Electric Built-in Cooktop
PRODUCT MODEL NUMBERS
G7CE3034X, G7CE3055X, G7CE3635X, G7CE3655X, G9CE3065X, G9CE3074X, G9CE3675X, W5CE3024X, W5CE3625A
ELECTRICAL REQUIREMENTS
A 3-wire or 4-wire, single phase, 120/240 volt, 60-Hz., AC only electrical supply is required on a separate, 40-amp circuit fused on both sides of the line. The model/serial number rating plate is located on the metal cabinet underneath the cooktop. See the following illustration.
NOTE: A separate 30-amp circuit fused on both sides of the line can be used for models W5CE3024 and G9CE3065.
A
A. Model/serial number plate
PRODUCT DIMENSIONS
B
A
C
D
E |
F |
|
A.Glass depth - black and white models - 213/4" (55.2 cm) Glass depth - stainless steel models - 221/4" (56.4 cm)
B.Glass width - 30" (76.2 cm) models - 307/8" (78.4 cm) Glass width - 36" (91.4 cm) models - 365/16" (92.3 cm)
C.Frame depth - 201/4" (51.5 cm)
D.Frame width - 30" (76.2 cm) models - 2815/16" (73.5 cm) Frame width - 36" (91.4 cm) models - 347/16" (87.5 cm)
E.Cooktop height - 33/4" (9.6 cm)
F.Cooktop height including conduit (located at rear of cooktop, right side) - 51/4" (13.5 cm)
CABINET DIMENSIONS
IMPORTANT: If installing a range hood or microwave hood combination above the cooktop, follow the range hood or microwave hood combination installation instructions for dimensional clearances above the cooktop surface.
A |
D |
|
C |
B |
|
L E F G
H
I
K J
A.30" (76.2 cm) on 30" models; 36" (91.4 cm) on 36" models
B.Combustible area above countertop (shown by dashed box above)
C.30" (76.2 cm) minimum clearance between top of cooktop platform and bottom of uncovered wood or metal cabinet (24" [61 cm] minimum clearance if bottom of wood or metal cabinet is covered by not less than 1/4" [0.6 cm] flame retardant millboard covered with not less than No. 28 MSG sheet steel, 0.015" [0.04 cm] stainless steel, or 0.024" [0.06 cm] aluminum or 0.020" [0.05 cm] copper)
D.13" (33 cm) recommended upper cabinet depth
E.2" (5.1 cm) on most models; 25/8" (6.7 cm) on model JEC4430B
F.201/2" (52.0 cm) recommended cutout.
Will fit in cutout from 203/8"-209/16" (51.8-52.2 cm).
G.18" (45.7 cm) minimum clearance from upper cabinet to countertop within minimum horizontal clearances to cooktop
H.Junction box or outlet: 7" (17.8 cm) minimum from top of countertop
I.Junction box or outlet: 9" (23.0 cm) maximum from right side of cabinet
J.291/2" (74.9 cm) recommended cutout on 30" (76.2 cm) models. Will fit in cutout from 291/16"-299/16" (73.8-75.1 cm) on 30" (76.2 cm) models.
351/2" (90.2 cm) recommended cutout on 36" (91.4 cm) models. Will fit in cutout from 349/16"-359/16" (87.8-90.3 cm) on 36" (91.4 cm) models.
K.1" (2.5 cm) minimum distance to nearest left and right side combustible surface above cooktop
L.1" (2.5 cm) minimum clearance between back wall and countertop
NOTES: After making the countertop cutout, some installations may require notching down the base cabinet side walls to clear the cooktop base. To avoid this modification, use a base cabinet with sidewalls wider than the cutout.
If cabinet has a drawer, a 51/2" (14.0 cm) depth clearance from the top of the countertop to the top of the drawer (or other obstruction) in base cabinet is required.
Because Whirlpool Corporation includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation |
Ref. W10353374 |
Instructions packed with product. Specifications subject to change without notice. |
02/20/2017 |