Sony GDM-200PS User Manual

0 (0)

3-861-050-14 (1)

Trinitron Color

Graphic Display

Operating Instructions

EN

 

 

 

 

 

 

Mode d’emploi

 

F

 

 

 

Manual de instrucciones

ES

 

 

 

 

 

 

 

 

 

 

 

C

 

 

 

 

 

 

GDM-200PS

© 1998 by Sony Corporation

Fiche Nema 5-15 broches
Type SVT ou SJT, minimum 3 × 18 AWG Maximum 15 pieds
Minimum 7 A, 125 V
As an ENERGY STAR Partner, Sony Corporation has determined that this product meets the ENERGY STAR guidelines for energy efficiency.
This monitor complies with the TCO 1992 guidelines for power saving when used with a computer equipped with VESA Display Power Management Signaling (DPMS).

Owner’s Record

The model and serial numbers are located at the rear of the unit. Record the serial number in the space provided below. Refer to these numbers whenever you call upon your dealer regarding this product.

Model No.

 

Serial No.

WARNING

To prevent fire or shock hazard, do not expose the unit to rain or moisture.

Dangerously high voltages are present inside the unit. Do not open the cabinet. Refer servicing to qualified personnel only.

FCC Notice

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

INFORMATION

This product complies with Swedish National Council for Metrology (MPR) standards issued in December 1990 (MPR II) for very low frequency (VLF) and extremely low frequency (ELF).

INFORMATION

Ce produit est conforme aux normes du Swedish National Council for Metrology de décembre 1990 (MPR II) en ce qui concerne les fréquences très basses (VLF) et extrêmement basses (ELF).

Hinweis

Dieses Gerät erfüllt bezüglich tieffrequenter (very low frequency) und tiefstfrequenter (extremely low frequency) Strahlung die Vorschriften des „Swedish National Council for Metrology (MPR)“ vom Dezember 1990 (MPR II).

INFORMACIÓN

Este producto cumple las normas del Consejo Nacional Sueco para Metrología (MPR) emitidas en diciembre de 1990 (MPR II) para frecuencias muy bajas (VLF) y frecuencias extremadamente bajas (ELF).

Hinweise

Aus ergonomischen Gründen wird empfohlen, die Grundfarbe Blau nicht auf dunklem Untergrund zu verwenden (schlechte Erkennbarkeit, Augenbelastung bei zu geringem Zeichenkontrast).

Aus ergonomischen Gründen (flimmern) sollten nur Darstellungen bei Vertikalfrequenzen ab 70 Hz (ohne Zeilensprung) verwendet werden.

Die Konvergenz des Bildes kann sich auf Grund des Magnetfeldes am Ort der Aufstellung aus der korrekten Grundeinstellung verändern. Zur Korrektur empfiehlt es sich deshalb, die Regler an der Frontseite für Konvergenz so einzustellen, daß die getrennt sichtbaren Farblinien für Rot, Grün und Blau bei z.B. der Darstellung eines Buchstabens zur Deckung (Konvergenz) gelangen.

Siehe hierzu auch die Erklärungen zu Konvergenz.

NOTICE

This notice is applicable for USA/Canada only.

If shipped to USA/Canada, install only a UL LISTED/CSA LABELLED power supply cord meeting the following specifications:

SPECIFICATIONS

Plug Type

Nema-Plug 5-15p

Cord

Type SVT or SJT, minimum 3 × 18 AWG

Length

Maximum 15 feet

Rating

Minimum 7 A, 125 V

NOTICE

Cette notice s’applique aux Etats-Unis et au Canada uniquement.

Si cet appareil est exporté aux Etats-Unis ou au Canada, utiliser le cordon d’alimentation portant la mention UL LISTED/CSA LABELLED et remplissant les conditions suivantes:

SPECIFICATIONS Type de fiche Cordon Longueur Tension

2

TABLE OF CONTENTS

Getting Started

Precautions ...........................................................................................................................

4

Identifying Parts and Controls ..........................................................................................

5

Setup ......................................................................................................................................

6

Automatically Adjusting the Size and Centering of the Picture ...................................

7

Selecting the On-screen Display Language .....................................................................

7

Selecting the Input Signal ...................................................................................................

8

Customizing Your Monitor

Adjusting the Picture Brightness and Contrast ...............................................................

9

 

Introducing the On-screen Display System .....................................................................

9

 

Using the CENTER On-screen Display ..........................................................................

10

 

Using the SIZE On-screen Display ..................................................................................

10

 

Using the GEOM (Geometry) On-screen Display .........................................................

11

 

Using the ZOOM On-screen Display ..............................................................................

12

 

Using the COLOR On-screen Display ............................................................................

12

 

...........................................................................Using the SCREEN On-screen Display

13

EN

...........................................................................Using the OPTION On-screen Display

15

 

Using the LANG (Language) On-screen Display .........................................................

17

 

Resetting the Adjustments ...............................................................................................

17

 

Technical Features

Preset and User Modes .....................................................................................................

18

Power Saving Function .....................................................................................................

19

Damper Wires ....................................................................................................................

