TRENDnet HS-6038 User Manual

Size:
3.16 Mb
Download

HS-6038

Socket 370 133MHz FSB

Industrial Single Board Computer

Full-sizeAll-in-OneCompactFlash

133MHz FSBCRTDual LANAudio

ATA/33/66/100RS-232/422/485PC/104

IrDAUSBDOCWDTH/W Monitor

PICMG Bus Industrial Single Board Computer

Copyright Disclaimers

The accuracy of contents in this manual has passed thorough checking and review before publishing. BOSER Technology Co., Ltd., the manufacturer and publisher, is

not liable for any infringements of patents or other rights resulting from its use. The manufacturer will not be responsible for any direct, indirect, special, incidental or consequential damages arising from the use of this product or documentation, even if advised of the possibility of such damage(s).

This manual is copyrighted and BOSER Technology Co., Ltd. reserves all documentation rights. Unauthorized reproduction, transmission, translation, and storage of any form and means (i.e., electronic, mechanical, photocopying,

recording) of this document, in whole or partly, is prohibited, unless granted permission by BOSER Technology Co., Ltd.

BOSER Technology Co., Ltd. reserves the right to change or improve the contents of this document without due notice.BOSER Technology Co., Ltd. assumes no responsibility for any errors or omissions that may appear in this manual, nor does it make any commitment to update the information contained herein.

Trademarks

BOSER is a registered trademark of BOSER Technology Co., Ltd. ISB is a registered trademark of BOSER Technology Co., Ltd. Intel is a registered trademark of Intel Corporation.

AMI is a registered trademark of American Megatrends, Inc. Award is a registered trademark of Award Software, Inc.

All other trademarks, products and or product names mentioned herein are mentioned for identification purposes only, and may be trademarks and/or registered trademarks of their respective companies or owners.

©Copyright 2004 BOSER Technology Co.,Ltd. All Rights Reserved.

Version 1.0, May 06, 2004

Table of Contents

Chapter 1 General Description…………………...1

1.1

Major Features..................................................................

2

1.2

Specifications ...................................................................

3

1.3

Board Dimensions............................................................

4

Chapter 2 Unpacking……………………………..5

2.1

Opening the Delivery Package........................................

5

2.2

Inspection..........................................................................

5

Chapter 3 Hardware Installation………………...7

3.1

Before Installation ............................................................

7

3.2

Board Layout ....................................................................

8

3.3

Jumper List .......................................................................

9

3.4

Connector List ..................................................................

9

3.5

Configuring the CPU ......................................................

10

3.6

System Memory..............................................................

10

3.7

VGA Controller ...............................................................

10

3.8

IDE Drive Connector ......................................................

11

3.9

Floppy Disk Drive Connector ........................................

12

3.10

Serial Port Connectors ..................................................

12

3.11

Parallel Connector..........................................................

13

3.12

Ethernet Connector........................................................

14

3.13

IrDA Connector...............................................................

14

3.14

USB Connector...............................................................

15

3.15

CMOS Data Clear............................................................

15

3.16

Power and Fan Connectors...........................................

16

3.17

Keyboard/Mouse Connectors .......................................

17

3.18

System Front Panel Connectors...................................

17

3.19

External Speaker ............................................................

18

3.20

Thermal Input Connectors.............................................

18

3.21

Audio Connectors ..........................................................

19

3.22

SMI Signal Input Switch.................................................

19

3.23

Watchdog Timer .............................................................

20

3.24

CompactFlash Connector...........................................

21

3.25

PC/104 Connectors ........................................................

22

3.26

DiskOnChip Address Setting .....................................

25

Chapter 4 AMI BIOS Setup……………………..27

4.1

Starting Setup.................................................................

27

4.2

Using Setup.....................................................................

28

4.3

Main Menu .......................................................................

29

4.4

Standard CMOS Setup ...................................................

30

4.5

Advanced CMOS Setup .................................................

31

4.6

Advanced Chipset Setup ...............................................

32

4.7

Power Management Setup ............................................

33

4.8

PCI / Plug and Play Setup..............................................

34

4.9

Peripheral Setup.............................................................

35

4.10

Hardware Monitor Setup................................................

36

4.11

Auto-DetectHard Disks .................................................

37

4.12

Change Supervisor/User Password .............................

38

4.13

Auto Configuration with Optimal Settings ..................

39

4.14

Optimal Configuration with Fail Safe Settings............

40

4.15

Save Settings and Exit...................................................

41

4.16

Exit Without Saving........................................................

42

Chapter 5 Software Utilities…………………….43

5.1

IDE Driver Installation ....................................................

43

5.2

VGA Driver Installation ..................................................

49

5.3

LAN Driver Installation...................................................

55

5.4

Audio Driver Installation................................................

74

Safety Instructions

Integrated circuits on computer boards are sensitive to static electricity. To avoid damaging chips from electrostatic discharge, observe the following precautions:

Do not remove boards or integrated circuits from their anti-staticpackaging until you are ready to install them.

