Toshiba TLP S70, TLP-S71, TLP-T71M User Manual

0 (0)

OWNER’S MANUAL

3LCD DATA PROJECTOR

TLP-T70M

(XGA)

TLP-T71M

(XGA / With Document Camera)

TLP-T60M

(XGA)

TLP-T61M

(XGA / With Document Camera)

TLP-S70

(SVGA)

TLP-S71

(SVGA / With Document Camera)

TLP-S40

(SVGA)

TLP-S41

(SVGA / With Document Camera)

Others Maintenance Operations Preparations Before Using

TLP-T70M / T60M / TLP-S70/TLP-S40

SAFETY PRECAUTIONS

WARNING:

WARNING:

USA only

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN THE CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY.

Handling the cord on this product or cords associated with accessories sold with this product, will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling.

FCC Radio Frequency Interference Statement

Note: This equipment has been tested and found to comply with the limits for a Class USA only A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiates radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the

interference at his own expense.

WARNING: USA only

Notice:

CANADA only

WARNING:

CAUTION:

Changes or modifications made to this equipment, not expressly approved by Toshiba, or parties authorized by Toshiba, could void the user’s authority to operate the equipment.

This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Laser beam is emitted when the laser button of the remote control is pressed. Do not look at the laser beam directly from the front of the remote control. Do not turn the laser beam toward a person or to a mirror.

IMPORTANT SAFETY INSTRUCTIONS

CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS

AND

Using

REFERENCE.

 

INSTRUCTIONS GIVEN IN THIS OWNER'S MANUAL AND THOSE

 

MARKED ON THE UNIT. RETAIN THIS BOOKLET FOR FUTURE

Before

This set has been designed and manufactured to assure personal safety. Improper use can

 

result in electric shock or fire hazard. The safeguards incorporated in this unit will protect you

 

if you observe the following procedures for installation, use and servicing. This unit is fully

 

transistorized and does not contain any parts that can be repaired by the user.

 

 

DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO

 

DANGEROUS VOLTAGE. REFER SERVICING TO QUALIFIED SERVICE

 

 

PERSONNEL ONLY.

1. Read Owner's Manual

3. Source of Light

After unpacking this product, read

Do not look into the lens while the

the owner's manual carefully, and

lamp is on. The strong light from

follow all the operating and other

the lamp may cause damage to

instructions.

your eyes or sight.

2. Power Sources

This product should be operated only from the type of power source indicated on the marking label.

If you are not sure of the type of power supply to your home, consult your product dealer or local power company.

For products intended to operate from battery power, or other sources, refer to the operating instructions.

4. Ventilation

Openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to.

2

3

IMPORTANT SAFETY INSTRUCTIONS (Continued)

5. Heat

8. Power-Cord Protection

The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

6. Water and Moisture

Do not use this product near water. - for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool and the like.

9. Overloading

Do not overload wall outlets; extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

7. Cleaning

Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a soft cloth for cleaning.

10. Lightning storms

For added protection for this product during storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage to the product due to lightning and power-line surges.

11. Object and Liquid Entry

Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

12. Do not place the product vertically

Do not use the product in the upright position to project the pictures at the ceiling, or any other vertical positions. It may fall down and dangerous.

14. Attachments

Do not use attachments not recommended by the product manufacturer as they may cause hazards.

15. Accessories

Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer's instructions, and should use a mounting accessory recommended by the manufacturer. A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.

Before Using

13. Stack Inhibited

Do not stack other equipment on

this product or do not place this

S3125A

product on the other equipment. Top and bottom plates of this product develops heat and may give some undesirable damage to other unit.

4

5

(Models equipped with

IMPORTANT SAFETY INSTRUCTIONS (Continued)

16. Damage Requiring Service

Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

a)When the power-supply cord or plug is damaged.

b)If liquid has been spilled, or objects have fallen into the product.

c)If the product has been exposed to rain or water.

d)If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation.

e)If the product has been dropped or damaged in any way.

f)When the product exhibits a distinct change in performance - this indicates a need for service.

18. Servicing

Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

19. Replacement Parts

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

(Replacement of the lamp only should be made by users.)

21.Do not leave thermalpaper documents or easily deformed items on top of the unit or near the air exhaust for long periods

of time.

The heat from the unit could erase the information on the thermal paper, or cause deformation or warping.

22.Do not get your hands between the camera arm and the main unit when setting the camera arm

back in its original position. (Models equipped with document camera)

To avoid injury, be careful not to get your hands caught when setting the camera arm back in its original position.

