Tascam CD-X1700 User Manual

0 (0)
»
CD-X1700
DUAL CD PLAYER
OWNER’S MANUAL / MANUAL DEL USUARIO
D00785400A
English IMPORTANT SAFETY PRECAUTIONS
2 TASCAM CD-X1700 DUAL CD PLAYER
DO NOT cut off the mains plug from this
equipment.
DO NOT cut off the mains plug from this
equipment.
If the plug fitted is not suitable for the power points
in your home or the cable is too short to reach a
power point, then obtain an appropriate safety
approved extension lead or consult your dealer.
If nonetheless the mains plug is cut of
f, remove the
fuse and dispose of the plug
immediately, to avoid
a possible shock hazard by inadvertent connection
to the mains supply.
If this product is not provided with a mains plug, or
one has to be fitted, then follow the instructions
given below:
IMPORTANT: DO NOT make any connection to
the larger terminal which is marked with the letter
E or by the safety earth symbol c or coloured
GREEN or GREEN-and-YELLOW.
The wires in the mains lead on this product are
coloured in accordance with the following code:
BLUE : NEUTRAL
BROWN : LIVE
As these colours may not correspond with the
coloured markings identifying the terminals in
your plug proceed as follows:
The wire which is coloured BLUE must be
connected to the terminal which is marked with the
letter N or coloured BLACK.
The wire which is coloured BROWN must be
connected to the terminal which is marked with the
letter L or coloured RED.
When replacing the fuse only a correctly rated
approved type should be used and be sure to re-fit
the fuse cover.
IF IN DOUBT — CONSULT A COMPETENT
ELECTRICIAN.
TO THE USER
This equipment has been tested and found to
comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference when the equipment
is operated in a commercial environment. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instruction manual, may
cause harmful interference to radio
communications.
Operation of this equipment in a residental area is
likely to cause harmful interference in which case
the user will be required to correct the interference
at his own expense.
CAUTION
Changes or modifications to this equipment not
expressly approved by TEAC CORPORATION for
compliance could void the user's authority to
operate this equipment.
For the consumers in Europe
WARNING
This is a Class A product. In a domestic environment,
this product may cause radio interference in which
case the user may be required to take adequate
measures.
Pour les utilisateurs en Europe
AVERTISSEMENT
Il s’agit d’un appareil de Classe A. Dans un
environnement domestique, cet appareil peut
provoquer des interférences radio. Dans ce cas,
l’utilisateur peut être amené à prendre des mesures
appropriées.
Fur Kunden in Europa
Warnung
Dies is eine Einrichtung, welche die Funk-Entstörung
nach Klasse A besitzt. Diese Einrichtung kann im
Wohnbereich Funkstörungen versursachen ; in
diesem Fall kann vom Betrieber verlang werden,
angemessene Maßnahmen durchzführen und dafür
aufzukommen.
For U.S.A
IMPORTANT SAFETY INSTRUCTIONS (1) English
TASCAM CD-X1700 DUAL CD PLAYER 3
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8 Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9 Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10 Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
11 Only use attachments/accessories specified by the
manufacturer.
12 Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid
injury from tip-over.
13 Unplug this apparatus during lightning storms or
when unused for long periods of time.
14 Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
Do not expose this apparatus to drips or splashes.
Do not place any objects filled with liquids, such as
vases, on the apparatus.
Do not install this apparatus in a confined space such
as a book case or similar unit.
The apparatus draws nominal non-operating power
from the AC outlet with its POWER switch in the off
position.
4 TASCAM CD-X1700 DUAL CD PLAYER
SAFETY INFORMATION
This product has been designed and manufactured according to FDA regulations "title 21, CFR, chapter 1, subchapter J,
based on the Radiation Control for Health and Safety Act of 1968", and is classified as a class 1 laser product. There is no
hazardous invisible laser radiation during operation because invisible laser radiation emitted inside of this product is
completely confined in the protective housings.
The label required in this regulation is shown 1.
CAUTION
- DO NOT REMOVE THE PROTECTIVE HOUSING USING A SCREWDRIVER.
- USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY
RESULT IN HAZARDOUS RADIATION EXPOSURE.
- IF THIS PRODUCT DEVELOPS TROUBLE,CONTACT YOUR NEAREST QUALIFIED SERVICE PERSONNEL,AND DO NOT USE THE
PRODUCT IN ITS DAMAGED STATE.
Optical pickup: Type : KSS-213C
Manufacturer : SONY Corporation
Laser output : Less than 0.4 mW on the objective lens
Wavelength : 760 - 800nm
English IMPORTANT SAFETY INSTRUCTIONS (2)
Table of contents English
TASCAM CD-X1700 DUAL CD PLAYER 5
1. Before you start............................................... 6
1.1 Environmental conditions .......................... 6
1.2 Beware of condensation............................. 6
1.3 Handling of discs ....................................... 6
2. Functions and Controls ................................... 7
2-1. Main Unit (Front Panel) ........................... 7
2-2. Main Unit (Rear Panel) ............................ 7
2-3. Remote Controller (Top Panel)................. 8
2-4. Remote Controller (Bottom Panel)......... 10
2-5. Remote Controller (LCD)....................... 11
3. Playback operation........................................ 12
3-1. CUE ........................................................ 12
To memorize the CUE point ....................... 12
Stutter play with the CUE key .................... 12
3-2. CUE 1-3.................................................. 12
To memorize the CUE 1-3 points ............... 12
Stutter play with the CUE 1-3 keys ............ 12
3-3. Flash Start ............................................... 12
3-4. A-B Looping ........................................... 13
To store the LOOP points............................ 13
Disengage the loop play.............................. 13
Re-looping................................................... 13
Erasing the LOOP points............................. 13
Changing the LOOP end point (B point).... 13
3-5. Adjusting the tempo................................ 13
Tempo range................................................ 13
Using the TEMPO slider............................. 14
Auto BPM and TAP key.............................. 14
3-6. Pitch bending .......................................... 14
3-7. Key origina ............................................. 14
4. More advanced operation.............................. 15
4-1. Key control ............................................. 15
4-2. Scratching ............................................... 15
4-3. Brake....................................................... 15
Set the brake time........................................ 15
4-4. Effect....................................................... 15
Effect time setting ....................................... 16
Synchronizing the effect time
with the BPM .......................................... 16
Effect level setting....................................... 16
FLANGER................................................... 16
ECHO .......................................................... 16
FILTER........................................................ 16
4-5. Reverse play............................................ 17
4-6. Sampler ................................................... 17
Sampling...................................................... 17
Using the A-B loop as a sample source...... 17
Play the sampler .......................................... 17
Stop the sampler.......................................... 17
Erasing the recorded sample ....................... 17
Sampler loop................................................ 18
Sampler reverse ........................................... 18
Sampler pitch control .................................. 18
Sampler output level.................................... 18
Recall the sampling data ............................. 18
4-7. Track Memory / Recall........................... 18
Track memory ............................................. 18
Memory data................................................ 19
Recall........................................................... 19
4-8. Fader Start............................................... 20
4-9. Relay Play............................................... 20
4-10. Auto Cue ............................................... 20
4-11. Auto Ready ........................................... 20
4-12. Programmed Play.................................. 21
Create the program...................................... 21
Edit program................................................ 21
Insert program ............................................. 22
Delete program............................................ 22
4-13. MP3 file playback................................. 23
4-14. Preset menu........................................... 23
4-15. Backup memory.................................... 24
5. Specifications................................................ 25
Error messages ............................................ 25
Demensions ...........................................Back page
English 1. Before you start
6 TASCAM CD-X1700 DUAL CD PLAYER
1.1 Environmental conditions
The TASCAM CD-X1700 may be used in most
areas, but to maintain top performance, and
prolong operating life, observe the following
environmental conditions:
The nominal temperature should be between 5°C
and 35°C (41°F and 95°F).
Relative humidity should be 30 to 90 degrees non-
condensing.
Make sure that the drive unit is mounted in a level
position for correct operation.
