Loading...
TigerSwitch 10/100
24-Port 10/100 Mbps
Fast Ethernet Managed Switch
24 auto-MDI/MDI-X 10/100BASE-TX ports
4 Gigabit RJ-45/SFP combination ports
Non-blocking switching architecture
Spanning Tree Protocol, and Rapid STP
Up to 8 LACP or static trunks
CoS support through four priority queues
Full support for VLANs with GVRP
IGMP multicast filtering and snooping
Support for jumbo frames up to 9 KB
Manageable via console, Web, SNMP, RMON
Installation Guide
Installationsanleitung
SMC6128L2
TigerSwitch 10/100
Installation Guide
From SMC’s Tiger line of feature-rich workgroup LAN solutions
20 Mason |
|
Irvine, CA 92618 |
March 2007 |
Phone: (949) 679-8000 |
Pub. # 150200060900A |
Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable. However, no responsibility is assumed by SMC for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SMC. SMC reserves the right to change specifications at any time without notice.
Copyright © 2007 by SMC Networks, Inc.
20 Mason
Irvine, CA 92618
All rights reserved. Printed in Taiwan
Trademarks:
SMC is a registered trademark; and EZ Switch, TigerStack and TigerSwitch are trademarks of SMC Networks, Inc. Other product and company names are trademarks or registered trademarks of their respective holders.
LIMITED WARRANTY
Limited Warranty Statement: SMC Networks, Inc. (“SMC”) warrants its products to be free from defects in workmanship and materials, under normal use and service, for the applicable warranty term. All SMC products carry a standard 90-day limited warranty from the date of purchase from SMC or its Authorized Reseller. SMC may, at its own discretion, repair or replace any product not operating as warranted with a similar or functionally equivalent product, during the applicable warranty term. SMC will endeavor to repair or replace any product returned under warranty within 30 days of receipt of the product.
The standard limited warranty can be upgraded to a Limited Lifetime* warranty by registering new products within 30 days of purchase from SMC or its Authorized Reseller. Registration can be accomplished via the enclosed product registration card or online via the SMC web site. Failure to register will not affect the standard limited warranty. The Limited Lifetime warranty covers a product during the Life of that Product, which is defined as the period of time during which the product is an “Active” SMC product. A product is considered to be “Active” while it is listed on the current SMC price list. As new technologies emerge, older technologies become obsolete and SMC will, at its discretion, replace an older product in its product line with one that incorporates these newer technologies. At that point, the obsolete product is discontinued and is no longer an “Active” SMC product. A list of discontinued products with their respective dates of discontinuance can be found at: http://www.smc.com/index.cfm?action=customer_service_warranty.
All products that are replaced become the property of SMC. Replacement products may be either new or reconditioned. Any replaced or repaired product carries either a 30-day limited warranty or the remainder of the initial warranty, whichever is longer. SMC is not responsible for any custom software or firmware, configuration information, or memory data of Customer contained in, stored on, or integrated with any products returned to SMC pursuant to any warranty. Products returned to SMC should have any customer-installed accessory or add-on components, such as expansion modules, removed prior to returning the product for replacement. SMC is not responsible for these items if they are returned with the product.
Customers must contact SMC for a Return Material Authorization number prior to returning any product to SMC. Proof of purchase may be required. Any product returned to SMC without a valid Return Material Authorization (RMA) number clearly marked on the outside of the package will be returned to customer at customer’s expense. For warranty claims within North America, please call our toll-free customer support number at (800) 762-4968. Customers are responsible for all shipping charges from their facility to SMC. SMC is responsible for return shipping charges from SMC to customer.
i
LIMITED WARRANTY
WARRANTIES EXCLUSIVE: IF AN SMC PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, CUSTOMER’S SOLE REMEDY SHALL BE REPAIR OR REPLACEMENT OF THE PRODUCT IN QUESTION, AT SMC’S OPTION. THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. SMC NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE OR USE OF ITS PRODUCTS. SMC SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUSTOMER’S OR ANY THIRD PERSON’S MISUSE, NEGLECT, IMPROPER INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR, OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING, OR OTHER HAZARD.
