Snapper M300919B, M250819BE, M280919B, M281019BE, M301019BE User Manual

0 (0)

Safety Instructions & Operator’s Manual for

REAR ENGINE RIDING MOWER

SERIES 19

MODEL

M250819BE

M280919B

M281019BE

M300919B

M301019BE

MODEL NUMBER EXPLANATION

 

 

M

28

 

10

19

 

B

E

 

 

 

MIDDLE MARKET

 

 

 

 

 

 

 

 

 

 

 

 

ENGINE OPTIONS

CUTTING WIDTH

 

 

 

 

 

 

 

 

 

 

 

 

 

ENGINE TYPE

ENGINE HP

 

 

 

 

 

 

 

 

 

 

 

 

SERIES DESIGNATION

 

 

 

 

 

 

 

 

 

 

 

M - Middle Market

25 - 25” Cutting Deck

 

08 -

8.0 HP Engine

 

19 - Series

 

 

B - Briggs Engine

E - Electric Start

 

28 - 28” Cutting Deck

 

09 -

9.0 HP Engine

 

Designation

 

 

 

 

 

30 - 30” Cutting Deck

 

10 - 10.0 HP Engine

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Thank you for buying a SNAPPER Product! Before operating your machine, read this manual carefully and pay particular attention to the “IMPORTANT SAFETY INSTRUCTIONS” on Pages 2 & 3. Remember that all power equipment can be dangerous if used improperly. Also keep in mind that SAFETY requires careful use in accordance with the operating instructions and common sense!

COPYRIGHT © 1999

SNAPPER INC.

ALL RIGHTS RESERVED

MANUAL No. 7-1947 (REV. 1, 8/20/99)

IMPORTANT SAFETY INSTRUCTIONS

WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply with the following SAFETY instructions could result in serious injury or death to the operator or other persons. The owner of the machine must understand these instructions and must allow only persons who understand these instructions to operate machine. Each person operating the machine must be of sound mind and body and must not be under the influence of any substance, which might impair vision, dexterity or judgment. If you have any questions pertaining to your machine which your dealer cannot answer to your satisfaction, call or write the Customer Service Department at SNAPPER, McDonough, Georgia 30253. Phone: (1-800-935-2967).

PROTECTION FOR CHILDREN

Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine and the mowing activity. Never assume that children will remain where you last saw them.

1.KEEP children out of the mowing area and under the watchful care of a responsible adult.

2.DO NOT allow children in yard when machine is operated (even with the blade OFF).

3.DO NOT allow children or others to ride on machine or on attachments (even with the blades OFF). They may fall and be seriously injured.

4.DO NOT allow pre-teenage children to operate machine.

5.ALLOW only responsible adults & teenagers with mature judgment under close adult supervision to operate machine.

6.DO NOT operate blades in reverse. STOP BLADES. LOOK and SEE behind and down for children, pets and hazards before and while backing.

7.USE EXTRA CARE when approaching blind corners, shrubs, trees, or other objects that may obscure vision.

PROTECTION AGAINST TIPOVERS

Slopes are a major factor related to loss-of-control and tip-over accidents, which can result in severe injury or death. All slopes require extra CAUTION. If you cannot back up the slope or if you feel uneasy on the slope, DO NOT mow it. Use extra care with grass catchers or other attachments; these affect the handling and the stability of the machine.

1.DO NOT operate machine on slopes exceeding 15 degrees (27% grade).

2.Exercise EXTREME CAUTION on slopes above 10 degrees (18% grade). Turn blades OFF when traveling uphill. Use a slow speed and avoid sudden or sharp turns.

3.DO NOT operate machine back and forth across face of slopes. Operate up and down. Practice on slopes with blades off.

4.AVOID uphill starts. If machine stops going uphill or tires lose traction, turn blades OFF and back slowly down the slope.

PROTECTION AGAINST TIPOVERS

(Continued From Previous Column)

5.STAY ALERT for holes and other hidden hazards. Tall grass can hide obstacles. Keep away from ditches, washouts, culverts, fences and protruding objects.