The units should be mounted, using the supplied
rack mounting kits. A typical configuration is
shown below, but other configurations are
possible:
If the disc trays are more than 5 degrees
away from the horizontal, they will not
open or close.
Do not install this apparatus in a con-
fined space such as a book case or simi-
lar unit.
1.2 Beware of condensation
If the player (or a compact disc) is moved from a
cold to a warm place, or used after a sudden
temperature change, there is a danger of
condensation; vapor in the air could condense on
the internal mechanism, making correct operation
impossible. To prevent this, or if this occurs, leave
the player for one or two hours with the power
turned on, then turn the power off and on again.
NOTE
1.3 Handling of discs
The unit has been designed specifically for
reproduction of discs bearing the mark. No
other discs can be reproduced.
Observe the following:
Always place the compact discs in the trays with
their label facing upward (compact discs can
only be played on one side).
•To remove a disc from its storage case, press
down on the center of the case, and lift the disc
out, holding it carefully by the edges.
Finger marks and dust should be carefully wiped
off the disc's recorded surface with a soft cloth.
Unlike conventional records, the compact disc
has no grooves to collect dust and microscopic
debris, so gently wiping with a soft cloth should
remove most particles.
•Wipe in a straight motion from the inside to the
outside of the disc. Small dust particles and light
stains will have absolutely no effect on reproduc-
tion quality.
Never use such chemicals as record sprays, anti-
static sprays or fluid, benzine or thinner to clean
compact discs. Such chemicals will do irrepara-
ble damage to the disc's plastic surface.
Discs should be returned to their cases after use
to avoid serious scratches that could cause the
laser pickup to "skip".
Don't expose discs to direct sunlight or high
humidity and temperature for extended periods.
Long exposure to high temperature can warp the
disc.
Only use circular compact discs. Avoid using
non-circular promotional, etc. discs.
•To keep the laser pickups clean, don't touch
them. For the same reason, don't leave the disc
trays open unnecessarily.
2. Functions and Controls English
TASCAM CD-X1700 DUAL CD PLAYER 7
2-1. Main Unit (Front Panel)
1 POWER switch
Turns the power on and off. The tray LEDs light
when power is supplied.
When Timer start function is on, playback begins
when power is supplied.
2 Disc trays
Insert CD into these trays, label side upwards.
3 Tray LEDs
Lights when power is supplied.
4 OPEN keys
Open and close the appropriate tray.
These keys cannot be used when direct
mode (Preset menu: page 23) is off and
disc is being played back.
NOTE
2-2. Main Unit (Rear Panel)
5 OUTPUT jacks (RCA)
RCA connectors providing line level output
signals, one set each for discs 1 and 2.
6 DIGITAL OUTPUT (COAXIAL, S/PDIF)
Coaxial connectors provide digital output signals.
These connectors can output the 44.1KHz digital
signals constantly even if pitch control is activated
.
7 FADER START jacks (MINI jack)
The CD-X1700 can be controlled using the
external Fader start command through these jacks.
Connect the mixer which supports the fader start
function with appropriate cable as well as audio
signal ( page 20). (TIP: Start, GND: back cue)
8 ACCESSORY (MINI DIN 6P)
Connect the optional scratch controller TT-M1.
9 REMOTE (MINI DIN 8P)
Use this connector to connect the remote control
unit.
DO NOT use any cable with the CD-
X1700 except the cable supplied with
the unit.
Connect the cable in the way shown on
the illustration on the rear panel of the
CD-X1700. If you connect the cable in
any other way, you may damage the CD-
X1700.
WARNING
English 2. Functions and Controls
8 TASCAM CD-X1700 DUAL CD PLAYER
2-3. Remote Controller (Top Panel)
0 OPEN key
Opens and closes the appropriate tray.
These keys cannot be used when direct
mode (Preset menu: page 23) is off and
a disc is being played back.
q PLAY MODE / PGM key
Selects the play mode, either continuous play (all
play), single play (1 track play), or programmed
play.