19

Plug & Play .........................................................................................................................

19

Additional Information

Warning Messages .............................................................................................................

20

Troubleshooting .................................................................................................................

20

Self-diagnosis Function .....................................................................................................

22

Specifications ......................................................................................................................

22

Macintosh is a trademark licensed to Apple Computer, Inc., registered in the U.S.A. and other countries.

Windows® and MS-DOS are registered trademarks of Microsoft Corporation in the United States and other countries.

IBM PC/AT and VGA are registered trademarks of IBM Corporation of the U.S.A.

VESA is a trademark of Video Electronics Standard Association.

All other product names mentioned herein may be the trademarks or registered trademarks of their respective companies.

Furthermore, “™” and “®" are not mentioned in each case in this manual.

3

Getting Started

Precautions

Installation

Prevent internal heat build-up by allowing adequate air circulation. Do not place the monitor on surfaces (rugs, blankets, etc.) or near materials (curtains, draperies) that may block the ventilation holes.

Do not install the monitor near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, excessive dust, mechanical vibration or shock.

Do not place the monitor near equipment which generates magnetism, such as a transformer or high voltage power lines.

Maintenance

Clean the cabinet, panel and controls with a soft cloth lightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder or solvent, such as alcohol or benzine.

Do not rub, touch, or tap the surface of the screen with sharp or abrasive items such as a ballpoint pen or screwdriver. This type of contact may result in a scratched picture tube.

Clean the screen with a soft cloth. If you use a glass cleaning liquid, do not use any type of cleaner containing an anti-static solution or similar additive as this may scratch the screen’s coating.

Transportation

When you transport this monitor for repair or shipment, use the original carton and packing materials.

Use of the Tilt-Swivel

With the tilt-swivel, this monitor can be adjusted to the desired angle within 180° horizontally and 20° vertically. To turn the monitor vertically and horizontally, hold it at the bottom with both hands as illustrated below.

15°

90°

90°

5°

Warning on power connection

Use an appropriate power cord for your local power supply.

For the customers in the U.S.A.

If you do not use the appropriate cord, this monitor will not conform to mandatory FCC standards.

Examples of plug types

for 100 to 120 V AC

for 200 to 240 V AC

Before disconnecting the power cord, wait at least 30 seconds after turning off the power to allow the static electricity on the CRT display surface to discharge.

After the power has been turned on, the CRT is demagnetized (degaussed) for about 3 seconds. This generates a strong magnetic field around the metal frame, which may affect the data stored on magnetic tapes and disks near the bezel. Place magnetic recording equipment, tapes and disks away from this monitor.

The outlet should be installed near the equipment and be easily accessible.

4

Getting Started

Identifying Parts and Controls

See the pages in parentheses for further details.

Front

Rear

RESET

HD15 BNC

MENU

ASC

INPUT

1RESET (reset) button (page 17)

Resets the adjustments to the factory settings.

2ASC (auto sizing and centering) button (page 7)

Automatically adjusts the size and centering of the images.

3INPUT (input) button and HD15/BNC indicators (page 8)

Selects the HD15 or 5BNC video input signal. Each time you press this button, the input signal and corresponding indicator alternate.

4¨ (brightness) (./>) buttons (pages 8 –

17)

Adjust the picture brightness.

Function as the (./>) buttons when adjusting other items.

5MENU (menu) button (pages 8 – 17)

Displays the MENU OSD.

6> (contrast) (?//) buttons (pages 8 – 17,

22)

Adjust the contrast.

Function as the (?//) buttons when adjusting other items.

7u (power) switch and indicator (pages 19,

22)

Turns the monitor on or off.

The indicator lights up in green when the monitor is turned on, and either flashes in green and orange or lights up in orange when the monitor is in power saving mode.

8AC IN connector

Provides AC power to the monitor.

9 Video input 1 connector (HD15)

Inputs RGB video signals (0.700 Vp-p, positive) and

EN

SYNC signals.

 

 

 

 

 

 

 

 

 

 

5

4

 

3

2

1

 

 

 

 

10

9

8

7

6

 

 

 

 

15

14

13 12

11

 

 

 

 

 

 

 

 

 

 

 

Pin No.

Signal

 

 

 

Pin No.

Signal

 

 

1

Red

 

 

 

8

 

 

Blue Ground

 

 

2

Green

 

 

 

9

 

 

DDC + 5V*

 

 

 

(Composite

 

 

 

10

 

Ground

 

 

 

Sync on Green)

 

 

 

 

 

 

 

 

11

 

ID (Ground)

 

 

 

 

 

 

 

 

 

 

3

Blue

 

 

 

 

 

 

 

 

12

 

Bi-Directional

 

 

4

ID (Ground)

 

 

 

 

 

 

 

 

 

 

 

 

Data (SDA)*

 

 

5

DDC Ground*

 

 

13

 

H. Sync

 

 

6

Red Ground

 

 

 

14

 

V. Sync

 

 

7

Green Ground

 

 

15

 

Data Clock(SCL)*

 

 

*Display Data Channel (DDC) Standard of VESA

Video input 2 connector (5 BNC)

Inputs RGB video signals (0.700 Vp-p, positive) and SYNC signals.