6.KEEP A SAFE DISTANCE (at least 3 feet) away from edge of ditches and other drop offs. The machine could turn over if an edge caves in.

7.Always begin forward motion slowly and with caution.

8.Use weights or a weighted load carrier in accordance with instructions supplied with a grass catcher. DO NOT operate machine on slopes exceeding 10 degrees (18% grade) when equipped with grass catcher.

9.DO NOT put your foot on the ground to try to stabilize the machine.

10.DO NOT operate machine on wet grass. Reduced traction could cause sliding.

11.DO NOT operate machine under any condition where traction, steering or stability is doubtful.

PREPARATION

1.Read, understand, and follow instructions and warnings in this manual and on the machine, engine and attachments. Know the controls and the proper use of the machine before starting.

2.Only mature, responsible persons shall operate the machine and only after proper instruction.

3.Data indicates that operators age 60 and above, are involved in a large percentage of mowerrelated injuries. These operators should evaluate their ability to operate the mower safely enough to protect themselves and others from serious injury.

4.Handle fuel with extra care. Fuels are flammable and vapors are explosive. Use only an approved fuel container. DO NOT remove fuel cap or add fuel with engine running. Add fuel outdoors only with engine stopped and cool. Clean spilled fuel from machine. DO NOT smoke.

5.Practice operation of machine with BLADES OFF to learn controls and develop skills.

6.Check the area to be mowed and remove all objects such as toys, wire, rocks, limbs and other objects that could cause injury if thrown by blade or interfere with mowing.

2

IMPORTANT SAFETY INSTRUCTIONS

PREPARATION

(Continued From Previous Page)

7.Keep people and pets out of mowing area. Immediately STOP blades, STOP engine, and STOP machine if anyone enters the area.

8.Check shields, deflectors, switches, blade controls and other safety devices frequently for proper operation and location.

9.Make sure all safety decals are clearly legible. Replace if damaged.

10.Protect yourself when mowing and wear safety glasses, long pants and substantial footwear.

11.Know how to STOP blades and engine quickly in preparation for emergencies.

12.Use extra care when loading or unloading the machine into a trailer or truck.

13.Check grass catcher components frequently for signs of wear or deterioration and replace as needed to prevent injury from thrown objects going through weak or worn spots.

OPERATION

1.Mount and dismount machine from left side.

2.Start engine from operator's seat, if possible. Make sure blades are OFF and parking brake is set.

3.DO NOT leave machine with engine running. STOP engine, STOP blades, SET brake, and Remove key before leaving operators position of any reason.

4.DO NOT operate machine unless properly seated with feet on feet rests or pedal(s).

5.STOP BLADES and ENGINE and make sure blades have stopped before removing grass catcher or unclogging mower to prevent loss of fingers or hand.

6.Blades must be OFF except when cutting grass. Set blades in highest position when mowing over rough ground.

7.Keep hands and feet away from rotating blades underneath deck. DO NOT place foot on ground while BLADES are ON or machine is in motion.

8.DO NOT operate machine without entire grass catcher or guards in place. DO NOT point discharge at people, passing cars, windows or doors.

9.Slow down before turning.

10.Watch out for traffic when near or crossing roadways.

11.STOP engine immediately after striking an obstruction. Inspect machine and repair damage before resuming operation.

12.Operate machine only in daylight or with good artificial light.

13.Move joystick (if equipped) SLOWLY to maintain control during speed and directional changes.

OPERATION

(Continued From Previous Column)

14.Exercise CAUTION when pulling loads. Limit loads to those you can safely control and attach loads to hitch plate as specified with SNAPPER attachment instructions.

15.DO NOT operate engine in enclosed areas. Engine exhaust gases contain carbon monoxide, a deadly poison.

MAINTENANCE

1.DO NOT store machine or fuel container inside where fumes may reach an open flame, spark or pilot light such as in a water heater, furnace, clothes dryer or other gas appliance. Allow engine to cool before storing machine in an enclosure. Store fuel container out of the reach of children in a well ventilated, unoccupied building.

2.Keep engine free of grass, leaves or excess grease to reduce fire hazard and engine overheating.

