Toshiba RD-XS52SU, RD-KX50SU, RD-XS52SC User Manual

0 (0)

DIGITAL VIDEO

HDD/DVD VIDEO RECORDER

RD-XS52SU RD-XS52SC RD-KX50SU

OWNER’S MANUAL

INSTALLATION

GUIDE

Read this booklet first.

Introduction

Connections

Setup Basic

P000411640

S PM0019288010 © 2004 Toshiba Corporation

Introduction

SAFETY PRECAUTIONS

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

AVIS

RISQUE DE CHOC ELECTRIQUE NE

PAS OUVRIR

WARNING : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USERSERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

The symbol for CLASS II (Double Insulation)

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE

 

TO RAIN OR MOISTURE. DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE

 

ENCLOSURE. DO NOT OPEN THE CABINET. REFER SERVICINGTO QUALIFIED PERSONNEL

 

ONLY.

CAUTION:

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY

 

INSERT.

ATTENTION:

POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA

 

FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

CAUTION:

This HDD/DVD video recorder employs a Laser System.

 

To ensure proper use of this product, please read this owner’s manual carefully and retain for

 

future reference. Should the unit require maintenance, contact an authorized service location -

 

see service procedure.

 

Use of controls or adjustments or performance of procedures other than those specified herein

 

may result in hazardous radiation exposure.

 

To prevent direct exposure to laser beam, do not try to open the enclosure.

 

Visible and invisible laser radiation when open and interlocks defeated.

 

DO NOT STARE INTO BEAM.

FCC NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rule. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

WARNING: Changes or modifications made to this equipment, not expressly approved by Toshiba, or parties authorized by Toshiba, could void the user’s authority to operate the equipment.

2

Note to cable system installer:

This reminder is provided to call the cable system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

The instructions shall state that an ALL-POLE MAINS SWITCH with a contact separation of at least 3 mm in each pole shall be incorporated in the electrical installation of the building.

CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

In the spaces provided below, record the Model and Serial No. located on the rear panel of your recorder.

Model No.

 

Serial No.

Retain this information for future reference.

Location of the required label

PRODUCT IS CERTIFIED BY THE MANUFACTURER TO

COMPLY WITH DHHS RULE 21 CFR SUBCHAPTER J

APPLICABLE AT THE DATE OF MANUFACTURE.

MANUFACTURED

1-1,SHIBAURA 1-CHOME,MINATO-KU,

TOKYO 105-8001,JAPAN

Introduction

Connections

Setup Basic

3

IMPORTANT SAFETY INSTRUCTIONS

1.Read these instructions.

2.Keep these instructions.

3.Heed all warnings.

4.Follow all instructions.

5.Do not use this apparatus near water.

6.Clean only with dry cloth.

7.Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8.Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9.Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11.Only use attachments/accessories specified by the manufacturer.

12.Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

S3125A

13.Unplug this apparatus during lightning storms or when unused for long periods of time.

14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

4

Introduction

ADDITIONAL SAFETY INSTRUCTIONS

15.When you use headphones, keep the volume at a moderate level. If you use the headphones continuously with high volume sound, it may cause hearing damage.

16.Do not overload wall outlets; extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

17.Apparatus should not be exposed to dripping or splashing and no objects filled with liquids, such as vases, should be placed on the apparatus.

18.Keep your fingers well clear of the disc tray as it is closing. Neglecting to do so may cause serious personal injury.

19.Do not place anything on top of this unit.

20.Do not place the apparatus on amplifiers or equipment that may produce heat.

21.Do not cover the ventilating holes for the inside cooling fan.

22.Do not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause serious personal injury and apparatus malfunction.

23.If the apparatus should smoke or smell, immediately disconnect the power cord from the wall outlet. Wait until the smoke or smell stops, then ask your dealer for a check and repair. Neglecting to do so may cause fire.

24.During thunderstor ms, do not touch the connecting cables or the apparatus.

25.The apparatus includes lead, an ingredient of solder used on the PCB, which is a harmful substance to human and the environment. When disposing of this apparatus, follow the rules and regulations in your area.

Introduction

Connections

Setup Basic

5

Introduction

Precautions

Notes on handling

Never disconnect the power cord from a wall outlet while the recorder is not in standby mode, unless it is in an emergency. Doing so may cause malfunction. When shipping the recorder, the original shipping carton and packing materials come in handy. For maximum protection, repack the unit as it was originally packed at the factory.