5

Getting Started

Setup

Before using this monitor, check that the following items are included in your carton:

Monitor (1)

Power cord (1)

HD15 video signal cable (1)

Macintosh adapter (1)

Windows Monitor Information Disk (1)

Warranty card (1)

These operating instructions (1)

This monitor works with any IBM or compatible system equipped with VGA or greater graphics capability. Although this monitor works with other platforms running at horizontal frequencies between 30 and 92 kHz, including Macintosh and Power Macintosh systems, a cable adapter is required. Please consult your dealer for advice on which adapter is suitable for your needs.

Step 1: Connect the monitor to the

computer

With the computer switched off, connect the video signal cable to the monitor using the supplied HD15 video signal cable.

If you are using an IBM PC/AT or compatible computer, refer to the section below.

If you are using a Macintosh or compatible computer, refer to the following section, “Connecting to a Macintosh or compatible computer.”

If you want to use the 5 BNC connectors, refer to the section, “Connecting to the 5 BNC connectors.”

Connecting to an IBM PC/AT or compatible computer

If your PC system is not compatible with DDC2AB and DDC2B+

This monitor uses the No. 9 pin in the video signal connector for DDC2AB and DDC2B+ compatibility.

Some PC systems which are not compatible with either DDC2AB or DDC2B+ may not accept the No. 9 pin. If you are not sure whether your PC system accepts the No. 9 pin or not, use the HD15 (Female) - HD15 (Male without the No. 9 pin) adapter (not supplied). Make sure the male side (without the No. 9 pin) is connected to the computer.

Connecting to a Macintosh or compatible computer

 

 

to HD15

Macintosh or

 

 

compatible

 

 

computer

to video output

HD15 video

 

 

signal cable

 

 

 

 

(supplied)

 

Macintosh adapter

 

 

(supplied)

 

About the supplied Macintosh adapter

The supplied Macintosh adapter is compatible with Macintosh LC, Performa, Quadra, Power Macintosh and Power Macintosh G3 series computers.

Macintosh II series and some older versions of Power Book models may need an adapter with micro switches (not supplied).

Connecting to the 5 BNC connectors

to HD15

IBM PC/AT or

 

compatible

 

computer

to video output

HD15 video signal cable (supplied)

HD15 - HD15 adapter (not supplied)*

* The HD15 - HD15 adapter may be needed for some models.

6

to VIDEO IN R/G/B to SYNC IN HD/VD

Connect to the computer in the same way as for the HD15 connector.

To connect the 5 BNC connectors, use the SMF-400 video signal cable (sold separately). Connect the cables from left to right in the following order: Red–Green–Blue–HD–VD.

Notes

Do not short the pins of the video signal cable.

The DDC standard does not apply to the 5 BNC connectors. If you use the DDC standard, connect the HD15 connector to the computer with the supplied video signal cable.

Step 2: Connect the power cord

With the monitor switched off, connect one end of the power cord to the monitor and the other end to a power outlet.

 

 

 

to a power outlet

to AC IN

Power cord (supplied)

Step 3: Turn on the monitor and computer

The installation of your monitor is complete.

Note

If “OUT OF SCAN RANGE” or “NO INPUT SIGNAL” appears on the screen, see “Warning Messages” on page 20.

For customers using Windows 95/98

To maximize the potential of your monitor, install the new model information file from the supplied Windows Monitor Information Disk onto your PC.

This monitor complies with the “VESA DDC” Plug & Play standard. If your PC/graphics board complies with DDC, select “Plug & Play Monitor (VESA DDC)” or this monitor’s model name as the monitor type in the “Control Panel” of Windows 95/98. If your PC/graphics board has difficulty communicating with this monitor, load the Windows Monitor Information Disk and select this monitor’s model name as the monitor type.

For customers using Windows NT4.0

Monitor setup in Windows NT4.0 is different from Windows 95/98 and does not involve the selection of monitor type. Refer to the Windows NT4.0 instruction manual for further details on adjusting the resolution, refresh rate, and number of colors.

Getting Started

Automatically Adjusting the Size

and Centering of the Picture

By pressing the auto sizing and centering (ASC) button, the size and centering of the picture are automatically adjusted to fit the screen.

1Turn on the monitor and computer.

2Press the ASC button.

The picture is adjusted to fit the center of the screen.

ASC

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Notes

 

 

 

 

 

EN

• This function is intended for use with a computer running

 

Windows or similar graphic user interface software that

 

provides a full-screen picture. It may not work properly if the

 

background color is dark or if the input picture does not fill the

 

screen to the edges (such as an MS-DOS prompt).

 

The screen may go blank for a few seconds while performing the auto-sizing function. This is not a malfunction.

Although the signals for picture aspect ratio 5:4 (resolution: 1280 × 1024) do not fill the screen to the edges, the picture is

accurately displayed.

Selecting the On-screen Display

Language

If you need to change the OSD language, see “Using the LANG (Language) On-screen Display” on page 17.

The default setting is English.

