VTech DECT 6.0 LS6215, DECT 6.0 LS6215-3, DECT 6.0 LS6215-2 User Manual

Size:
1.02 Mb
Download

User’s manual

Accessory handset for use with VTech models

LS6215/LS6215-2/LS6215-3/LS6225/LS6225-2/LS6225-3/LS6225-4/LS6225-5/LS6226-2

w w w.v t e c h p h o n e s . c o m

Model: LS6205

Congratulations

on purchasing your new VTech product. Before using this telephone, please read the Important safety instructions on page 7 of this manual.

This manual has instructions for setup and registration of your new handset. For full instructions on using the handset, see the user’s manual that came with your telephone base.

If you cannot find your user’s manual, you can view or download it at www.vtechphones.com.

For support, shopping, and everything new at VTech, visit our website at www.vtechphones.com. In Canada, please visit www.vtechcanada.com.

The ENERGY STAR® program (www.energystar.gov) recognizes and encourages the use of products that save energy and help protect our environment. We are proud to mark this product with the ENERGY STAR® label indicating it meets the latest energy efficiency guidelines.

Table of contents

 

Getting started....................................

1

Parts checklist.......................................

1

Battery installation and charging..........

2

Add and register a handset...................

3

Replace a handset................................

4

Handset layout......................................

5

Appendix.............................................

6

Battery...................................................

6

Important safety instructions................

7

Operating range....................................

8

Maintenance.........................................

8

About cordless telephones...................

9

The RBRC® seal...................................

9

Warranty.............................................

10

FCC, ACTA and IC regulations...........

12

Technical specifications......................

14

ii

Getting started

Parts checklist

Your telephone contains the following items. Save your sales receipt and original packaging in the event warranty service is necessary.

Battery compartment cover

Battery

Charger and charger adapter

Handset

User’s manual

To purchase a replacement battery or a power adapter, visit our website at www.vtechphones.com or call 1 (800) 595-9511.In Canada, go to www.vtechcanada.com or call 1 (800)267-7377.

Getting started

Battery installation and charging

Install the battery as shown below. After installing the battery, you might be able to make and receive short calls. For best performance, charge the

handset for at least 16 hours before use. When not in use, place the handset in the telephone base or charger. See page 6 for battery operating times.

Battery indicators

Battery status

Action

The screen is blank.

Battery has no charge

Charge until the screen shows

 

 

 

 

 

and the handset cannot

LOW BATTERY (at least 10

 

 

 

 

 

be used.

minutes).

 

 

 

 

 

 

 

The screen shows

Battery has very little

Charge until the screen shows

PLACE IN CHARGER

charge and the handset

LOW BATTERY (about four

and

 

flashes.

cannot be used.

minutes).

 

 

 

 

 

 

 

The screen shows

Battery has enough

Charge until the screen shows

LOW BATTERY,

charge to be used for a

HANDSET X (about one hour).

 

 

flashes, and the

short time.

 

 

 

handset beeps.

 

 

The screen shows

Battery is charged.

To keep the battery charged,

HANDSET X.

 

place it in the telephone base

 

 

 

 

 

 

or charger when not in use.

1.If the battery compartment cover is on the handset, press the indentation and slide the cover to remove.

2.Plug the battery connector securely into the socket inside the handset battery compartment, matching the color-codedlabel.

3.Place the battery with the label THIS SIDE UP facing up and the wires inside the battery compartment.

4.Align the cover flat against the battery compartment, then slide it towards the center of the handset until it clicks into place.

5.Charge the handset by placing it in the telephone base or charger. The

 

CHARGE light is on when the handset charges.

 

CHARGE

1

2

3

4

5

light

 

• When the screen shows LOW BATTERY, the backlight is off.

• If the handset will not be used for a long time, disconnect and remove the battery to prevent possible leakage.

To purchase replacement batteries, visit our website at www.vtechphones. com or call 1 (800) 595-9511.In Canada, go to www.vtechcanada.com or call 1 (800)267-7377.

