POWER ON BOARD 2 YEAR LIMITED WARRANTY PROGRAM
This limited warranty program is the only one that applies to this product, and it sets forth all the responsibilities of Power on Board, regarding this product. There is no other warranty, other than those described herein.
This Power on Board product is warranted, to the original purchaser only, to be free of defects in materials and workmanship for two years from the date of purchase without additional charge. The warranty does not extend to subsequent purchasers or users. Power on Board will not be responsible for any amount of damage in excess of the retail purchase price of the product under any circumstances. Incidental and consequential damages are specifically excluded from coverage under this warranty.
This product is not intended for commercial use. This warranty does not apply to accessories or damage to units from misuse or incorrect connection/installation. Misuse includes wiring or connecting to improper polarity power sources.
RETURN/REPAIR POLICY: Defective products, other than accessories, may be returned to Power on Board. Any defective product, other than accessories, that is returned to Power on Board within 30 days of the date of purchase will be replaced free of charge. If such a product is returned more than 30 days but less than two years from the purchase date, Power on Board will repair the unit or, at its option, replace it free of charge.
If the unit is repaired, new or reconditioned, replacement parts may be used, at Power on Board’s option. A unit may be replaced with a new or reconditioned unit of the same or comparable design. The repaired or replaced unit will then be warranted under the terms of the remainder of the warranty period. The customer is responsible for the shipping charges on all returned items after 30 days. During the warranty period, Power on Board will be responsible for the return shipping charges.
LIMITATIONS: This warranty does not cover accessories, bulbs, fuses and batteries, defects resulting from normal wear and tear (including chips, scratches, abrasions, discoloration or fading due to usage or exposure to sunlight), accidents, damage during shipping to our service facility, alterations, unauthorized use or repair, neglect, misuse, abuse, failure to follow instructions for care and maintenance, fire, flood or Acts of God.
If your problem is not covered by this warranty, call our Technical Support Department at (954) 584-4446 or toll free at (866) 584-5504 for general repair information and charges if applicable.
STATE LAW RIGHTS: This warranty gives you specific legal rights. Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the exclusions or limitations stated herein may not apply. This warranty gives the purchaser specific legal rights; other rights, which vary from state to state, may apply.
TO REQUEST WARRANTY SERVICE FOR THIS PRODUCT: Contact Power on Board Technical Support by telephone, fax or mail. We suggest that you keep the original packaging in case you need to ship the unit. When returning a product, include your name, address, phone number, dated sales receipt (or copy) and a description of the reason for return and product serial number. After repairing or replacing the unit, we will make every effort to return it to you within four weeks.
WARRANTY ACTIVATION: Please complete Warranty Activation Card and mail to Power on Board. Enter “VEC1028POB” as Model and “Power Center” as Product Type. All Power on Board products must be registered within 30 days of purchase to activate this warranty. Mail the completed registration form, along with a copy of the original sales receipt to:
ATTN.: CUSTOMER SERVICE
4140 SW 30th Ave., Ft. Lauderdale, FL 33312
• PH: 954-584-4446 • TOLL FREE: 866-584-5504 • FAX: 954-584-5556 •
WARRANTY IS NON-TRANSFERABLE AND NON-REFUNDABLE.
BD051605
© 2006 VECTOR MANUFACTURING
MADE IN CHINA
VEC1028POB
Rechargeable
Power Center
AC/DC Portable Power Supply
Jump-Starter/Air Compressor/Inflator
USER’S MANUAL
& WARRANTY INFORMATION
IMPORTANT SAFETY INFORMATION, SAVE THESE INSTRUCTIONS
TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND THIS INSTRUCTIONAL MANUAL. THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING THE OPERATION AND WARRANTY OF THIS PRODUCT. PLEASE RETAIN FOR FUTURE REFERENCE.