Families with children should be particularly careful.

17.If glass components, including lens and lamp, should break, contact your

dealer for repair service.

This product incorporates glass components, including a lens and a lamp. If such parts should break, please handle with care to avoid injury and contact your dealer for repair service. The broken pieces of glass may cause to injury. In the unlikely event of the lamp rupturing, thoroughly clean the area around the projector and discard any edible items placed in that area.

20. Safety Check

Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

23. Do not carry by the camera arm.

document camera)

Do not carry the projector by the camera arm. Doing so can result in damage or injury.

24. Do not move the projector while the arm is still erect.

(Models equipped with document camera)

Always store the arm back in position when moving the projector. Otherwise injury or damage may result.

Before Using

6

7

Toshiba TLP S70, TLP-S71, TLP-T71M User Manual

LABEL LOCATIONS

MODEL NO. /

RATING Label

WARNING Label

SERIAL NO. Label

MANUFACTURED;

SERIAL NO.

CAUTION Label

WARNING Label

CAUTION Label

CAUTION Label

CAUTION Label (LASER)

Remote Control

Y

PLA

INPUT

LASER WARNING

Models with Document Camera

CAUTION Label (LASER)

POWER SUPPLY CORD SELECTION

If your line voltage is 220 to 240V, use one of the following types of cable.

 

Using

Plug

 

Plug

 

configuration Plug type

Line voltage

configuration Plug type

Line voltage

 

EURO

220 – 240V

Australian

200 – 240V

Before

240V

 

 

 

 

 

 

 

 

 

10A

 

 

UK

220 – 240V

Switzerland

200 – 240V

 

240V

 

 

 

 

6A

 

 

Use a 5A fuse which is approved by ASTA

North American

200 – 240V

 

or BSI to BSI362.

 

 

Always replace the fuse cover after

240V

15A

changing the fuse.

 

IMPORTANT PRECAUTIONS

Save Original Packing Materials

The original shipping carton and packing materials will come in handy if you ever have to ship your LCD projector. For maximum protection, repack the set as it was originally packed at the factory.

Moisture Condensation

Never operate this unit immediately after moving it from a cold location to a warm location. When the unit is exposed to such a change in temperature, moisture may condense on the crucial internal parts. To prevent the unit from possible damage, do not use the unit for at least 2 hours when there is an extreme or sudden change in temperature.

Place and Manner of Installation

Do not place in hot locations, such as near heating equipment. Doing so could cause malfunction, and shorten the life of the LCD panel.

Avoid locations with oil or cigarette smoke. Doing so will dirty the LCD panel and other optical parts, shortening their lives, and darkening the screen.

Do not place slantwise in angle of 20° or more. Doing so could shorten the life of the lamp.

Using this instrument near a TV or radio may cause intereference to the images or audio sound. If this happens, move it away from the TV or radio.

Moving the projector from a low-temperature room to a high-temperature room may cause condensation on the lens or internal parts in the instrument. If you continue to use it in that situation, the malfunction may result. Ensure to wait until the condensation naturally disappears.

In a high altitude location where air is thin, cooling efficiency of the scanner is reduced so use it with the ambient temperature being lowered.

8

9

IMPORTANT PRECAUTIONS (Continued)

Avoid Volatile Liquid

Do not use volatile liquids, such as an insect spray, near the unit. Do not leave rubber or plastic products touching the unit for a long time. They will leave marks on the finish.

If cleaning with a chemically saturated cloth, be sure to follow the product's precautions.

LCD Panel

The life of the LCD panel is limited. Take care over the points below so as to use the panel for years.

To prolong the life of this panel, never fail to turn the power off when the panel is not in use and make sure that the lamp has gone out. The state of the lamp being extinguished helps enhance the effect of energy saving.

If the air filter is stained and is clogged up, the main unit inner temperature rises. As a result, the life of the LCD is shortened and a malfunction may also occur.

Clean the air filter from time to time and replace it regularly. It is recommended that this replacement be done at the time of replacing a lamp. (Ask a dealer where the unit was purchased or your nearby service station about an air filter for replacement.)

In the spaces provided below, record the Model and Serial No. located at the bottom of your LCD projector.

Model No.

Serial No.

Retain this information for future reference.

EXEMPTION CLAUSES

Toshiba Corporation bears no responsibility in the case of damages arising from natural disaster such as earthquakes, lightning, etc., fire not liable to Toshiba Corporation, operating by third parties, other accidents, or use under abnormal conditions including erroneous or improper operation and other problems.

