3-756-869-31(1)
FM/AM Clock Radio
Operating Instructions
Instrukcja obs ugi
N·vod k obsluze (obraªte stranu)
Haszn·lati ˙tmutatÛ (a h·toldalon)
ICF-C760
|
Sony Corporation © 1998 |
Printed in Malaysia |
|
|
|
|
|
|
L H |
BRIGHT |
CLOCK RADIO BUZZER |
A ALARM B |
RADIO BUZZER |
– TIME SET + |
|
ALARM RESET/OFF |
|
|
|
|
|
|
OFF RADIO ON/SLEEP |
SNOOZE/DATE/SLEEP OFF |
||
|
|
|
|
AM FM BAND |
|
Bottom |
|
|
|
|
|
SpÛd |
|
|
|
VOL |
|
|
|
|
|
|
|
|
|
|
|
|
TUNE |
English
WARNING
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.
Before You Begin
Thank you for choosing the Sony clock radio! The clock radio will give you many hours of reliable service and listening pleasure.
Before operating the clock radio, please read these instructions thoroughly and retain them for future reference.
Features
•Dual alarm
•Date display
•Display with adjustable brightness
•Adjustable legs to change the angle of the unit
•Forward/reverse time setting
•Power backup to keep the clock operating during a power interruption with a 6F22 battery (not supplied) installed
Installing the
Battery
To keep good time, your clock radio needs one 6F22 battery (not supplied), in addition to house current. The battery keeps the clock operating in the event of a power interruption. Before setting the time on your clock radio, open the lid at the bottom of the unit, install the battery with correct polarity and then close the lid.
•After a power interruption, the displayed time may not be always correct. (It may gain or lose about 10 minutes per hour.)
Knowing When to Replace the Battery
To check battery power, unplug the power cord from the wall outlet and plug it in again after a few minutes. If the displayed time is incorrect, replace the battery with a new one.
Setting the Clock
and the Date
Setting the Clock
1Plug in the unit.
The display will flash “0:00”.
2While holding down CLOCK, press either + or – above TIME SET till the correct time appears in the display.
When you release CLOCK, the clock begins to operate.
•To set the current time rapidly, keep pressing CLOCK and the + or – button together to advance or return to a time that is within a few minutes of the current time. Then press the + or
– button to set the time to the current time.
Setting the Date
1While holding down SNOOZE/DATE/ SLEEP OFF, press either + or – above TIME SET till the correct date appears in the display. Then, release SNOOZE/ DATE/SLEEP OFF.
•To display the date, press SNOOZE/DATE/ SLEEP OFF. The display returns to the current time when you release SNOOZE/DATE/SLEEP OFF.
Changing the Brightness of the
Display Window
To change the brightness of the display window, slide BRIGHT (brightness) to H (high) or L (low).
Changing the Angle of the Clock
Radio
You can change the angle of the unit by pulling the legs in the direction of the arrow as illustrated.
Operating the Radio
1Press RADIO ON/SLEEP to turn on the radio and adjust VOL (volume).
2Select FM or AM, and tune in to a station using the TUNE (tuning) dial.
•To turn off the radio, press RADIO OFF/ ALARM RESET/OFF.
•To improve radio reception
FM: Since the antenna is encased in the AC power cord, extend the cord to improve FM reception.
AM: Rotate the unit horizontally for optimum reception. A ferrite bar is built into the unit.
Setting the Alarm
To set the radio alarm, first tune in to a station and adjust the volume.
1While holding down the ALARM A or B button (for example, A for the radio or B for the buzzer), press either + or – above TIME SET till the desired time appears in the display. When you release ALARM A or B, ALARM A or
B indicator and ”:” stop flashing and light up, and the current time appears in the display.
2Set the ALARM A selector (for radio) to RADIO or ALARM B selector (for buzzer) to BUZZER.
The alarm will come on at the preset time and automatically turn itself off after 59 minutes.
•If you set ALARM A and ALARM B at the same desired time, only ALARM A will work.
•To shut off the alarm, press RADIO OFF/ ALARM RESET/OFF. The alarm will come on at the preset time the next day.
•To cancel either alarm, while holding down the
ALARM A or ALARM B button, press RADIO OFF/ALARM RESET/OFF.
•To doze for a few more minutes, press
SNOOZE/DATE/SLEEP OFF.
The alarm will shut off, but will come on again after about 6 minutes. You can repeat this process as many times as you like.