Do not use volatile liquids, such as insect spray, near the recorder. Do not leave rubber or plastic products in contact with the recorder for a long time. They will leave marks on the finish.

The top and rear panels of the recorder may become warm after a long period of use. This is not a malfunction.

When not in use

For usual absence

Be sure to remove the disc from the recorder and turn off the power.

Prolonged absence

Unplug the recorder from a wall outlet.

Notes on locating

Place the recorder on a level surface. Do not use it on a shaky or unstable surface such as a wobbly table or inclined stand. The loaded disc may dislodge from its proper position and cause damage to the recorder.

Before placing the recorder, make sure that the surface can stand the weight of the recorder. For safety, avoid placing the recorder in a high location, as an accidental fall of the recorder may cause personal injury.

When you place this recorder near a TV, radio, or VCR, the playback picture may become poor and the sound may be distorted depending on the condition and location of said equipment. In such an event, place the recorder as far away much as possible from the TV, radio, or VCR.

Do not install this product in an area where it will be exposed to large amounts of oily smoke, steam or dust, as such exposure could result in fire or electric shock. Cigarette smoke, dust etc. can cause the product to malfunction.

Notes on cleaning

Use a soft, dry cloth for cleaning.

Do not use any type of solvent, such as thinner or benzine, as they may damage the surface of the recorder.

Notes on antennas

Image and sound quality depend very much on signal reception.

Reception may be poor in weak signal areas. In this event, consult your dealer, or purchase a commercially available antenna booster. Refer to the booster’s instruction manual for installation details.

6

Notes on recording and editing

When you record/edit important content, make trial operations beforehand to confirm the recorder can function properly.

Toshiba does not compensate for content which was not recorded/edited because of some malfunction of this product or discs during operation, and is not liable for incidental damages (such as profit loss or interruption of business, etc.) produced in such conditions.

When the power cord is disconnected or when a power failure occurs during any operation of this product, all contents recorded in this recorder may be erased.

Depending on the channel or program, an excessive sound input level may cause noise or cut of recorded sound. Adjust the initial setting of the recording level when necessary.

If a program you have set a timer recording includes copy restriction signals, it may not be recorded. When programming a recording, confirm that a program you want to record is not copy-restricted.

Exemptions

Toshiba is not liable for any damage caused by fires, natural disaster (such as thunder, earthquake, etc.), acts by third parties, accidents, owner’s intentional or unintentional misuse, or uses in other improper conditions.

Toshiba is not liable for incidental damages (such as profit loss or interruption in business, modification or erasure of recorded data, etc.) caused by use or inability to use of this product.

Toshiba is not liable for any damage caused by neglect of the instructions described in the owner’s manual.

Toshiba is not liable for any damage caused by misuse or malfunction through simultaneous use of this product and the connected equipment or software that Toshiba is not concerned with.

Toshiba does not compensate for contents which were not recorded/edited because of some malfunctions of this product or discs during operation, and is not liable for incidental damages (such as profit loss or interruption in business, etc.) produced by such conditions.

Power Outage

After a power outage the clock display will flash. Set the clock to the correct time.

Notes on the unit and the HDD

Do not give a shock or shake (especially during operation).

Do not use in a shaky or unstable location.

Hold the unit horizontally.

Do not cover the ventilation holes for the cooling fan of the unit.

Do not use in a place where the temperature rises or changes rapidly.

Do not disconnect the power plug from a wall outlet while the unit is turned on.

Do not disconnect the power plug from the wall outlet or break the power supply to the unit during recording or playing. Before disconnecting the power plug, be sure to press the power button and make sure the unit ends the finishing process and power turns off completely. If the power plug is disconnected or power supply is disrupted while the unit is recording, all recorded content will be erased.

Toshiba is not liable for any damage or loss of recorded data caused by shock, shakes, misoperation or malfunction.

Introduction

Connections

Setup Basic

7

Introduction

Precautions (Continued)

Notes on moisture condensation

Moisture condensation damages the unit. Please read the following carefully.