3.When draining fuel tank, drain fuel into an approved container outdoors and away from open flame.

4.Check brakes frequently; adjust, repair or replace as needed.

5.Keep all bolts, nuts and screws properly tight. Check that all cotter pins are in proper position.

6.Always provide adequate ventilation when running engine. Exhaust gases contain carbon monoxide, an odorless and deadly poison.

7.Disconnect negative (black) cable from battery before performing maintenance or service. Cranking engine could cause injury.

8.DO NOT work under machine without safety blocks.

9.Service engine and make adjustments only when engine is stopped. Remove spark plug wire(s) from spark plug(s) and secure wire(s) away from spark plug(s).

10.DO NOT change engine governor speed settings or overspeed engine.

11.Lubricate machine at intervals specified in manual to prevent controls from binding.

12.Mower blades are sharp and can cut. Wrap the blades or wear heavy leather gloves and use CAUTION when handling them.

13.DO NOT test for spark by grounding spark plug next to spark plug hole; spark plug could ignite gas exiting engine.

14.Have machine serviced by an authorized SNAPPER dealer at least once a year and have the dealer install any new safety devices.

15.Use only genuine SNAPPER replacement parts to assure that original standards are maintained.

3

TABLE OF CONTENTS

 

IMPORTANT SAFETY INSTRUCTIONS..........................................................

2-3

TABLE OF CONTENTS ......................................................................................

4

SECTION 1 - FAMILIARIZATION .......................................................................

5

SECTION 2 - OPERATING INSTRUCTIONS.................................................

6-11

Pre-start Checklist .........................................................................................................

6

Operator’s Seat Adjustment..........................................................................................

6

Starting & Stopping Engine, Blades & Wheel Drive ..............................................

7-10

Starting & Stopping Mower Blades .........................................................................

9-10

Starting & Stopping Wheel Drive.............................................................................

9-10

Parking Brake ...............................................................................................................

11

Cutting Height Adjustment..........................................................................................

11

SECTION 3 - MAINTENANCE INSTRUCTIONS .........................................

12-17

Service – After First 5 Hours .......................................................................................

12

Change Engine Oil ....................................................................................................

12

Service Engine Air Cleaner ......................................................................................

12

Check Mower Blade ..................................................................................................

12

Check Blade Drive Belt.............................................................................................

13

Blade Brake ...............................................................................................................

13

Service Brake / Park Brake.......................................................................................

13

Check Interlock System............................................................................................

13

Lubrication – Grease Fittings ..................................................................................

14

Service - Every 25 Operating Hours ......................................................................

14-15

Battery Fluid Level ....................................................................................................

14

Mower Deck Levelness.............................................................................................

14

Clean Mower Deck ....................................................................................................

14

Mower Blade Spindle - Lubrication .........................................................................

14

Mower Deck Linkage – Lubrication.........................................................................

14

Front Wheel Bearing - Lubrication .....................................................................

14-15

Rear Axle Bearing – Lubrication..............................................................................

15

Differential / Chain Case - Lubrication....................................................................

15

Service – Annually........................................................................................................

16

Engine ........................................................................................................................

16

Fuel Filter ..................................................................................................................

16

Every Two Years...........................................................................................................

16

Storage - Out of Season ..............................................................................................

16

Removing Fuel Tank ....................................................................................................

16

SECTION 4- ADJUSTMENTS AND REPAIR ...............................................

17-25

Engine Adjustments & Repair.....................................................................................

17

Mower Deck & Component Adjustments...................................................................

17

Mower Drive Belt Adjustment .....................................................................................

17

Blade Brake Adjustment ..............................................................................................

18

Mower Deck Adjustment (Side to Side Levelness) ..............................................

18-19

Mower Deck Adjustment (Front to Rear Levelness) .................................................

19

Rear Engine Rider Drive Components .......................................................................

20

Wheel Brake Adjustment .............................................................................................

20

Mower Blade Replacement..........................................................................................

21

Blade Sharpening.........................................................................................................

21

Blade Drive Belt Removal/Replacement ....................................................................

22

Battery Removal, Replacement, Service...............................................................