Continuous play: No indication in the
LCD
Single play: SINGLE indicator in the
LCD will light
Programmed play: PROGRAM indicator in
the LCD will light
Pressing and holding the TIME/ENTER/SHIFT
key while pressing the PLAY MODE key, enters
program edit mode. ( page 21)
w TIME/ENTER / SHIFT key
Selects the time display mode, either elapsed,
remain or total remain.
ELAPSED: Elapsed time will show in the
numerical portion in display, but no
additional indicator will light.
NOTE
REMAIN: REMAIN indicator in the LCD will
light
TOTAL REMAIN: The track number display area
shows the number of tracks of
inserted disc, however, for 5 seconds
in the end of track, the current track
number flashes and for 5 seconds in
the beginning of the track, the
current track number lights.
Another function of this key is the modifier key
(SHIFT function). Holding SHIFT while pressing
another key performs the following functions;
SHIFT + PLAY MODE: Program Edit
SHIFT + FLASH: Track memory Recall
SHIFT + SET: Track memory
SHIFT + TEMPO: Memory bank select
SHIFT + BEND -: Auto Cue on/off
SHIFT + BEND +: Auto Ready on/off
SHIFT + TAP: Parameter display select
SHIFT + Jog Wheel: Preset
SHIFT + B: Loop end point edit
SHIFT + CUE: Select the CUE key’s
operation
e LCD
Displays visual feedback for CD-X1700 functions
r TAP / DISPLAY key
Sets the tempo in BPM by tapping this key. When
you press this key, the parameter counter mode
momentarily changes to TAP BPM display mode.
( page 14)
2. Functions and Controls English
TASCAM CD-X1700 DUAL CD PLAYER 9
Pressing and holding the SHIFT key while
pressing this key selects the parameter display
mode.
TEMPO KEY TA P BPM ( DIR).
t SCRATCH key
Turns the scratch play mode on and off. When
scratch play mode is on, this key lights and scratch
can be performed by Jog wheel. ( page 15)
y BRAKE key
Turns the brake function on and off and sets the
brake time using the Jog wheel. ( page 15)
Turns the relay play on and off. ( page 20)
u REVERSE key
Changes the playback direction between forward
and backward. ( page 17)
i SEARCH key
Turns on or off the Search function on the Jog
wheel. When this key is lit, the Jog wheel acts as
a search dial.
After 5 seconds without search operation, the unit
will exit the search mode automatically.
o Track Skip keys
Use these to perform track searches.
p CUE key
Locates to the cue point, then pauses.
Stutter play can be performed with this key.
( page 12)
Selects the CUE key’s operation mode. ( page
12)
a PLAY/PAUSE key
Changes the playback mode between playback and
pause.
The light stays on solid in playback mode and
flashes in pause mode
s Jog Wheel
The following functions can be controlled by the
Jog wheel.
Search
Pitch Bend
Scratch
Brake time
Key control
Preset menu
•Effect parameters
Sampler tempo/level
Program edit
•Track memory number select
d FX SYNC key
Turns on and off synchronization of the effect time
with the MPB. ( page 16)
f FLANGE key
Turns the Franger effect on and off. ( page 16)
g ECHO key
Turns the Echo effect on and off. ( page 16)
h FILTER key
Turns the Filter effect on and off. ( page 16)
j FLASH / RECALL / DEL key
Turns the flash start mode on and off. ( page 12)
Recalls the track memory data. ( page 19)
Deletes the current selected song from the program
list. ( page 22)
k SET / MEMO / INS key
Set the cue points with CUE 1-3. ( page 12)
Memorizes the track memory data ( page 18)
Adds the current selected song into the program
list. ( page 22)
l CUE 1-3 keys
Depending on the setting, these keys locate to cue
points, flash start from cue points (default), or
stutter play from cue points. ( page 12)
; LOOP, A, and B keys
Sets or erases the loop points, or engages or
disengages the loop playing. ( page 13)
z SAMPLE keys
This key lights when sample playback takes place
and flashes when sample recording takes place.