Moisture condensation occurs, for example, when you pour a cold drink into a glass on a warm day. Drops of water form on the outside of the glass. In the same way, moisture may condense on the optical pick-up lens inside this unit, one of the most crucial internal parts of the unit.

 

 

le of m

 

 

 

mp

ois

tu

a

 

 

 

Ex

 

 

e

 

re

 

 

ond nsatio

n!

 

c

 

Optical pick-up lens

Moisture condensation occurs during the following cases.

When you bring the unit directly from a cold place to a warm place.

When you use the unit in a room where you just turned on the heater, or a place where the cold wind from the air conditioner directly hits the unit.

In summer, when you use the unit in a hot and humid place just after you move the unit from an air conditioned room.

When you use the unit in a humid place.

It’s too warm!

Do not use the unit when moisture condensation may occur.

If you use the unit in such a situation, it may damage discs and internal parts. Remove the disc, connect the power cord of the unit to the wall outlet, turn on the unit, and leave it for two or three hours. After two or three hours, the unit will have warmed up and evaporated any moisture. Keep the unit connected to the wall outlet and moisture condensation will seldom occur.

Wait!

Wall outlet

8

Program

Content is not

copyright

protected

Content is not copyright protected

Recording permitted once

Recording

 

Copy

 

 

 

 

DVD-RAM

Can be

HDD

Can be

disc

 

 

 

recorded

 

copied

DVD-R

 

DVD-RAM

 

 

 

disc

 

HDD

Can be

 

Can be

DVD-R

 

recorded

copied

 

 

 

 

DVD-RAM

 

HDD

 

disc

Can be

Cannot be

 

 

 

recorded

 

copied

DVD-R

 

DVD-RAM

 

HDD

Can be

disc

Cannot be

 

 

recorded

 

copied

 

Recording permitted once

DVD-R Cannot be

recorded

Recording permitted once

HDD

Cannot be recorded

Recording prohibited

DVD-RAM disc

Cannot be

recorded DVD-R

Recording prohibited

HDD:Hard Disc Drive

Content that can be recorded once can only move from the HDD to a DVD-RAM disc. (The original one is deleted after moving to a DVD-RAM disc.)

VCR Plus+, C3 and PlusCode are registered trademarks of Gemstar Development Corporation. The VCR Plus+ system is manufactured under license from Gemstar

Development Corporation.

Manufactured under license from QSound Labs, Inc.

U.S. patent Nos. 5,105,462, 5,208,860 and 5,440,638 and various foreign counterpart. Copyright QSound Labs,

Inc. 1998-2002. QXpanderTM is a trademark of QSound Labs, Inc. All rights reserved.

Introduction

Connections

Setup Basic

9

Toshiba RD-XS52SU, RD-KX50SU, RD-XS52SC User Manual

Introduction

Installation procedure

Read carefully “SAFETY PRECAUTIONS”, “IMPORTANT SAFETY INSTRUCTIONS” and “Precautions”.

( pages 2 to 9)

Check the supplied accessories. (See right)

Load the batteries in the remote control. ( page 18)

Connect an antenna to the recorder. ( page 20)

Connect a cable box or satellite system to the recorder. ( pages 22 to 25)

Connect the recorder to a TV. ( pages 20 to 21, 28)

Connect optional equipment to the recorder. ( page 29)

Make the initial settings. ( page 34)

Your recorder is ready. Read the separate volume “OPERATIONS GUIDE”.

Accessories

Remote control Batteries (AAA) x 2

Coaxial cable

Video/Audio cable

IR control cable

HDMI cable

Owner's manual (INSTALLATION GUIDE)

Owner's manual (OPERATIONS GUIDE)

Registration card

10

Introduction

About this product

Some differences

Because of its recording capacity and hard disc drive (HDD), this DVD recorder operates more like a computer and differently than a standard DVD player. In addition to containing a microprocessor, it contains a HDD, an operating system, random access memory (RAM), and a DVD-RAM/R drive. The operating system includes software stored on the HDD that is transferred to the RAM when the machine is turned on and at other times during operation. This transfer can take time. Therefore, when you turn the DVD recorder on, it may take a little while before it is ready to use. Likewise, other functions may not be performed as quickly as they would on other AV equipment. Additionally, because programs stored on the DVD-RAM/R drive cannot be accessed as quickly as those stored on the HDD, accessing those programs (or deleting a program from a DVD-RAM disc) may take more time. Please take these factors into consideration as you use the DVD recorder.

