DECT 2005
Accessory handset for
DECT 2015 Series
DECT 2035 Series
Welcome
Congratulations on your purchase of the Uniden DECT2005 accessory handset and charging cradle. You can place this fully featured cordless handset anywhere your home has AC power.
Note: Illustrations in this manual are used for explanation purposes. Some illustrations may differ from the actual unit.
Important!
The DECT2005 accessory handset will not operate until it is registered to a Uniden main base. This manual describes how to set up your new handset; for more detailed instructions on operating your new handset, please refer to the manual supplied with your base.
Terminology Used in this Manual
Accessory |
A handset that works with an expandable phone base. |
|
Handset |
Accessory handsets must be registered to a base. |
|
Base |
The main part of the phone that connects to your phone |
|
line, and lets you make and receive calls. |
||
|
||
Charging |
A cradle that charges an accessory handset. It connects to |
|
cradle |
power but not to a phone line. |
|
|
The handset is not in use. No line has been activated. |
|
Standby |
(It doesn’t matter whether the handset is in the cradle.) |
|
|
No dial tone is present. |
|
Station |
Any registered handset or the base. |
|
Talk |
A dial tone has been enabled, so you can dial and carry on |
|
a conversation with an outside party. |
||
|
1
Compatible Bases
This handset is compatible with Uniden’s 1.8 GHz DECT Expandable phone system: the DECT2015 and DECT2035 series.
Installing the Accessory Handset
Checking the Package Contents
Make sure your package contains the following items. If any items are missing or damaged, please contact your place of purchase immediately.
• Cordless Handset |
• Printed Material |
•Charging cradle with AC Adapter (model # AAD-600S(M):
Input 240V AC, 50Hz; Output 9V DC, 210 mA)
•Rechargeable Ni-Cd Battery Pack (model # BT-904)
2
Installing the Battery
Use only the Uniden BT-904 rechargeable battery pack supplied with your cordless telephone.
Unpack the handset, battery pack and battery cover.(If the battery cover is on the handset, press in on the notch and slide the cover off.)
Push the battery pack connector in firmly. (You should hear it click into place.) Gently tug on the battery wires to make sure the connection is secure.
Place the cover over the battery compartment and slide it up into place.
Line up the red and black wires on the battery pack connector with the sticker in the handset’s battery compartment.
RED
BLACK
3
Charging the Accessory Handset
The handset is powered by a rechargeable battery pack that automatically recharges when the handset is placed in the charging cradle.
Use only the Uniden AAD-600S(M) AC adapter with the charging cradle.
Connect the AC adapter to the DC IN 9V jack as shown. (It may already be connected.)
Connect the AC adapter to a standard 240V AC wall outlet.
Place the handset in the with the
forward.
Make sure that the charge LED illuminates when the handset is seated.
Check the AC adapter connection.
Make sure you are not using an outlet that’s controlled by a wall switch.
Charge your handset at least 15 to 20 hours before using your new handset for the first time.
4
Registering the Handset
You must register the handset to the base before you can use it. Only one handset can be registered at a time. (If an accessory handset has ever been registered to a base, you must reset the
handset before you can register it to a new base.)
To register to a DECT2015 or DECT2035 base:
Place the accessory handset in the base. While the handset is registering, Handset Registering appears in the LCD. When
Registration complete is displayed, the handset has been registered to the base.
What if the display shows
Registration failed?
Pick up the handset from the base and try again.
1
Extra Handset |
Charge the handset |
|
for 15-20 hours. |
Charging cradle |
|
2
Extra Handset
Place the extra handset in the main base to
register.
Main
4
Extra Handset
3 Main+Base
Charging cradle
5
Resetting the Handset
If you want to register the handset to a different base or replace a handset with another one, you must first clear the registration
information from the base and the handset.
111Press and hold END and # for at least five seconds, until the
SYSTEM RESET menu appears.
222Select the Deregister HS
submenu by pressing MENU/ SELECT. Which Handset? appears in the display.
333Use or to select the
handset ID to be de-registered from the list, and then press
MENU/SELECT. Deregister HS appears.
444Press to move the cursor to Yes, and then press
MENU/SELECT. You will hear a confirmation tone.
6
Resetting the Handset Without the Base
If the original base this handset was registered to is not available for some reason (for example, it is lost or somehow incapacitated), you can still reset the handset and use it with another base.
111Press and hold END and # for at least five seconds, until the
SYSTEM RESET menu appears.
222Press to move the cursor to Base Unavailable and then press MENU/SELECT.
333Press to move the cursor to the base which you want to de-register from, and then press MENU/SELECT. Base Unavailable appears.
444Press to move the cursor to Yes, and then press
MENU/SELECT. You hear a confirmation tone, and the handset deletes its own link to the base without trying to contact the base.
Now you are ready to register the handset to the new base.
7