Singer 6184-01, 6184-21 User Manual

0 (0)
Singer 6184-01, 6184-21 User Manual

OPERATOR'S MANUAL

MANUEL de L'UTILISATEUR

MANUAL del OPERADOR

Catalog No. No de Cat.

Número de Catálogo

6184-01

6184-21

HEAVY-DUTY14"HAND-HELDABRASIVECUT-OFFGRINDER ROBUSTE TRONÇONNEUSE MANUELLE À DISQUE ABRASIF 35,6 cm SIERRA TRONZADORA ABRASIVA DE MANO DE 35,6cm

PARA TRABAJOS PESADOS

TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND OPERATOR'S MANUAL.

AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE ET BIEN COMPRENDRE LE MANUEL DE L'UTILISATEUR.

PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER Y ENTENDER EL MANUAL DEL OPERADOR.

GENERAL SAFETY RULES

WARNING!

READ AND UNDERSTAND ALL INSTRUCTIONS.

Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS.

WORK AREA

1.Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.

2.Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.

Power tools create sparks which may ignite the dust or fumes.

3.Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control. Protect others in the work area from debris such as chips and sparks. Provide barriers or shields as needed.

ELECTRICAL SAFETY

4.Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances. Never remove the grounding prong or modify the plug in any way. Do not use any adaptor plugs. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. If the tools should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user.

5.Double Insulated tools are equipped with a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a

qualified electrician to install a polarized outlet. Do not change the plug in any way. Double insulation eliminates the need for the three wire grounded power cord and grounded power supply system.

6.Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded.

7.Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

8.Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately. Damaged cords increase the risk of electric shock.

9.When operating a power tool outside, use an outdoor extension cord marked “W-A” or “W”. These cords are rated for outdoor use and reduce the risk of electric shock.

PERSONAL SAFETY

12.Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with your finger on the switch or plugging in tools with the switch on invites accidents.

13.Remove adjusting keys or wrenches before turning on the tool. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury.

14.Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations.

15.Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions.

TOOL USE AND CARE

16.Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control.

17.Do not force tool. Use the correct tool for your application.

The correct tool will do the job better and safer at the rate for which it is designed.

18.Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled with the switch is dangerous and must be repaired.

19.Disconnect the plug from the power source before making any adjustments, changing accessories, or storing the tool.

Such preventive safety measures reduce the risk of starting the tool accidentally.

20.Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users.

21.Maintain tools with care. Keep cutting tools sharp and clean.

Properly maintained tools with sharp cutting edge are less likely to bind and are easier to control. Do not use a damaged tool. Tag damaged tools “Do not use” until repaired.

22.Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool’s operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools.

23.Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool, may become hazardous when used on another tool.

SERVICE

10. Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.

11.Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts.

24.Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury.

25.When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of electric shock or injury.

page 2

SPECIFIC SAFETY INSTRUCTIONS - HAND-HELD ABRASIVE CUT-OFF GRINDER

1.To reduce the risk of injury, avoid inhalation of dust generated by grinding and cutting operations. Exposure to dust may cause respiratory ailments. Use approved NIOSH or OSHA respirators, safety glasses or face shields, gloves and protective clothing. Provide adequate ventilation to eliminate dust, or to maintain dust level below the Threshold Limit Value for nuisance dust as classified by OSHA.

2.Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a “live” wire will make exposed metal parts of tool “live” and shock the operator.

3.Maintain labels and nameplates. These carry important information. If unreadable or missing, contact a MILWAUKEE service facility for a free replacement.

4.WARNING! Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

lead from lead-based paint

crystalline silica from bricks and cement and other masonry products, and

arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specifically designed to filter out microscopic particles.

Wheel Instructions

5.Use only the edge (not the sides) of the wheel for cutting. Do not allow the wheel to twist or bind.

6.Keep hands and body away from the rotating wheel. Do not wear loose clothing when using this tool.

7.Store cut-off wheels with care. Do not drop them or subject them to excessive heat, cold or humidity.

8.Make sure that all wheel flanges and other mounting hardware are in good condition and are always used properly. Defective or missing parts may cause damage to the wheel. Always use mounting flanges supplied with the tool.

9.Cutting with a damaged wheel is very hazardous. After installing a new wheel, leave the tool unplugged and rotate the wheel by hand to see if it is uneven, warped, or cracked. If so, discard the wheel and replace it with a new one. Do not use a wheel that has been dropped; impact may result in breakage.