LIMITATION OF LIABILITY: IN NO EVENT, WHETHER BASED IN CONTRACT OR TORT (INCLUDING NEGLIGENCE), SHALL SMC BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE, LOSS OF BUSINESS, OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE, OR INTERRUPTION OF ITS PRODUCTS, EVEN IF SMC OR ITS AUTHORIZED RESELLER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES OR THE LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR CONSUMER PRODUCTS, SO THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, WHICH MAY VARY FROM STATE TO STATE. NOTHING IN THIS WARRANTY SHALL BE TAKEN TO AFFECT YOUR STATUTORY RIGHTS.
* SMC will provide warranty service for one year following discontinuance from the active SMC price list. Under the limited lifetime warranty, internal and external power supplies, fans, and cables are covered by a standard one-year warranty from date of purchase.
SMC Networks, Inc.
20 Mason
Irvine, CA 92618
ii
COMPLIANCES
FCC - Class A
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
You may use unshielded twisted-pair (UTP) for RJ-45 connections - Category 3 or better for 10 Mbps connections, Category 5 or better for 100 Mbps connections, Category 5, 5e, or 6 for 1000 Mbps connections. For fiber optic connections, you may use 50/125 or 62.5/125 micron multimode fiber or 9/125 micron single-mode fiber.
Industry Canada - Class A
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of the Department of Communications.
Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux appareils numériques de Classe A prescrites dans la norme sur le matériel brouilleur: “Appareils Numériques,” NMB-003 édictée par le ministère des Communications.
Japan VCCI Class A
iii
COMPLIANCES
CE Mark Declaration of Conformance for EMI and Safety (EEC)
SMC contact for these products in Europe is:
SMC Networks Europe, Edificio Conata II,
Calle Fructuós Gelabert 6-8, 2o, 4a,
08970 - Sant Joan Despí, Barcelona, Spain.
This information technology equipment complies with the requirements of the Council Directive 89/336/EEC on the Approximation of the laws of the Member States relating to Electromagnetic Compatibility and 73/23/EEC for electrical equipment used within certain voltage limits and the Amendment Directive 93/68/EEC. For the evaluation of the compliance with these Directives, the following standards were applied:
RFI Emission: |
• Limit class A according to EN 55022:1998 |
|
• Limit class A for harmonic current emission according to EN 61000-3-2/ |
|
1995 |
|
• Limitation of voltage fluctuation and flicker in low-voltage supply system |
|
according to EN 61000-3-3/1995 |
Immunity: |
• Product family standard according to EN 55024:1998 |
|
• Electrostatic Discharge according to EN 61000-4-2:1995 |
|
(Contact Discharge: ±4 kV, Air Discharge: ±8 kV) |
|
• Radio-frequency electromagnetic field according to EN 61000-4-3:1996 |
|
(80 - 1000 MHz with 1 kHz AM 80% Modulation: 3 V/m) |
|
• Electrical fast transient/burst according to EN 61000-4-4:1995 (AC/DC |
|
power supply: ±1 kV, Data/Signal lines: ±0.5 kV) |
|
• Surge immunity test according to EN 61000-4-5:1995 |
|
(AC/DC Line to Line: ±1 kV, AC/DC Line to Earth: ±2 kV) |
|
• Immunity to conducted disturbances, Induced by radio-frequency fields: |
|
EN 61000-4-6:1996 (0.15 - 80 MHz with |
|
1 kHz AM 80% Modulation: 3 V/m) |
|
• Power frequency magnetic field immunity test according to |
|
EN 61000-4-8:1993 (1 A/m at frequency 50 Hz) |
|
• Voltage dips, short interruptions and voltage variations immunity test |
|
according to EN 61000-4-11:1994 (>95% Reduction @10 ms, 30% |
|
Reduction @500 ms, >95% Reduction @5000 ms) |
LVD: |
• EN60950-1:2001 |
Warning: Do not plug a phone jack connector in the RJ-45 port. This may damage this device. Attention: Les raccordeurs ne sont pas utilisés pour le système téléphonique!