About the hard disc drive (HDD)

Like any HDD, the HDD in the DVD recorder is a fragile device that is susceptible to partial or complete failure if it is jarred or as a result of use over time. It will not last forever. Therefore, do not use the HDD for longer term storage of programs you wish to retain. [If portions of the HDD become damaged, programs recorded on those portions may exhibit pixelization or block noise when played back. Repeated playback of the program may cause the problem to get worse and, eventually, the program may become unplayable. Accordingly, if you notice such noise in a program that you want to save, you should transfer to a recordable DVD disc as soon as possible.] Recordable DVD discs are also susceptible to damage if not handled and stored carefully and some or all of the programs on them may become unplayable. You can reduce these risks by using high quality DVD recordable discs and checking their playability from time to time. If it becomes necessary to service your DVD recorder, it may be necessary to delete some or all of the programs on the HDD.

Playback Restrictions

This owner’s manual explains the basic instructions for this recorder. Some DVD video discs are produced in a manner that allows specific or limited operation during playback. As such, the recorder may not respond to all operating commands. This is not a defect in the recorder. Please refer to the notes on compatible discs later in this Introduction and to the discussion of DVD playback and features later in this manual.

” may appear on the TV screen during operation. “” means that the operation is not permitted by the recorder or the disc.

Recording Restrictions and Copyright

Copy-protected contents of DVD-Video discs, VIDEO CDs or audio CDs on the market cannot be copied on this recorder. Contents without copy protection should be copied or edited only in accordance with applicable copyright laws, which may restrict copying or editing.

Contents that permit single copying (copy once contents) can be recorded onto DVD-RAM discs, with some dubbing and editing restrictions. DVD-R discs cannot record these contents.

The unauthorized recording, use, distribution, or revision of copyrighted materials including, without limitation, television programs, videotapes, and DVDs, is prohibited under the Copyright Laws of the United States and other countries, and may subject you to civil and criminal liability.

Compatibility

In isolated cases, a disc bearing the DVD or CD logo may not fully and properly play back all features or as intended by the creator of the disc. This can be due, among other reasons, to problems and errors that can occur during the creation or recording of DVD and other software and the manufacture of software discs (including blank discs). Moreover, because of variations in the quality of discs, this recorder may not be able to record on all discs that bear a DVD-RAM or DVD-R logo, but you should not encounter difficulty if you use only high quality recordable DVD discs. Additionally, discs recorded in this device may not operate properly in other DVD players, recorders and/or personal computer drives. If you happen to encounter difficulties playing or recording a DVD disc or playing a CD disc, please feel free to call our Customer Service Hotline at 1-800-319-6684.

Introduction

Connections

Setup Basic

11

Introduction

Choosing a disc

When you want to play DVD or CD software or copy programs from the HDD to a recordable DVD, load an appropriate disc into the recorder. There are many types and formats of discs. Please use the following information to select an appropriate disc.

Notes

Handle the disc according to the disc instruction manual.

Toshiba cannot guarantee that all discs bearing the DVD or CD logos will operate as expected. Additionally, Toshiba cannot guarantee that discs recorded in this device will operate properly in other DVD players, recorders and/or personal computer drives.

For recording / playback

Disc

Mark

Specification

Remarks

DVD-RAM

 

• Single sided 4.7GB (12cm (43/4 in.))

Read carefully the section “On DVD-RAM

 

 

• Double sided 9.4GB (12cm (43/4 in.))

discs” ( page 14).

 

 

 

Select a DVD-RAM disc that shows a

 

 

 

statement on its package such as “this disc

 

 

 

can be used with video recorders and drives

 

 

 

compatible with 4.7GB DVD-RAM discs” or

 

 

 

“this disc can copy images that permit single

 

 

 

copying.”

 

 

 

 

DVD-R

 

• 4.7GB For General Ver.2.0

Read carefully the section “On DVD-R discs”

 

 

(12cm (43/4 in.))

( page 15).

 

 

 

Depending on the disc status or the

 

 

 

recording equipment, playback of the disc

 

 

 

may not be possible on this recorder.

