TRENDnet Dual-Band 802.11 a+g Wireless Reuter User Manual

Size:
788.69 Kb
Download

TEW-511BRP

Dual-Band802.11 a+g Wireless Router Quick Installation Guide

Guide d'installation rapide du

Routeur sans fil 802.11 a+g Dual band

Anleitung zur Schnellinstallation des

Drahtloser 802.11 a+g Dualband-Router

Guía de Instalación Rápida

Enrutador inalámbrico a+g 802.11 de Banda-Dual

Маршрутизатор для беспроводной связи Dual-Band802.11 a+g

Руководство по быстрой установке

Version 04.28.05

TRENDnet

TRENDware, USA

What's Next in Networking

Copyright ©2005. All Rights Reserved. TRENDware International, Inc.

Table of Contents

 

English ...................................................................................................................

1

1.

Prepare for Installation ...................................................................................

1

2.

Install Hardware .............................................................................................

3

3.

Configure the computer's TCP/IP Settings .....................................................

4

4.

Configure your AP/Router ..............................................................................

8

5.

Wireless Configuration ..................................................................................

12

6. Test your Connection .....................................................................................

14

Troubleshooting ......................................................................................................

16

English QIG

1. Prepare for Installation

Thank you for purchasing the TEW-511BRP.This Wireless AP/Router will allow you to securely share your Internet connection, files, and other resources with multiple users.

This guide will help you set up and configure your AP/Router. Following the installation instructions should be quick and easy. If you run into problems, please refer to the Troubleshooting section or the more detailed installation procedures on the User's Guide CD-ROM.If you need further technical support, please visit www.TRENDNET.com or call technical support by phone.

Verify Package Contents

Please make sure you have everything in the box:

 

 

 

TEW-511BRP

 

User’s Guide CD-ROM

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TEW-511BRP

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TRENDnet

 

 

 

 

 

 

 

Quick Installation Guide

 

AC Power Adapter (5V, 2.5A)

 

RJ-45Ethernet (LAN) Cable

Verify Equipment

Before installing the AP/Router, you should have:

1.An installed Cable/DSL Modem with an Ethernet Port

2.A Broadband Internet Account

3.A web browser such as Internet Explorer (5.0 or higher) or Netscape Navigator (4.7 or higher)

4.A network cable for each computer

5.A computer with the TCP/IP Protocol and Client for Microsoft Networks Service installed

1

English

Collect Account Information from Internet

Service Provider (ISP)

During the installation of your AP/Router, the configuration utility will ask you to specify your ISP connection type. Therefore, please verify your Cable or DSL Internet broadband connection with your ISP and ensure you have all the information for one of the following connection types:

Dynamic IP Cable Connection

Nothing is required. The IP address will be automatically be assigned by your ISP.

Static or Fixed IP Cable Connection

Internet IP Address:____.____.____.____ (eg. 215.24.24.129) Subnet Mask: ____. ____. ____. _____

Gateway IP Address:____.____.____._____

Primary DNS:____.____._____.______

Secondary DNS:_____._____._____.____

PPPoE Connection

Login Name:______________

Password:________________

PPTP DSL Connection

Internet IP Address:____.____.____.____ (eg. 215.24.24.129) Subnet Mask: ____.____.____._____

Gateway IP Address:____.____.____._____

PPTP Server IP:____.____._____._____

Login Name:_______________

Password:_________________

2

English

2.Install Hardware

1.Connect one RJ-45network cable from the Cable/DSL Modem's Ethernet port to the WAN port on the AP/Router.

2.Connect a different RJ-45network cable from one of the AP/Router's LAN ports to your computer's network port.

3.Turn on your Cable/DSL modem.

4.Connect the included Power Adapter to your AP/Router and to your power outlet; your AP/Router should turn on.

5.Turn on your computer

POWER

1

4

2

Verify Hardware Installation

Verify that the following front panel lights are on: Power, Internet, and one LAN port LED for each wired computer connected to the AP/Router.

LAN

POWER

INTERNET

NOTE: Due to European Wireless Regulations, Super A Mode is not supported in the EU version.

3 English

3. Configure the computer's TCP/IP Settings

Windows 2000/XP

1.Click Start; clickSettings and click onControl Panel

2.Double-ClicktheNetwork Connections icon.

3.Right-Clickon theLocal Area Connection icon, and then click onProperties. The Local Area Connection Properties box will appear.

4.Under the General Configuration Tab, locate and selectTCP/IP, then clickProperties. The Internet Protocol (TCP/IP) Properties box will appear.

NOTE: If you have a Fixed IP address connection, write down the existing IP addresses from the following sections before you make any changes.

5.Click on Obtain an IP address automaticallyand Obtain DNS Server address automatically.

4

English

6.Click OK.

7.Click Close on the Local Area Connection Properties box.

8.Click Start; click onRun. Then typecmd and clickOK.

9.The Command Prompt window will appear. Type ipconfig at the C:\ prompt and press theEnter key.

10.If your IP Configuration reads as follows, your computer is successfully connected to the router:

IP Address: 192.168.1.x (x= any number from 2~255) Subnet Mask: 255.255.255.0

Default Gateway: 192.168.1.1

NOTE: If your IP Configuration does not match the values above, please restart your computer and retry the steps in this section.

5

English

Windows 95/98/SE/ME

1.Click Start;clickSettings and then click onControl Panel.

2.Double-Clickthe Network icon and the Network Properties box will appear.

3.Under the Configuration Tab, locate and selectTCP/IP with the corresponding network card (such as TRENDnetTE100-PCIWN10/100Mbps Network Adapter), then click on theProperties button.

4.Under the IP Address Tab, click on the Obtain an IP address automatically option.

5.Click OK on the TCP/IP Properties box.

6.Click OK on the Network Box.

7.At this point, the installation may require files from your Windows CD-ROM.If this happens, insert your WindowsCD-ROMinto yourCD-ROMdrive and selectCD-ROM drive to load the files.

6

English

8. After the files load, theSystem Settings Change will appear, clickYes to reboot your system. This will update your computer with the new settings.

NOTE: If the message does not appear, you need to manually restart your computer.

9.After your system reboots, click Start and click onRun. Then typewinipcfg in the field and then clickOK.

10.The IP configuration box will appear. Choose your network adapter from the dropdown box, and the utility will display your computer's current IP address information.

11.If your IP Address reads as follows, your computer is successfully connected to the router:

IP Address: 192.168.1.x (x= any number from 2~255) Subnet Mask: 255.255.255.0

Default Gateway: 192.168.1.1

NOTE: If your IP configuration does not match the values above, please restart your computer and retry the steps in this section.

7

English

4. Configure your AP/Router

The following section will help you configure your AP/Router to connect to the Internet and your PCs. The setup differs and is dependent on the type of Internet connection you have. If you are not sure what type of connection you have, please contact your ISP to obtain the required information, which is listed in the Prepare for Installation section at the beginning of this Quick Installation Guide.

1.Open your web browser, type http://192.168.1.1 in the Address bar, and pressEnter.

2.An authentication window will appear. Enter the username and password, and then click OK. By default, the username is blank, and the password is “admin.”

NOTE: To reset the password on the AP/Router, refer to the User's GuideCD-ROM.

8

English