Vinotemp WINE-MATE WM2500 HTD User Manual

Size:
428.9 Kb
Download

WINE-MATE Cooling Unit

Use & Care Manual

WM1500 HTD, HTD-TE

WM2500 HTD, HTD-TE

Vinotemp International Corp.

www.winemate.com

Important Safety Information

DO NOT PLUG IN UNTIL 24 HOURS AFTER DELIVERY.

DO NOT USE A GROUND FAULT INTERRUPTER (GFI).

A DEDICATED 15 AMPCIRCUIT IS HIGHLY RECOMMENDED.

-1 -

TABLE OF CONTENTS

Feature Description…………………………….……………..3

Installation Instruction………………………………………..5

Temperature Control & Humidity Adjustment……..…….8

Care Guide……………………………………………………12

Troubleshooting……………………………………………..14

Wiring Diagram……………………………………….………17

Customer Support……………………………………………18

Warranty……………………………………………………….19

- 2 -

Feature Description

WM1500HTD, HTD-TEand WM2500HTD,HTD-TEcooling units are designed and used to provide a subtle temperature between 50~65 °F for suitable space at a normal environment.

The refrigerated space will maintain humidity of 50~70% RH even when the environment becomes dry and humid.

These temperatures and humilities are optimized for long term storage of wine.

Humidity and temperature digital control using patent pending technology

Optimized air flow for most even temperatures in wine cabinets

Exchangeable supply grille for front, back and down cold air distribution

Multiple options for top and rear hot air exhaust

High efficient tube-axialfans for both condenser and evaporator

Extra insulation for both thermal and noise isolation

Unique condensate drain tray for humidity adjustment

Grill size optimized for easy cleaning and safety

Stamping ribbed housing for robust structure

Self-containedready for use and easy for installation

Fig. 1.1 FEATURE DESCRIPTION

- 3 -

Fig. 1.2 DIMENSIONS (in)

The dimensions and capacity are specified as follows:

 

 

Cooling

Bottle

 

 

Model

Exhaust

Capacity,

Electrical

Weight

Capacity

CFM

 

 

55°F/75°F

 

 

 

 

55°F/75°F

 

 

 

 

 

 

 

 

1500htd

Rear Exhaust

1500 Btu/h,

150 cu ft

800

115V/60Hz 4A

55 lb

 

 

120 CFM

 

bottles

 

 

1500htd-te

Top Exhaust

1500 Btu/h,

150 cu ft

800

115V/60Hz 4A

55 lb

120 CFM

bottles

2500htd

Rear Exhaust

2500 Btu/h,

250 cu ft

1200

115V/60Hz 5A

60 lb

 

 

180 CFM

 

bottles

 

 

2500htd-te

Top Exhaust

2500 Btu/h,

250 cu ft

1200

115V/60Hz 5A

60 lb

180 CFM

bottles

See the voltage, frequency and current on the nameplate at the cooling unit.

- 4 -

Installation Instruction

1.Cabinet Location

Place the wine cabinet in a properly ventilated location. Otherwise, heat exhausted by the cooling unit will build up and it will not operate properly.

The exhaust area must not be closed space and must be ventilated. The ambient temperatures shall not be higher than 90 °F or lower than 50°F.

1) Rear Exhaust Location

Leave min 6 “clearance from the rear to the wall.

Leave min 12” clearance from the top to the ceiling.

Leave min 6” clearance from the left and right sides.

2) Front Exhaust Location

• Leave min 6” clearance from the front if left and right sides unobstructed.

• Or, leave min 36” clearance from the front if left and right sides obstructed

3) Top Exhaust Location

Leave min 12” from the top to the ceiling.

Leave min 2 “clearance from the rear to the wall.

Leave min 2” clearance from the left and right sides.

4) Side Exhaust Location

Leave min 6 “clearance from the left or right side to the wall.

Leave min 12” clearance from the top to the ceiling.

2.Installation

Fig. 2.1 COOLING UNIT MOUNTING

- 5 -

Fig. 2.2 COOLING UNIT MOUNTING

Fig. 2.3 MOUNTING CUTOUT & GASKET LIPS

(LOCATED AT THE CABINET)

- 6 -

Fig. 2.3 TOP EXHAUST GASKET

(LOCATED ON THE COOLING UNIT)

Cut a rectangular inside opening at the rear of the cabinet with the 1/4” clearance inwards to the width and height of the cooling unit. By not going through, leave 1/2” lip inside at the wall to place the gaskets (see Fig. 2.2).

If top exhaust, cut another rectangular opening at the top of the cabinet to the length and width of the top exhaust (see Fig.2.2).

Make 2 holes at the ceiling to install the 1/4 inside diameter wood thread inserts (see Fig.2.2).

Place the gaskets (1) on the gasket lips (see Fig 2.1).

If top exhaust, place another gaskets along the top exhaust at the top of the cooling unit (see Fig.2.3).

Place the cooling unit to a flat and stable place.

Then move it on the top of the wine rack temporally.

Move the cooling unit towards the mounting sides and push to press the gaskets.

Fasten the 2 brackets and use 7/16” wrench to tighten the 2 screws (see

Fig 2.1).

If top exhaust, install another top exhaust grille at the top of the cabinet.

Plug the cooling unit in receptacle.

Plug the wine cabinet.

NOTE: DO NOT INSTALL ANY DUCTS ONTO THE SUPPLY, INTAKE ANY EXHAUST.

3.Electrical Cord

Because of potential safety hazards under a certain condition, we strongly recommend against the use of an extension cord. However, if you still elect to use an extension cord, it is absolutely necessary that it will be a UL LISTED 3-wiregrounding type appliance extension cord having a 3- blade grounding plug and a3-slotreceptacle that will plug into the appliance. The marked rating of the extension cord shall be 115 V, 15 A.

-7 -

Temperature Control & Humidity Adjustment

1. Temperature Setting

Set the temperature at 55 °F for the optimum aging of wine

On initial start-up,the time required to reach the desired temperature will vary, depending on the quantity of bottles, temperature setting and surrounding temperature.

Allow 24 hours to stabilize the temperature for each new temperature setting operation

2. Use of the controller

Fig. 3.1 DIGITAL CONTROLLER

1) Display

During normal operating conditions, the display shows the value measured by the air regulation probe. In case of active alarm, the temperature flashes alternately to the code alarm.

1.1 LED Functions

1.2 Front Panel Commands

- 8 -

2) Alarm Signals

2.1 Code Description

2.2 Alarm Recovery

Probe alarms P1”, start a few seconds after the fault in the related probe; they automatically stop a few seconds after the probe restarts normal operation. Check connections before replacing the probe. Temperature alarms “HA”, “LA” automatically stops as soon as the temperature returns to normal value. Alarm “CA” (with i1F=PAL) recovers only by switching off and on the instrument.

3) Temperature Set-Point

3.1 How to see the set-point

1.Push and immediately release the SET key: the display will show the Set-pointvalue;

2.Push and immediately release the SET key or wait for 5 seconds to display the probe value again.

-9 -