iv
COMPLIANCES
Safety Compliance
Warning: Fiber Optic Port Safety
|
When using a fiber optic port, never look at the transmit laser while |
CLASS I |
it is powered on. Also, never look directly at the fiber TX port and |
LASER DEVICE |
fiber cable ends when they are powered on. |
|
Avertissment: Ports pour fibres optiques - sécurité sur le plan optique
Ne regardez jamais le laser tant qu’il est sous tension. Ne regardez
DISPOSITIF LASER jamais directement le port TX (Transmission) à fibres optiques et les
DE CLASSE I
embouts de câbles à fibres optiques tant qu’ils sont sous tension.
Warnhinweis: Faseroptikanschlüsse - Optische Sicherheit
Niemals ein Übertragungslaser betrachten, während dieses
LASERGERÄT eingeschaltet ist. Niemals direkt auf den Faser-TX-Anschluß und auf
DER KLASSE I
die Faserkabelenden schauen, während diese eingeschaltet sind.
Power Cord Safety
Please read the following safety information carefully before installing the switch:
WARNING: Installation and removal of the unit must be carried out by qualified personnel only.
•The unit must be connected to an earthed (grounded) outlet to comply with international safety standards.
•Do not connect the unit to an A.C. outlet (power supply) without an earth (ground) connection.
•The appliance coupler (the connector to the unit and not the wall plug) must have a configuration for mating with an EN 60320/IEC 320 appliance inlet.
•The socket outlet must be near to the unit and easily accessible. You can only remove power from the unit by disconnecting the power cord from the outlet.
•This unit operates under SELV (Safety Extra Low Voltage) conditions according to
IEC 60950. The conditions are only maintained if the equipment to which it is connected also operates under SELV conditions.
France and Peru only
This unit cannot be powered from IT† supplies. If your supplies are of IT type, this unit must be powered by 230 V (2P+T) via an isolation transformer ratio 1:1, with the secondary connection point labelled Neutral, connected directly to earth (ground).
† Impédance à la terre
v
COMPLIANCES
Important! Before making connections, make sure you have the correct cord set. Check it (read the label on the cable) against the following:
Power Cord Set
U.S.A. and Canada |
The cord set must be UL-approved and CSA certified. |
|
|
|
The minimum specifications for the flexible cord are: |
|
- No. 18 AWG - not longer than 2 meters, or 16 AWG. |
|
- Type SV or SJ |
|
- 3-conductor |
|
|
|
The cord set must have a rated current capacity of at least 10 A |
|
|
|
The attachment plug must be an earth-grounding type with NEMA |
|
5-15P (15 A, 125 V) or NEMA 6-15P (15 A, 250 V) configuration. |
|
|
Denmark |
The supply plug must comply with Section 107-2-D1, Standard |
|
DK2-1a or DK2-5a. |
|
|
Switzerland |
The supply plug must comply with SEV/ASE 1011. |
|
|
U.K. |
The supply plug must comply with BS1363 (3-pin 13 A) and be fitted |
|
with a 5 A fuse which complies with BS1362. |
|
|
|
The mains cord must be <HAR> or <BASEC> marked and be of |
|
type HO3VVF3GO.75 (minimum). |
|
|
Europe |
The supply plug must comply with CEE7/7 (“SCHUKO”). |
|
|
|
The mains cord must be <HAR> or <BASEC> marked and be of |
|
type HO3VVF3GO.75 (minimum). |
|
|
|
IEC-320 receptacle. |
|
|
Veuillez lire à fond l'information de la sécurité suivante avant d'installer le Switch:
AVERTISSEMENT: L’installation et la dépose de ce groupe doivent être confiés à un personnel qualifié.
