Targus AMB09US User Manual

Size:
2.45 Mb
Download

User Guide

Targus Bluetooth Comfort Laser Mouse

Introduction

Thank you for your purchase of the Targus Bluetooth Comfort Laser Mouse.This mouse uses Bluetooth technology which provides a seamless connection up to 33 feet (10 m) away. This is a plug and play device so no additional software is required. The advance scroll wheel feature program can be downloaded from the Targus website.

Contents

Targus Bluetooth Comfort Laser Mouse

2 x AA Batteries

User Guide

System Requirements

Hardware

Bluetooth-enabledcomputer

Operating System

Microsoft Windows® 2000

Microsoft Windows® XP

Microsoft Windows Vista®

Microsoft Windows® 7

Mac OS® X 10.4 or later

2

Targus Bluetooth Comfort Laser Mouse

Installing the Batteries

1.Remove the battery cover from the top of the mouse by using the notch on the back. Carefully lift the cover up as shown in the diagram.

2.Remove the battery safety clip by squeezing the center of the clip and sliding it back, towards the rear of the mouse. Lift up and rotate the clip out of the way.

NOTE: THE BATTERY SAFETY CLIP WILL NEED TO BE IN THE SECURE, LOCKED POSITION BEFORE THE BATTERY COVER CAN BE PUT BACK IN PLACE.

3

Targus Bluetooth Comfort Laser Mouse

3. Slide and lift to remove the battery holder as shown.

4.Insert the two AA batteries, making sure that the positive (+) and negative (-)ends of each battery match the polarity indicators inside the battery compartment.

4

Targus Bluetooth Comfort Laser Mouse

5. Replace the battery safety clip and by sliding it forward until it clicks into place and then replace the battery cover.

6.Turn on the mouse by pressing the power On/Off button on the bottom of the mouse. Hold for 3 seconds and then release.

Power button

5

Targus Bluetooth Comfort Laser Mouse

Power On:

Press and hold the power button for 3 seconds and then release.

The battery life indicator will briefly light up showing the current power level of the batteries.

Power Off:

Press and hold the power button for 3 seconds and then release. The battery life indicator will briefly light up and then fade out.

Battery Check:

After the mouse is turned on, quickly press and release the power button. The battery life indicator will light up showing the current power level of the batteries.

Initial Mouse Setup

Enable Discovery mode:

The mouse will go into pairing mode automatically after it is powered on. The 1st and 3rd LEDs will flash alternately for 60 seconds; this indicates that the pairing sequence is in operation. Once the connection is established, the 1st and 3rd LED lights will light up steadily for 3 seconds.

1st LED

3rd LED

If the connection is not established by the end of 60 seconds, the mouse will go into sleep mode. Click on any mouse button to exit from sleep mode. The pairing sequence will re-startautomatically.

6

Targus Bluetooth Comfort Laser Mouse

Power Saving mode:

After an extended period of time, if the mouse is not used, it will automatically enter power saving mode to conserve power and increase battery life. Click on any mouse button to resume the normal operation. The mouse may take a few seconds to reconnect with your computer.

Battery Life Indicator

3

LEDs lit

Full power

 

 

 

2

LEDs lit

Half power

 

 

 

1

LED lit

Low power

 

 

 

NOTE: WHEN THE FIRST LIGHT IS BLINKING, PLEASE REPLACE THE BATTERIES

Power Management

To extend the life of your battery, turn off the mouse while travelling or when you’re not using it.

7

Targus Bluetooth Comfort Laser Mouse

Initial Configuration

Before you can begin using your Bluetooth® mouse, you will first need to perform some initial setup steps.

NOTE: PLEASE USE THE LATEST BLUETOOTH DEVICE DRIVER. INSTRUCTION SCREENS MIGHT VARY DEPENDING ON THE VERSION OF YOUR BLUETOOTH DEVICE DRIVER.

8

Targus Bluetooth Comfort Laser Mouse

Connecting with Bluetooth Software:

WIDCOMM or Microsoft (Windows XP & Windows Vista)

1.Go to the Bluetooth Places icon located on your desktop or in the system tray and double click, then click Add a Bluetooth Device.

(Windows XP)

(Windows Vista)

2. The Bluetooth Wizard screen will prompt. Please follow the onscreen instructions.

(Windows XP)

(Windows Vista)

9

Targus Bluetooth Comfort Laser Mouse

3.Power on the mouse and it will automactically go into discovery mode. Click Next to continue pairing and the computer will search for the mouse.

(Windows XP)

(Windows Vista)

4. The confirmation window will appear after the computer finishes detecting the Bluetooth devices. Select the Bluetooth Wireless Mouse and click Next to continue. (There may be one or more different Bluetooth devices detected.) If the mouse is not detected, please make sure the power is on and in discovery mode. PressSearch Again tore-pairthe device.

(Windows XP)

(Windows Vista)

10