Vinotemp WINE-MATE WM-8500HTD User Manual

Size:
621.5 Kb
Download

WINE-MATE Cooling Unit

Use & Care Manual

VINO1500HZD

VINO2500HZD

VINO3500HZD

VINO4500HZD

VINO6500HZD

VINO8500HZD

Vinotemp International Corp.

www.winemate.com

Important Safety Information

DO NOT PLUG IN UNTIL 24 HOURS AFTER DELIVERY.

DO NOT USE A GROUND FAULT INTERRUPTER (GFI).

A DEDICATED 15 OR 20 AMPCIRCUIT IS HIGHLY RECOMMENDED.

-1 -

TABLE OF CONTENTS

Feature Description…………………………….……………..3

Installation Instruction………………………………………..5

Temperature Control & Humidity Adjustment...………..13

Care Guide…………………………………………………….16

Troubleshooting……………………………………………..17

Wiring Diagram……………………………………….………20

Customer Support……………………………………………22

Warranty……………………………………………………….23

- 2 -

Feature Description

HZD cooling unit is designed and used to provide a stable temperature between 50~65 °F for suitable space at a normal environment.

The refrigerated space will maintain humidity of 50~70% RH even when the environment becomes dry and humid.

These temperatures and humilities are optimized for long term storage of wine, fur and tobacco.

Horizontal cold-airsupply is optimized for use in the wide cabinets or wine rooms.

Self-containedready for use and easy for installation

Fig. 1.1 FEATURE DESCRIPTIONS

- 3 -

See the voltage, frequency and current from the label on the back or side of the cooling unit.

The dimension and capacity are specified as follows:

 

 

COOLING

BOTTLE

 

 

 

 

 

 

CAPACITY,

DIMENSIONS IN.

 

WEIGHT

 

MODEL

CAPACITY

ELECTRICAL

 

CFM

WXHXD

(lb)

 

 

55°F/75°F

 

 

 

55°F/75°F

 

 

 

 

 

 

 

 

 

 

 

 

 

VINO-

1500 Btu/h,

150

800

14.25X13.25X 16

115V/60HZ/4A

50

 

 

1500HZD

120 CFM

cu ft

bottles

 

 

 

 

 

 

 

VINO-

2500 Btu/h,

250

1200

14.25X13.25X 16

115V/60HZ/5A

55

 

 

2500HZD

180 CFM

cu ft

bottles

 

 

 

 

 

 

 

VINO-

3500 Btu/h,

650

3000

14.25x19.75x21.25

115V/60Hz/6A

75

 

 

3500HZD

250 CFM

cu ft

bottles

 

 

 

 

 

 

 

VINO-

4500 Btu/h,

1000

4500

14.25x19.75x21.25

115V/60Hz/9A

75

 

 

4500HZD

250 CFM

cu ft

bottles

 

 

 

 

 

 

 

VINO-

6500 Btu/h,

1500

6500

17x22x28

115V/60Hz/14A

110

 

 

6500HZD

500 CFM

cu ft

bottles

 

 

 

 

 

 

 

VINO-

8500 Btu/h,

2000

8500

17x22x28

115V/60Hz/16A

110

 

 

8500HZD

500 CFM

cu ft

bottles

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Fig. 1.2 DIMENSIONS

- 4 -

Installation Instruction

Select a place to mount the unit where the exhaust airflow is unobstructed for a minimum of 6 inch. The area into which the unit exhausts must be well ventilated.

If it is not, heat exhausted by the unit will build up and the unit will not operate properly. The ambient temperatures shall not be higher than 90 °F or lower than 50°F. Additionally, cold supply air from the front grille must remain unobstructed. The unit shall be mounted near the ceiling with equal distance from each side of the cabinet or room.

1. VINO1500-2500HZDCABINET INSTALLATION

Fig. 2.1 CABINET CUTOUT & GASKET LIP

- 5 -

Fig. 2.2 GASKET

Fig. 2.3 TOP EXHAUST GASKET

- 6 -

Fig. 2.4 THREAD INSERT

Fig. 2.5 COOLING UNIT

- 7 -

Fig. 2.6 FASTENING BRACKET & SCREW

- 8 -

Fig. 2.7 CABINET GRILLE

Cut a rectangular inside opening with the 1/4” clearance inwards to the width and height of the cooling unit. By not going through, leave 1/2” lip inside at the wall to place the gaskets (see Fig 2.1 & 2.2).

If top exhaust, cut another rectangular opening at the top of the cabinet to the length and width of the top exhaust.

Make 2 holes at the ceiling to install the 1/4 inside diameter wood thread inserts (see Fig.2.1 & 2.4).

Place the gaskets on the mounting lip sides (see Fig 2.2).

If top exhaust, place another gaskets along the top exhaust at the top of the cooling unit (see Fig.2.3).

Place the cooling unit to a flat and stable place.

Then move it on the top of the wine rack temporally.

Move the cooling unit towards the mounting sides and push to press the gaskets (see Fig 2.5).

Fasten the 2 brackets and use 7/16” wrench to tighten the 2 screws (see Fig 2.6).

Attach the exhaust and fresh air grille from the rear side of the cellar (see

Fig 2.7).

-9 -