital and DTS software. The position of the subwoofer is not so critical, because low bass sounds are not highly directional. But it is better to place the subwoofer near the front speakers. Turn it slightly toward the center of the room to reduce wall reflections.
1.8 m (6 ft)
PREPARATION
Front speakers (FR and FL)
The front speakers are used for the main source sound plus effect sounds. Place these speakers an equal distance from the ideal listening position. The distance of each speaker from each side of the video monitor should be the same.
Center speaker (C)
The center speaker is for the center channel sounds (dialog, vocals, etc.). If for some reason it is not practical to use a center speaker, you can do without it. Best results, however, are obtained with the full system. Align the front face of the center speaker with the front face of your video monitor. Place the speaker centrally between the front speakers and as close to the monitor as possible, such as directly over or under it.
11
SPEAKER SETUP
Speaker connections
Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be unnatural and lack bass.
CAUTION
•If you will use 4 or 6 ohm speakers, be sure to set this unit’s speaker impedance setting to 4 ohms before using (see page 21).
•Before connecting the speakers, make sure that the power of this unit is off.
•Do not let the bare speaker wires touch each other or do not let them touch any metal part of this unit. This could damage this unit and/or speakers.
•Use magnetically shielded speakers. If this type of speakers still creates the interference with the monitor, place the speakers away from the monitor.
A speaker cord is actually a pair of insulated cables running side by side. One cable is colored or shaped differently, perhaps with a stripe, groove or ridges.
Connect the striped (grooved, etc.) cable to the “+” (red) terminals on this unit and your speaker. Connect the plain cable to the “–” (black) terminals.
10 mm (3/8")
1 2
1Remove approximately 10 mm (3/8") of insulation from the end of each speaker cable.
2Twist the exposed wires of the cable together to prevent short circuits.
3Unscrew the knob.
4Insert one bare wire into the hole in the side of each terminal.
5 Tighten the knob to secure the wire.
3 4
5
Red: positive (+) Black: negative (–)
■ Banana plug connections
(With the exception of U.K. and Europe models) First, tighten the knob and then insert the banana plug connector into the end of the corresponding terminal.
Banana plug
(With the exception of U.K. and Europe models)
12
SPEAKER SETUP
Subwoofer |
Front speakers (A) |
|
|
|
system |
Right |
Left |
|
|
|
|
Surround speakers |
||
1 |
|
Right |
|
Left |
|
|
|
|
|
|
2 |
3 |
6 |
7 |
(HTR-5850 U.S.A. model)
SYSTEM CONNECTOR
|
|
|
FRONT |
|
SPEAKERS |
SURROUND |
|
|
||
|
+ |
R |
L |
|
R |
L |
+ |
|||
|
|
– – |
|
+ |
+ |
– – |
|
|
||
|
A |
|
|
|
|
|
|
|
|
|
SUB |
|
|
|
|
|
|
|
|
|
|
WOOFER |
B |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
OUTPUT |
+ |
|
– – |
|
+ |
+ |
– – |
|
|
+ |
|
|
|
|
|
|
CENTER |
|
SURROUND BACK |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
4 |
|
|
|
|
|
|
|
|
|
|
|
|
|
5 |
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|||||||||
|
|
|
Front |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
speakers |
Center |
|
|
|
|
|
|
|
|
|
|
||||||
|
|
|
(B) |
speaker |
|
|
|
|
|
|
|
|
|
|
||||||
|
|
|
Surround back |
|||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
speaker
■ FRONT terminals
Connect one or two speaker systems (2, 3) to these terminals. If you use only one speaker system, connect it to the FRONT A or B terminals.
■ CENTER terminals
Connect a center speaker (4) to these terminals.
■ SURROUND terminals
Connect surround speakers (6, 7) to these terminals.
■ SUBWOOFER jack
Connect a subwoofer with built-in amplifier (1), such as the YAMAHA Active Servo Processing Subwoofer System, to this jack.