7

Getting Started

Selecting the Input Signal

This monitor has two signal input connectors (HD15 and 5BNC) and can be connected to two computers. When the power of both computers is on, select the input signal you want to view as follows.

1Turn on the monitor and both computers.

2Press the INPUT button to select the HD15 or 5BNC input signal.

Each time you press the INPUT button, the input signal and corresponding indicator alternate.

HD15 BNC INPUT

Selecting the INPUT signal mode

This monitor has two modes of input signal selection, “AUTO” and “MANUAL.”

When “AUTO” is selected

If no signal is input from the selected connector, the monitor automatically selects the other connector’s signal. When you restart the computer you want to view, or that computer is in power saving mode, the monitor may automatically select the other connector’s signal. This is because the monitor switches from the interrupted signal to the constant signal. If this happens, manually select the desired signal using the INPUT button.

When “MANUAL” is selected

Even if no signal is input from the selected connector, the monitor does not select the other connector’s signal.

1Press the MENU button.

The MENU OSD appears.

MENU

MENU

 

OK

MENU

COLOR

CENTER SCREEN

GEOM

EXIT

ZOOM

LANG

SIZE

OPTION

2Press the ¨./>and >?//buttons to select “

OPTION,” and press the MENU button again.

The OPTION OSD appears.

OPTION

 

 

ON

ZZ...

1 MIN

 

 

UNLOCK

MANUAL DEGAUSS

3 Press the ¨./>buttons to select “ (INPUT).”

OPTION

AUTO MANUAL

ZZ...

1 MIN

 

 

UNLOCK

 

INPUT

4Press the >?//buttons to select “AUTO” or

“MANUAL.”

The OPTION OSD automatically disappears after about 30 seconds.

To close the OSD, press the MENU button again.

For more information on using the OSD, see “Introducing the On-screen Display System” on page 9.

8

 

 

 

 

 

 

 

 

Customizing Your Monitor

 

Customizing Your Monitor

 

 

Before adjusting

 

 

 

 

 

 

 

 

 

Introducing the On-screen

 

• Connect the monitor and the computer, and turn them on.

 

 

• Select “

 

LANG” in the MENU OSD, then select

 

Display System

 

 

 

 

 

“ENGLISH” (see page 17).

 

 

 

 

 

 

 

 

 

 

Most adjustments are made using the MENU OSD.

Adjusting the Picture Brightness

and Contrast

MENU OSD

Press the MENU button to display the MENU OSD.

Once the setting is adjusted, it will be stored in memory for

This MENU OSD contains links to the other OSDs described

below.

 

 

 

 

 

 

 

 

 

all input signals received.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1 Press the ¨ (brightness) ./>or >(contrast) ?//

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

buttons.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The BRIGHTNESS/CONTRAST OSD appears.

 

 

 

 

 

 

 

 

 

 

 

MENU

 

 

 

OK MENU

 

 

MENU

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

COLOR

 

CENTER

 

SCREEN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

BRIGHTNESS/CONTRAST

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

GEOM

EXIT

ZOOM

26

26

 

 

80.0kHz/

75Hz

LANG

SIZE OPTION

Horizontal Vertical

Frequency* Frequency*

2For brightness adjustment

Press the ¨./>buttons.

>. . . for more brightness

.. . . for less brightness

For contrast adjustment

Press the >?//buttons.

/. . . for more contrast ?. . . for less contrast

The OSD automatically disappears after about 3 seconds.

To reset, press the RESET button while the OSD is on. The brightness and contrast are both reset to the factory settings.

*The horizontal and vertical frequencies for the received input signal appear in the BRIGHTNESS/CONTRAST OSD.

EN

1 COLOR

Displays the COLOR OSD for adjusting the color temperature.

2 CENTER

Displays the CENTER OSD for adjusting the centering of the picture.

3 SCREEN

Displays the SCREEN OSD for adjusting the vertical and horizontal convergence, etc.

4 ZOOM

Displays the ZOOM OSD for enlarging and reducing the picture.

5 OPTION

Displays the OPTION OSD for adjusting the OSD position and degaussing the screen, etc.

6 SIZE

Displays the SIZE OSD for adjusting the picture size.

7 LANG

Displays the LANGUAGE OSD for selecting the language.

8 GEOM

Displays the GEOMETRY OSD for adjusting the picture rotation and pincushion, etc.

9EXIT

Closes the MENU OSD.

9

Customizing Your Monitor

Using the CENTER On-screen

Display

The CENTER settings allow you to adjust the centering of the picture.

Once the setting is adjusted, it will be stored in memory for the current input signal.

1Press the MENU button.

The MENU OSD appears.

MENU

2Press the ¨./>and >?//buttons to select “

CENTER,” and press the MENU button again.

The CENTER OSD appears.

CENTER

73

26

3For horizontal adjustment

Press the >?//buttons.

/. . . to move the picture right ?. . . to move the picture left

For vertical adjustment

Press the ¨./>buttons.

>. . . to move the picture up

.. . . to move the picture down

The OSD automatically disappears after about 30 seconds. To close the OSD, press the MENU button again.