•To adjust the radio alarm volume, turn VOL.
•To check the preset time, press ALARM A or B.
Setting the Sleep
Timer
Enjoy falling asleep to the radio using the built-in sleep timer that shuts off the radio automatically at a preset time.
1Press RADIO ON/SLEEP.
The radio turns on. It will go off after the preset time has passed. You can set the sleep timer to 90, 60, 45, 30 or 15 minutes.
Every push changes the display as follows.
Current time On 90 60 15 30 45
The radio will play for the time you set, then shut off.
•To turn off the radio before the preset time, press SNOOZE/DATE/SLEEP OFF.
Precautions
•Operate the unit on the power sources specified in “Specifications”.
•The nameplate indicating operating voltage, etc. is located at the bottom of the AC power adaptor.
•To disconnect the power cord (mains lead), pull it out by the plug, not the cord.
•The unit is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet even if the unit itself is turned off.
•Do not place the unit on the surfaces (rugs, blankets, etc.) or near materials (curtains, draperies) that block the ventilation holes.
•Should anything fall into the unit, unplug the unit and have it checked by qualified personnel before operating it further.
•To clean the casing, use a soft cloth dampened with a mild detergent solution.
•Please note that accordingly only Sound and TV-Radio Receivers meant for the entire population are allowed to be received via this set. It is prohibited to receive all other transmission such as police radio or mobile radio.
Battery Warning
When the unit is to be left unplugged for a long time, remove the battery to avoid undue battery discharge and damage to the unit from battery leakage.
If you have any questions or problems concerning your unit, please consult your nearest Sony dealer.
Specifications
Time display
24-hour system
Frequency range
FM: 87.6 - 107.5 MHz
AM: 531 - 1,602 kHz
Speaker
Approx. 5.7 cm (2 1/4 in) dia.
Power output
120 mW (at 10% harmonic distortion)
Power requirements
220 - 230 V AC, 50 Hz
For power backup: 9V DC, one 6F22 battery
Battery life
Approx. 36 hours using the Sony S-006P(U) battery
Dimensions
Approx. 271 × 63 × 68 mm (w/h/d)
(10 3/4 × 2 1/2 × 2 3/4 in) not incl. projecting parts and controls
Mass
Approx. 550 g (1lb 3 oz) not incl. battery
Design and specifications are subject to change without notice.
Polski
OSTRZEØENIE
Aby zapobiec niebezpieczeÒstwu poøaru lub poraøenia pr±dem elektrycznym, nie naraøaj niniejszego urz±dzenia na dzia anie deszczu lub wilgoci.
Aby unikn±Ê poraøenia pr±dem elektrycznym, nie otwieraj obudowy. Naprawy powierzaj tylko wykwalifikowanemu personelowi serwisu.
Przygotowanie
DziÍkujemy Ci za zakup radia z zegarem firmy Sony! Radio z zegarem zapewni Ci wiele godzin niezawodnego dzia ania i przyjemno ci ze s uchania muzyki.
Zanim rozpoczniesz eksploatacjÍ radia z zegarem, prosimy, aby dok adnie przeczyta instrukcjÍ obs ugi i zachowa j± w celu uzyskania dalszych referencji.
Charakterystyka
•PodwÛjny alarm
•Wy wietlenie daty
•Wy wietlacz z regulowanym o wietleniem
•Wysuwane nÛøki, pozwalaj±ce na regulacjÍ k±ta ustawienia urz±dzenia
•Nastawianie czasu do przodu i do ty u
•Wspieranie pamiÍci bateri± 6F22 (wyposaøenie dodatkowe), zapewniaj±ce dzia anie zegara w przypadku przerwy w dostawie energii
Instalacja baterii
Aby zapewniÊ prawid owe trzymanie czasu musisz w swoim radiu z zegarem dodatkowo do zasilania z sieci zainstalowaÊ jedn± baterie 6F22 (wyposaøenie dodatkowe). Bateria podtrzymuje dzia anie zegara w wypadku przerwy w dostawie energii elektrycznej. Zanim nastawisz czas na radiu z zegarem, otwÛrz pokrywÍ na spodzie urz±dzenia, zainstaluj bateriÍ uwaøaj±c na prawid owe umieszczenie biegunÛw i zamknij pokrywÍ.
•Po przerwie w dostawie energii elektrycznej wy wietlony czas moøe nie byÊ prawid owy. (Zegar moøe siÍ pieszyÊ lub pÛºniÊ 10 minut na godzinÍ.)