■SYSTEM CONNECTOR jack (HTR-5850: U.S.A. and Canada models
only)
Use this jack to control the power of your Yamaha subwoofer if a system connector jack is available on the subwoofer.
■ SURROUND BACK terminals
Connect a surround back speaker (5) to these terminals.
2
4
3 |
1 |
6 |
|
||
|
|
|
|
7 |
5 |
|
|
|
|
Speaker layout |
|
PREPARATION
13
CONNECTIONS
Before connecting components
CAUTION
Do not connect this unit or other components to the mains power until all connections between components are complete.
■ Cable indications
For analog signals |
|
left analog cables |
L |
right analog cables |
R |
For digital signals |
|
optical cables |
O |
coaxial cables |
C |
For video signals |
|
video cables |
V |
S-video cables |
S |
|
PR |
component video cables |
PB |
|
Y |
■ Analog jacks
You can input analog signals from audio components by connecting audio pin cable to the analog jacks on this unit. Connect red plugs to the right jacks and white plugs to the left jacks.
■ Digital jacks
This unit has digital jacks for direct transmission of digital signals through either coaxial or fiber optic cables. You can use the digital jacks to input PCM, Dolby Digital and DTS bitstreams. When you connect components to both the COAXIAL and OPTICAL jacks, priority is given to the input signals from the COAXIAL jack. All digital input jacks are compatible with 96-kHz sampling digital signals.
Note
This unit handles digital and analog signals independently. Thus audio signals input to the analog jacks are only output to the analog OUT (REC) jacks.
Dust protection cap
Pull out the cap from the optical jack before you connect the fiber optic cable. Do not discard the cap. When you are not using the optical jack, be sure to put the cap back in place. This cap protects the jack from dust.
14
■ Video jacks
This unit has three types of video jacks. Connection depends on the availability of input jacks on your monitor.
[HTR-5850 only]
The signals input through the S VIDEO jacks on HTR5850 are automatically converted for output through the VIDEO jacks. When V. CONV. is set to ON (see page 59), signals input through the VIDEO jacks can be output through the S VIDEO jacks.
COMPONENT VIDEO
VIDEO |
S VIDEO |
PR |
PB |
Y |
|
VIDEO jacks
For conventional composite video signals.
S VIDEO jacks
For S-video signals, separated into luminance (Y) and color (C) video signals to achieve high-quality color reproduction.
COMPONENT VIDEO jacks
For component signals, separated into luminance (Y) and color difference (PB, PR) to provide the best quality in picture reproduction.
Signal flow inside HTR-5850 |
|
Input |
Output |
(MONITOR OUT) |
|
COMPONENT |
|
VIDEO |
|
S VIDEO |
|
VIDEO
Only when V. CONV. is set to ON (see page 61).
Signal flow inside HTR-5840 |
|
Input |
Output |
(MONITOR OUT) |
|
COMPONENT |
|
VIDEO |
|
S VIDEO |
|
VIDEO |
|
Note
[HTR-5850 only]
When signals are input through both the S VIDEO and VIDEO jacks, signals input through the S VIDEO jack have priority.
CONNECTIONS
PREPARATION
15
CONNECTIONS
Connecting video components
■ Connections for DVD playback
Note
For HTR-5840, be sure to connect your video source components in the same way you connect your video monitor to HTR-5840. For HTR-5850, be sure to connect your video source components in the same way you connect your video monitor to HTR-5850 if VIDEO CONV. (see page 59) is set to OFF. (Even when V.CONV is set to OFF, S-video signals input from your video source component are automatically converted to composite signals in this unit.)