Press and hold this key and press the IN key to
enter reverse sample playback mode, and press and
hold this key and press the OUT key to enter loop
sample playback mode. ( page 17)
English 2. Functions and Controls
10 TASCAM CD-X1700 DUAL CD PLAYER
, Remote Connector
Connect this to the REMOTE connector on the rear
panel of the main unit.
DO NOT use any cable except the cable
supplied with the CD-X1700.
WARNING
Connect the cable to the CD-X1700 as
shown on the illustration on the rear
panel. If you connect the cable in any
other way, you may damage the CD-
X1700.
2-4. Remote Controller (Bottom Panel)
x IN and OUT keys
Use these keys to record and clear the sampled
sound. When you have recorded the sample, these
keys will light. Start and stop sample playback
using these keys. ( page 17)
Pressing and holding the IN key then using the Jog
wheel controls the sampler output level.
c LOOP and REV LEDs
Indicates the sampler playback mode. ( pages 17
- 18)
v KEY ORIG / KEY key
Turns the KEY ORIGINAL function on and off.
( page 14)
Sets the key control value. ( page 15)
b TEMPO / BANK key
Selects the tempo range, either +/-8, 16, 32, 100 or
0%.
Selects the track memory bank from A to E.
( page 18)
n BEND +/ A.RDY, –/A.CUE keys
Use these keys to perform pitch bending.
( page 14)
Turns the AUTO CUE function on and off.
( page 20)
Turns the AUTO READY function on and off.
( page 20)
m TEMPO slider
Changes the playback tempo. ( page 14)
2. Functions and Controls English
TASCAM CD-X1700 DUAL CD PLAYER 11
2-5. Remote Controller (LCD)
. M indicator
If there is track memory data for the current
selected track in the current selected memory bank,
this indicator lights.
/ TRACK indicator
! REMAIN indicator
When the time mode is set to remain time mode,
this indicator lights.
@ SINGLE indicator
When the play mode is set to single play, this
indicator lights.
# PGM indicator
When the play mode is set to programmed play,
this indicator lights.
$ MP3 indicator
When a MP3 CD-ROM disc is inserted, this
indicator lights.
% Time display
This section is used to show track number, time
values or messages.
^ FLASH indicator
When flash start is activated, this indicator lights.
Flash start mode is on by default, or the last setting
of flash start will be retained. If you set it to OFF
then turn the power off, when power is turned back
on, flash start will be OFF.
& Memory bank indicators
Lights the current selected memory bank indicator.
* A.CUE indicator
Lights when AUTO CUE function is turned on.
( A.RDY indicator
Lights when AUTO READY function is activated.
) RELAY indicator
Lights when relay play is set to on.
Q LOOP indicator
Lights when loop play is engaged.
W S indicator
Lights when loop mode is set to single loop.
E ALL indicator
Lights when loop mode is set to all loop.
R Time Address Bar
Shows the current play position relative to the
current track.
T PAR indicator
Lights when parameter display shows the effect
parameter.
Y TEMPO indicator
Lights when parameter display shows the TEMPO
value.
U KEY indicator
Lights when parameter display shows the key
value.
Lights when key value is set to other than 0%.
I Parameter display
Displays the various parameters.
O TAP indicator
Lights when parameter display shows the tap
value.
P BPM indicator
Lights when parameter display shows the auto
BPM value.
A DIR indicator
When a MP3 CD-ROM disc is inserted, this
indicator lights and parameter display shows the
current selected directory number.
S KEY ORIGINAL indicator
Lights when key original function is activated.
English 3. Playback operation
12 TASCAM CD-X1700 DUAL CD PLAYER
3-1. CUE
The CD-X1700 can memorize the play start point
as a cue point. If the cue point is memorized,
pressing the CUE key locates the unit to the cue
poin.
To memorize the CUE point
There are two ways to store the cue point.
Pressing and holding the SHIFT key then pressing
CUE selects the method for the CUE key’s
operation.
: Last play start point is stored as the CUE
point.
: Pressing the CUE key when unit is paused
stores the current point as the cue point.
Stutter play with the CUE key
When unit is paused at the cue point, the unit will
play when this key is pressed, and enter pause
mode when CUE is released.