•Ne branchez pas votre appareil sur une prise secteur (alimentation électrique) lorsqu'il n'y a pas de connexion de mise à la terre (mise à la masse).
•Vous devez raccorder ce groupe à une sortie mise à la terre (mise à la masse) afin de respecter les normes internationales de sécurité.
•Le coupleur d’appareil (le connecteur du groupe et non pas la prise murale) doit respecter une configuration qui permet un branchement sur une entrée d’appareil EN 60320/IEC 320.
•La prise secteur doit se trouver à proximité de l’appareil et son accès doit être facile. Vous ne pouvez mettre l’appareil hors circuit qu’en débranchant son cordon électrique au niveau de cette prise.
•L’appareil fonctionne à une tension extrêmement basse de sécurité qui est conforme à la norme IEC 60950. Ces conditions ne sont maintenues que si l’équipement auquel il est raccordé fonctionne dans les mêmes conditions.
vi
COMPLIANCES
France et Pérou uniquement:
Ce groupe ne peut pas être alimenté par un dispositif à impédance à la terre. Si vos alimentations sont du type impédance à la terre, ce groupe doit être alimenté par une tension de 230 V (2 P+T) par le biais d’un transformateur d’isolement à rapport 1:1, avec un point secondaire de connexion portant l’appellation Neutre et avec raccordement direct à la terre (masse).
Cordon électrique - Il doit être agréé dans le pays d’utilisation
Etats-Unis et |
Le cordon doit avoir reçu l’homologation des UL et un certificat de la |
Canada: |
CSA. |
|
|
|
Les spécifications minimales pour un cable flexible sont AWG No. 18, |
|
ouAWG No. 16 pour un cable de longueur inférieure à 2 métres. |
|
- type SV ou SJ |
|
- 3 conducteurs |
|
|
|
Le cordon doit être en mesure d’acheminer un courant nominal d’au |
|
moins 10 A. |
|
|
|
La prise femelle de branchement doit être du type à mise à la terre |
|
(mise à la masse) et respecter la configuration NEMA 5-15P (15 A, |
|
125 V) ou NEMA 6-15P (15 A, 250 V). |
|
|
Danemark: |
La prise mâle d’alimentation doit respecter la section 107-2 D1 de la |
|
norme DK2 1a ou DK2 5a. |
|
|
Suisse: |
La prise mâle d’alimentation doit respecter la norme SEV/ASE 1011. |
|
|
Europe |
La prise secteur doit être conforme aux normes CEE 7/7 |
|
(“SCHUKO”) |
|
LE cordon secteur doit porter la mention <HAR> ou <BASEC> et |
|
doit être de type HO3VVF3GO.75 (minimum). |
|
|
Bitte unbedingt vor dem Einbauen des Switches die folgenden Sicherheitsanweisungen durchlesen:
WARNUNG: Die Installation und der Ausbau des Geräts darf nur durch Fachpersonal erfolgen.
•Das Gerät sollte nicht an eine ungeerdete Wechselstromsteckdose angeschlossen werden.
•Das Gerät muß an eine geerdete Steckdose angeschlossen werden, welche die internationalen Sicherheitsnormen erfüllt.
•Der Gerätestecker (der Anschluß an das Gerät, nicht der Wandsteckdosenstecker) muß einen gemäß EN 60320/IEC 320 konfigurierten Geräteeingang haben.
•Die Netzsteckdose muß in der Nähe des Geräts und leicht zugänglich sein. Die Stromversorgung des Geräts kann nur durch Herausziehen des Gerätenetzkabels aus der Netzsteckdose unterbrochen werden.