For example, if you connect your video monitor to this unit using a VIDEO connection, connect your video source components to this unit using the VIDEO connections.
|
Coaxial out |
|
Video out |
|
|
|
|
|
Optical out |
DVD player |
|
|
|
|
|
|
Audio out |
|
|
|
|
|
|
C |
O |
R L |
V |
S |
PR |
PB |
Y |
|
|
|
|
|
|
|
COMPONENT VIDEO
PR PB Y
DVD
AUDIO |
VIDEO |
VIDEO |
S VIDEO |
|
MONITOR |
|
OUT |
DVD |
|
Video in |
Video |
|
monitor |
DVD
DVD |
|
|
COAXIAL |
VIDEO |
S VIDEO |
|
||
DIGITAL |
MONITOR OUT |
|
INPUT |
|
|
(HTR-5850 U.S.A. model)
16
CONNECTIONS
■ Connecting to the MULTI CH INPUT jacks
This unit is equipped with 6 additional input jacks (left and right FRONT, CENTER, left and right SURROUND and SUBWOOFER) for discrete multi-channel input from a multi-format player, external decoder, sound processor or preamplifier.
Connect the output jacks on your multi-format player or external decoder to the MULTI CH INPUT jacks. Be sure to match the left and right outputs to the left and right input jacks for the front and surround channels.
(HTR-5850 U.S.A. model)
MULTI CH INPUT
R |
L |
FRONT |
|
SURROUND |
|
SUB |
CENTER |
WOOFER |
|
R L |
Subwoofer |
R L |
|
out |
|||
|
|
||
|
Center |
|
|
|
out |
|
|
|
Multi-format player/ |
|
|
|
External decoder |
|
|
Front |
|
Surround |
|
out |
|
out |
Notes
•When you select MULTI CH INPUT as the input source, this unit automatically turns off the digital sound field processor, and you cannot select sound field programs.
•This unit does not redirect signals input to the MULTI CH INPUT jacks to accommodate for missing speakers. We recommend that you connect at least a 5.1-channel speaker system before using this feature.
•When headphones are used, only front left and right channels are output.
PREPARATION
17
CONNECTIONS
■ Connections for other video components
Notes
•For HTR-5840, be sure to connect your video source components in the same way you connect your video monitor to HTR-5840. For HTR-5850, be sure to connect your video source components in the same way you connect your video monitor to HTR-5850 if VIDEO CONV. (see page 59) is set to OFF. (Even when V.CONV is set to OFF, S-video signals input from your video source component are automatically converted to composite signals in this unit.)
For example, if you connect your video monitor to this unit using a VIDEO connection, connect your video source components to this unit using the VIDEO connections.
•Converted video signals are only output to the MONITOR OUT jacks. When recording you must make the same type of video connections (i.e., S-video) between each component.
|
|
|
Video out |
|
|
|
|
|
Optical out |
Cable TV or |
|
|
|
|
|
|
|
|
satellite tuner |
|
|
|
|
|
|
|
Audio out |
|
|
|
|
|
|
|
|
O |
R L |
|
V |
S |
|
PR |
PB |
Y |
|
|
|
|
|
||||
|
|
|
|
COMPONENT VIDEO |
|
|
|
|
|
|
|
|
PR |
PB |
Y |
|
|
MULTI CH INPUT |
|
AUDIO |
VIDEO |
|
|
|
|
|
|
R |
L |
VIDEO |
S VIDEO |
|
|
|
|
|
|
|
|
DTV/ |
|
|
|
|
|
|
|
|
CBL |
|
|
|
|
MONITOR
OUT
DTV/
CBL
IN
VCR
OUT
DTV/CBL
VIDEO |
S VIDEO |
MONITOR OUT
DIGITAL
INPUT
Video in |
Video |
|
monitor |
(HTR-5850 U.S.A. model)
R L R L |
|
V |
or S |
V or S |
|
|
|
|
|
Audio in |
DVD recorder |
Video in |
|
|
Audio out |
or VCR |
Video out |
||
|
||||
■ VIDEO AUX jacks (on the front panel) |
|
VIDEO AUX |
|
|
|
|
|
||
Use these jacks to connect any video source, such as a |
VIDEO |
L AUDIO |
R |
|
game console or video camera, to this unit. |
|
V |
L |
R |
|
|
|
|
Audio out R |
Game |
|
Audio out L |
console or |
|
video camera |
||
|
||
Video out |
|
18
CONNECTIONS
Connecting audio components
■ Connections for audio components
Note
DIGITAL OUTPUT (MD/CD-R) jack and DIGITAL INPUT (MD/CD-R) jack are not equipped with HTR-5840. To connect a MD recorder or tape deck to HTR-5840, use the analog connections (AUDIO OUT/IN).
