TRENDnet Bridge TEW640MB User Manual

Size:
5.22 Mb
Download

Quick Installation Guide

TEW-640MB

1.01

Table of Contents

English

1

1.

Before You Start

1

2.

Hardware Installation

2

3.

Configure the TEW-640MB

3

4.

Wi-FiProtected Setup (WPS) Push Button Setup

7

Troubleshooting

9

Wireless Tips

12

Version 11.23.2010

1. Before You Start

Package Contents

ŸTEW-640MB

ŸCD-ROM(User's Guide)

ŸMulti-LanguageQuick Installation Guide

ŸPower Adapter (12V DC, 0.5A)

ŸNetwork Cable (0.6m/2ft.)

System Requirements

ŸA computer with network adapter installed

ŸWireless router (e.g.TEW-639GR)or access point (e.gTEW-690AP)

ŸAn available DHCP Server–wirelessrouters usually have abuilt-inDHCP server

ŸA media device (e.g. Game Console,Blu-rayplayer, Internet Ready TV, etc.) with an Ethernet port

ŸWeb Browser: Internet Explorer (6.0 or higher)

1

2. Hardware Installation

Note:

1:Wi-FiProtected Setup (WPS) allows you to quickly connect to your wireless router or access point. If you would like to use WPS push button setup, please go directly to section 4.Wi-FiProtected Setup (WPS) Push Button Setup. If your wireless router or access point does not support WPS, continue on to section 2 in the Hardware Installation.

2:Do not connect/install the TEW-640MBto your network until instructed to do so.

1.Connect one end of the provided RJ-45network cable to one of theTEW-640MB'sLAN ports. Connect the other end of the cable to your computer's network port.

2.Connect the Power Adapter to the TEW-640MBand then to a power outlet. EU Versions will have a power button on the back. Push the power button to the “On” position (EU Version). Wait 30 seconds for theTEW-640MBto boot up.

3.Verify that the following panel lights are on:

Wireless (Blue/Blinking)

Network Port (1-4)(Blue/Blinking)

Power (Blue/Solid)

2

3. Configure the TEW-640MB

1. Open your web browser, typehttp://tew-640mb.trendnetin the Address bar, and then pressEnter.

2.Enter the User Name and password and then click OK. Default Settings:

User name: admin

Password: admin

Note: User name and Password are case sensitive.

3. The Wizard will automatically appear. Click Administration Ž Wizard if the Wizard does not automatically appear.

4. Click Next.

5. Select Manual Setup and then clickNext.

3

6.Select DHCP to have the TEW-640MBautomatically obtain an IP address from your DHCP server (router). If Static IP address is selected you would need to configure the following:

IP address: The assigned IP address should be

similar to your network. This IP address should not be used by any other network device onyour network.

Subnet Mask: In most cases, the default

Subnet Mask (255.255.255.0) should be fine.

Default Gateway: Enter the IP address of your router for the Default Gateway.

Then click Next.

7. Click Scan.

8.Select a SSID and then click Select. The SSID is the wireless network name of your wireless network (e.g. wireless router or access point).

9. Click Next.

10.If Encryption is enabled on your wireless network (e.g. access point or wireless router) the correct Security Mode and Algorithm will be automatically selected. Enter the Pass Phrase (wireless network password) and then click Apply.

4

11. Verify that your settings are correct and then clickApply.

12. ClickOK.

13.Wait while your settings are being applied.

14.Click Export Setting (optional). This saves

your configuration settings in a file, which can be reloaded when needed.

15. ClickSave (optional).

16. Give the file a name, then clickSave.

5

17. Click Exit Wizard.

18.Unplug the power adapter and disconnect the TEW-640MBfrom your computer. Place theTEW-640MBin your desired location. Please

refer to the Wireless Tips section for optimal placement of the TEW-640MB.

19.Plug the power adapter of the TEW-640MBand connect one end of a network cable to one of theTEW-640MB'sLAN ports. Connect the other end of the cable to your media device's (e.g. Game Console,Blu-rayplayer, Internet Ready TV, etc.) network port. Verify that the following panel lights are on: Power (Blue/Blinking), Network Port(1-4)(Blue/Blinking), and Wireless (Blue/Blinking)

20.Verify that your network media device is

connected to your network. If the network setting on your media device is set to obtain an IP address automatically (dynamic IP) an IP address will be assigned automatically. Please refer to the manual or contact your media device's technical support for instructions.

Configuration is complete

For detailed information regarding the TEW-640MB’sconfiguration and advanced settings, please refer to the Troubleshooting section, User's Guide on the UtilityCD-ROM,or TRENDnet's website at http://www.trendnet.com.

Register Your Product

To ensure the highest level of customer service and support, please take a moment to register your product Online at: www.trendnet.com/register

Thank you for choosing TRENDnet

6

4. Wi-FiProtected Setup (WPS) Push Button Setup

Note:

1:Wi-FiProtected Setup (WPS) allows you to quickly connect to your wireless router or access point.

2:Do not connect/install the TEW-640MBto your network until instructed to do so. Make sure your network adapter settings are set to obtain an IP address automatically (see troubleshooting section).

1.Find a location where you would like to place the TEW-640MB.The location must be within the wireless coverage of your router or access point. Please refer to the wireless tips sections for additional information.

2.Connect the Power Adapter to the TEW-640MB

and then to a power outlet. EU Versions will have a power button on the back. Push the

power button to the “On” position (EU Version). Wait 30 seconds for the TEW-640MBto boot up.

3.Press and hold the WPS button on your wireless router or access point for 2 seconds. The example shows a TEW-690APaccess

point.

4.Within 60 seconds press and hold the WPS

button on the TEW-640MBfor 2 seconds. TheWPS button will start to blink.

5.Once the WPS button becomes steady blue (approximately within 120 seconds), the TEW-640MBhas been successfully configured.

7

6.Connect one end of a network cable to one of the TEW-640MB'sLAN ports. Connect the

other end of the network cable to your media device's (e.g. Game Console, Blu-rayplayer, Internet Ready TV, etc.) network port. Verify that the panel lights are on: Power (Blue/Blinking), Network Port(1-4)(Blue/Blinking), and Wireless (Blue/Blinking)

7.Verify that your network media device is connected to your network. If the network setting on your media device is set to obtain an IP address automatically (dynamic IP) an IP address will be assigned automatically. Please

refer to the manual or contact your media device's technical support for instructions.

Configuration is now complete.

8