 

 

 

 

Using different disc types for different purposes

DVD-RAM discs for your personal library

DVD-RAM discs comply with the global standard DVD-VR (Video Recording) format, and are optimized for recording of TV programs. You can rewrite repeatedly without deterioration of an image quality, erase unnecessary parts, divide a chapter, or specify playback area by frame. Its cartridge is suitable for a longer-term storage and family use, and its large capacity of 9.4 GB allows more recording space.

DVD-R discs when creating your own original discs for distribution

DVD-R discs are designed to comply with the global standard DVD-Video format, and can be recorded only once. DVD- R discs are convenient when you edit your original content (recorded personal events such as a wedding party) with this recorder, transfer them to the recorder and make copies to send to your friends or relatives. The discs can be played on other compatible DVD players.

*DVD-R may not be the best suited format for recording TV programs. Because of the way the discs are formatted, it may not be possible to edit or divide the program as you may prefer, to record secondary languages, or programs that are copy protected in a way that allows only one copy. (NOTE: “Copy once” protected programs generally can be recorded to DVD-RAM discs.)

*This recorder records on a DVD-R disc in DVD-Video format only.

*On DVD-R discs, direct recording, copying or the method “Creating a DVD-Video” ( page 122 in “OPERATIONS GUIDE”) are available.

We cannot guarantee that DVD-RAM/R discs recorded on this recorder will be playable on all DVD recorders/players. Similarly, there is no guarantee that all DVD-RAM/R discs recorded on other recorders will be playable on this recorder.

12

For playback only

Disc

Mark

Specification

Remarks

DVD video

• 12cm (43/4 in.) / 8cm (31/4 in.)

disc

• Region number 1 or ALL

 

• Color system: NTSC

The region number of this DVD recorder is 1. If region numbers, corresponding to a specific playable area, are printed on your DVD video disc and you do not find 1 or ALL , or the disc is encoded to permit playback only in regions other than Region 1, disc playback will not be allowed by the recorder.

VIDEO CD

 

• 12cm (43/4

in.) / 8cm (31/4

in.)

 

 

• Color system: NTSC

 

 

DIGITAL VIDEO

• Version 1.1 and 2.0

 

 

 

 

 

 

 

 

 

 

Audio CD

 

• 12cm (43/4

in.) / 8cm (31/4

in.)

Introduction

Connections

CD-R

• 12cm (43/4 in.)

Depending on the disc status, playback may

 

• CD-DA (audio CD) format

not be possible.

CD-RW

 

 

You cannot play discs other than those listed above.

You cannot play non-standardized discs even if they may be labeled as above.

You cannot play discs with specialized encoding (such as SACD discs) or the DVD audio portions of DVD Audio discs.

This recorder uses the NTSC color system, and cannot play DVD video discs recorded in any other color system

(PAL, SECAM, etc.), even if they have region marks 1 or ALL .

Toshiba cannot guarantee that all discs bearing the DVD or CD logos will operate as expected. Please see the discussion of compatibility on page 11.

Toshiba is not liable for any damage or loss caused directly or indirectly by the malfunction of this recorder, including, without limitation, any one of the following:

Failure to record contents intended to be recorded by the consumer.

Failure to edit contents as intended by the consumer.

When a DVD-RAM disc or a DVD-R disc created on this recorder is used (e.g., insertion, playback, recording or editing) in another DVD player, recorder or personal computer drive.

When a DVD-RAM disc or a DVD-R disc that is used in the manner described in the immediately preceding bullet point is used again in this recorder.

When a DVD-RAM disc or a DVD-R disc that was recorded in another DVD recorder, or in a personal computer drive is used in this recorder.

Some functions such as Library may not work with personal computer discs.

Discs recorded in this recorder may not operate as expected on other DVD players, recorders or personal computer drives.

Setup Basic

13

Introduction

Choosing a disc (Continued)

On DVD-RAM discs

Use only DVD-RAM discs that comply with DVDRAM standard Version 2.0 or 2.1.

The recorder cannot record on a disc formatted in any other standard. When using such a disc, initialize it by using the disc-format function of this recorder.

The recorder may not record, dub, or edit some DVDRAM discs, because they are edited/recorded with another manufacture’s equipment or PC, contain a large number of titles, or have little remaining capacity. Also, a DVD-RAM disc may not be edited or recorded if its title contains still pictures.