Getting started

Add and register a handset

Each newly purchased handset (LS6205) must be registered to the telephone base (LS6215 orLS6225) before use. When first purchased, each expansion handset showsNOT REGISTERED.

When first purchased, each expansion handset shows NOT REGISTERED. You may need to charge the handset before registering to the telephone base. For more details on battery charging, see the table on page 2.

To register a handset:

1.Place the unregistered handset in the telephone base or charger. If PRESS FIND HS 4 SEC ON BASE does not appear on the handset screen after a few seconds, remove the handset and place it in the telephone base or charger again.

2.On the telephone base, press and hold

FIND HANDSET for about four seconds (until the redIN USE light on the telephone base turns on) and then release the

button. The handset shows PLEASE WAIT... and it takes up to 60 seconds to complete the registration. The handset showsHANDSET

X REGISTERED (X represents the handset number assigned) and you hear a beep when the registration completes.

When the registration is complete, the newly registered handset is assigned the next available handset registration number. For instance, if you

already have HANDSET 1 andHANDSET 2, the next registered handset is

HANDSET 3.

• If the registration fails, the handset shows NOT REGISTERED. To reset the handset, remove the handset from the telephone base or charger and place it back in. Try the registration process again.

You cannot register a handset if any other system handset is in use.

Only one handset can be registered at a time.

Getting started

Replace a handset

If you want to replace a handset or re-assignthe designated handset number of a registered handset, you mustde-registerall the handsets and then individually register each handset.

To make de-registrationeasier, read all of the instructions on this page before you begin. Tode-registerall handsets:

1.Press and hold FIND HANDSET on the telephone base for about 10 seconds (until theIN USE light on the telephone base turns on and starts to flash), then releaseFIND HANDSET.

2.Press and release FIND HANDSET again. You must pressFIND HANDSET while theIN USE light is still flashing. TheIN USE light flashes for approximately seven seconds.

3.All system handsets show CONNECTING... Thede-registrationprocess takes about 10 seconds to complete. All handsets showNOT REGISTERED when thede-registrationcompletes.

If de-registrationfails, you might need to reset the telephone and try again. To reset:

1.Pick up the registered handset and then press .

2.Press OFF/CLEAR and place the handset back in the telephone base.

-OR-

1.Unplug the power from the telephone base, then plug it back in.

You cannot de-registera handset if any system handset is in use.

Getting started

Handset layout

CHARGE light

On when the handset is charging in the telephone base or charger.

/ VOLp (Directory)

Press to enter the directory when the telephone is not in use.

While in a menu, press to scroll up.

During a call, press to raise the listening volume.

(Speakerphone)

Press to switch between speakerphone and handset.

Press to make or answer a call.

During a call, press to receive an incoming call when you receive a call waiting alert.

1

While reviewing a call log entry, press repeatedly to add or remove 1 in front of the telephone number before dialing or saving it in the directory.

REDIAL/PAUSE

Press to review the redial list.

While dialing or entering numbers into the directory, press and hold to insert a dialing pause.

CID / VOL(caller ID)

Press to review the call log when the telephone is not in use.

While in a menu, press to scroll down.

During a call, press to lower the listening volume.

MENU/SELECT

Press to show the menu.

While in a menu, press to select an item, or save an entry or setting.

OFF/CLEAR

During a call, press to hang up.

While the handset is ringing, press to silence the ringer temporarily.

Press and hold while the telephone is not in use to erase the missed calls indicator.

During programming, press to exit without making changes.

#

Press repeatedly to show other dialing options when

reviewing a call log entry.

INT (intercom)

• Press to initiate an intercom conversation or transfer a call.

MUTE/REMOVE

While on a call, press to mute the microphone.

While reviewing the call log or directory, press to delete an individual entry.

Press to delete digits when predialing.