10.Before starting a cut, step back from the tool and make a trial run to confirm that the wheel is in good condition. Trial run periods are: When replacing a cut-off wheel — over 3 minutes.

When starting routine work — over 1 minute.

11.Before installing a cut-off wheel, always inspect it for cracks. Visually check resinoid and rubber-bonded wheels for cracks. Replace cracked wheel immediately.

12.Always check maximum operating speed established for wheel against grinder speed. Do not exceed the maximum operating speed that is marked on the wheel.

13.Do not force a wheel onto the grinder or alter the size of the arbor hole. Don't use a wheel that fits the arbor too loosely. If the wheel doesn't fit the grinder, get one that does.

14.Do not set the depth of cut to more than 1/2". Make successive passes to achieve a greater depth of cut. Cutting at a depth of more than 1/2" will damage the wheel.

15.Do not attempt to install saw blades on this tool because it is not designed for this type of blade.

16.Do not overtighten wheel nut.

17.Start cutting only after the motor has reached full speed.

18.Release switch immediately if the cut-off wheel stops rotating or if the motor sounds like it is straining.

19.Keep flammable and fragile objects away from this tool. Do not allow cut-off sparks to contact the operator's hands, face or feet.

20.Place the tool securely on a flat, level surface.

21.Always use the tool with the proper voltage specified on the tool's nameplate.

22.Never touch a short cut-off piece until it cools.

23.Never attempt to cut material larger than the rated capacity listed in “Specifications”.

24.Never stand in line with the wheel while cutting. Always stand to the side.

25.Always keep guards in place.

26.Always start the cut gently. Do not bump or bang a wheel to start a cut.

page 3

Symbology

 

Specifications

 

 

 

Double Insulated

Volts Alternating Current

Amps

No Load Revolutions per Minute (RPM)

Underwriters Laboratories, Inc.

Canadian Standards Association

Cut-Off Grinder Capacities

 

Cat.

 

Wheel

 

RPM

 

Volts

 

 

 

 

Cutting

Arbor Hole

 

No.

 

Size

 

 

AC

 

Amps

Capacity

Size

6184-01

 

14"

 

4350

 

120

 

18

 

4-7/16"

 

1" or 20 mm

 

 

 

 

 

 

 

 

 

 

 

Abrasive Cut-Off Wheel Capacities

 

 

Cat.

Wheel

 

Max. rated RPM

 

Wheel

 

Arbor Hole

 

 

No.

Size

 

 

(at least)

 

Thickness

 

Size

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6184-01

14"

 

 

 

5000

 

 

 

1/8"

 

1" or 20 mm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FUNCTIONALDESCRIPTION

1.

Trigger

2

2.

Guard

 

3.

Shoe assembly

1

 

 

4.Abrasive cut-off wheel

5.Side handle

4

3

5

page 4

GROUNDING

WARNING!

Improperly connecting the grounding wire can result in the risk of electric shock. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the tool. Never remove the grounding prong from the plug. Do not use the tool if the cord or plug is damaged. If

damaged, have it repaired by a MILWAUKEE service facility before use. If the plug will not fit

the outlet, have a proper outlet installed by a qualified electrician.

MILWAUKEE Heavy-Duty 14" Hand-Held Abrasive Cut-Off Grinders are provided with a 20 amp locking plug (NEMA L5-20) (Fig. A).

Fig. A

Grounding

 

Cover of grounded

Grounded Tools:

Tools with Three Prong Plugs

Tools marked “Grounding Required” have a three wire cord and three prong grounding plug. The plug must be connected to a properly grounded outlet (Fig. A). If the tool should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user, reducing the risk of electric shock.

The grounding prong in the plug is connected through the green wire inside the cord to the grounding system in the tool. The green wire in the cord must be the only wire connected to the tool's grounding system and must never be attached to an electrically “live” terminal.

Your tool must be plugged into an appropriate outlet, properly installed and grounded in accordance with all codes and ordinances. The plug and outlet should look like those in Figure A.

Double Insulated Tools:

Tools with Two Prong Plugs

Tools marked “Double Insulated”

 

 

not require grounding. They have

 

 

special double insulation system

 

 

which satisfies OSHA requirements

 

 

and complies with the applicable

 

 

standards of Underwriters Labora

 

 

tories, Inc., the Canadian Standard

 

 

Association and the National Electri

 

 

cal Code. Double Insulated tools may

 

 

be used in either of the 120 volt out-

Fig. B

Fig. C

lets shown in Figures B and C.