If the PLAY key is pressed during CUE playback,
the unit will go into normal play mode.
3-2. CUE 1-3
The CD-X1700 can have another three cue points
stored with the CUE 1-3 keys.
To memorize the CUE 1-3 points
1. Find the desired point.
2. Press the SET key. The parameter display shows
.
3. Press the desired CUE key.
When the CUE key has the stored point, the CUE
key lights. The stored cue point cannot be erased
but can be overwritten.
When the unit is paused and the
indicator in the LCD lights, pressing the
SET key then pressing the CUE 1-3 key
starts the unit automatically.
When the unit is paused and the
indicator in the LCD doesn’t light, press-
ing the SET key then pressing the CUE 1-
3 key flashes the pressed CUE 1-3 key
three times then lights.
For three seconds after storing the cue
point, you cannot store another cue
point.
Stutter play with the CUE 1-3 keys
When the unit is paused at the cue 1-3 point, the
unit will play when the appropriate CUE 1-3 key is
pressed, and enter pause mode when CUE 1-3 is
released.
If the PLAY key is pressed during CUE playback,
the unit will go into normal play mode.
3-3. Flash Start
The CD-X1700 has a flash start function that can
be used with the CUE 1-3 keys.
When the flash start function is activated (when the
indicator in the LCD lights), pressing the
CUE 1-3 key enables flash start.
When the indicator in the LCD
doesn’t light, the unit is back in cue
mode. In this mode, pressing the CUE 1-
3 key locates the stored cue point then
the unit pauses.
NOTE
NOTE
3. Playback operation English
TASCAM CD-X1700 DUAL CD PLAYER 13
3-4. A-B Looping
To store the LOOP points
Loop points can be stored when loop
points are not stored on the unit (A and
B key don’t light). If loop points are
already stored, erase these points first,
then store the loop points again.
Both loop start (A) and end (B) points
can set to within a track.
A-B looping can be performed when the
loop mode is set to “A-B” (preset 01).
When loop mode is set to “A-B”, the "S"
and “ALL” indicators in the LCD don’t
light.
1. Press the A key when playing or pausing. The A
key will light and the B key will start flashing.
2. Press the B key when playing or pausing.
LOOP, A, and B keys will light. If the loop B
point is set when the unit is playing, the CDX-
1700 starts loop playback seamlessly. If the
loop B point is set when the unit is paused, the
CDX-1700 goes to the loop start point then
pauses. At this time the indicator in the
LCD lights.
Disengage loop play
When loop play is engaged, pressing the LOOP
key disengages loop play. In this case, the unit
continues playback and LOOP light goes off, but
the loop points are not erased.
When loop play is engaged, locating to the out
point of a loop section disengages loop play (i.e.
pressing the CUE key, etc…). The LOOP key goes
off, but the loop points are not erased.
NOTE
Re-looping
When loop play is disengaged and loop points are
already stored, pressing the LOOP key starts re-
loop playback and the LOOP key lights.
Erasing the LOOP points
Pressing the A and B key at the same time erases
the loop points. At this time, the A and B keys go
off.
If the tray is opened, your loop points are erased.
Changing the LOOP end point (B point)
Pressing the B key when the loop is playing
changes the loop end point.
Pressing and holding the SHIFT key then pressing
the B key edits the B point using the Jog wheel.
Pressing the B key overwrites the new B point and
exits the edit mode.
The Loop B point can be moved before
the current B point only.
3-5. Adjusting the tempo
Tempo range
The CD-X1700 features +/-8, 16, 32, 100, and 0%
of tempo control range. Pressing the TEMPO key
changes the tempo control range. The Parameter
display shows the selected tempo/key range
momentary. If 0% is selected, the parameter
display shows .
NOTE
English 3. Playback operation
14 TASCAM CD-X1700 DUAL CD PLAYER
Using the TEMPO slider
The TEMPO slider controls playback tempo.
Tempo changes are displayed in the LCD.
Auto BPM and TAP key
The CD-X1700 features automatic BPM count
function and TAP mode BPM count function.