To reset, press the RESET button while the OSD is on. The horizontal and vertical centerings are both reset to the factory settings.

Using the SIZE On-screen Display

The SIZE settings allow you to adjust the size of the picture. Once the setting is adjusted, it will be stored in memory for the current input signal.

1Press the MENU button.

The MENU OSD appears.

MENU

2Press the ¨./>and >?//buttons to select “

SIZE,” and press the MENU button again.

The SIZE OSD appears.

SIZE

73

26

3For horizontal adjustment

Press the >?//buttons.

/. . . to increase picture size ?. . . to decrease picture size

For vertical adjustment

Press the ¨./>buttons.

>. . . to increase picture size

.. . . to decrease picture size

The OSD automatically disappears after about 30 seconds. To close the OSD, press the MENU button again.

To reset, press the RESET button while the OSD is on.

The horizontal and vertical sizes are both reset to the factory settings.

10

Using the GEOM (Geometry) Onscreen Display

The GEOM (geometry) settings allow you to adjust the shape and orientation of the picture.

Once the rotation is adjusted, it will be stored in memory for all input signals received. All other adjustments will be stored in memory for the current input signal.

1Press the MENU button.

The MENU OSD appears.

MENU

2Press the ¨./>and >?//buttons to select “

GEOM,” and press the MENU button again.

The GEOMETRY OSD appears.

GEOMETRY

26

ROTATION

3Press the ¨./>buttons to select the item you want to adjust.

Customizing Your Monitor

4 Press the >?//buttons to adjust the settings.

For

Press

ROTATION /. . . to rotate the picture clockwise

?. . . to rotate the picture counterclockwise

PINCUSHION /. . . to expand the picture sides

?. . . to contract the picture sides

PIN BALANCE

/. . . to move the picture sides to the right

 

EN

 

 

 

 

?. . . to move the picture sides to the left

 

 

 

KEYSTONE

/. . . to increase the picture width at the

 

top

 

?. . . to decrease the picture width at the

 

top

 

 

 

KEY BALANCE

/. . . to move the top of the picture to

Select

 

To

 

the right

ROTATION

adjust the picture rotation

 

 

 

 

 

 

PINCUSHION

adjust the picture sides

?. . . to move the top of the picture to

 

 

 

 

the left

PIN BALANCE

adjust the picture side balance

 

 

 

 

 

 

KEYSTONE

adjust the picture width

 

 

 

 

 

 

 

 

 

 

KEY BALANCE

adjust the picture shape balance

 

 

 

 

 

 

The OSD automatically disappears after about 30 seconds.

To close the OSD, press the MENU button again.

To reset, press the RESET button while the OSD is on.

The selected item is reset to the factory setting.

11

Customizing Your Monitor

Using the ZOOM On-screen

Display

The ZOOM settings allow you to enlarge or reduce the picture.

Once the setting is adjusted, it will be stored in memory for the current input signal.

1Press the MENU button.

The MENU OSD appears.

MENU

2Press the ¨./>and >?//buttons to select “

ZOOM,” and press the MENU button again.

The ZOOM OSD appears.

ZOOM

H

 

 

 

 

 

 

 

 

26

 

 

 

 

 

 

 

 

V

 

 

 

 

 

 

 

73

3 Press the >?//buttons to adjust the picture zoom.

/. . . to enlarge the picture ?. . . to reduce the picture

Using the COLOR On-screen

Display

You can change the monitor’s color temperature. For example, you can change the colors of a picture on the screen to match the actual colors of the printed picture. Once the setting is adjusted, it will be stored in memory for all input signals received.

1Press the MENU button.

The MENU OSD appears.

MENU

2Press the ¨./>and >?//buttons to select “

COLOR,” and press the MENU button again.

The COLOR OSD appears.

COLOR

 

 

5000K

6500K

9300K

R

 

50

G

 

50

B

 

50

3Press the >?//buttons to select the color temperature.

The OSD automatically disappears after about 30 seconds. To close the OSD, press the MENU button again.

To reset, press the RESET button while the OSD is on.

Note

The picture zoom adjustment will stop as soon as either the horizontal or vertical size reaches its maximum or minimum value.

There are three color temperature modes in the OSD. The preset adjustments are:

5000K, 6500K, 9300K

12

4Fine tuning the color temperature

Press the ¨./>buttons to select R (red), G (green), or B (blue) and adjust by pressing the >?//buttons.

COLOR

 

 

1

6500K

9300K

R

 

76

G

 

50

B

 

50

The “5000K,” “6500K” or “9300K” disappears and the new color settings are memorized for each of the three color modes.

The color temperature modes change as follows: 5000Kn1, 6500Kn2, 9300Kn3

The OSD automatically disappears after about 30 seconds. To close the OSD, press the MENU button again.

To reset, press the RESET button while the OSD is on. The selected color temperature is reset to the factory settings.

Customizing Your Monitor

Using the SCREEN On-screen

Display

Adjust convergence settings to eliminate red or blue shadows that may appear around objects on the screen. Adjust the CANCEL MOIRE function to eliminate wavy or elliptical lines that may appear on the screen.

