TRENDnet Super G Access Point User Manual

Size:
791.31 Kb
Download

TEW-450APB

Super G Access Point Quick Installation Guide

Point d'accès Super G Guide d'installation rapide

Super G Access Point Kurzanleitung zur Installation

Punto de Acceso Súper G Guía de instalación rápida

Точка доступа Super G Руководство по быстрой установке

Version 06.28.2005

TRENDnet

TRENDware, USA

What's Next in Networking

Copyright ©2005. All Rights Reserved. TRENDware International, Inc.

Table of Contents

 

English ......................................................................................................

1

1.

Prepare for Installation ......................................................................

1

2.

Install Hardware ................................................................................

2

3.

Configure TCP/IP Settings ................................................................

3

4.

Configure the Access Point ...............................................................

5

Troubleshooting...........................................................................................

10

English QIG

1. Prepare for Installation

Thank you for purchasing TRENDnet's TEW-450APBSuper G Access Point

This guide will help you set-upyour Access Point quickly and easily. Just follow thestep-by-stepinstructions below, and enjoy the benefits of accessing the Internet without ever being tied down to wires! If you run into problems, please refer to the Troubleshooting section. If you need further technical support, please visit www.TRENDNET.com or call technical support by phone.

Verify Package Contents

Please make sure you have everything in the box:

 

 

 

TEW-450APB

 

CD-ROM(User’s Guide)

 

 

 

 

 

 

 

 

 

 

 

 

 

TEW-450APB

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TRENDnet

 

 

 

 

 

 

 

Quick Installation Guide

 

External Power Adapter

 

1.5M RJ-45cable

Verify Equipment

Before setting up the Access Point, you should have:

1.A Computer with a Wired (RJ-45)or Wireless network card.

2.TCP/IP protocol installed on the Computer.

3.A Web Browser such as Internet Explorer (5.0 or higher) or Netscape Navigator (4.7 or higher).

4.A Hub or Switch connecting your existing wired network.

5.An RJ-45Network Cable for connecting the Access Point to your network Switch.

1

English

2.Install Hardware

1.Locate an optimum location for the Access Point. The best place for the Access Point is usually at the center of your wireless network.

2.Connect the RJ-45network cable to the Access Point, then connect the other end of the network cable to a Switch or Hub. The Access Point is now connected to your 10/100Mbps network.

3.Connect the power adapter to the Access Point. Make sure you use the

power adapter supplied with the Access Point; using a different power adapter may damage the unit.

TEW-450APB

2 3

NOTE: If you are using a wired computer to configure the Access Point, please connect this computer to the same Switch or Hub theTEW-450APBis connected to.

LAN

POWER

WLAN

Verify Hardware Installation

Make sure the front panel lights are on: Power, LAN, WLAN.

2

English

3. Configure TCP/IP Settings

Before the Access Point can be accessed and configured, the computer's TCP/IP settings need to be changed. (That includes your wireless card's IP address, too.)

Windows 2000/XP

1.Find the Start button located on the Desktop.

2.Click Start, and click onControl Panel. For Windows 2000, click Start, highlight Settings, and clickControl Panel.

3.Double-ClicktheNetwork Connection icon.

4.Right-Clickon theLocal Area Connection icon, then click onProperties. The Local Area Connection Properties box will appear.

5.Under the General tab, locate and selectInternet Protocol TCP/IP and then clickProperties. The Internet Protocol (TCP/IP) Properties box will appear.

3

English

6.Click on Use the following IP address.Enter 192.168.1.50 for IP address and 255.255.255.0 for Subnet, then click OK.

7. Click OK.

8. Your computer is now ready to access and configure the Access Point.

4

English

4. Configure the Access Point

From a Wired Computer

1.Open a web browser (Internet Explorer or Netscape) and enter http://192.168.1.1 at the address bar, then press the Enter key. Typeadmin forusername, and typeadmin for yourpassword. ClickOK.

2. Click Wizard.

5

English

3. Click Next.

4.If you want to change the default password, type in a new password and click Next. Otherwise, clickNext.

6

English

5.If you want to change the default SSID or channel, type in the appropriate information and click Next. Otherwise, clickNext.

6. Click Next.

7

English

7. ClickRestart and clickClose.

Congratulations!

Installation is now complete.

From a Wireless Computer

(using TRENDnet's TEW-441PCas an example in this section)

The default settings of the Access Point are:

SSID - AP254f02

Channel - 6

8. On your wireless computer, open up your Wireless Utility Program.

8

English