EXTENSIONCORDS

Grounded tools require a three wire extension cord. Double insulated tools can use either a two or three wire extension cord. As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop in voltage, resulting in loss of power and possible tool damage. Refer to the table shown to determine the required minimum wire size.

The smaller the gauge number of the wire, the greater the capacity of the cord. For example, a 14 gauge cord can carry a higher current than a 16 gauge cord. When using more than one extension cord to make up the total length, be sure each cord contains at least the minimum wire size required. If you are using one extension cord for more than one tool, add the nameplate amperes and use the sum to determine the required minimum wire size.

Guidelines for Using Extension Cords

If you are using an extension cord outdoors, be sure it is marked with the suffix “W-A” (“W” in Canada) to indicate that it is acceptable for outdoor use.

Be sure your extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified person before using it.

Protect your extension cords from sharp objects, excessive heat and damp or wet areas.

Recommended Minimum Wire Gauge

for Extension Cords*

Nameplate

 

Extension Cord Length

 

 

 

 

 

 

Amperes

25'

50'

75'

100'

150'

200'

 

 

 

 

 

 

 

0 - 5

16

16

16

14

12

12

5.1

- 8

16

16

14

12

10

--

8.1 - 12

14

14

12

10

--

--

12.1

- 15

12

12

10

10

--

--

15.1

- 20

10

10

10

--

--

--

 

 

 

 

 

 

 

 

* Based on limiting the line voltage drop to five volts at 150% of the rated amperes.

READ AND SAVE ALL INSTRUCTIONS FOR

FUTURE USE.

page 5

TOOL ASSEMBLY

WARNING!

To reduce the risk of injury, always unplug tool before attaching or removing accessories or making adjustments. Use only specifically recommended accessories. Others may be hazardous.

Installing Guard (Fig. 1)

Fig. 1

Guard

Spindle

Hex bolt

1.Place the tool on a firm surface with the spindle hub facing up.

2.Loosen the hex bolt on the guard with the allen wrench provided with the tool.

3.Slide the guard over the spindle hub and tighten the hex bolt with the allen wrench.

To change wheels:

1.To install cut-off wheels, place tool on a firm surface with the guard surface facing up.

2.Slide the back flange, cut-off wheel, top flange and nut over the spindle.

3.Tighten nut securely with the wrench provided with tool.

NOTE: Nut has a left hand thread. To tighten, turn nut in a counterclockwise rotation.

4.To remove cut-off wheels, loosen and remove nut, top flange and cut-off wheel from spindle by securing back flange with wrench and loosen nut with a second wrench.

Installing and Removing Shoe (Fig. 3)

Fig. 3

Wing nuts

WARNING!

To reduce the risk of injury, use only the proper wheel made for this tool. DO NOT USE ANY TYPE OF SAW BLADE. USE ONLY TYPE “1” ABRASIVE AND DIAMOND WHEELS.

Removing and Installing Cut-Off Wheels (Fig. 2)

Before operating the tool, make sure the wheel is in good condition as described (see “Special Safety Instructions - Hand-Held Abrasive CutOff Grinder”).

Fig. 2

Nut

 

 

Top flange

1.To install shoe assembly, loosen wing nuts on shoe assembly.

2.Place the first bolt head into the hole on the guard. Angle shoe assembly as shown, to place the second bolt.

3.Adjust shoe to proper height and tighten wing nuts securely.

4.To remove shoe assembly, loosen wing nuts and slide shoe assembly so that both bolts can be removed from holes in guard.

Installing Side Handle

1.To install handle, place tool on guard side.

2.Align bolts with threaded holes in gear case and tighten securely.

Cutting wheel

Back flange

Spindle

page 6

OPERATION

WARNING!

To reduce the risk of injury, wear safety goggles or glasses with side shields. Unplug the tool before changing accessories or making adjustments.

Adjusting the Depth of Cut (Fig. 4)

The shoe assembly can be moved to change the depth of cut. Cut-off wheels wear down as they are used and the depth of cut may need to

be adjusted.

Wing nut

Fig. 4

Wing nut

Shoe assembly

Lower shoe assembly for shallower cuts.

Raise shoe assembly for deeper cuts.

1.Unplug tool.

2.To change the depth of cut, loosen the wing nuts on shoe assembly (counterclockwise).