(HTR-5850 U.S.A. model)
DIGITAL
OUTPUT
MD/CD-R
Audio out |
MD/CD-R |
|
|
L |
|
CD player |
|
R |
CD |
|
Coaxial out |
|
IN |
|
|
(PLAY) |
|
|
C |
|
MD/ |
|
|
CD-R |
|
|
|
|
OUT |
|
|
CD |
(REC) |
|
|
COAXIAL |
R |
L |
|
DIGITAL |
||
|
INPUT |
|
|
|
|
|
O |
O |
|
|
|
||
|
|
|
R L |
R |
L |
Audio out |
|
Audio in |
MD recorder or |
Optical out |
|
|
tape deck |
|
|
|
Optical in |
PREPARATION
19
CONNECTIONS
Connecting the FM and AM antennas
Both FM and AM indoor antennas are included with this unit. In general, these antennas should provide sufficient signal strength. Connect each antenna correctly to the designated terminals.
Indoor FM antenna (included)
AM loop antenna (included)
|
TUNER |
|
75Ω UNBAL. |
|
|
FM |
GND |
AM |
ANT |
ANT |
(HTR-5850 U.S.A. model)
Ground (GND terminal)
For maximum safety and minimum interference, connect the antenna GND terminal to a good earth ground. A good earth ground is a metal stake driven into moist earth.
■ Connecting the AM loop antenna
1Set up the AM loop antenna, then connect it to the terminals on this unit.
2 Press and hold the tab to insert the AM loop antenna lead wires into the AM ANT and GND terminals.
3Orient the AM loop antenna for the best reception.
Notes
•The AM loop antenna should be placed away from this unit.
•The AM loop antenna should always be connected, even if an outdoor AM antenna is connected to this unit.
•A properly installed outdoor antenna provides clearer reception than an indoor one. If you experience poor reception quality, an outdoor antenna may improve the quality. Consult the nearest authorized YAMAHA dealer or service center about outdoor antennas.
20
Connecting the power supply cord
■Connecting the AC power cord
Plug the power cord into an AC wall outlet.
■AC OUTLET(S) (SWITCHED)
U.K. and Australia models |
..................................... 1 outlet |
Korea model............................................................... |
None |
Other models......................................................... |
2 outlets |
Use these outlets to connect the power cords from your other components to this unit. Power to the AC OUTLET(S) is controlled by this unit’s STANDBY/ON (or SYSTEM POWER and STANDBY). The outlet(s) supply power to any connected component whenever this unit is turned on. For information on the maximum power (total power consumption of components), see “SPECIFICATIONS” on page 81.
■ Memory back-up
The memory back-up circuit prevents the stored data from being lost even if this unit is in the standby mode. However if the power cord is disconnected from the AC wall outlet, or the power supply is cut for more than one week, the stored data will be lost.
CONNECTIONS
Speaker impedance setting
CAUTION
If you are using 4 or 6 ohm speakers, set the impedance to 4 or 6 ohms as follows before turning on the power.
Be sure this unit is in the standby mode.
1Turn off the power to this unit, and while holding down STRAIGHT (EFFECT), press STANDBY/ON.
This unit turns on, and the ADVANCED SETUP menu appears in the front panel display.