DVD-RAM discs formatted in UDF2.0 on a PC are not compatible with this recorder. Before using these discs, initialize them on this recorder.

This recorder complies with current copyright protection technology and can copy a disc only when the disc permits copying once. When there is no indication on the disc, copying will not be allowed. Such an indication on a disc is required also for the Library Management database.

DVD-RAM discs with cartridges are recommended for recording.

Two types of DVD-RAM discs are available: ones with cartridges and ones without cartridges. You can use either of

them with this recorder, but the former ones are recommended.

In order to record highly detailed data, make sure the disc is clean. DVD-RAM discs with cartridges are easier to handle in this regard.

Do not open the cartridge shutter. The disc may not play, or may not be recorded or edited once it becomes dirty.

There are two types of DVD-RAM cartridges; removable (TYPE 2/4) and not removable (TYPE 1). It is recommended you do not remove the disc even when you can.

Refer to the instruction manual that comes with the disc if it is absolutely necessary to remove the disc. Some commercially available cartridge discs cannot be recorded or edited once the inside discs are removed.

To protect recorded contents

Slide the write-protect tab to “PROTECT” with something small enough. The disc can play, but

cannot be edited or erased. Refer

PROTECT

to the instructions that come with the disc.

When using a disc without a cartridge (commercially

available discs)

Discs without cartridges can easily attract fingerprints and dust, which

is the reason they are not recommended. If you cannot avoid using them, handle with proper care.

When you write in a title column on a disc, use a pen with a soft tip. Do not use a pen with a hard tip, such as a ballpoint pen.

Recommended discs

The following discs have been tested with this recorder: 9.4 GB double-sided cartridge: Panasonic 2x

4.7 GB single-sided cartridge: Panasonic 2x

14

On DVD-R discs

Standards

DVD-R for General Ver.2.0 discs can be used for recording and playback.

Discs compatible with 2X speed recording (labeled Ver.2.0/2X etc.) and discs compatible with 4X speed recording (labeled Ver.2.0/4X etc.) can also be used. Select discs labeled “for video,” “for recording,” “120 min.” etc.

Recording conditions

Images for which copying is prohibited or restricted (copy once or copy prohibited) cannot be recorded. Even if the disc is labeled as CPRM compatible, this recorder can only be used to record copy-free material.

Recommended discs

That’s (Taiyo-Yuden) 1x, 4x

Tested discs

Panasonic 1x, 4x

Marks on DVD video discs

The following are examples of marks and the meanings.

Mark

Meanings

Number of audio streams 2 recorded in the disc.

(2 streams such as English and Japanese in this example.)

Number of subtitle languages

2recorded in the disc.

(2 subtitle languages are recorded in this example.)

Number of camera angles

3recorded in the disc.

(3 camera angles are recorded in this example.)

Pictures are recorded in the 4:3 standard picture shape

(4:3 aspect ratio).

Pictures are recorded in the letter LB box picture shape (4:3 aspect

ratio with horizontal black bars in the top and bottom of pictures).

Pictures are recorded in the 16:9 16:9 LB wide picture shape.

TVs with 4:3 aspect ratio will display them in the letter box style.

Pictures are recorded in the 16:9 16:9 PS wide picture shape.

TVs with 4:3 aspect ratio will display them in the pan scan style (one or both sides of pictures

are cut).

Actual picture shape may vary depending on the aspect ratio or mode selection of the TV.

Introduction

Connections

Setup Basic

15

Introduction

Choosing a disc (Continued)

Structure of disc contents

Normally, DVD video discs are divided into titles, and the titles are subdivided into chapters.

VIDEO CDs/audio CDs are divided into tracks.

DVD video disc

Title 1 Title 2

Chapter 1 Chapter 2 Chapter 1 Chapter 2 Chapter 3

VIDEO CD / audio CD

Track 1

Track 2

Track 3

Track 4

Track 5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Title: Divided contents of a DVD video disc. Roughly corresponds to a story title in short stories.

Chapter: Divided contents of a title. This corresponds to a chapter in a story.

Track: Divided contents of a VIDEO CD or an audio CD.

Each title, chapter, or track is assigned a number, which is called “title number”, “chapter number”, or “track number” respectively.

