Symphonic ZEKTOR MAS3 User Manual
Size:
430.71 Kb
Download

ZEKTORTM MAS3

Multi-channelAudio Switch

Owner’s Manual

www.zektor.com

Rev: 2

03/12/04

Important Safety Instructions!

Read all instructions for prior to installation of your product. Retain this User's Manual for future reference.

Adhere to all safety and operation instructions.

Before cleaning this product, unplug from the wall outlet. Do not use liquid cleaning products. Use a damp cloth for cleaning.

Do not use this product on an unstable cart, stand, or table. The product may fall, causing serious injury to a child, and serious damage to the product. Ensure that any attached cables cannot be tripped over.

This product is supplied with a UL Class 2 power supply as indicated on the product packaging. Use this product only with the supplied power supply. If you are unsure about the type of AC power in your home, consult your product dealer or a local power company.

Power cords should be routed so they will not be stepped on or rolled over.

If your product is not operating properly, do not attempt to service this product yourself. Refer to a qualified service personnel.

2

A MAS3 Overview

Operating the MAS3 is straight forward and simply a matter of plugging the MAS3’s power supply into an available A.C. outlet, and then plugging the MAS3’s power supply into the back of the MAS3.

To operate the MAS3 manually, press the power switch, located on the very left of the MAS3 to cycle power.

Press any one of the three channel switches to switch the MAS3 to the selected channel.

If the MAS3’s power is turned off, selecting any one of the three inputs will cause the MAS3 to power on and switch to the selected channel.

POWERTOGGLE

CHANNEL1

CHANNEL2

CHANNEL3

POWER TOGGLE. Pressing this button will cycle power from on to off, and off to on.

CHANNEL 1. Pressing this button will select channel 1 of the MAS3’s inputs, if power is off when this button is pressed, then the MAS3 will power on, and select channel 1.

CHANNEL 2. Pressing this button will select channel 2 of the MAS3’s inputs, if power is off when this button is pressed, then the MAS3 will power on, and select channel 2.

CHANNEL 3. Pressing this button will select channel 3 of the MAS3’s inputs, if power is off when this button is pressed, then the MAS3 will power on, and select channel 3.

3

Using the MAS3 with a Remote Control

Remote operations of the MAS3 are accomplished through the use of just about any remote control. A remote control is not supplied with the MAS3, yet the versatile programming modes of the MAS3 allows the MAS3 to work with virtually any remote control. The next section"Programming your Remote Control" on page 5, describes how to setup your remote controller. After your remote control is programmed the following describes thepre-programmedfunctions of the MAS3.

There are 9 separate remote controlled commands understood by the MAS3. They are:

POWER

CBL /

TV VCR SAT DVD RCVR

1

2

3

4

5

6

7

8

9

PIP

0

ENT

VOL CH

POWERTOGGLE.The MAS3 can be toggled from standby to power on, and back to standby using a single button of the remote.

SELECTIN1. Select input 1. If the MAS3 is in standby mode, it will power on and then select input 1.

SELECTIN2. Select input 2. If the MAS3 is in standby mode, it will power on and then select input 2.

SELECTIN3. Select input 3. If the MAS3 is in standby mode, it will power on and then select input 3.

POWEROFF. The MAS3 can be set to standby mode by pressing a single button of the remote. Once the MAS3 is in standby mode,

further presses of the POWEROFF button will be ignored. This command is useful when using the “macro” feature of some programmable remote controls, and is used when it is unknown whether the MAS3 is already in standby mode or not.

POWERON. The MAS3 can be powered on from standby by pressing a single button of the remote. Once the MAS3 is power on, further presses of thePOWERON button will be ignored. This command is useful when using remote controls that allow “macro” programming, where it is unknown whether the MAS3 is already power on or not.

SETDIMMODE. Toggles through three different bright/dim display modes. They are: Bright all the time. Dim all the time. Bright for 4 seconds after any keypress, and then automatically dim.

+

+

_

_

SELECT+. Select the next higher input. If input 3 is currently selected, then this command will cause input 1 to be selected.

SELECT-.Select the next lower input. If input 1 is currently selected, then this command will cause input 3 to be selected.

4