3.Position the depth of the shoe assembly for deeper or shallower depth (Fig. 4).

NOTE: Make repeated passes at depths of less than 1/2" to achieve the desired depth. Cutting at a depth of more than 1/2" will damage the wheel.

4.Tighten the wing nuts securely (clockwise).

NOTE: The MILWAUKEE Hand-Held Abrasive Cut-Off Grinder is designed to cut metal and non-metallic materials. It is NOT recommended for cutting wood. DO NOT attempt to install a saw blade on the tool. DO NOT use with liquids or in damp locations.

Starting and Stopping the Tool

The tool operates at no load speed of 4350 RPM.

1.Plug in tool.

2.To start the tool, pull the trigger.

3.To stop the tool, release the trigger.

Preventing Kickback

Kickback is the sudden reaction to a pinched wheel which could cause a cut-off grinder that is not under control to lift up and out of the workpiece towards the user. Take the precautions below to help prevent kickback.

1.Maintain a firm grip and correct body position. Position arms and body to control the backward and upward reaction force of kickback. Control the cut-off grinder at all times.

2.Set the depth of cut for no more than necessary. The less wheel exposed, the less chance of binding and kickback. Before cutting, be sure shoe assembly is tight.

3.Always allow the blade to come to a full stop before removing the cut-off grinder from the workpiece. Never remove the cut-off grinder from a cut while the blade is moving. If restarting or correcting direction in mid-cut, allow the blade to coast to a stop, back the cut-off grinder up a few inches and center it in the kerf before restarting.

4.Stay alert. Any distraction can cause twisting or binding. Repetitive cuts may lull the user into careless movements.

5.Do not force the tool. Forcing a cut-off grinder reduces control and cutting efficiency.

If kickback should occur, continue to grip the cut-off grinder firmly and immediately release trigger.

WARNING!

Only use abrasive and diamond cutting wheels with a maximum safe operating speed greater than the RPM marked on the tool's nameplate.

Wheel Selection

Non-metallic Materials

When cutting non-metallic materials, use a silicone carbide abrasive cutoff wheel of at least 1/8" thickness which is rated with a maximum safe operating speed at least 5000 RPM. READ SAFETY INFORMATION SUPPLIED WITH CUT-OFF WHEEL. Always wear a dust mask.

Metallic Materials

When cutting metals, use an aluminum oxide abrasive cut-off wheel of at least 1/8" thickness which is rated with a maximum safe operating speed at least 5000 RPM. READ SAFETY INFORMATION SUPPLIED WITH CUTOFF WHEEL. Protect everyone in the area from sparks.

Masonry Materials

When cutting masonry materials, use dry diamond wheels or silicone carbide abrasive cut-off wheel of at least 1/8" thickness which is rated with a maximum safe operating speed at least 5000 RPM. READ SAFETY INFORMATION SUPPLIED WITH CUT-OFF WHEEL. Always wear a dust mask.

Making a Cut

1.Unplug tool. Select a cutting depth and adjust the height of the shoe assembly as described in “Adjusting the Depth of Cut”.

2.Plug the tool in and pull the trigger. Allow the motor to reach full speed and then slowly lower the wheel into the workpiece.

NOTE: Always start the cut gently; do not bang or bump a wheel when starting the cut.

3.While cutting, keep the shoe flat against the workpiece and maintain a firm grip. Do not force the cut-off grinder through the work. Forcing a cut-off grinder can cause kickback.

Make repeated passes at depths of less than 1/2" to achieve the desired depth. Cutting at a depth of more than 1/2" will damage the wheel. Frequently clean dust from air vents and guards.

4.When the cut is finished, always allow the motor to come to a complete stop. Never remove the cut-off grinder from a cut while the blade is moving.

5.If making a partial cut, restarting a cut or correcting cut direction, allow the wheel to come to a complete stop. To resume cutting, center the wheel in the kerf (cutting slot), back the saw away from cutting edge a few inches, pull the trigger and re-enter the cut slowly.

NOTE: If the cut-off grinder stalls, maintain a firm grip and release the trigger immediately. Correct the problem before continuing.

page 7

MAINTENANCE

WARNING!

To reduce the risk of injury, always unplug your tool before performing any maintenance. Never disassemble the tool or try to do any rewiring on the tool's electrical system. Contact a MILWAUKEE service facility for ALL repairs.