Appendix

Battery

It takes up to 16 hours for the battery to be fully charged. When it is fully charged, you can expect the following performance:

Operation

Operating time

 

 

While in handset use (talking*)

Up to eight hours

 

 

While in speakerphone mode (talking*)

Up to five hours

 

 

While not in use (standby**)

Up to six days

 

 

*Operating times vary depending on your actual use and the age of the battery. **Handset is not charging or in use.

The battery needs charging when:

A new battery is installed in the handset.

The handset beeps.

A battery is properly installed and the screen is blank.

LOW BATTERY orPLACE IN CHARGER shows on the handset screen.

CAUTION:

To reduce the risk of fire or injury, read and follow these instructions:

Use only the battery(ies) provided or equivalent. To order a replacement, visit our website at www.vtechphones.com or call 1 (800) 595-9511.In Canada, go to www.vtechcanada.com or call 1 (800)267-7377.

Do not dispose of the battery(ies) in a fire. Check with local waste management codes for special disposal instructions.

Do not open or mutilate the battery(ies). Released electrolyte is corrosive and might cause burns or injury to the eyes or skin. The electrolyte might be toxic if swallowed.

Exercise care in handling batteries in order not to create a short circuit with conductive materials.

Charge the battery(ies) provided with or identified for use with this product only in accordance with the instructions and limitations specified in this manual.

Observe proper polarity orientation between the battery and metallic contacts.

To prevent fire or shock hazard, do not expose this product to water or any type of moisture.

Appendix

Important safety instructions

When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following:

1.Read and understand all instructions.

2.Follow all warnings and instructions marked on the product.

3.Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a dry non-abrasivecloth for cleaning.

4.Do not use this product near water.

5.Do not place this product on an unstable table, shelf, stand or other unstable surfaces.

6.Slots and openings in the back or bottom of the telephone base and handset are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register. This product should not be placed in any area where proper ventilation is not provided.

7.This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply in your home, consult your dealer or local power company.

8.Do not allow anything to rest on the power cord. Do not install this product where the cord may be walked on.

9.Never push objects of any kind into this product through the slots in the telephone base or handset because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind on the product.

10.To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing parts of the telephone base or handset other than specified access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used.

11.Do not overload wall outlets and extension cords.

12.Unplug this product from the wall outlet and refer servicing to an authorized service facility under the following conditions:

A.When the power supply cord or plug is damaged or frayed.

B.If liquid has been spilled onto the product.

C.If the product has been exposed to rain or water.

D.If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operation instructions. Improper adjustment of other controls may result in damage and often requires extensive work by an authorized technician to restore the product to normal operation.

E.If the product has been dropped and the telephone base and/or handset has been damaged.

F.If the product exhibits a distinct change in performance.

13.Avoid using a telephone (other than cordless) during an electrical storm. There is a remote risk of electric shock from lightning.

14.Do not use the telephone to report a gas leak in the vicinity of the leak.

15.Only put the handset of your telephone next to your ear when it is in normal talk mode.

16.The power adapters are intended to be correctly oriented in a vertical or floor mount position.

The prongs are not designed to hold the plug in place if it is plugged into a ceiling or an under- the-table/cabinetoutlet.

SAVE THESE INSTRUCTIONS

Appendix

Operating range

This cordless telephone operates with the maximum power allowed by the Federal Communications Commission (FCC). Even so, this handset and telephone base can communicate over only a certain distance - which can vary with the locations of the telephone base and handset, the weather, and the layout of your home or office.

When the handset is out of range, the handset displays CONNECTING...

If there is a call while the handset is out of range, it might not ring, or if it does ring, the call might not connect well when you press . Move closer to the telephone base, then pressto answer the call.

If the handset moves out of range during a telephone conversation, there might be interference. To improve reception, move closer to the telephone base.

Maintenance

Taking care of your telephone

Your cordless telephone contains sophisticated electronic parts, so it must be treated with care.

Avoid rough treatment

Place the handset down gently. Save the original packing materials to protect your telephone if you ever need to ship it.