•Der Betrieb dieses Geräts erfolgt unter den SELV-Bedingungen (Sicherheitskleinstspannung) gemäß IEC 60950. Diese Bedingungen sind nur gegeben, wenn auch die an das Gerät angeschlossenen Geräte unter SELV-Bedingungen betrieben werden.
vii
COMPLIANCES
Stromkabel. Dies muss von dem Land, in dem es benutzt wird geprüft werden:
Schweiz |
Dieser Stromstecker muß die SEV/ASE 1011Bestimmungen |
|
einhalten. |
|
|
Europe |
Das Netzkabel muß vom Typ HO3VVF3GO.75 |
|
(Mindestanforderung) sein und die Aufschrift <HAR> oder |
|
<BASEC> tragen. |
|
Der Netzstecker muß die Norm CEE 7/7 erfüllen (”SCHUKO”). |
|
|
Warnings and Cautionary Messages
Warning: This product does not contain any serviceable user parts.
Warning: Installation and removal of the unit must be carried out by qualified personnel only.
Warning: When connecting this device to a power outlet, connect the field ground lead on the tri-pole power plug to a valid earth ground line to prevent electrical hazards.
Warning: This switch uses lasers to transmit signals over fiber optic cable. The lasers are compliant with the requirements of a Class 1 Laser Product and are inherently eye safe in normal operation. However, you should never look directly at a transmit port when it is powered on.
Caution: Wear an anti-static wrist strap or take other suitable measures to prevent electrostatic discharge when handling this equipment.
Caution: Do not plug a phone jack connector in the RJ-45 port. This may damage this device. Les raccordeurs ne sont pas utilisé pour le système téléphonique!
Caution: Use only twisted-pair cables with RJ-45 connectors that conform to FCC standards.
Warnings (in German)
Achtung: Dieses Produkt enthält keine Teile, die eine Wartung vom Benutzer benötigen.
Achtung: Installation und Deinstallation des Gerätes müssen von qualifiziertem Servicepersonal durchgeführt werden.
Achtung: Wenn das Gerät an eine Steckdose angeschlossen wird, muß der Masseanschluß am dreipoligen Netzstecker mit Schutzerde verbunden werden, um elektrische Gefahren zu vermeiden.
Achtung: Dieses Gerät nutzt Laser zur Signalübertragung über Glasfasern. Die Laser entsprechen den Anforderungen an eine Lasereinrichtung der Klasse 1 und sind durch ihre Bauart im normalen Betrieb sicher für die Augen. Trotzdem sollte niemals direkt in den einen Übertragungskanal geblickt werden, wenn er eingeschaltet ist.
viii
COMPLIANCES
Environmental Statement
The manufacturer of this product endeavours to sustain an environmentally-friendly policy throughout the entire production process. This is achieved though the following means:
•Adherence to national legislation and regulations on environmental production standards.
•Conservation of operational resources.
•Waste reduction and safe disposal of all harmful un-recyclable by-products.
•Recycling of all reusable waste content.
•Design of products to maximize recyclables at the end of the product’s life span.
•Continual monitoring of safety standards.
End of Product Life Span
This product is manufactured in such a way as to allow for the recovery and disposal of all included electrical components once the product has reached the end of its life.
Manufacturing Materials
There are no hazardous nor ozone-depleting materials in this product.
Documentation
All printed documentation for this product uses biodegradable paper that originates from sustained and managed forests. The inks used in the printing process are non-toxic.
Purpose
This guide details the hardware features of the switch, including its physical and performance-related characteristics, and how to install the switch.
Audience
The guide is intended for use by network administrators who are responsible for installing and setting up network equipment; consequently, it assumes a basic working knowledge of LANs (Local Area Networks).
Diese Anleitung ist für die Benutzung durch Netzwerkadministratoren vorgesehen, die für die Installation und das einstellen von Netzwerkkomponenten verantwortlich sind; sie setzt Erfahrung bei der Arbeit mit LANs (Local Area Networks) voraus.
