Taylor TE150, TE400 User Manual

4 (1)
Taylor TE150, TE400 User Manual

General Operation (cont.)

OVERLOAD

The scale can be overloaded by a maximum of 5% above the scale's capacity, as follows:

Max Load

TE150 157.4 lb / 71.4 kg

TE400 420 lb / 190.4 kg

POWER OFF

To turn the scale off, press the “OFF” button.

Calibration Function

Occasionally the scale's accuracy should be verified by measuring a known weight of the scale's approximate capacity. Tare the scale by pressing ZERO, place the weight on the platform and note the reading. Calibrate the scale if necessary.

Calibration Procedure

You must use a CALIBRATED weight ONLY to properly recalibrate the scale.

For the TE150, use a 150 lb calibrated weight (or 60 kg if operating in kilos).

For the TE400, use a 400 lb calibrated weight (or 150 kg if operating in kilos).

1.While the scale is off, press and hold down the “TARE/HOLD” and “lb/kg” buttons. While holding down both these buttons, press the “ON” button to turn the scale on. When the display shows “8888” > “CAL”, the scale is in calibration mode.

2.Release the buttons. The display will show “CX” with a number (CX150 for the TE150; CX400 for the TE400). Next the display will show a number (the zero count) between 4700 and 6000. (Note: if operating the scale in kilograms, the scale will instead show “C60” for the TE150 or “C150” for the TE400. If the zero count is outside the range, please contact customer service.)

3.Press the “TARE/HOLD” button. The display will show “XXX0”.

4.Place a calibrated weight on the scale platform.

For the TE150, use a 150lb (or 60 kg) calibrated weight.

For the TE400, use a 400 lb (or 150 kg) calibrated weight.

The display will show a number between 1800 and 2300 (the span count). Note: the span count must be stable on the display before proceeding to step 5. If the span count is outside this range, please contact customer service

5.Press the “TARE/HOLD” button. The following will appear on the display:

For the TE150, the display will show “C150”> “End”> “150.0”

(or “C60”> “End”> “60.0” if operating in kilograms).

For the TE400, the display will show “C400”> “End”> “400.0”

(or “C120”> “End”> “120.0” if operating in kilograms).

6.The calibration is complete. Remove the weight from the scale.

Display Signals

LCD Shows

Low Battery ••••••••••••••••••• bAtt

Load is greater than

Maximum Overload ••••••••••••• oooo

Precautions

This scale is engineered to give you years of satisfactory service if you handle it carefully. Here are a few precautions:

1.Always read instructions thoroughly to ensure that you have the full benefit of all the unit's features.

2.DO NOT immerse unit in water, as doing so will cause damage to internal components and void the warranty. If you spill liquid on it, dry it immediately with a soft, lint-free cloth.

3.DO NOT clean the unit with an abrasive or corrosive material. This may scratch the plastic parts and corrode the electronic circuits.

4.DO NOT subject the units to excessive force, shock, dust, temperature or humidity. This may result in malfunction, shorter electronic life span, damaged battery and distorted parts.

5.DO NOT tamper with the unit's internal components. Doing so will invalidate the warranty on the units and may cause damage. The unit contains no user-serviceable parts.

7.Only use fresh batteries, as old batteries may leak and cause damage to the unit. Remove the batteries if the scale will not be used for a long period of time.

8.DO NOT dispose of batteries in fire. Disposing of this product in fire could cause batteries to explode or leak.

Specifications

Platform Size: 8-1/16” x 5”

Power: 120V adaptor (included) or six (6) “AA” batteries (not

included)

Dimensions: 12 1/4” x 12” x 2 1/8”

Weight: 9 3/4 lbs / 4.4 kgs

Operating Temperature Range: 40°F to 104°F

Accuracy: +/-1% + 1 division

Capacity: TE150 150 lbs x 0.2 lb

150 lbs x ¼ lb

68 kgs x 0.1 kg

TE400 400 lbs x 0.5 lb

400 lbs x ½ lb

181 kgs x 0.2 kg

Overload:TE150 157.4 lbs / 71.4 kgs

TE400 420 lbs / 190.4 kgs

Platform: TE150 Stainless steel

TE400 Tread painted steel

One Year Limited Warranty

This product is warranted against defects in materials or workmanship for one (1) year from date of original purchase. It does not cover damages or wear resulting from accident, misuse, abuse, or unauthorized adjustment and/or repair. Should this product require service (or replacement at our option) while under warranty, please pack the item carefully and return it prepaid, along with receipt showing date of purchase and a note explaining reason for return to:

Taylor Precision Products

2220 Entrada Del Sol, Suite A

Las Cruces, New Mexico 88001

Customer Service Phone: 1-800-225-4834

Customer Service Fax: 1-575-526-4347

www.taylorusa.com

There are no expressed warranties except as listed above. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

©2009 Taylor Precision Products and its affiliated companies, all rights reserved. Taylor® and Leading the Way in Accuracy® are registered trademarks of Taylor Precision Products and its affiliated companies. All rights reserved.

Made to our exact specifications in China.

NOT LEGAL FOR TRADE

TE150/TE400 11.09

TE150 / TE400

Digital

Receiving Scale

Leading the Way in Accuracy ®

Instruction Manual

Thank you for purchasing a Taylor® Digital Receiving Scale. Your scale is an example of superior design and craftsmanship. In order to optimize its function, be sure the read this instruction manual carefully before use. Keep instructions handy for future reference.

Loading...
+ 1 hidden pages