When parameter display mode is set to BPM, the
BPM is counted automatically and displayed in the
parameter display. The TAP LED blinks in tempo.
Pressing the TAP key repeatedly counts the song
tempo in BPM manually. Tapped BPM is shown in
the LCD parameter display and the TAP LED
blinks in tempo. This BPM affects the TEMPO
slider moving. If the TEMPO slider is moved, the
BPM will be changed automatically.
Pressing and holding the TAP key for more than
1.5 seconds erases the tapped BPM value.
Pressing and holding the TAP key then moving the
Jog wheel (within 1.5 seconds) adjusts the BPM
manually.
BPM is also used for the effect time or
beat parameter (P15). When you set the
BPM using with the TAP key, tapped
BPM will be used for the effect time or
beat parameter. When there is no
tapped BPM (or you erase the tapped
BPM), auto counted BPM will used for
effect parameter instead
NOTE
3-6. Pitch Bending
When playing back a disc, pressing the BEND + or
– key, or using the Jog wheel can change playback
tempo momentary. Pressing the + key or moving
the Jog wheel clockwise increases the playback
speed and returns to original speed when release
this key or stop the Jog wheel moving. Pressing
the - key or moving the Jog wheel
counterclockwise decreases the playback speed
and returns to original speed when release this key
or stop the Jog wheel moving.
When SEARCH key, SCRATCH key, or a
effect key is not lit, the Jog wheel works
for pitch bend function.
The maximum pitch bend range is 16%.
When Key Original function is activated,
playback key is fixed.
3-7. Key Original
When tempo range is set to +/-8, 16, or 32%,
pressing the KEY ORIG key turns the key original
function on and off. When key original function is
turned on, tempo control does not affect the
playback key. When the key original function is
turned on, indicator in the LCD lights.
If tempo range is set to +/-32% or 100%, the key
original function does not work.
When the key original function is turned on,
parameter display shows in the KEY mode.
NOTE
4. More advanced operation English
TASCAM CD-X1700 DUAL CD PLAYER 15
4-1. Key control
The CD-X1700 features up to +/-16% key control.
Key control range is determined with tempo range
setting.
When tempo and key control range is set to 8%,
key value can be set in 0.1% steps. When tempo
and key control range is set to 16%, key value can
be set in 0.2% steps. When tempo control range is
set to 0%, 32%, or 100%, the key control function
does not work.
Pressing and holding the KEY key then moving the
Jog wheel sets the key control value.
Note that the key value shows a total of the value
together with any changes made by using the
slider.
When the key original function is acti-
vated, the key control function does not
work.
4-2. Scratching
When the SCRATCH key is activated, scratching
can be performed with the Jog wheel.
For 3 seconds after the flash start or
cuing with CUE 1-3 key, or cuing with
CUE key, backward direction of
scratching cannot be performed
Backward direction of the scratching can
be performed up to 7 seconds.
When SEARCH function is on, the Jog
wheel works as the search dial.
When filter effect is activated with
manual mode, scratch function cannot be
performed with the Jog wheel (page 16).
NOTE
NOTE
4-3. Brake
Brake function simulates the braking audio just
like turning off the analog turntable. Pressing the
BRAKE key turns the brake function on and off.
When brake function is activated, BRAKE key
lights.
Set the brake time
Pressing and holding the BRAKE key then using
the Jog wheel adjusts the brake time. Brake time
can be set to 0.1 to 5 seconds in 0.1 sec. steps.
Pressing the PLAY/PAUSE key while unit is
playing performs the braking.
Pressing the PLAY/PAUSE key during the braking
starts the music again with current tempo.
4-4. Effects
The CD-X1700 includes three effects, Flanger,
Echo, and Filter. One effect can be activated at the
same time.
Pressing one of the effect keys can activate the
effect.
Pressing the FX SYNC key synchronize the effect
time with the BPM.
Pressing and holding the SHIFT key then pressing
one of effect key can adjust the effect level with the
Jog wheel.
Loading...
+ 33 hidden pages