Some discs may not have these numbers.

When you record on the HDD or a DVD-RAM disc, one recording will always equal one title. You can divide a title into several chapters by marking borders in it to facilitate scene search.

On handling discs

Do not touch the playback side of the disc.

Yes

Playback side

Do not stick paper or tape to discs.

No

On cleaning discs

Fingerprints and dust on the disc cause picture and sound deterioration. Wipe the disc from the center outwards with a soft cloth. Always keep the disc clean.

Yes

No

Do not use any type of solvent such as thinner, benzine, commercially available cleaners or antistatic spray for vinyl LPs. It may damage the disc.

On storing discs

Do not store discs in a place subject to direct sunlight or near heat sources.

Do not store discs in places subject to moisture and dust such as a bathroom or near a humidifier. Store discs vertically in a case. Stacking or placing objects on discs outside of their case may cause warping.

16

Introduction

 

Table of Contents

 

Introduction

 

SAFETY PRECAUTIONS ......................................................................................................

2

IMPORTANT SAFETY INSTRUCTIONS ...............................................................................

4

Precautions ...........................................................................................................................

6

Installation procedure ........................................................................................................

10

About this product .............................................................................................................

11

Choosing a disc .................................................................................................................

12

Preparation of the remote control ....................................................................................

18

Connections

 

Connecting an antenna and TV .........................................................................................

20

Connecting to cable TV signal ..........................................................................................

22

Connecting to a satellite system ......................................................................................

24

Connecting the IR control cable .......................................................................................

25

Connecting to a TV with the HDMI terminal .....................................................................

26

Connecting to a TV equipped with component video inputs .........................................

28

Connecting to an audio system ........................................................................................

29

Basic Setup

 

Starting up the recorder ....................................................................................................

32

A: Initial settings ................................................................................................................

34

1: Language setting ...............................................................................................

36

2: Time and date setting ........................................................................................

37

3: Channel setting ..................................................................................................

40

4: Set top box setting .............................................................................................

42

5: Guide channel setting ........................................................................................

46

B: Output sound setting ....................................................................................................

48

C: TV shape setting ............................................................................................................

50

D: Remote control settings ...............................................................................................

52

Operating a TV with the remote control of this recorder ........................................

52

Operating the second and third TOSHIBA HDD/DVD video recorders with the

 

remote control of this recorder ..............................................................................

54

Limited Warranty DVD PLAYER/RECORDER ...................................................................

56

CANADIAN WARRANTY INFORMATION ..........................................................................

58

Introduction

Connections

Setup Basic

17

Introduction

Preparation of the remote control

1 Open the cover.

2 Insert batteries (AAA size).

Make sure to match the + and – on the batteries to the marks inside the battery compartment.

3 Close the cover.

Caution

• Never throw batteries into a fire.

Notes

Dispose of batteries in a designated disposal area.

Attention should be drawn to the environmental aspects of battery disposal.

Do not mix different battery types or combine used batteries with new ones.

If the remote control does not operate correctly, or if the operating range becomes reduced, replace both batteries with new ones.

If the batteries are dead or if you will not be using the remote control for a long time, remove the batteries to prevent battery acid from leaking into the battery compartment.

Operating with the remote control

Point the remote control at the remote sensor and press the buttons.

30° 30°

Within about 7 m (23 ft)

OPEN/CLOSE

 

TV

 

 

TV /VIDEO

CH

VOLUME

CH

HDD

TIMESLIP

DVD

 

 

INSTANT REPLAY INSTANT SKIP

 

EASY

 

 

 

NAVI

 

 

 

VCR Plus+

REC MENU

EXTEND

 

 

CONTENT MENU

 

 

 

S

 

 

 

KIP

Distance : About 7 m (23 ft) from the front of the remote sensor

Angle : About 30° in each direction of the front of the remote sensor

*Do not expose the remote sensor of the recorder to a strong light source such as direct sunlight or other illumination. If you do so, you may not be able to operate the recorder via the remote control.

Notes

Direct the remote control at the remote sensor of the recorder.

Do not drop or give the remote control a shock.

Do not leave the remote control near an extremely hot or humid place.

Do not spill water or put anything wet on the remote control.

Do not disassemble the remote control.

18

Loading...
+ 42 hidden pages