TRENDnet 54Mbps 802.11g Wireless Router User Manual

Size:
1.27 Mb
Download

TEW-432BRP

54Mbps 802.11g Wireless Router Quick Installation Guide

Routeur sans file 802,11g 54Mbps

Guide d'installation rapide

Drahtloser 54 MBit/s 802.11g Router

Kurzanleitung zur Installation

Enrutador inalámbrico 802.11g a 54Mbps

Guía de instalación rápida

Маршрутизатор 54 Мбит/сек 802.11g Wireless

Руководство по быстрой установ

Version 07.15.05

TRENDnet

TRENDware, USA

What's Next in Networking

Copyright ©2005. All Rights Reserved. TRENDware International, Inc.

Table of Contents

 

English ...................................................................................................................

1

1.

Prepare for Installation ...................................................................................

1

2.

Install Hardware .............................................................................................

3

3.

Configure your AP/Router ..............................................................................

4

4.

Connect your Wireless Adapter to the Router ................................................

10

5. Test your Connection ....................................................................................

12

Troubleshooting ......................................................................................................

14

English QIG

1. Prepare for Installation

Thank you for purchasing the TEW-432BRP.This Wireless AP/Router will allow you to securely share your Internet connection, files, and other resources with multiple users.

This guide will help you set up and configure your AP/Router. Following the installation instructions should be quick and easy. If you run into problems, please refer to the Troubleshooting section or the more detailed installation procedures on the User's Guide CD-ROM.If you need further technical support, please visit www.TRENDNET.com or call technical support by phone.

Verify Package Contents

Please make sure you have everything in the box:

TEW-432BRP

User’s Guide CD-ROM

TEW-432BRP

TRENDnet

Quick Installation Guide

AC Power Adapter (5V, 2.5A)

Verify Equipment

Before installing the AP/Router, you should have:

1.An installed Cable/DSL Modem with an Ethernet Port

2.A Broadband Internet Account

3.A web browser such as Internet Explorer (5.0 or higher) or Netscape Navigator (4.7 or higher)

4.A network cable for each computer

5.A computer with TCP/IP Protocol and Client for Microsoft Networks Service installed

1

English

Collect Account Information from Internet

Service Provider (ISP)

During the installation of your AP/Router, the configuration utility will ask you to specify your ISP connection type. Therefore, please verify your Cable or DSL Internet broadband connection with your ISP and ensure you have all the information for one of the following connection types:

Dynamic IP Cable Connection

Nothing is required. The IP address will be automatically assigned by your ISP.

Static or Fixed IP Cable Connection

Internet IP Address:____.____.____.____ (eg. 215.24.24.129) Subnet Mask: ____. ____. ____. _____

Gateway IP Address:____.____.____._____

Primary DNS:____.____._____.______

Secondary DNS:_____._____._____.____

PPPoE DSL Connection

Login Name:______________

Password:________________

PPTP DSL Connection

Internet IP Address:____.____.____.____ (eg. 215.24.24.129)

Subnet Mask: ____.____.____._____

Gateway IP Address:____.____.____._____

PPTP Server IP:____.____._____._____

Login Name:_______________

Password:_________________

2

English

2.Install Hardware

1.Connect one RJ-45network cable from the Cable/DSL Modem's Ethernet port to the WAN port on the AP/Router.

2.Connect a different RJ-45network cable from one of the AP/Router's LAN ports to your computer's network port.

3.Turn on your Cable/DSL modem.

4.Connect the included Power Adapter from your AP/Router to a power outlet; your AP/Router should turn on.

5.Turn on your computer

TEW-432BRP

3

2

1

Verify Hardware Installation

Verify that the following front panel lights are on: Power, WAN, WLAN, and one LAN port LED for each wired computer connected to the AP/Router.

WLAN

SYSTEM

LAN

POWER

WAN

3

English

3. Configure your AP/Router

The following section will help you configure your AP/Router to connect to the Internet and your PCs. The setup differs and is dependent on the type of Internet connection you have. If you are not sure what type of connection you have, please contact your ISP to obtain the required information, which is listed in the Prepare for Installation section at the beginning of this Quick Installation Guide.

1.Open your web browser, type http://192.168.1.1 in the Address bar, and pressEnter.

2.An authentication window will appear. Enter the username and password, and then click OK. By default, the username is “admin”, and the password is “admin.”

NOTE: To reset the password on the AP/Router, refer to the User's GuideCD-ROM.

3. The “LAN Setting” page will appear. ClickWizard.

4

English

4. The “Wireless Router Setup Wizard” will appear. ClickNext.

5.If you want to change your password for your router, then type the new password in the Password and Verify Password fields. Click Next.

6. Choose the appropriate Time Zone from the pull down menu, and clickNext.

5

English

7.If you want to assign your router to a different network segment, then change the LAN IP Address andSubnet Mask. Make sure that theRange Start andRange End IP addresses match your network segment. Otherwise, clickNext.

8.Select your Connection Type from the pull down menu, (Obtain IP automatically, Fixed IP address, PPPoE, or PPTP) and proceed to the appropriate subset of instructions below.

Obtain IP automatically (DHCP client)

9.Select Obtain IP automatically (DHCP client)as the Connection Type and click Next.

10. Go to step 19.

6

English

Fixed IP Address

11. Select Fixed IP addressand click Next.

12.Enter the WAN IP Address, WAN Subnet Mask, WAN Gateway Address and DNS Server provided by your ISP and click Next.

13. Go to step 19.

PPPoE to obtain IP automatically

14.Select PPPoE to obtain IP automaticallyas the Connection Type and click Next.

7

English

15. Enter your username and password. ClickNext.

16. Go to step 19.

PPTP

17. SelectPPTP as the Connection Type and clickNext.

18.Enter the IP Address, Subnet Mask, Gateway, Server IP, PPTP Account, and PPTP Password. Click Next.

8

English