Before handling a board or integrated circuit, touch an unpainted portion of the system unit chassis for a few seconds. This helps to discharge any static electricity on your body.

Wear a wrist-groundingstrap, available from most electronic component stores, when handling boards and components. Fasten the ALLIGATOR clip of the strap to the end of the shielded wire lead from a grounded object. Please wear and connect the strap before handle theHS-6038to ensure harmlessly discharge any static electricity through the strap.

Please use an anti-staticpad when putting down any components or parts or tools outside the computer. You may also use ananti-staticbag instead of the pad. Please inquire from your local supplier for additional assistance in finding the necessaryanti-staticgadgets.

NOTE: DO NOT TOUCH THE BOARD OR ANY OTHER SENSITIVE COMPONENTS WITHOUT ALL NECESSARYANTI-STATICPROTECTION.

Chapter 1

General Description

The HS-6038is a 133MHz FSB Intel® 82815/82801BAchipset-basedboard designed for PICMG Bus Celeron™/Coppermine™/Tualatin™ 800MHz~1.2GHz CPU compatibility. These features combine and make theHS-6038an idealall-in-oneindustrial single board computer. Additional features include an enhanced I/O with CompactFlash, VGA, dual LAN, audio, and two COM interfaces.

Its onboard ATA/33/66/100 to connected IDE drive interface architecture allows the HS-6038to support data transfers of 33, 66 or 100MB/sec. for each IDE drive connection. Designed with the Intel® 82815/82801BA core logic chipset, the board supports all Celeron™/Coppermine™/Tualatin™ CPU series operating at 800MHz to 1.2GHz. The 82815 integrated CRT display controller supports up to 1280 x 1024 at 16 color resolution.

A single Flash chip holds the system BIOS, and you can change the Flash BIOS by the Utility Update. Advanced IrDA port also provides a faster data transmission. You can also use the DOS version of the “DiskOnChipTM” socket by issuing commands from the DOS prompt without the necessity of other software supports up to 288MB. System memory is also sufficient with the two DIMM sockets that can support up to 512MB.

1

Additional onboard connectors include an advanced USB and IrDA ports providing faster data transmission, and a dual RJ-45connector for 10/100 Based Ethernet use.

To ensure the reliability in an unmanned or standalone system, the Watchdog Timer (WDT) onboardHS-6038is designed with pure hardware that does not need the arithmetical functions of areal-timeclock chip. If any program causes unexpected halts to the system, the onboard Watchdog Timer (WDT) will automatically reset the CPU or generate an interrupt to resolve such condition.

The HS-6038also has a CompactFlashTM connector that accommodates standard of memory cards available in the market.

1.1Major Features

The HS-6038comes with the following features:

Socket 370 for Intel® Celeron /Coppermine /Tualatin 800MHz ~1.2GHz CPU

Supports 66/100/133MHz FSB

Two DIMM sockets with a max. capacity of 512MB Intel® 82815/82801BA system chipset

Winbond W83627 super I/O chipset Intel 82815 CRT display controller

Intel 82559 and ICHII 10/100 Based LAN AC97 3D audio controller

Two COM, four USB connectors PC/104 Bus connector

DiskOnChipTM socket supporting memory sizes of up to 288MB Supports Hardware Monitor

Supports CompactFlashTM card reader (optional)

2

1.2Specifications

CPU: Socket 370 for Intel Celeron /Coppermine /Tualatin 800MHz ~1.2GHz CPU

Bus Interface: PICMG Bus

Memory: Two DIMM sockets supporting up to 512MBChipset: Intel® 82815/82801BA

I/O Chipset: Winbond W83627

CompactFlash : One, IDE interface adapter (optional)

VGA: Intel 82815 supporting CRT display up to 1280 x 1024 at 16 colorsLAN: Intel® 82559 and Intel® ICHII 10/100 Based LAN

Audio: AC97 3D audio controller

IDE: Four IDE disk drives supporting ATA/33/66/100 and with transfer rates of up to 33/66/100MB/sec.

FDD: Supports up to two floppy disk drives

Parallel: One enhancedbi-directionalparallel port supporting SPP/ECP/EPP

Serial Port: 16C550UART-compatibleRS-232/422/485x 1 andRS-232x 1 serial ports with16-byteFIFO

PC/104: PC/104 connector for8-bitISA BusIrDA: One TX/RX IrDA header

USB: Four USB connectorsKeyboard/Mouse: PS/26-pinMini DIN

DiskOnChip: DiskOnChip socket supporting memory sizes of up to 288MB

BIOS: AMI PnP Flash BIOS

Watchdog Timer: Software programmabletime-outintervals from 1~256 sec.

CMOS: Battery backup

Power Consumption: +5V/7.5A (1GHz CPU), +12V/120mA

Operating Temperature: 0~60°C Hardware Monitor:Winbond W83627

Board Size: 33.8 x 12.1 cm

3

1.3Board Dimensions

4