Xerox 016-2046-00, 016-2044-00, 016-2040-00, 016-2047-00, 016-2043-00 User Manual

...
0 (0)
User Guide 77
Specifications
Specifications
Material Safety Data Sheet for ColorStix® 8200 Ink
Sticks
SECTION 1- PRODUCT IDENTIFICATION
Trade NamesXerox Part No.
®
8200 Ink Sticks, Black016-2044-00, 016-2040-00
®
8200 Ink Sticks, Cyan016-2045-00, 016-2041-00
®
8200 Ink Sticks, Magenta 016-2046-00, 016-2042-00
®
8200 Ink Sticks, Yellow016-2047-00, 016-2043-00
Supplies Start-up Kit8200 SS 00, 8200 SS 01
Product Use: XEROX Phaser
®
8200 color printers
SECTION 2 - INFORMATION ON INGREDIENTS
Xerox Phaser
®
ColorStix
®
8200 Inks are a proprietary blend of polyethylene
and fatty amide waxes, resins, and dyes. The specific identity of ingredients is
withheld as a trade secret.
®
8200 solid inks are considered articles under Hazard
Communication regulations. This Material Safety Data Sheet is provided as a
customer service.
SECTION 3 - HAZARDS IDENTIFICATION
ROUTES OF EXPOSURE: Skin
POTENTIAL HEALTH EFFECTS
Immediate Effects: None are known, when used as intended in Phaser
®
8200
Color Printers. See Section 11 for toxicology test information.
Chronic Effects: None are known
SIGNS AND SYMPTOMS OF EXPOSURE: None are known.
MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE: None are known.
SECTION 4 - FIRST AID MEASURES
EYES: Contact unlikely. If particles get into eyes, flush thoroughly with water.
INGESTION: Not applicable
INHALATION: Not applicable
SKIN: Wash skin thoroughly with soap and water
SECTION 5 - FIRE FIGHTING MEASURES
FLASH POINT: > 221 degrees C (>429 degrees F), Pensky-Martens closed
tester
FIRE & EXPLOSION HAZARDS: These inks will burn. During a fire, irritating
and toxic gases may be generated by thermal decomposition or combustion.
EXTINGUISHING MEDIA: All extinguishing agents classified as B and C are
effective, including dry powder(s), carbon dioxide, and halon.
FIRE FIGHTING INSTRUCTIONS: Avoid inhalation of smoke. As in any fire,
78 Phaser® 8200 Color Printer
Specifications
wear self-contained breathing apparatus, pressure demand, MSHA/NIOSH
approved, and full protective gear.
SECTION 6 - ACCIDENTAL RELEASE MEASURES
SPILL OR LEAK: Not applicable
SECTION 7 - HANDLING AND STORAGE
HANDLING: No special precautions, when used as intended.
STORAGE: Avoid high temperatures. Keep ink below 60 degrees C
(140 degrees F)
SECTION 8 - EXPOSURE CONTROL - PERSONAL PROTECTION
EXPOSURE GUIDELINES: None established.
ENGINEERING CONTROLS/PERSONAL PROTECTION: No special personal
protection indicated, when used as intended.
SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES
APPEARANCE/ODOR: Waxy solid. Black, blue, red, or yellow in color/Faint
odor
SOLUBILITY IN WATER: Insoluble
MELTING POINT: Approximately 100 degrees C (212 degrees F)
SPECIFIC GRAVITY (Water = 1): Approximately 1, @ 25 degrees C
(77 degrees F)
SECTION 10 - STABILITY AND REACTIVITY
STABILITY: Stable.
CONDITIONS TO AVOID: Temperatures above 200 degrees C (392 degrees F)
INCOMPATIBILITY WITH OTHER MATERIALS: None
HAZARDOUS POLYMERIZATION: Will not occur
HAZARDOUS DECOMPOSITION PRODUCTS: Material may decompose into
toxic byproducts when heated to temperatures above 200 degrees C
(392 degrees F).
SECTION 11 - TOXICOLOGICAL INFORMATION
TOXICITY: Oral LD
50
>5 g/kg (rats); practically non-toxic
SKIN IRRITATION: Primary Dermal Irritation Index = 0.0; not skin irritants.
CARCINOGENICITY: Components not listed by IARC, NTP, or OSHA.
SECTION 12 - ECOLOGICAL INFORMATION
No known impact
User Guide 79
Specifications
SECTION 13 - DISPOSAL CONSIDERATIONS
This product is not a hazardous waste as specified in 40CFR261. TCLP below
hazardous waste levels set by EPA. State and local waste disposal
requirements, however, may be more restrictive. Manage and dispose of waste
in accordance with all federal, state, and local regulations.
SECTION 14 - TRANSPORT INFORMATION
DOT: Not regulated.
SECTION 15 - REGULATORY INFORMATION
TSCA: This material has been manufactured in compliance with the EPA
Toxic Substances Control Act (TSCA).
RCRA (Resource Conservation and Recovery Act): Not a hazardous waste as
specified in 40CFR261. TCLP below hazardous waste levels set by EPA.
SECTION 16 - OTHER INFORMATION
Original preparation date: 11/27/01
Xerox Corporation
Office Printing Business
Environmental, Health & Safety
P.O. Box 1000
Mail Stop 60-512
Wilsonville, Oregon 97070
Safety Information: 800-828-6571
Health Information: 716-422-2177
Material Safety Data Sheet for Silicone Intermediate
Transfer Layer Fluid
SECTION 1- PRODUCT IDENTIFICATION
Trade Name: Xerox Silicone Intermediate Transfer Layer Fluid, impregnated
into printer's maintenance roller.
Xerox part number 016-1933-00 (replacement standard capacity maintenance
kit)
Xerox part number 016-1932-00 (replacement extended capacity maintenance
kit)
Product Use: Xerox Phaser
®
8200 color printers
SECTION 2 - INFORMATION ON INGREDIENTS
Xerox Silicone Intermediate Transfer Layer Fluid is a proprietary blend of
silicone oils. Specific identities of components, and their percentage
composition, are withheld as a trade secret.
Loading...
+ 6 hidden pages