STRAIGHT |
While holding |
|
|
STANDBY |
|
EFFECT |
down, press |
/ON |
|
2Press PROGRAM l/ hto move through the menu and select “SP IMP.”.
l PROGRAM h
3Press STRAIGHT (EFFECT) repeatedly to select “4Ω MIN”.
STRAIGHT
EFFECT
4 Press STANDBY/ON to turn off the power.
STANDBY /ON
The setting you made is reflected the next time this unit’s power is turned on.
PREPARATION
21
CONNECTIONS
Turning on the power
When all connections are complete, turn on the power of this unit.
(U.S.A. model)
|
|
|
|
|
|
|
|
VOLUME |
STANDBY |
|
|
|
|
|
|
|
|
/ON |
|
|
|
|
|
|
|
|
|
|
|
PRESET/TUNING |
FM/AM |
A/B/C/D/E |
l PRESET/TUNING/CH h |
MEMORY |
TUNING MODE |
|
|
|
|
XM |
|
|
|
|
|
|
|
|
|
|
|
INPUT |
|
PHONES |
SPEAKERS |
STRAIGHT |
l |
PROGRAM h |
|
|
VIDEO AUX |
|
|
A |
B |
|
|
|
INPUT MODE |
|
MULTI CH |
|
|
|
|
|
|
|
|
INPUT |
|
|
|
TONE CONTROL |
BASS/TREBLE |
|
|
|
SILENT CINEMA
VIDEO |
L AUDIO R |
STANDBY/ON
CODE SET |
TRANSMIT |
|
|
|
|
|
SYSTEM |
POWER |
POWER |
STANDBY |
POWER |
TV |
AV |
|
SYSTEM POWER |
CD |
MD/CD-R |
TUNER |
SLEEP |
DVD |
DTV/CBL |
V-AUX |
MULTI CH IN |
VCR |
|
|
AMP |
TV VOL |
TV CH |
VOLUME |
|
TV MUTE |
TV INPUT |
|
|
Press STANDBY/ON (or SYSTEM POWER on the remote control) to turn on the power of this unit.
SYSTEM
POWER
STANDBY /ON
or
Front panel |
Remote control |
22
BASIC SETUP
The basic setup feature is a useful way to set up your system quickly and with minimal effort.
y
•If you wish to configure the unit manually using more precise adjustments, use the detailed parameters in SOUND MENU (page 58) instead of using BASIC SETUP.
•Altering any parameters in BASIC SETUP will reset all parameters in SOUND MENU.
•Initial settings are indicated in bold for each parameter.
Using the BASIC SETUP menu
Before you begin:
•Press SPEAKERS A or B on the front panel (or press AMP to select the AMP mode, then press SPEAKERS A or B on the remote control) to select the front speakers you want to use.
•Make sure you disconnect your headphones from this unit.