Avoid water

Your telephone can be damaged if it gets wet. Do not use the handset outdoors in the rain, or handle it with wet hands. Do not install the telephone base near a sink, bathtub or shower.

Electrical storms

Electrical storms can sometimes cause power surges harmful to electronic equipment. For your own safety, take caution when using electrical appliances during storms.

Cleaning your telephone

Your telephone has a durable plastic casing that should retain its luster for many years. Clean it only with a dry non-abrasivecloth. Do not use dampened cloth or cleaning solvents of any kind.

Remember that electrical appliances can cause serious injury if used when you are wet or standing in the water. If the telephone base should fall into the water, DO NOT RETRIEVE IT UNTIL YOU UNPLUG THE POWER CORD AND TELEPHONE LINE CORD FROM THE WALL. Then remove the telephone by the unplugged cords.

Appendix

About cordless telephones

Privacy: The same features that make a cordless telephone convenient create some limitations. Telephone calls are transmitted between the telephone base and the cordless handset by radio waves, so there is a possibility that the cordless telephone conversations could be intercepted by radio receiving equipment within range of the cordless handset. For this reason, you should not think of cordless telephone conversations as being as private as those on corded telephones.

Electrical power: The telephone base of this cordless telephone must be connected to a working electrical outlet. The electrical outlet should not be controlled by a wall switch. Calls cannot be made from the cordless handset if the telephone base is unplugged or switched off, or if the electrical power is interrupted.

Potential TV interference: Some cordless telephones operate at frequencies that may cause interference to televisions and VCRs. To minimize or prevent such interference, do not place the telephone base of the cordless telephone near or on top of a TV or VCR. If interference is experienced, moving the cordless telephone farther away from the TV or VCR often reduces or eliminates the interference.

Rechargeable batteries: Exercise care in handling batteries in order not to create a short circuit with conducting material such as rings, bracelets, and keys. The battery or conductor may overheat and cause harm. Observe proper polarity between the battery and the battery charger.

Nickel-metal hydride rechargeable batteries: Dispose of these batteries in a safe manner. Do not burn or puncture the battery. Like other batteries of this type, if burned or punctured, they could release caustic material which could cause injury.

The RBRC® seal

The RBRC® seal on thenickel-metalhydride battery indicates that VTech Communications, Inc. is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful lives, when taken out of service within the United States and Canada.

The RBRC® program provides a convenient alternative to placing usednickel-metalhydride batteries into the trash or municipal waste, which may be illegal in your area.

VTech’s participation in RBRC® makes it easy for you to drop off the spent battery at local retailers participating in the RBRC® program or at authorized VTech product service centers. Please call1-800-8-BATTERYTM for information onNi-MHbattery recycling and disposal bans/restrictions in your area. VTech’s involvement in this program is part of its commitment to protecting our environment and conserving natural resources.

RBRC® is a registered trademark of Rechargeable Battery Recycling Corporation.

Appendix

Warranty

What does this limited warranty cover?

The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase (“Consumer” or “you”) that the Product and all accessories provided in the sales package (“Product”) are free from defects in material and workmanship, pursuant to the following terms and conditions, when installed and used normally and in accordance with the Product operating instructions. This limited warranty extends only to the Consumer for Products purchased and used in the United States of America and Canada.

What will VTech do if the Product is not free from defects in materials and workmanship during the limited warranty period (“Materially Defective Product”)?

During the limited warranty period, VTech’s authorized service representative will repair or replace at VTech’s option, without charge, a Materially Defective Product. If we repair the Product, we may use new or refurbished replacement parts. If we choose to replace the Product, we may replace

it with a new or refurbished Product of the same or similar design. We will retain defective parts, modules, or equipment. Repair or replacement of the Product, at VTech’s option, is your exclusive remedy. VTech will return the repaired or replacement Products to you in working condition. You should expect the repair or replacement to take approximately 30 days.

How long is the limited warranty period?