23-25

ACCESSORIES ................................................................................................

25

TROUBLESHOOTING .................................................................................

26-27

MAINTENANCE SCHEDULE............................................................................

28

MAINTENANCE/REPLACEMENT PARTS........................................................

29

WARRANTY .....................................................................................................

30

PRIMARY MAINTENANCE..........................................................................

31-34

4

Snapper M300919B, M250819BE, M280919B, M281019BE, M301019BE User Manual

Section 1 - FAMILIARIZATION

FUEL TANK

REAR BUMPER

TRANSMISSION

SHIFT LEVER

MOWER BELT

COVER

DISCHARGE

DEFLECTOR

FUEL

FILLER CAP

VENT

OPERATOR’S

SEAT

STEERING

WHEEL

ENGINE

SPEED

CONTROL

DECK LIFT

LEVER

CLUTCH/BRAKE

PEDAL

BLADE

LEVER

BLADE

PEDALS PARK BRAKE

MOWER LATCH

DECK

FIGURE 1.1

1.1 INTRODUCTION

This manual has been prepared for the operator’s of the SNAPPER Rear Engine Rider. Its purpose, aside from recommending standard operating procedures and routine service requirements, is to promote SAFETY through the use of accepted operating practices. Read, Understand and Follow the IMPORTANT SAFETY INSTRUCTIONS on Pages 2 & 3 of this manual and All SAFETY messages on the Rear Engine Rider and its attachments before operating.

1.2 NOMENCLATURE

The nomenclature drawing above, Figure 1.1, shows the essential parts of the SNAPPER Rear Engine Rider. It is recommended that all operator’s of this equipment become thoroughly familiar with the controls, components, and operation of this machine before operating. Specific details involving the engine are found in the separate engine owner’s manual. Study these manuals before operating and keep both handy for future reference.

5

Section 2 - OPERATING INSTRUCTIONS

2.1PRE-START CHECK LIST

Make the following checks and perform the service required before each start-up.

2.1.1.Check tires and add or release air as needed to bring pressure to 12 psi in front and 12 psi in rear tires.

2.1.2.Check guards, deflectors and covers to make sure all are in place and securely tightened.

2.1.3.Check engine oil and add oil as needed to bring level up to the FULL mark. Refer to engine owner’s manual for oil specifications. See Figure 2.1.

SAFE

LEVEL

AREA

2.2 OPERATOR’S SEAT ADJUSTMENT 2.2.1. FRONT TO REAR ADJUSTMENT

1. With the engine stopped, loosen the two adjusting knobs and move seat to desired position. After adjustment, tighten knobs securely. If seat does not move after loosening knobs, it may be necessary to loosen the 5/16” patch lock screws located at the rear of the seat using a 1/2 inch wrench. See Figure 2.3.

OPERATOR’S

SEAT

ADJUSTING

KNOBS

FIGURE 2.1

2.1.4.Adjust seat as needed to most comfortable position. Refer to Section “OPERATOR’S SEAT ADJUSTMENT”.

2.1.5.Check blade control to insure it works freely. If blade pedals are depressed, blade lever can be moved manually from “ON” to “OFF” to stop blade.

2.1.6.Clean exterior surfaces of cutting deck and engine of any accumulation of dirt, grass, oil, etc. Keep engine air intake screen and cooling fins clear at all times.

2.1.7.Add fuel to tank after pushing the Rear Engine Rider outside where fumes can dissipate. Make sure fuel filler cap is tight and vent is open after refueling. Refer to engine owner’s manual for fuel specifications. See Figure 2.2.

5/16” PATCH LOCK SCREWS (DO NOT OVERTIGHTEN)

FIGURE 2.3

FUEL

OPEN

VENT

FILLER

 

CAP

 

FUEL

TANK

FIGURE 2.2

6

Section 2 - OPERATING INSTRUCTIONS

2.3 STARTING & OPERATION

2.3.1. ENGINE (ELECTRIC START)

IMPORTANT: When the ignition key is turned to “START”, the engine will turn over, but willnot start unless the Clutch/Brake pedal is pressed all the way down, the Blade Lever is in the “Off” position (See Figure 2.5).The operator should be in the seat. Start engine as follows:

1. Move transmission shift lever to (N) Neutral position. DO NOT start engine with transmission shift lever in a drive position.