|
CODE SET |
TRANSMIT |
|
STANDARD |
SELECT |
EXTD SUR. |
DIRECT ST. |
|
|
|
|
|
|
SYSTEM |
5 |
6 |
7 |
8 |
|
|
|
|
|
|
|
|
|
|
|
|
POWER |
POWER |
STANDBY |
POWER |
|
|
|
|
|
|
TV |
AV |
|
|
A SPEAKERS B |
NIGHT |
STRAIGHT |
|
|
|
|
|
9 |
0 |
10 |
ENT. |
|
||
|
|
|
|
|
|
||||
|
CD |
MD/CD-R |
TUNER |
SLEEP |
|
|
|
EFFECT |
2 |
|
|
|
|
|
LEVEL |
PRESET/CH |
SET MENU |
||
1 |
DVD |
DTV/CBL |
V-AUX |
MULTI CH IN |
TITLE |
|
|
MENU |
|
|
|
|
|
BAND |
|
|
SRCH MODE |
||
VCR |
|
|
AMP |
|
ENTER |
|
3-13 |
||
|
|
|
|
|
|
||||
|
|
|
|
A-E/CAT. |
A-E/CAT. |
||||
|
|
|
|
|
RETURN |
|
|
DISPLAY |
|
|
|
|
|
|
MEMORY |
|
|
|
|
|
|
|
|
|
REC |
|
|
|
|
|
|
|
|
|
|
|
|
AUDIO |
|
|
TV VOL |
TV CH |
VOLUME |
DISC SKIP |
|
|
|
|
|
|
TV MUTE |
TV INPUT |
|
|
|
|
|
|
|
1 Press AMP.
AMP
2Press SET MENU.
“BASIC SETUP” appears in the front panel display.
SET MENU |
BASIC SETUP |
SRCH |
|
MENU |
|
3 Press ENTER to enter BASIC SETUP.
PRESET/CH
ENTER
A-E/CAT. A-E/CAT.
The ROOM parameter appears in the front panel display.
4 Press j/ i to select the desired setting.
ROOM: S M >L
Select the size of the room you have installed your speakers in. In general, the room sizes are defined as follows:
[U.S.A. and Canada models] |
|
|
S (small) |
16 x 13ft, 200ft2 (4.8 x 4.0m, 20m2) |
|
M (medium) 20 x 16ft, 300ft2 |
(6.3 x 5.0m, 30m2) |
|
L (large) |
26 x 19ft, 450ft2 |
(7.9 x 5.8m, 45m2) |
[Other models] |
|
|
S (small) |
3.6 x 2.8m, 10m2 |
|
M (medium) 4.8 x 4.0m, 20m2 |
||
L (large) |
6.3 x 5.0m, 30m2 |
5Press d to display the SUBWOOFER parameter.
PRESET/CH
ENTER
A-E/CAT. A-E/CAT.
6 Press j/ i to select the desired setting.
SUBWOOFER YES
YES If you have a subwoofer in your system. NONE If you do not have a subwoofer in your system.
PREPARATION
23
BASIC SETUP
7Press d to display the SPEAKERS parameter.
PRESET/CH
ENTER
A-E/CAT. A-E/CAT.
8Press j / i to select the number of speakers you connected.
SPEAKERS 6spk
Choices Display |
Speakers |
|
|
L C R |
Front L/R |
2spk |
|
|
SL SB SR |
|
|
|
|
|
L C R |
Front L/R, Center |
|
3spk |
|
||
SL SB SR |
|
||
|
|
||
|
L C R |
Front L/R, Surround L/R |
|
4spk |
|
||
SL SB SR |
|
||
|
|
||
|
L C R |
Front L/R, Center, Surround L/R |
|
5spk |
|
||
SL SB SR |
|
||
|
|
||
|
L C R |
Front L/R, Center, Surround L/R, |
|
6spk |
Surround back |
||
SL SB SR |
|||
|
|
9 Press d to display SET/CANCEL.
PRESET/CH
ENTER
A-E/CAT. A-E/CAT.
10 Press j / i to select the desired setting.
>SET CANCEL
SET |
To apply the settings you chose in steps |
|
4 through 8. |
CANCEL |
To cancel the setup without making |
|
any changes. |
11 Press ENTER to confirm your selection.
PRESET/CH
ENTER
A-E/CAT. A-E/CAT.
If you selected SET, you hear a test tone from each speaker in turn. “CHECK:TestTone” appears in the front panel display for a few seconds, then “CHECK OK?”.
CHECK:TestTone
CHECK OK? YES
12 Press j / i to select the desired setting.
CHECK OK? YES
YES To complete the setup process if the test tone levels from each speaker were satisfactory.
NO To proceed to the SP LEVEL speaker level adjustment menu to balance the level of each speaker.
13 Press ENTER to confirm your selection.
PRESET/CH
ENTER
A-E/CAT. A-E/CAT.
If you selected NO in step 12, the front speaker level adjustment display appears in the front panel display.
24