4140 S.W. 30th Ave., Ft. Lauderdale, FL 33312
Toll Free: (866) 584-5504
IMPORTANT SAFETY INSTRUCTIONS
WARNINGS
1.RISK OF EXPLOSIVE GAS MIXTURES — WORKING IN THE VICINITY OF A LEAD-ACID BATTERY IS DANGEROUS. BATTERIES GENERATE EXPLOSIVE GASES DURING NORMAL BATTERY OPERATION. FOR THIS REASON, IT IS OF UTMOST IMPORTANCE THAT EACH TIME BEFORE USING THIS UNIT, YOU READ THIS MANUAL AND FOLLOW THE INSTRUCTIONS EXACTLY.
2.To reduce risk of battery explosion, follow these instructions and those published by the battery manufacturer and manufacturer of any equipment you intend to use in vicinity of battery. Review cautionary markings on these products and on engine.
3.This equipment employs parts (switches, relays, etc.) that produce arcs or sparks. Therefore, if used in a garage or enclosed area, the unit MUST be placed not less than 18 inches above the floor.
Battery Safety
1.When working with lead acid batteries, always make sure immediate assistance is available in case of accident or emergency.
2.Always use protective eyewear when using this product: contact with battery acid may cause blindness and/or severe burns. Be aware of first aid procedures in case of accidental contact with battery acid.
3.There is a risk of releasing explosive gases when lead acid batteries are charged or discharged. Failure to follow instructions may cause property damage and/or personal injury.
4.When connecting the battery clamps to a discharged battery and an alarm sounds — the clamp connections are incorrect and need to be reversed.
5.Jump-start procedures should only be performed in a safe, dry, well-ventilated area.
6.Always store battery clamps on the clamp tabs on the back of the unit when not in use. Never touch battery clamps together. This can cause dangerous sparks, power arcing and/or explosion.
7.When using this unit close to the vehicle’s battery and engine, stand the unit on a flat, stable surface, and be sure to keep all clamps, cords, clothing and body parts away from moving vehicle parts.
8.Do not wear vinyl clothing when jump-starting a vehicle, friction can cause dangerous staticelectrical sparks. Remove all jewelry or metal objects that could cause short circuits or react with battery acid.
9.Never allow RED and BLACK clamps to touch each other or another common metal conductor — this could cause damage to the unit and/or create a sparking/explosion hazard.
10.a. For negative-grounded systems (most common), connect the POSITIVE (RED) clamp to the POSITIVE ungrounded battery post and the NEGATIVE (BLACK) clamp to the vehicle chassis or engine block away from the battery. Do not connect the clamp to the carburetor, fuel lines or sheet-metal body parts. Connect to a heavy gauge metal part of the frame or engine block.
b.For positive-grounded systems, connect the NEGATIVE (BLACK) clamp to the NEGATIVE ungrounded battery post and the POSITIVE (RED) clamp to the vehicle chassis or engine block away from the battery. Do not connect the clamp to the carburetor, fuel lines or sheet-metal body parts. Connect to a heavy gauge metal part of the frame or engine block.
11.Always disconnect the NEGATIVE (BLACK) jumper cable first, followed by the POSITIVE (RED) jumper cable, except for positive grounded systems.
12.Do not expose battery to fire or intense heat since it may explode. Before disposing of the battery, protect exposed terminals with heavy-duty electrical tape to prevent shorting (shorting can result in injury or fire).
13.Do not smoke or use flammable items (matches, cigarette lighters, etc.) while working on a vehicle’s battery system.
14.DO NOT ATTEMPT TO JUMP-START A FROZEN BATTERY.
15.Place this unit as far away from the battery as DC cables permit.
16.Never allow battery acid to come in contact with this unit.
17.Vehicles that have on-board computerized systems may be damaged if vehicle battery is jumpstarted. Before jump-starting, read the vehicle’s owners manual to confirm that external-starting assistance is suitable.
Compressor/Inflator Safety
1.Never attempt to disable or block the inflation and deflation ports while pump is operating.
2.Never cover unit at any time.
3.Never leave the pump unattended while in use.
4.Never allow sand, small rocks or other debris to be sucked into the inflation or deflation ports.
5.Never look into or point the inflator port opening toward anyone’s eyes.
6.Do not use the compressor continuously for longer than 15 minutes. Extended use will cause it to overheat and can damage the product. After 15 minutes of continuous use, turn the unit OFF and wait 15 minutes before resuming operation of the compressor.