Related Publications
The following publication gives specific information on how to operate and use the management functions of the switch: The SMC6128L2 Management Guide
Also, as part of the switch’s firmware, there is an online web-based help that describes all management related features.
ix
COMPLIANCES
x
TABLE OF CONTENTS
1 |
About the TigerSwitch . . . . . . . . . . . . . . . . . . . . . . . . . |
1-1 |
|
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
1-1 |
|
Switch Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
1-2 |
|
Network Management Options . . . . . . . . . . . . . . . . . . . . . . . . . . |
1-2 |
|
Description of Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
1-2 |
|
10/100BASE-T Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
1-2 |
|
SFP Slots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
1-3 |
|
Port and System Status LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . |
1-3 |
|
Power Supply Socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
1-5 |
|
Features and Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
1-6 |
|
Connectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
1-6 |
|
Expandability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
1-6 |
|
Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
1-6 |
|
Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
1-7 |
2 |
Network Planning . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
2-1 |
|
Introduction to Switching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
2-1 |
|
Application Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
2-2 |
|
Collapsed Backbone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
2-2 |
|
Network Aggregation Plan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
2-3 |
|
Remote Connections with Fiber Cable . . . . . . . . . . . . . . . . . . . . |
2-4 |
|
Making VLAN Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
2-5 |
|
Application Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
2-6 |
3 |
Installing the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . |
3-1 |
|
Selecting a Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
3-1 |
|
Ethernet Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
3-2 |
|
Equipment Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
3-3 |
|
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
3-3 |
|
Optional Rack-Mounting Equipment . . . . . . . . . . . . . . . . . . . . . |
3-3 |
|
Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
3-4 |
|
Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
3-4 |
|
Desktop or Shelf Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
3-6 |
|
Installing an Optional SFP Transceiver . . . . . . . . . . . . . . . . . . . . . . . . . |
3-7 |
xi
TABLE OF CONTENTS
Connecting to a Power Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8 Connecting to the Console Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9 Wiring Map for Serial Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
4 Making Network Connections . . . . . . . . . . . . . . . . . . . 4-1
Connecting Network Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 Twisted-Pair Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 Cabling Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 Connecting to PCs, Servers, Hubs and Switches . . . . . . . . . . . . 4-2 Network Wiring Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 Fiber Optic SFP Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Connectivity Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6 1000BASE-T Cable Requirements . . . . . . . . . . . . . . . . . . . . . . . 4-6 1000 Mbps Gigabit Ethernet Collision Domain . . . . . . . . . . . . . 4-6 100 Mbps Fast Ethernet Collision Domain . . . . . . . . . . . . . . . . 4-7 10 Mbps Ethernet Collision Domain . . . . . . . . . . . . . . . . . . . . . 4-8
Cable Labeling and Connection Records . . . . . . . . . . . . . . . . . . . . . . . . 4-8
A Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-1
Diagnosing Switch Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Power Supply Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
In-Band Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
B Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-1
Twisted-Pair Cable and Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . B-1 10BASE-T/100BASE-TX Pin Assignments . . . . . . . . . . . . . . . . B-2 Straight-Through Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3 Crossover Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3 1000BASE-T Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . B-4 1000BASE-T Cable Requirements . . . . . . . . . . . . . . . . . . . . . . . B-5