Kiedy wymieniaÊ bateriÍ
Aby sprawdziÊ moc baterii, od ±cz przewÛd zasilania pr±dem zmiennym od gniazdaciennego i po kilku minutach pod ±cz ponownie.
Je li wy wietlony czas jest nieprawid owy, wymieÒ bateriÍ na now±.
Nastawianie zegara i daty
Nastawianie zegara
1Pod ±cz zestaw do sieci.
Na wy wietlaczu bÍdzie pulsowaÊ wskazanie Ü0:00á.
2Trzymaj±c wci niÍty CLOCK, naciskaj + lub â ponad TIME SET, dopÛki na wy wietlaczu nie pojawi siÍ prawid owe wskazanie czasu.
Gdy zwolnisz CLOCK zegar zacznie chodziÊ.
•Aby szybko nastawiÊ aktualny czas, przytrzymaj wci niÍty jednocze nie przycisk CLOCK oraz + lub â, aby szybko nastawiÊ przybliøony czas zmniejszaj±c lub zwiÍkszaj±c wy wietlenie, nastÍpnie naciskaj + lub â, aby dok adnie nastawiÊ czas.
Nastawianie daty
1Trzymaj±c wci niÍty SNOOZE/DATE/ SLEEP OFF naciskaj + lub â ponad TIME SET, dopÛki na wy wietlaczu nie pojawi siÍ prawid owa data. NastÍpnie zwolnij SNOOZE/DATE/SLEEP OFF.
•Aby wy wietliÊ datÍ naci nij SNOOZE/DATE/ SLEEP OFF. Wy wietlacz powraca do normalnego wskazania gdy zwolnisz
SNOOZE/DATE/SLEEP OFF.
Zmiana jasno ci o wietlenia okienka wy wietlacza
Aby zmieniÊ jasno Ê okienka wy wietlacza przesuwaj BRIGHT (jasno Ê) w kierunku H (wysoka) lub L (niska).
Zmiana k±ta ustawienia radia z zegarem
Moøesz zmieniÊ k±t ustawienia zestawu wyci±gaj±c nÛøki w kierunku strza ki jak pokazano na rysunku.
Obs uga radia
1Naci nij RADIO ON/SLEEP, aby w ±czyÊ radio w wyreguluj VOL (g o no Ê).
2Nastaw FM lub AM i regulatorem TUNE (strojenia) nastrÛj ø±dan± stacjÍ.
•Aby wy ±czyÊ radio, naci nij RADIO OFF/ ALARM RESET/OFF.
•Aby poprawiÊ odbiÛr
FM: Poniewaø antena znajduje siÍ w przewodzie zasilania, rozci±gnij go, aby poprawiÊ odbiÛr pasma FM.
AM: Aby uzyskaÊ jak najlepszy odbiÛr, obracaj zestaw poziomo. W zestawie wbudowana jest antena o rdzeniu ferrytowym.
Nastawianie alarmu
Aby nastawiÊ alarm najpierw nastrÛj stacjÍ i wyreguluj poziom g o no ci.
1Trzymaj±c wci niÍty przycisk ALARM A lub B (na przyk ad A dla alarmu radiowego a B dla brzÍczyka) naciskaj + lub â ponad TIME SET, dopÛki na wy wietlaczu nie pojawi siÍ prawid owe wskazanie czasu. Gdy zwolnisz
ALARM A lub B wskaºnik ALARM A lub B Ü:á przestanie pulsowaÊ i zapali siÍ a na wy wietlaczu pojawi siÍ wskazanie aktualnego czasu.
2Ustaw selektor ALARM A (dla radia) w pozycji RADIO lub ALARM B (dla brzÍczyka) w pozycji BUZZER.
Alarm rozlegnie siÍ o wyznaczonym czasie i wy ±czy siÍ automatycznie po 59 minutach.
•Je li nastawisz ALARM A oraz ALARM B na ten sam czas, rozlegnie siÍ tylko ALARM A.
•Aby wy ±czyÊ alarm, naci nij RADIO OFF/ ALARM RESET/OFF. Alarm rozlegnie siÍ nastÍpnego dnia o wyznaczonej porze.
•Aby anulowaÊ ktÛrykolwiek alarm, naci nij
RADIO OFF/ALARM RESET/OFF jednocze nie naciskaj±c ALARM A lub
ALARM B.
•Aby podrzemaÊ kilka minut, naci nij SNOOZE/ DATE/SLEEP OFF.