WARNING

It is possible to start engine with transmission shift lever in a drive position. Follow starting instructions carefully.

2. Make certain the Blade Lever is in the “Off” position. See Figure 2.4.

BLADE LEVER

SHOWN IN “OFF”

POSITION

RELEASE

BLADE

PEDALS

FIGURE 2.4

3.Press Clutch/Brake Pedal all the way down and hold while starting engine. See Figure 2.5.

4.Open vent on fuel filler cap by turning counterclockwise. IMPORTANT: Failure to open vent on the fuel filler cap can cause engine to stall. See Figure 2.2.

5.Move engine speed control to the choke position to start a cold engine. See Figure 2.6.

6.Turn key to the “START” position until engine starts. See Figure 2.7. NOTE: If after 5 seconds of cranking the engine and it does not start, release the key, make sure the Clutch/Brake Pedal is fully depressed and attempt starting again after waiting for approximately 20 seconds.

7.After engine starts, move engine speed control to the “FAST” position, allow a brief warm-up until engine runs smooth.

TO START ENGINE,

PUSH CLUTCH/BRAKE

PEDAL ALL THE WAY

DOWN

PARKING

BRAKE

LATCH

FIGURE 2.5

CHOKE

POSITION

ENGINE

SPEED

CONTROL

FIGURE 2.6

KEY

FIGURE 2.7 (Continued on Next Page)

7

Section 2 - OPERATING INSTRUCTIONS

2.3STARTING & OPERATION

2.3.1. ENGINE (ELECTRIC START) (Continued)

8. Should the battery be too weak to start the engine, Refer to Section “ENGINE (MANUAL START)” to manually start the electric start engines.

2.3.2. ENGINE (MANUAL START)

IMPORTANT: When the ignition key is turned to “RUN”, and the recoil handle is pulled, the engine will turn over, but will not start unless the Clutch/Brake Pedal is pressed all the way down with Parking Brake engaged (See Figure 2.8) and the Blade Lever is in the “Off” position (See Figure 2.4). Start engine as follows:

1. Move transmission shift lever to (N) Neutral position. DO NOT start engine with transmission shift lever in a drive position.

WARNING

It is possible to start engine with transmission shift lever in a drive position. Follow starting instructions carefully.

2.Make certain the Blade Lever is in the “Off” position. See Figure 2.4.

3.Press Clutch/Brake Pedal all the way down, move Parking Brake Latch over and release the Clutch/Brake Pedal to set Parking Brake. See Figure 2.8.

TO START ENGINE,

PUSH CLUTCH/BRAKE

PEDAL ALL THE DOWN

5.Move engine speed control to the choke position to start a cold engine. See Figure 2.6

6.Turn key to “RUN” position. See Figure 2.9.

KEY

FIGURE 2.9

7.Pull starter rope with a smooth, even motion until engine starts. Always guide the starter rope back into the recoil housing. Never allow rope to snap back. After Engine starts, move engine speed control to the “FAST” position.

8.Allow a brief warm-up until engine runs smooth.

MOVE

PARKING

BRAKE

LATCH

OVER

FIGURE 2.8

4. Open vent on fuel filler cap by turning counterclockwise. NOTE: Failure to open vent on the fuel filler cap can cause engine to stall. See Figure 2.2.

8

Section 2 - OPERATING INSTRUCTIONS

WARNING

Once blade is disengaged, it should come to a complete stop in 3 seconds or less. If the blade continues to rotate after 3 seconds, the blade brake must be adjusted. Refer to Section “BLADE BRAKE ADJUSTMENT” for adjustment procedures or return machine to an authorized SNAPPER dealer for adjustment. DO NOT CONTINUE to operate machine until blade brake is adjusted and functioning properly.

2.3STARTING & OPERATION 2.3.3. MOWER BLADE

1.With engine running, move engine speed control to the “FAST” position.