Toshiba Corporation bears no responsibility for incidental damages (lost profit, work interruption, corruption or loss of the memory contents, etc.) arising from the use of or the inability to use this unit.

Toshiba Corporation accepts no liability whatsoever for any damages arising from not having followed the descriptions in this Instruction Manual.

Toshiba Corporation accepts no liability whatsoever for any damages arising from malfunctions arising from combination with equipment or software that is not related to Toshiba Corporation.

OTHER CAUTIONS AND INFORMATIONS

Copyrights

Showing or transmitting commercial imaging software or broadcast or cable-broad casting programs with the purpose of other than the personal and private viewing, including modifying images using the freeze or resize functions, or displaying with the varying aspect ratio of the images, could violate the direct or indirect copyrights of the imaging software or broadcast program, etc., if done without first consulting with the copyright holder. For this reason, please take appropriate measures before performing one of the actions listed above, including obtaining a license from the copyright holder.

Disposal

This product contains substances which are harmful to humans and the environment.

Solder used in the internal parts contains the lead.

The lamp contains inorganic mercury.

Please dispose of this product or used lamps in accordance with local regulations.

Trademarks

VGA, SVGA, XGA, SXGA, UXGA are trademarks or registered trademarks of International Business Machines Corporation.

Macintosh is a registered trademark of Apple Computer, Inc.

Windows is a registered trademark of Microsoft Corporation in the U.S. and other countries.

Adobe is a registered trademark and Acrobat Reader is a trademark of Adobe Systems Incorporated.

Notational Conventions Used in This Manual

References to pages with related information are annotated as follows. For example, if making a reference to page 36: p.36

Before Using

10

11

CONTENTS

Before Using

 

SAFETY PRECAUTIONS ................................................................................

2

IMPORTANT SAFETY INSTRUCTIONS .........................................................

3

LABEL LOCATIONS ........................................................................................

8

POWER SUPPLY CORD SELECTION ............................................................

9

IMPORTANT PRECAUTIONS .........................................................................

9

EXEMPTION CLAUSES ................................................................................

11

OTHER CAUTIONS AND INFORMATIONS ..................................................

11

CONTENTS ...................................................................................................

12

Preparations

 

Checking the package contents .....................................................................

14

Names of each part on the main unit .............................................................

15

Names of each part on the control panel and remote control ........................

16

Names of each part on the document camera

 

(models with a document camera) .................................................................

17

Preparing and using the remote control .........................................................

18

Placement ......................................................................................................

19

Connection .....................................................................................................

21

Mainenance

 

Air filter cleaning ............................................................................................

39

Lens and main unit cleaning ..........................................................................

40

Lamp replacement .........................................................................................

40

Others

 

Trouble indications .........................................................................................

42

Before calling service personnel ....................................................................

43

Specifications .................................................................................................

45

List of general specifications ......................................................................

45

Document camera specifications

 

(Models equipped with document camera) ................................................

45

List of supported signals (RGB signals) .....................................................

46

List of supported signals (Y/PB/PR signals) ................................................

47

List of supported signals (Video, S-Video signals) .....................................

47

Pin assignment of COMPUTER & MONITOR terminals ............................

47

CONTROL terminal ....................................................................................

48

Separately Sold Product .............................................................................

48

Operations

 

Turning the power on and off .........................................................................

22

Basic operations ............................................................................................

24

Using handy features .....................................................................................

26

Using auto setting (Auto setting) ................................................................

26

Correcting the keystone distortion (Keystone) ............................................

27

Zooming out the images .............................................................................

27

Cutting off the picture and sound temporarily (Mute) .................................

28

Freezing the image (Freeze) ......................................................................

28

Enlarging the picture size (Resize) .............................................................

29

Displaying Information [Status display] .......................................................

30

Using the menus ............................................................................................

31

How to use the menus ................................................................................

31

The image adjustment menu ......................................................................

32

The default setting menu ............................................................................

32

The display setting menu ............................................................................

33

Reset menu (Special menu) .......................................................................

33

Using the document camera ..........................................................................

34

Uninstalling the camera ..............................................................................

34

Installing the camera ..................................................................................

34

Preparation of the document camera (when loading the camera) ..............

35

Preparing the document camera

 

(for use being separated from the projector) ..............................................

35

Image projection with the document camera ..............................................