Fiber Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-6
C Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-1
Physical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1
Switch Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-2
Management Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-3
xii
TABLE OF CONTENTS
Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-3
Compliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-3
D Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . D-1
E German Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . E-1
Eine Site Auswählen (Selecting a Site) . . . . . . . . . . . . . . . . . . . . . |
. . . . . E-1 |
Montage (Rack Mounting Instructions) . . . . . . . . . . . . . . . . . . . . |
. . . . . E-2 |
Rack-Montage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
. . . . . E-2 |
Anschluss an eine Stromquelle (Connecting to a Power Source) |
. . . . . E-3 |
Glossary
Index
xiii
TABLE OF CONTENTS
xiv
TABLES
Table 1-1 |
Port Status LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
1-4 |
Table 1-2 |
System Status LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
1-5 |
Table 3-1 |
Serial Cable Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
3-9 |
Table 4-1 |
Maximum 1000BASE-T Gigabit Ethernet Cable Length . . |
4-6 |
Table 4-3 |
Maximum 1000BASE-LX Gigabit Ethernet Cable Length |
4-7 |
Table 4-4 |
Maximum 1000BASE-ZX Gigabit Ethernet Cable Length |
4-7 |
Table 4-5 |
Maximum Fast Ethernet Cable Length . . . . . . . . . . . . . . . . |
4-7 |
Table 4-2 |
Maximum 1000BASE-SX Gigabit Ethernet Cable Lengths 4-7 |
|
Table 4-6 |
Maximum Ethernet Cable Length . . . . . . . . . . . . . . . . . . . . |
4-8 |
Table A-1 |
Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
A-1 |
Table B-1 |
10/100BASE-TX MDI and MDI-X Port Pinouts . . . . . . . |
B-2 |
Table B-2 |
1000BASE-T MDI and MDI-X Port Pinouts . . . . . . . . . . . |
B-5 |
Table D-1 |
TigerSwitch 10/100 Products and Accessories . . . . . . . . . . |
D-1 |
xv
xvi
FIGURES
Figure 1-1 Front and Rear Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Figure 1-2 Port LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Figure 1-3 System LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 Figure 1-4 Power Supply Socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 Figure 2-1 Collapsed Backbone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Figure 2-2 Network Aggregation Plan . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Figure 2-3 Remote Connections with Fiber Cable . . . . . . . . . . . . . . 2-4 Figure 2-4 Making VLAN Connections . . . . . . . . . . . . . . . . . . . . . . . 2-5 Figure 3-1 RJ-45 Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 Figure 3-2 Attaching the Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5 Figure 3-3 Installing the Switch in a Rack . . . . . . . . . . . . . . . . . . . . . 3-5 Figure 3-4 Attaching the Adhesive Feet . . . . . . . . . . . . . . . . . . . . . . . 3-6 Figure 3-5 Installing an SFP Transceiver into a Slot . . . . . . . . . . . . . 3-7 Figure 3-6 Power Socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8 Figure 3-7 Serial Port (DB-9 DTE) Pin-Out . . . . . . . . . . . . . . . . . . . 3-9 Figure 4-1 Making Twisted-Pair Connections . . . . . . . . . . . . . . . . . . 4-2 Figure 4-2 Network Wiring Connections . . . . . . . . . . . . . . . . . . . . . . 4-3 Figure 4-3 Making Fiber Port Connections . . . . . . . . . . . . . . . . . . . . 4-5 Figure B-1 RJ-45 Connector Pin Numbers . . . . . . . . . . . . . . . . . . . . B-1 Figure B-2 Straight-through Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . B-3 Figure B-3 Crossover Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4
xvii
FIGURES
xviii
CHAPTER 1
ABOUT THE TIGERSWITCH
Overview
The SMC6128L2 is a Fast Ethernet switch with 24 10/100BASE-TX ports and four Gigabit combination ports1 that are comprised of an RJ-45 port and an SFP transceiver slot. The switch also includes an SNMP-based management agent embedded on the main board. This agent supports both in-band and out-of-band access for managing the switch.
This switch provides a broad range of powerful features for Layer 2 switching, delivering reliability and consistent performance for your network traffic. It brings order to poorly performing networks by segregating them into separate broadcast domains with IEEE 802.1Q compliant VLANs, and empowers multimedia applications with multicast switching and CoS services.