Maintaining Tools

Keep your tool in good repair by adopting a regular maintenance program. Before use, examine the general condition of your tool. Inspect guards, switches, tool cord set and extension cord for damage. Check for loose screws, misalignment, binding of moving parts, improper mounting, broken parts and any other condition that may affect its safe operation. If abnormal noise or vibration occurs, turn the tool off immediately and have the problem corrected before further use. Do not use a damaged tool. Tag damaged tools “DO NOT USE” until repaired (see “Repairs”).

Under normal conditions, relubrication is not necessary until the motor brushes need to be replaced. After six months to one year, depending on use, return your tool to the nearest MILWAUKEE service facility for the following:

Lubrication

Brush inspection and replacement

Mechanical inspection and cleaning (gears, spindles, bearings, housing, etc.)

Electrical inspection (switch, cord, armature, etc.)

Testing to assure proper mechanical and electrical operation

WARNING!

To reduce the risk of injury, electric shock and damage to the tool, never immerse your tool in liquid or allow a liquid to flow inside the tool.

Cleaning

Clean dust and debris from vents. Keep the tool handles clean, dry and free of oil or grease. Use only mild soap and a damp cloth to clean your tool since certain cleaning agents and solvents are harmful to plastics and other insulated parts. Some of these include: gasoline, turpentine, lacquer thinner, paint thinner, chlorinated cleaning solvents, ammonia and household detergents containing ammonia. Never use flammable or combustible solvents around tools.

Repairs

If your tool is damaged, return the entire tool to the nearest service center listed on the back cover of this operator’s manual.

page 8

ACCESSORIES

WARNING!

To reduce the risk of injury, always unplug the tool before attaching or removing accessories. Use only specifically recommended accessories. Others may be hazardous.

For a complete listing of accessories refer to your MILWAUKEE Electric Tool catalog. To obtain a catalog, contact your local distributor or a service center listed on the back cover of this operator’s manual.

14" Abrasive Cut-Off Wheels

Cat. No. 49-93-6105

Cat. No. 49-93-6106

Cat. No. 49-93-6107

Cat. No. 49-93-6108

12" Abrasive Cut-Off Wheels

Cat. No. 49-93-6101

Cat. No. 49-93-6102

Cat. No. 49-93-6103

Cat. No. 49-93-6104

12" Dry Cutting Diamond Blade

Cat. No. 49-93-8030

 

Wheel Guard

Shoe

Cat. No. 43-54-0775

Cat. No. 43-40-0315

Top Flange

Back Flange

Cat. No. 43-34-0780

Cat. No. 43-34-0785

Flange Nut 20mm

Flange Nut 1"

Cat. No. 44-40-0605

Cat. No. 44-40-0705

Hex Wrench

Open End Wrench

Cat. No. 49-96-0225

Cat. No. 49-96-4121

WARRANTY

Every MILWAUKEE product is warranted to be free from defects in material and workmanship. MILWAUKEE will repair or replace any product which examination proves to be defective in material or workmanship.

Limitations: This warranty does not cover: 1) repairs made or attempted by other than MILWAUKEE or MILWAUKEE Authorized Service Station personnel; 2) normal wear and tear; 3) abuse; 4) misuse; 5) improper maintenance; 6) continued use after partial failure; 7) tools that have been modified; or product used with an improper accessory.

Battery Packs are warranted for one (1) year from the date of purchase.

Should a problem develop, return the complete product to any MILWAUKEE Factory Service Center or MILWAUKEE Authorized Service Station, freight prepaid and insured. If inspection shows the problem is caused by a defect in material or workmanship, all repairs or a replacement will be made at no charge and the product will be returned, transportation prepaid. No other warranty, written or verbal, is authorized.

THE REPAIR AND REPLACEMENT REMEDIES DESCRIBED HEREIN ARE EXCLUSIVE. IN NO EVENT SHALL MILWAUKEE BE LIABLE FOR ANY INCIDENTAL, SPECIAL, OR CONSEQUENTIAL DAMAGES, INCLUDING LOSS OF PROFITS.

THISWARRANTYISINLIEUOFALLOTHERWARRANTIES, EXPRESSED OR IMPLIEDWHETHERFORMERCHANTABILITYORFITNESSFORPARTICULAR USEORPURPOSE.

This warranty gives you specific legal rights. You may also have other rights that vary from state to state. In those states that do not allow the exclusion of implied warranties or limitations of incidental or consequential damages, the above limitations or exclusions may not apply to you.

Loading...
+ 16 hidden pages