36

Locking the white balance ..........................................................................

38

Before Using

12

13

Checking the package contents

Please make sure that the following items are included in the box, along with the main unit. If any item is missing, please contact the store immediately where you purchased the product.

(1) (6) (11)

(2)

(7)

(*1)

(12)

 

 

(3)

(8)

 

 

(4)

(9)

(13)

 

 

(*2)

(5)

(10)

 

 

 

/

 

 

-

(1) Remote control

(2) R03 (SIZE AAA) batteries for remote control (2)

(3) CD-ROM

(4) Owner’s Manual

(5) Power cord (See note)

(6) RGB cable

(7) Quick Reference(*1)

(8) Video cable(*1)

(9) Audio cable (for computer)(*1)

(10) Audio cable(*1)

(*1) Not supplied for TLP-S70,TLP-S71.

Note

■ (11) Camera extension cable

(supplied with the document camera)

(12) Carrying bag

(13) Mouse remote control set (*2)

Mouse remote control

R03 (SIZE AAA) batteries for mouse remote control (2)

Mouse remote control receiver

Mouse remote control manual (*2)Supplied with TLP-T60M, TLP-T61M,

TLP-T70M, TLP-T71M

The shape and number of supplied power cords vary depending on the product destination.

The Supplied CD-ROM

The supplied CD-ROM contains an owner’s manual, including information omitted in this Owner’s manual (Getting started) and Acrobat® Reader™ to view the manual.

Installing Acrobat® Reader™

Windows®: Run the CD-ROM, select the Reader/English folder, and run ar500enu.exe. Follow the on-screen instructions.

Macintosh: Run the CD-ROM, select the Reader/English folder, and run Reader Installer. Follow the on-screen instructions to install the software.

Viewing the manual

Run the CD-ROM and double-click on Start.pdf. Acrobat® Reader™ launches, and the menu screen of the Owner’s manual appears. Click on your language. The Owner’s Manual cover and list of bookmarks appear. Click on a bookmark title to view that section of the manual. Click on p. to view a reference page with related information. See the Help menu for more information about Acrobat® Reader™.

Names of each part on the main unit

 

 

(5) (4)

(3) (2) (1)

(12)

 

(11)

 

 

 

(5)

 

 

 

 

 

 

(10)

 

 

(6)

 

 

 

(9)

 

 

 

 

 

 

 

 

(6)

(7)

(8)

 

(13)

(1) (14)(15)(16) (14)

 

 

 

 

(17)(18)(19)(20)(21)(22)

 

 

 

 

 

COMPUTER-

VIDEO

 

 

 

 

AUDIO MONITOR

( Y/P /P )

VIDEO S-VIDEO CONTROL

 

Name

: Function

(1)

Infrared remote sensor

: Senses commands from the remote control. p.18

(2)

Lens

: Projects expanded image.

(3)

Zooming lever

: Adjusts screen size. p.25

(4)

Focusing ring

: Adjusts screen focus. p.25

(5)

Air intake

: Draws in air from outside unit.

(6)

Tilt adjuster

: Adjusts the projector’s horizontal tilt. p.25

(7)

Lamp cover

: Remove to replace lamp. p.41

(8)

AC IN socket

: Connect the supplied power cord here. p.22

(9)

Foot adjuster

: Adjusts the vertical projection angle. p.25

(10)

Foot adjuster release button

: Press to stow the foot adjuster. p.25

(11)

Control panel

: Operates the projector. p.16

(12)

Camera input terminal*

: Connect the camera. p.34 p.35

(13)

Camera mounting stays*

: Hold the camera control panel. p.34

(14)

Air exhaust

: Expels air that has grown hot inside the projector.

(15)

Speaker

: Plays audio.

(16)

Anti-theft lock hole

: Attach a security chain, etc. here.

(17) AUDIO terminal

: Feeds the audio signal from a computer or video

 

 

equipment.

(18) MONITOR terminal

: Connected to the monitor display.

(19) COMPUTER terminal

: Feeds the RBG signal from a computer or the compo-

 

 

nent video signal (Y/PB/PR) from a video equipment.

(20) VIDEO terminal

: Feeds the video signal from a video equipment.

(21) S-VIDEO terminal

: Feeds the S-video signal from a video equipment.

(22) CONTROL terminal

: Connected to the RS-232C port on a controlling

 

 

computer for operating the projector. p.48

Note

*: For the models with a document camera

Preparations

14

15

Loading...
+ 18 hidden pages