The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase. If VTech repairs or replaces a Materially Defective Product under the terms of this limited warranty, this limited warranty also applies to repaired or replacement Product for a period of either (a) 90 days from the date the repaired or replacement Product is shipped to you or (b) the time remaining on the original one-yearwarranty; whichever is longer.

What is not covered by this limited warranty?

This limited warranty does not cover:

1.Product that has been subjected to misuse, accident, shipping or other physical damage, improper installation, abnormal operation or handling, neglect, inundation, fire, water or other liquid intrusion; or

2.Product that has been damaged due to repair, alteration or modification by anyone other than an authorized service representative of VTech; or

3.Product to the extent that the problem experienced is caused by signal conditions, network reliability, or cable or antenna systems; or

4.Product to the extent that the problem is caused by use with non-VTechaccessories; or

5.Product whose warranty/quality stickers, product serial number plates or electronic serial numbers have been removed, altered or rendered illegible; or

6.Product purchased, used, serviced, or shipped for repair from outside the United States of America or Canada, or used for commercial or institutional purposes (including but not limited to Products used for rental purposes); or

7.Product returned without a valid proof of purchase (see item 2 below); or

8.Charges for installation or set up, adjustment of customer controls, and installation or repair of systems outside the unit.

10

Appendix

Warranty

How do you get warranty service?

To obtain warranty service in the United States of America, please call 1 (800) 595-9511.In Canada, please call 1 (800)267-7377.NOTE: Before calling for service, please review the user’s manual - a check of the Product’s controls and features may save you a service call.

Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and are responsible for delivery or handling charges incurred in the transport of the Product(s) to the service location. VTech will return repaired or replaced Product under this limited warranty. Transportation, delivery or handling charges are prepaid. VTech assumes no risk for damage or loss of the Product in transit. If the Product failure is not covered by this limited warranty, or proof of purchase does not meet the terms of this limited warranty, VTech will notify you and will request that you authorize the cost of repair prior to any further repair activity. You must pay for the cost of repair and return shipping costs for the repair of Products that are not covered by this limited warranty.

What must you return with the Product to get warranty service?

1.Return the entire original package and contents including the Product to the VTech service location along with a description of the malfunction or difficulty; and

2.Include a “valid proof of purchase” (sales receipt) identifying the Product purchased (Product model) and the date of purchase or receipt; and

3.Provide your name, complete and correct mailing address, and telephone number.

Other Limitations

This warranty is the complete and exclusive agreement between you and VTech. It supersedes all other written or oral communications related to this Product. VTech provides no other warranties for this Product. The warranty exclusively describes all of VTech’s responsibilities regarding the

Product. There are no other express warranties. No one is authorized to make modifications to this limited warranty and you should not rely on any such modification.

State/Provincial Law Rights: This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state or province to province.

Limitations: Implied warranties, including those of fitness for a particular purpose and merchantability (an unwritten warranty that the Product is fit for ordinary use) are limited to one year from the date of purchase. Some states/provinces do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. In no event shall VTech be liable for any indirect, special, incidental, consequential, or similar damages (including, but not limited to lost profits or revenue, inability to use the Product or other associated equipment, the cost of substitute equipment, and claims by third parties) resulting from the use of this Product. Some states/provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

Please retain your original sales receipt as proof of purchase.

11

Appendix

FCC, ACTA and IC regulations

FCC Part 15

This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Privacy of communications may not be ensured when using this telephone.

To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by a user or bystander according to the intended usage of the product. This product has been tested and found to comply with the FCC criteria. The handset may be safely held against the ear of the user. The telephone base shall be installed and used such that parts of the user’s body other than the hands are maintained at a distance of approximately 20 cm (8 inches) or more.

This Class B digital apparatus complies with Canadian ICES-003.

FCC Part 68 and ACTA

This equipment complies with Part 68 of the FCC rules and with technical requirements adopted by the Administrative Council for Terminal Attachments (ACTA). The label on the back or bottom of this equipment contains, among other things, a product identifier in the format US:AAAEQ##TXXXX.