Once CANCEL MOIRE is adjusted, it will be stored in memory for the current input signal. All other adjustments will be stored in memory for all input signals received.

1Press the MENU button.

The MENU OSD appears.

MENU

2Press the ¨./>and >?//buttons to select “

SCREEN,” and press the MENU button again.

The SCREEN OSD appears.

EN

SCREEN

TOP

BOT 26

H CONVERGENCE

3Press the ¨./>buttons to select the item you want to adjust.

Select

To

 

 

 

 

 

 

 

 

 

adjust the horizontal convergence

 

 

 

 

H CONVERGENCE

 

 

 

 

 

 

 

 

 

 

adjust the vertical convergence

V CONVERGENCE

 

 

 

 

 

 

 

 

 

TOP

adjust the screen’s upper vertical

 

 

 

V CONVER TOP

convergence

 

 

 

 

 

 

 

 

BOT

adjust the screen’s lower vertical

 

 

 

V CONVER BOTTOM

convergence

 

 

 

 

 

 

 

 

 

(continued)

13

Customizing Your Monitor

Select

To

turn the moire cancellation function CANCEL MOIRE * “ON” or “OFF.” CANCEL MOIRE

must be “ON” for “ ADJ (MOIRE ADJUST)” to appear on the screen.

ADJ

adjust the degree of moire

MOIRE ADJUST

cancellation

 

*Moire is a type of natural interference which produces soft or wavy lines on your screen. It may appear due to interference between the regulated pattern of the picture from the input signal and the phosphor pitch pattern of the CRT.

Example of moire:

4 Press the >?//buttons to adjust the settings.

For

Press

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

/. . . to shift red shadows to the right

 

 

 

 

 

 

 

 

H CONVERGENCE

and blue shadows to the left

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

?. . . to shift red shadows to the left

 

 

 

 

and blue shadows to the right

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

/. . . to shift red shadows up and blue

 

 

 

 

V CONVERGENCE

shadows down

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

?. . . to shift red shadows down and

 

 

 

 

blue shadows up

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TOP

/. . . to shift red shadows up and blue

 

 

 

V CONVER TOP

shadows down

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

?. . . to shift red shadows down and

 

 

 

 

blue shadows up

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

For

Press

 

 

 

 

 

 

 

 

 

 

 

 

BOT

/. . . to shift red shadows up and blue

 

 

 

 

V CONVER BOTTOM

shadows down

 

 

 

 

 

 

 

 

 

 

 

 

 

?. . . to shift red shadows down and

 

 

 

blue shadows up

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

/. . . to turn CANCEL MOIRE “ON”

CANCEL MOIRE

 

OFF ON

 

 

 

?. . . to turn CANCEL MOIRE “OFF”

 

 

 

 

OFF ON

 

 

 

 

 

 

 

 

 

 

 

 

ADJ

/or ?. . . to adjust the screen until the

MOIRE ADJUST

moire is at a minimum

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

50

 

 

 

 

 

 

 

 

 

 

 

 

 

Note

The picture may become fuzzy when CANCEL MOIRE is set to “ON.”

The OSD automatically disappears after about 30 seconds. To close the OSD, press the MENU button again.

To reset, press the RESET button while the OSD is on. The selected item is reset to the factory setting.

14

Sony GDM-200PS User Manual

Using the OPTION On-screen

Display

The OPTION OSD allows you to manually degauss the screen and adjust settings such as the OSD position and power saving delay time. It also allows you to lock the controls.

Degaussing the screen

The monitor screen is automatically degaussed (demagnetized) when the power is turned on. You can also manually degauss the monitor.

1Press the MENU button.

The MENU OSD appears.

MENU

2Press the ¨./>and >?//buttons to select “

OPTION,” and press the MENU button again.

The OPTION OSD appears.

 

OPTION

 

 

ON

 

ZZ...

1 MIN

 

 

 

 

UNLOCK

 

MANUAL DEGAUSS

3 Press the ¨./>buttons to select “

 

(MANUAL

DEGAUSS).”

 

 

4Press the > /button.

The screen is degaussed for about 3 seconds.

If you need to degauss the screen a second time, wait for at least 20 minutes before repeating the steps above.

The OPTION OSD automatically disappears after about 30 seconds.

To close the OSD, press the MENU button again.

Customizing Your Monitor

Changing the on-screen display position

You can change the OSD position (for example, when you want to adjust the picture behind the OSD).

1Press the MENU button.

The MENU OSD appears.

MENU

2Press the ¨./>and >?//buttons to select “

OPTION,” and press the MENU button again.

The OPTION OSD appears.

OPTION

 

 

ON

ZZ...

1 MIN

 

 

UNLOCK

MANUAL DEGAUSS

3 Press the ¨./>buttons to select “

 

(OSD H

EN

 

 

POSITION)” or “

 

 

 

 

 

 

(OSD V POSITION).”

 

 

 

Select “ (OSD H POSITION)” to adjust the horizontal position.

OPTION

ZZ...

1 MIN

 

 

UNLOCK

 

OSD H POSITION

Select “ (OSD V POSITION)” to adjust the vertical position.