Console Port |
Port Status Indicators |
10/100 Mbps RJ-45 Ports |
System Indicators |
1000BASE-T/SFP Ports |
Power Socket
Figure 1-1 Front and Rear Panels
1. RJ-45 ports shared with a SFP tranceiver slots. If an SFP transceiver is plugged in, the corresponding |
1-1 |
RJ-45 port is disabled. |
ABOUT THE TIGERSWITCH
Switch Architecture
The SMC6128L2 switch employs a wire-speed, non-blocking switching fabric. This permits simultaneous wire-speed transport of multiple packets at low latency on all ports. The switch also features full-duplex capability on all ports, which effectively doubles the bandwidth of each connection.
This switch uses store-and-forward switching to ensure maximum data integrity. With store-and-forward switching, the entire packet must be received into a buffer and checked for validity before being forwarded. This prevents errors from being propagated throughout the network.
Network Management Options
The SMC6128L2 switch contains a comprehensive array of LEDs for “at-a-glance” monitoring of network and port status. It also includes a management agent that allows you to configure or monitor the switch using its embedded management software, or via SNMP applications. To manage the switch, you can make a direct connection to the RS-232 console port (out-of-band), or you can manage the switch through a network connection (in-band) using Telnet, the on-board Web agent, or SNMP-based network management software.
For a detailed description of the advanced features, refer to the Management Guide.
Description of Hardware
10/100BASE-T Ports
The SMC6128L2 contains 24 10/100BASE-TX RJ-45 ports that operate at 10 Mbps or 100 Mbps, half or full duplex. The ports all support automatic MDI/MDI-X operation, so you can use straight-through cables for all network connections to PCs or servers, or to other switches or hubs. (See “10BASE-T/100BASE-TX Pin Assignments” on page B-2.)
1-2
DESCRIPTION OF HARDWARE
Each of these ports support auto-negotiation, so the optimum transmission mode (half or full duplex), and data rate (10 or 100 Mbps) can be selected automatically. If a device connected to one of these ports does not support auto-negotiation, the communication mode of that port can be configured manually.
Each port also supports auto-negotiation of flow control, so the switch can automatically prevent port buffers from becoming saturated.
SFP Slots
The SMC6128L2 contains four Small Form Factor Pluggable (SFP) transceiver slots that are shared with four associated 1000BASE-T RJ-45 ports. If an SFP transceiver (purchased separately) is installed in a slot and has a valid link on the port, the associated RJ-45 port is disabled and cannot be used. The switch can also be configured to force the use of an RJ-45 port or SFP slot, as required.
Port and System Status LEDs
The SMC6128L2 includes a display panel for key system and port indications that simplify installation and network troubleshooting. The LEDs, which are located on the front panel for easy viewing, are shown below and described in the following tables.
|
Port Status LEDs |
Combination Gigabit Port Status LEDs |
||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Figure 1-2 Port LEDs
1-3
ABOUT THE TIGERSWITCH
Table 1-1 Port Status LEDs
LED |
Condition |
Status |
||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
RJ-45 Ports |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Link/ACT |
On/Blinking |
The port has established a valid 100 Mbps link. |
||||||||||||||||
(Link/ |
Green |
Blinking indicates activity. |
||||||||||||||||
Activity) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
On/Blinking |
The port has established a valid 10 Mbps link. |
|||||||||||||||||
|
|
|
|
|||||||||||||||
|
|
|
|
Amber |
Blinking indicates activity. |
|||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Off |
There is no valid link on the port. |
|||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Combination Gigabit Ports |
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Link/ACT |
On/Blinking |
The port has established a valid link. Blinking |
||||||||||||||||
(Link/ |
Green |
indicates activity. |
||||||||||||||||
Activity) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
Off |
There is no valid link on the port. |
|||||||||||||||||
|
|
|
|
|||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1000M |
On Green |
The port is operating at 1000 Mbps. |
||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Off |
When the corresponding Link/ACT LED is on, |
|||||||||||||
|
|
|
|
|
the port is operating at 10 or 100 Mbps. |
|||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
System LEDs |
|||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Figure 1-3 System LEDs
1-4
Loading...