2.Move blade lever forward to the “ON” position, then depress blade pedals to hold blade lever in the “ON” position. See Figure 2.10.

IMPORTANT: You cannot engage the blade lever if the blade pedal is depressed first.

BLADE LEVER

SHOWN IN “ON”

POSITION

BLADE

PEDALS

SHOWN

DEPRESSED

FIGURE 2.10

2.3.4. WHEEL DRIVE

1.With engine running, adjust engine speed control to “FAST” position.

2.Depress clutch/brake pedal. See Figure 2.11.

3.Place transmission shift lever in the notch for 1st speed. See Figure 2.12.

4.Release clutch/brake pedal to begin desired ground speed.

5.During forward motion, the transmission shift lever may be placed in any desired forward speed without depressing the clutch/brake pedal.

NOTE: For best cutting results, move the transmission shift lever into a slow forward speed and the engine speed control to a fast position. This combination will allow the mower blades to lift the grass while cutting smoothly and evenly.

WARNING

DO NOT operate blades in reverse. STOP BLADES. LOOK and SEE behind and down for children, pets and hazards before and while backing.

DEPRESS

CLUTCH/BRAKE

PEDAL

FIGURE 2.11

TRANSMISSION

SHIFT LEVER (MOVE

TO DESIRED SPEED)

FIGURE 2.12

9

Section 2 - OPERATING INSTRUCTIONS

WARNING

 

DO NOT leave machine with the engine running.

CLUTCH/BRAKE

Stop engine. Stop blade. Shift to neutral. Engage

parking brake. Remove key.

PEDAL

 

2.4STOPPING - ENGINE, WHEEL DRIVE, BLADE 2.4.1. ENGINE

1. Stop engine by turning key to the “OFF” position. See Figure 2.13.

TURN TO “OFF” POSITION

PARK BRAKE

LATCH SHOWN

ENGAGED

KEY

FIGURE 2.14

FIGURE 2.13

2.4.2. WHEEL DRIVE

1. Stop motion of Rear Engine Rider by pushing clutch/brake pedal all the way “DOWN” to apply brake. See Figure 2.14.

WARNING

Once blade is disengaged, it should come to a complete stop in 3 seconds or less. If the blade continues to rotate after 3 seconds, the blade brake must be adjusted. Refer to Section “BLADE BRAKE ADJUSTMENT” for adjustment procedures or return machine to an authorized SNAPPER dealer for adjustment. DO NOT CONTINUE to operate machine until blade brake is adjusted and functioning properly.

2.4.3. MOWER BLADE

1. Stop mower blade by releasing blade pedals or moving blade lever rearward to the “OFF” position. See Figure 2.15.

BLADE LEVER (SHOWN IN “OFF” POSITION)

BLADE

PEDALS

FIGURE 2.15

(Continued on Next Page)

10

Section 2 - OPERATING INSTRUCTIONS

2.4 STOPPING - ENGINE, WHEEL DRIVE, BLADE 2.4.4. PARK BRAKE

1. Engage park brake by pushing clutch/brake pedal “DOWN” and moving the park brake latch to the “ENGAGED” position. While holding the park brake latch “ENGAGED”, release clutch/brake pedal to set park brake. See Figure 2.16.

2.5.CUTTING HEIGHT ADJUSTMENT

1. Adjust cutting height as desired to any one of five positions using deck lift lever. Move deck lift lever up or down to desired cutting height and then move over to secure in the height of cut notch. See Figure 2.18.

WARNING

DO NOT park the machine on slopes.

CLUTCH/BRAKE

PEDAL

PARK BRAKE

LATCH SHOWN

ENGAGED

FIGURE 2.16

2. Release park brake by pushing down on the clutch/brake pedal, parking brake latch will move to the “OFF” position unassisted. See Figure 2.17.

CLUTCH/BRAKE

PEDAL SHOWN

DISENGAGED

HEIGHT OF CUT

NOTCHES

DECK LIFT

LEVER

FIGURE 2.18

PARK BRAKE

LATCH SHOWN

IN “OFF”

POSITION

FIGURE 2.17

11

Loading...
+ 25 hidden pages