This identifier must be provided to your local telephone company upon request.

The plug and jack used to connect this equipment to premises wiring and the telephone network must comply with applicable Part 68 rules and technical requirements adopted by ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. An RJ11 jack should normally be used for connecting to a single line and an RJ14 jack for two lines. See Installation Instructions in the user’s manual.

The Ringer Equivalence Number (REN) is used to determine how many devices you may connect to your telephone line and still have them ring when you are called. The REN for this product is encoded as the 6th and 7th characters following the US: in the product identifier (e.g., if ## is 03, the REN is 0.3). In most, but not all areas, the sum of all RENs should be five (5.0) or less. For more information, please contact your local telephone company.

This equipment may not be used with Party Lines. If you have specially wired alarm dialing equipment connected to your telephone line, ensure the connection of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.

If this equipment is malfunctioning, it must be unplugged from the modular jack until the problem has been corrected. Repairs to this telephone equipment can only be made by the manufacturer or its authorized agents. For repair procedures, follow the instructions outlined under the Limited Warranty.

12

Appendix

FCC, ACTA and IC regulations

If this equipment is causing harm to the telephone network, the telephone company may temporarily discontinue your telephone service. The telephone company is required to notify you before interrupting service. If advance notice is not practical, you will be notified as soon as possible. You will be given the opportunity to correct the problem and the telephone company is required to inform you of your right to file a complaint with the FCC. Your telephone company may make changes in its facilities, equipment, operation, or procedures that could affect the proper functioning of this product. The telephone company is required to notify you if such changes are planned.

If this product is equipped with a corded or cordless handset, it is hearing aid compatible.

If this product has memory dialing locations, you may choose to store emergency telephone numbers (e.g., police, fire, medical) in these locations. If you do store or test emergency numbers, please:

Remain on the line and briefly explain the reason for the call before hanging up.

Perform such activities in off-peakhours, such as early morning or late evening.

Industry Canada

Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference, including interference that may cause undesired operation.

The term ‘’IC:‘’ before the certification/registration number only signifies that the Industry Canada technical specifications were met.

The Ringer Equivalence Number (REN) for this terminal equipment is 0.1. The REN is an indication of the maximum number of devices allowed to be connected to a telephone interface.

The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the RENs of all the devices does not exceed five.

This product meets the applicable Industry Canada technical specifications.

13

Appendix

Technical specifications

Frequency control

Crystal controlled PLL synthesizer

 

 

Transmit

Handset: 1921.536-1928.448MHz

frequency

Telephone base: 1921.536-1928.448MHz

Channels

5

 

 

Nominal effective

Maximum power allowed by FCC and IC. Actual operating

range

range might vary according to environmental conditions at the

 

time of use.

 

 

Size

Handset: 6.34 X 1.81 X 0.63 in (161.00 X 46.00 X 16.00 mm)

 

Charger: 2.76 X 3.15 X 1.77 in (70.00 X 80.00 X 45.00 mm)

 

 

Weight

Handset: 3.68oz (104.20g) (including battery)

 

Charger: 3.27oz (92.60g)

 

 

Power

Handset: 2.4V 500mAh Ni-MHbattery

requirements

Charger: 6V AC @ 300mA

 

 

Memory

Handset directory: 50 memory locations;

 

up to 30 digits and 15 characters

 

Handset call log: 50 memory locations;

 

up to 24 digits and 15 characters

 

 

14

VTECH TELECOMMUNICATIONS LTD. A member of THE VTECH GROUP OF COMPANIES.

Distributed in the U.S.A. by VTech Communications, Inc. Beaverton, Oregon 97008 Distributed in Canada by VTech Technologies Canada, Ltd., Richmond, B.C. V6W 1L5 Copyright © 2009 for VTECH TELECOMMUNICATIONS LTD.

Printed in China.

91-002280-020-100