Tripp Lite APS-PV User Manual

0 (0)

1111 W. 35th Street

Chicago, IL 60609 USA

Customer Support: (773) 869-1234

www.tripplite.com

Owner’s Manual

APS/PV Remote

for PowerVerter APS and PowerVerter Plus Models

ESPAÑOL: p. 3

The APS/PV Remote allows you to monitor and control at a distance many of the functions of a Tripp Lite PowerVerter Plus or PowerVerter APS model featuring a RJ11 Remote Port.

Installation

Label

For Use with a PowerVerter APS: Affix the label marked "APS Remote" to the front of the Remote so that the holes in the label align with the Remote's LEDs and switch.

For Use with a PowerVerter Plus: Affix the label marked "PV Remote" to the front of the Remote so that the holes in the label align with the Remote's LEDs and switch.

Cable: Insert one end of the 50' Remote Cable into the Remote Port on the front of your PowerVerter. Insert the other end into the RJ11 port on the bottom of the Remote.

Mounting: Using two to four screws appropriate to your mounting surface*, attach the Remote securely so that the LEDs can be clearly seen.

* Screws must be provided by the user.

Operation

PV Remote

APS Remote

1. BATTERY LOW/MED/HIGH LEDs (Both Remotes)

These three lights show the approximate charge of your connected batteries.

LEDs Illuminated	Approximate Charge
Green	96%	- Full
Green & yellow	81%	- 95%
Yellow	61%	- 80%
Yellow & red	41%	- 60%
Red	21%	- 40%

All

three

lights

off

1% - 20%

Flashing

red

0% (Inverter shutdown)

All three lights flash slowly

Excessive

discharge

All

three

lights

flash quickly

Overcharge

or charger fault

2. OFF/ON Switch (PV Remote)

Move this switch to the ON position to have your PowerVerter provide connected equipment with AC power by converting DC power from an attached battery. To prevent battery drain, leave it in the OFF position when not using connected equipment.

3. LOAD LOW/MED/HIGH LEDs (PV Remote)

These three lights show the approximate voltage demand on your PowerVerter Plus.

LEDs Illuminated	ApproximateLoad
Green	0% - 20%
Green & yellow	21%	- 40%
Yellow	41%	- 60%
Yellow & red	61%	- 80%
Red	81%	- Full
All three lights off	Inverter off
Flashing red	Overload

4. AUTO/CHARGE ONLY Switch (APS Remote)

Move this switch to the AUTO position to have the APS provide connected equipment with AC power (convertedfromDCpowerfromattachedbatteries)intheeventofanACpoweroutage.MoveittotheCHARGE ONLY position when equipment is not in use to conserve battery power by disabling the inverter. In either position, the APS will supply AC power to connected equipment and charge connected batteries while AC input is present.

5. LINE LED (APS Remote)

This green light will turn continuously ON when the APS is receiving AC power input if the APS is set to AUTO/REMOTE and the Remote is set to AUTO. This indicates that the APS will provide power from battery backup if utility power fails. It will flash intermittently when the APS is receiving AC power input if the APS is set to AUTO/REMOTE and the Remote is set to CHARGE ONLY to warn you that the APS WILL NOT provide battery backup during AC power outages.

6. INV LED (APS Remote)

This yellow light will turn continuously ON when connected equipment is receiving battery-supplied AC power (i.e. during a power outage or when the APS is disconnected from AC input).

7. LOAD LED (APS Remote)

This red light will turn continuously ON to warn that the APS’s load is between 80% and 110% of capacity. The light will flash when the APS's inverter shuts down due to a severe overload or overheating. If this happens, turn the APS OFF, remove the overload and let the APS cool before turning it ON again.

Limited Warranty

Tripp Lite warrants its products to be free from defects in materials and workmanship for a period of one year (domestic)or120days(export)fromthedateofinitialpurchase. TrippLite’sobligationunderthiswarrantyislimited torepairingorreplacing(atitssoleoption)anysuchdefectiveproducts.Toobtainserviceunderthiswarrantyyoumust obtain a Returned Material Authorization (RMA) number from Tripp Lite or an authorized Tripp Lite service center. ProductsmustbereturnedtoTrippLiteoranauthorizedTrippLiteservicecenterwithtransportationchargesprepaid andmustbeaccompaniedbyabriefdescriptionoftheproblemencounteredandproofofdateandplaceofpurchase.This warrantydoesnotapplytoequipmentwhichhasbeendamagedbyaccident,negligenceormisapplicationorhasbeen altered or modified in any way. This warranty applies only to the original purchaser who must have properly registered the product within 10 days of purchase.

EXCEPT AS PROVIDED HEREIN, TRIPP LITE MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Somestatesdonot permit limitation or exclusion of implied warranties; therefore, the aforesaid limitation(s) or exclusion(s) may not applytothepurchaser.

EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL TRIPP LITE BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Specifically,TrippLiteisnotliableforanycosts, such as lost profits or revenue, loss of equipment, loss of use of equipment, loss of software, loss of data, costs of substitutes, claims by third parties, or otherwise.

+ 2 hidden pages