OPTION

AUTO

ZZ...

UNLOCK

OSD V POSITION

4Press the >?//buttons to move the OSD to the desired position.

The OPTION OSD automatically disappears after about 30 seconds.

To close the OSD, press the MENU button again.

To reset, press the RESET button while the OSD is on.

15

Customizing Your Monitor

Setting the power saving delay time

You can set the delay time before the monitor enters the power saving mode. See page 19 for more information on this monitor’s power saving capabilities.

Locking the controls

The control lock function disables all of the buttons on the front panel except the u(power) switch and MENU button.

1 Press the MENU button.

1Press the MENU button.

The MENU OSD appears.

MENU

2Press the ¨./>and >?//buttons to select “

OPTION,” and press the MENU button again.

The OPTION OSD appears.

OPTION

 

 

ON

ZZ...

1 MIN

 

 

UNLOCK

MANUAL DEGAUSS

3Press the ¨./>buttons to select “ ZZ... (PWR SAVE

DELAY).”

OPTION

 

 

AUTO

 

 

5 SEC

1 MIN

ZZ...

60 MIN

OFF

 

 

PWR SAVE DELAY

4 Press the >?//buttons to select the desired time.

The MENU OSD appears.

MENU

2Press the ¨./>and >?//buttons to select “

OPTION,” and press the MENU button again.

The OPTION OSD appears.

OPTION

 

 

ON

ZZ...

1 MIN

 

 

UNLOCK

MANUAL DEGAUSS

3Press the ¨./>buttons to select “ (CONTROL

LOCK).”

OPTION

 

AUTO

 

ZZ...

 

UNLOCK

LOCK

CONTROL LOCK

4 Press the >?//buttons to select “LOCK.”

When PWR SAVE DELAY is set to “OFF,” the monitor does not go into power saving mode.

The OPTION OSD automatically disappears after about 30 seconds.

To close the OSD, press the MENU button again.

To reset, press the RESET button while the OSD is on.

The OPTION OSD automatically disappears after about 30 seconds.

To close the OSD, press the MENU button again.

Once you select “LOCK,” you cannot select any items except “EXIT” and ” OPTION” in the MENU OSD.

If you press any button other than the u(power) switch and MENU button, the mark appears on the screen.

To cancel the control lock

Repeat steps 1 through 3 above and press the >?// buttons to select “UNLOCK.”

16

Using the LANG (Language) Onscreen Display

English, French, German, Spanish and Japanese versions of the OSDs are available.

1Press the MENU button.

The MENU OSD appears.

MENU

2Press the ¨./>and >?//buttons to select “

LANG,” and press the MENU button again.

The LANGUAGE OSD appears.

LANGUAGE

ENGLISH

FRANÇAIS

DEUTSCH

ESPAÑOL

3Press the ¨./>buttons to select the desired language.

ENGLISH: English, FRANÇAIS: French, DEUTSCH: German, ESPAÑOL: Spanish, or : Japanese.

The OSD automatically disappears after about 30 seconds. To close the OSD, press the MENU button again.

To reset to English, press the RESET button while the OSD is on.

Customizing Your Monitor

Resetting the Adjustments

Resetting an adjustment item

1Press the MENU, ¨./>and >?//buttons to select the OSD containing the item you want to reset.

MENU

2Press the ¨./>buttons to select the item you want to reset.

3 Press the RESET button.

RESET

EN

Resetting all of the adjustment data for

the current input signal

When there is no OSD displayed, press the RESET button.

All of the adjustments data for the current input signal is reset to the factory settings.

Note that adjustment data not affected by changes in input signal (OSD language, OSD position, input signal selection, power saving delay time and the control lock function) is not reset to the factory settings.

RESET

Resetting all of the adjustment data for all

input signals

Press and hold the RESET button for more than two seconds.

All of the adjustment data, including the brightness and contrast, is reset to the factory settings.

RESET

17

Technical Features

Preset and User Modes

This monitor has factory preset modes for the 20 most popular industry standards for true “plug and play” compatibility.

When a new input signal is entered, the monitor selects the appropriate factory preset mode and momentarily adjusts the phase calibration to provide a high quality picture to the center of the screen. The calibration is stored in memory and is immediately recalled whenever the same input signal is received.

Resolution Horizontal Vertical

No.