Alarm ucichnie lecz w ±czy siÍ ponownie po up ywie oko o 6 minut. Moøesz powtarzaÊ tÍ czynno Ê dowoln± ilo Ê razy.
•Aby wyregulowaÊ poziom g o no ci alarmu, obracaj VOL.
•Aby sprawdziÊ czas, na ktÛry nastawi e alarm, naci nij ALARM A lub ALARM B.
Nastawianie timera na dobranoc
DziÍki wbudowanemu timerowi na dobranoc, ktÛry wy ±cza radio automatycznie o wyznaczonym czasie moøesz zasypiaÊ s uchaj±c audycji radiowych.
1Naci nij RADIO ON/SLEEP.
W ±czy siÍ radio. Wy ±czy siÍ ono po up ywie wyznaczonego czasu. Moøesz nastawiÊ timer na dobranoc na 90, 60, 45, 30 oraz 15 minut. Kaøde naci niÍcie zmienia wy wietlenie jak pokazano niøej.
Aktualny czas |
|
|
On (W ±czone) |
|
90 |
||||||||
|
|
|
|||||||||||
|
|
15 |
|
|
30 |
|
45 |
|
60 |
|
|
BÍdziesz odbieraÊ radio przez wyznaczony czas, nastÍpnie radio siÍ wy ±czy.
•Aby wy ±czyÊ radio przed up ywem wyznaczonego czasu, naci nij SNOOZE/ DATE/SLEEP OFF.
¶rodki ostroøno ci
•Uøywaj ºrÛde zasilania podanych w czÍ ci ÜDane techniczneá.
•Tabliczka znamionowa wskazuj±ca napiÍcie operacyjne, itp. umieszczona jest na spodzie adaptera pr±du zmiennego.
•Aby od ±czyÊ przewÛd zasilania pr±dem zmiennym, ci±gnij za wtyk, nie za sam przewÛd.
•Zestaw nie jest od ±czony od ºrÛd a zasilania (sieci) dopÛki jest pod ±czony do gniazdaciennego, nawet je li sam zestaw jest wy ±czony.
•Nie ustawiaj urz±dzenia na miÍkkich powierzchniach (dywany, koce) ani blisko tkanin (zas ony, draperie), ktÛre blokuj± otwory wentylacyjne.
•Je li jakikolwiek przedmiot dostanie siÍ do wnÍtrza urz±dzenia od ±cz je od sieci i przed podjÍciem dalszej eksploatacji oddaj urz±dzenie do przegl±du w punkcie serwisowym.
•ObudowÍ czy Ê miÍkk± ciereczk±, zwiløon± roztworem agodnego detergentu.
•ZwrÛÊ uwagÍ, øe na niniejszym urz±dzeniu moøesz odbieraÊ tylko audycje radiowe i telewizyjne przeznaczone dla ogÛ u ludno ci. OdbiÛr radia policyjnego lub radia CB jest zabroniony.
Ostrzeøenie o wy adowaniu baterii
Gdy zamierzasz pozostawiÊ urz±dzenie nie pod ±czone do sieci przez d uøszy czas, wyjmij bateriÍ wspieraj±c±, aby unikn±Ê jej wy adowania lub uszkodzeÒ wynik ych z wycieku elektrolitu.
Je li masz jakiekolwiek pytania lub problemy dotycz±ce niniejszego zestawu prosimy, aby skonsultowa siÍ z najbliøszym dealerem firmy Sony.
Dane techniczne
Wy wietlenie czasu
24-godzinne
Zakres czÍstotliwo ci
FM: 87,6 â 107,5 MHz
AM: 531 â 1602 kHz
G o nik
W przybl. r. 5,7 cm (2 1/4 cala)
Moc wyj ciowa
120 mW (przy 10% zniekszta cenia harmonicznego)
Zasilanie
220-230V pr±du zmiennego, 50 Hz
Bateria wspieraj±ca 9 V pr±du sta ego, jedna bateria 6F22
Øywotno Ê baterii
W przybl. 36 godz. uøywaj±c baterii Sony S-006P(U)
Wymiary
W przybl. 271 × 63 × 68 mm (szer./wys./g Íb.) bez wystaj±cych czÍ ci i regulatorÛw
Masa
W przybl. 550 g (1 lb, 3 uncje) bez baterii
Konstrukcja i dane techniczne mog± ulec zmianom bez uprzedzenia