7.DO NOT overinflate objects or exceed manufacturer’s recommendations for pressure on objects to be inflated.
Personal Safety
FIRST AID
SKIN: If battery acid comes in contact with skin, rinse immediately with water, then wash thoroughly with soap and water. If redness, pain or irritation occurs, seek immediate medical attention.
EYES: If battery acid comes in contact with eyes, flush eyes immediately for a minimum of 15 minutes and seek immediate medical attention.
CAUTIONS
1.When using an extension cord (not supplied) for AC charging/recharging, make sure it has the same configuration as the plug of the unit and that the cord is properly wired and in good condition. The cord must be suitable for 120 volts AC and have a minimum 2 amp rating.
2.Do not recharge for more than 5-6 hours maximum using the 12 volt DC method. Recharge unit after each use.
3.All ON/OFF switches should be in the OFF position when the unit is charging or not in use. Make sure all switches are in the OFF position before connection to a power source or load.
4.Never insert anything other than the supplied power/recharging cords or recommended appliance power/recharging cords into the 12 volt DC charging/power outlet on this unit. Do not use any accessory that is not recommended or provided by the manufacturer.
5.Do not use this unit to operate appliances that need more than 5 amps to operate from the 12 volt DC accessory outlet.
6.This system is designed to be used only on vehicles with a 12 volt DC battery system. Do not connect to a 6 volt or 24 volt battery system.
7.This system is not designed to be used as a replacement for a vehicle battery. Do not attempt to operate a vehicle that does not have a battery installed.
8.Excessive engine cranking can damage a vehicle’s starter motor. If the engine fails to start after the recommended number of attempts, discontinue jump-start procedures and look for other problems that may need to be corrected.
9.Although this unit contains a non-spillable battery, it is recommended that unit be kept upright during storage, use and recharging. To avoid possible damage that may shorten the unit’s working life, protect it from direct sunlight, direct heat and/or moisture.
10.Check unit periodically for wear and tear. Contact the Customer Service Department at (866) 584-5504 to replace worn or defective parts.
11.Do not drop this unit as it may damage the product. If unit is dropped or damaged, please discontinue using it.
12.NEVER submerge this unit in water.
13.Store indoors. Do not operate unit in rain or snow, or use when wet.
14.Do not operate this unit in a closed area or restrict ventilation in any way.
THIS UNIT IS NOT FOR USE BY CHILDREN AND SHOULD ONLY BE OPERATED BY ADULTS.
SAVE THESE INSTRUCTIONS
ii |
iii |
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
TABLE OF CONTENTS
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 AC and DC Charging/Recharging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Viewing Battery Charge Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 120 Volt AC Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 12 Volt DC Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Using the Power Center as a Jump-Starter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Using the 12 Volt Portable Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Using the 120 Volt AC Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Using the Emergency Area Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Using the Air Compressor/Inflator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Inflating Products With a Valve Stem Using the Compressor . . . . . . . . . . . . . . . 7 Inflating Products Without a Valve Stem Using the Compressor . . . . . . . . . . . . . 8 Using the Inflator/Deflator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Battery Replacement/Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Fuse Replacement (DC Accessory Adapter) . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
INTRODUCTION
Thank you for purchasing the VEC1028POB Power Center. Please read this guide carefully before use to ensure optimum performance and avoid damage to the unit.
FEATURES
•Powers 110/120 volt AC appliances
•Powers 12 volt DC appliances
•Jump-starts vehicle engines
•Built-in air compressor/inflator with pressure gauge, hoses and adapters
•Built-in 400 watt inverter
•Includes non-spillable, maintenance-free, heavy-duty, sealed battery
•Safe to use, transport and store
•Reverse polarity connection warning
•Self-stored jumper cables
•Requires no maintenance (other than recharging) for optimum operation
•Rechargeable with built-in AC charger
•Unique compact design provides completely portable 12 volt DC power
•Molded high-impact case is tough and durable
•Built-in area light for night time roadside repairs and use in remote locations without utility power
•Battery charge level indicators
iv |
1 |
Loading...