(dots × lines) Frequency Frequency Graphics Mode

1

640 × 350

31.5 kHz

70 Hz

MCGA

 

 

 

 

 

2

640 × 480

31.5 kHz

60 Hz

VGA-G

 

 

 

 

 

3

640 × 480

37.5 kHz

75 Hz

EVGA

 

 

 

 

 

4

640 × 480

43.3 kHz

85 Hz

VESA

 

 

 

 

 

5

720 × 400

31.5 kHz

70 Hz

VGA-Text

 

 

 

 

 

6

720 × 400

37.9 kHz

85 Hz

VESA

 

 

 

 

 

7

800 × 600

46.9 kHz

75 Hz

ESVGA

 

 

 

 

 

8

800 × 600

53.7 kHz

85 Hz

VESA

 

 

 

 

 

9

832 × 624

49.7 kHz

75 Hz

Macintosh

 

 

 

 

 

16” Color

 

 

 

 

 

 

10

1024

× 768

56.5 kHz

70 Hz

VESA

 

 

 

 

 

 

11

1024

× 768

60.0 kHz

75 Hz

EUVGA

 

 

 

 

 

 

12

1024

× 768

60.2 kHz

75 Hz

Macintosh

 

 

 

 

 

19” Color

 

 

 

 

 

 

13

1024

× 768

68.7 kHz

85 Hz

VESA

 

 

 

 

 

 

14

1152

× 864

67.5 kHz

75 Hz

VESA

 

 

 

 

 

 

15

1152

× 870

68.7 kHz

75 Hz

Macintosh

 

 

 

 

 

21” Color

 

 

 

 

 

 

16

1280

× 960

60.0 kHz

60 Hz

VESA

 

 

 

 

 

 

17

1280

× 960

85.9 kHz

85 Hz

VESA

 

 

 

 

 

 

18

1280

× 1024

64.0 kHz

60 Hz

VESA

 

 

 

 

 

 

19

1280

× 1024

80.0 kHz

75 Hz

VESA

 

 

 

 

 

 

20

1280

× 1024

91.1 kHz

85 Hz

VESA

 

 

 

 

 

 

For input signals that do not match one of the factory preset modes, the digital Multiscan technology of this monitor performs all of the adjustments necessary to ensure that a clear picture appears on the screen for any timing in the monitor’s frequency range. However, it may be necessary to fine tune the vertical/horizontal size and centering. Simply press the ASC button or adjust the monitor according to the adjustment instructions. The adjustments are stored automatically as a user mode and recalled whenever the corresponding input signal is received.

Recommended horizontal and vertical timing conditions

Horizontal sync width duty should be: >4.8% of total horizontal time.

Horizontal blanking width should be: >3.0 µsec. Vertical blanking width should be: > 450 µsec.

Note for Windows users

For Windows users, check your video board manual or the utility program which comes with your graphic board and select the highest available refresh rate to maximize monitor performance.

Adjusting the monitor’s resolution and color number

Adjust the monitor’s resolution and color number by referring to your computer’s instruction manual. The color number may vary according to your computer or video board. The color palette setting and the actual number of colors are as follows:

High Color (16 bit) n65,536 colors

True Color (24 bit) nabout 16.77 million colors In true color mode (24 bit), speed may be slower.

18

Power Saving Function

This monitor meets the power-saving guidelines set by VESA and Energy Star, as well as the more stringent NUTEK .

If the monitor is connected to a computer or video graphics board that is VESA DPMS (Display Power Management Signaling) compliant, the monitor will automatically reduce power consumption in three stages as shown below.

Technical Features

You can set the delay time before the monitor enters the power saving mode using the OSD. Set the time according to “Setting the power saving delay time” on page 16.

Note

If no video signal is input to the monitor, the “NO INPUT SIGNAL” message (page 20) appears. After the delay time has passed, the power saving function automatically puts the monitor into the active-off mode and the uindicator lights up orange. Once the horizontal and vertical sync signals are detected, the monitor automatically resumes its normal operation mode.

 

Power consumption

Screen

Horizontal

Vertical

Power consumption

Recovery time

u indicator

 

mode

 

sync signal

sync signal

 

 

 

 

 

 

 

 

 

 

 

1

Normal operation

active

present

present

≤ 120 W

Green

2

Standby (1st mode)

blank

absent

present

Approx. 60 W

Approx. 1 sec.

Green and orange

 

 

 

 

 

 

 

alternate

 

 

 

 

 

 

 

 

3

Suspend (2nd mode)

blank

present

absent

Approx. 8 W

Approx. 3 sec.

Green and orange

 

 

 

 

 

 

 

alternate

 

 

 

 

 

 

 

 

4

Active-off (3rd mode)

blank

absent

absent

Approx. 4 W

Approx. 15 sec.

Orange

5

Power-off

0 W

Off

Damper Wires

When viewing a white background, very thin horizontal lines may be visible on the screen as shown below. These lines are the shadows of the damper wires and are characteristic of CRTs that use aperture grilles. The wires are attached to the aperture grille on the inside of the Trinitron tube and prevent the vibration of the aperture grille.

Damper wires

EN

Plug & Play

This monitor complies with the DDC™1, DDC2B, DDC2AB and DDC2B+ Display Data Channel (DDC) standards of VESA.

When a DDC1 host system is connected, the monitor synchronizes with the V. CLK in accordance with the VESA standards and outputs the EDID (Extended Display Identification Data) to the data line.

When a DDC2B, DDC2AB or DDC2B+ host system is connected, the monitor automatically switches to the appropriate standard.

DDC™ is a trademark of the Video Electronics Standard Association.

Note

When using Windows 95/98, the DDC standard does not apply to the 5 BNC connectors. If you use the DDC standard, connect the HD15 connector to the computer with the supplied video signal cable.

19

Loading...
+ 44 hidden pages