Siemens 5935, 5930 User Manual

0 (0)

SIEMENS Business Class

5930/5935

Business Gateway

User’s Guide

Part No. 107-5930-000

Software License and Limited Warranty

© Copyright 2004, Siemens Subscriber Networks, Inc. All rights reserved. Printed in the U.S.A.

Siemens Subscriber Networks, Efficient Networks, the Efficient Networks logo, and SpeedStream(tm) are trademarks of Siemens AG. All other names may be trademarks, service marks or registered trademarks held by their respective companies. This document is for information purposes only,Siemens Subscriber Networks is not responsible for errors or omissions herein. Siemens Subscriber Networks reserves the right to make changes to product specifications without notice.

SIemens Subscriber Networks, Inc. – End User Software License and Warranty

INSTALLATION OF THE HARDWARE AND SOFTWARE PROVIDED BY SIEMENS SUBSCRIBER NETWORKS, INC (SSN). CONSTITUTES ACCEPTANCE BY YOU OF THE TERMS OF THE FOLLOWING SOFTWARE LICENSE AND LIMITED WARRENTY. IF YOU DO NOT ACCEPT THESE TERMS, PLEASE RETURN THE HARDWARE AND SOFTWARE AND SOFTWARE IN ITS ORIGINAL PACKAGING TO THE VENDOR FROM WHICH YOU PURCHASED IT FOR A FULL REFUND OF THE PURCHASE PRICE.

The following describes your license to use the software (the"Software") that has been provided with your Siemens customer premise equipment ("Hardware") and the limited warranty that Siemens Subscriber Networks provides on its Software and Hardware. Siemens Subscriber Networks reserves any right not expressly granted to the end user.

Software License

The Software is protected by copyright laws and international copyright treaties. The Software is licensed and not sold to you. The definition od Software includes, but not limited to, system and operating software marketed by Siemens Subscriber Networks, including firmware, embedded software, software provided on media, downloadable software, software for configuration or programmable logic elements, and all Siemens Subscriber Networks maintenance and diagnostic tools associated with the above mentioned software. Accordingly, while you own the media (such as CD ROM or floppy disk) on which the software is recorded, Siemens Subscriber Networks or its licensors retains ownership of the Software itself.

1.Grant of License. You may install and use one (and only one) copy of the Software in conjunction with the Siemens Subscriber Networks provided Hardware. You may make backup copies of the system configuration as required. If the Hardware is being installed on a network, you may install the Software on the network server or other server-side devise on which the Hardware is being installed and onto the client-side devices.

2.Restrictions. The license granted is a limited license. You may NOT:

sublicense, assign, or distribute copies of the Software to others;

decompile, reverse engineer, disassemble or otherwise reduce the Software or any part thereof to a human perceivable form;

modify, adapt, translate or create derivative works based upon the Software or any part thereof; or

rent, lease, loan or otherwise operate for profit the Software.

2.Transfer. You may transfer the Software only where you are also transferring the Hardware. In such cases, you must remove all copies of the Software from any devices onto which you have installed it, and must ensure that the party to whom you transfer the Hardware receives this License Agreement and Limited Warranty.

3.Upgrades Covered. This License covers the Software originally provided to you with the Hardware, and any additional software that you may receive from Siemens Subscriber Networks, whether delivered via tangible media (CD ROM or floppy disk), down loaded from Siemens Subscriber Networks, or delivered through customer support. Any such additional software shall be considered "Software" for all purposes under this License.

4.Export Law Assurances. You acknowledge that the Software may be subject to export control laws and regulations of the U.S.A. You confirm that you will not export or re-export the Software to any countries that are subject to export restrictions.

5.No Other Rights Granted. Other than the limited license expressly granted herein, no license, whether express or implied, by estoppel or otherwise, is granted to any copyright, patent, trademark, trade secret, or other proprietary rights of Siemens Subscriber Networks or its licensors.

6.Termination. Without limiting Siemens Subscriber Networks’s other rights, Siemens Subscriber Networks may terminate this license if you fail to comply with any of these provisions. Upon termination, you must return the Software and all copies thereof.

Limited Warranty

The following limited warranties provided by Siemens Subscriber Networks extend to the original end user of the Hardware/licensee of the Software and are not assignable or transferable to any subsequent purchaser/licensee.

1.Hardware. Siemens Subscriber Networks warrants that the Hardware will be free from defects in materials and workmanship and will perform substantially in compliance with the user documentation relating to the Hardware for a period of one year from the date the original end user received the Hardware.

2.Software. Siemens Subscriber Networks warrants that the Software will perform substantially in compliance with the end user documentation provided with the Hardware and Software for a period of ninety days from the date the original end user received the Hardware and Software. The end user is responsible for the selection of Hardware and Software used in the end user’s network. Given the wide range of third-party hardware and applications, Siemens Subscriber Networks does not warrant the compatibility or uninterrupted or error free operation of our Software with the end user’s systems or network.

3.Exclusive Remedy. Your exclusive remedy and Siemens Subscriber Networks’s exclusive obligation for breach of this limited warranty is, in Siemens Subscriber Networks’s sole option, either (a) a refund of the purchase price paid for the Hardware/Software or (b) repair or replacement of the Hardware/Software with new or remanufactured products. Any replacement Hardware or Software will be warranted for the remainder of the original warranty period or thirty days, which ever is longer.

4.Warranty Procedures. If a problem develops during the limited warranty period, the end user shall follow the procedure outlined below:

A.Prior to returning a product under this warranty, the end user must first call Siemens Subscriber Networks at (888) 286-9375, or send an email to Siemens Subscriber Networks at support@efficient.com to obtain a return materials authorization (RMA) number. RMAs are issued between 8:00 a.m. and 5:00 p.m. Central Time, excluding weekends and holidays. The end user must provide the serial number(s) of the products in order to obtain an RMA.

B.After receiving an RMA, the end user shall ship the product or defective component, including power supplies and cable, where applicable, freight or postage prepaid and insured, to Siemens Subscriber Networks at 4849 Alpha Road, Dallas Texas 75244, U.S.A. Within five (5) days notice from Siemens Subscriber Networks, the end user shall provide Siemens Subscriber Networks with any missing items or, at Siemens Subscriber Networks’s sole option, Siemens Subscriber Networks will either (a) replace missing items and charge the end user or (b) return the product to the end user freight collect. The end user shall include a return address, daytime phone number and/or fax. The RMA number must be clearly marked on the outside of the package.

C.Returned Products will be tested upon receipt by Siemens Subscriber Networks. Products that pass all functional tests will be returned to the end user.

D.Siemens Subscriber Networks will return the repaired or replacement Product to the end user at the address provided by the end user atSiemens Subscriber Networks’s expense. For Products shipped within the United States of America, Siemens Subscriber Networks will use reasonable efforts to ensure delivery within five (5) business days from the date received by Siemens Subscriber Networks. Expedited service is available at additional cost to the end user.

E.Upon request from Siemens Subscriber Networks, the end user must prove the date of the original purchase of the product by a dated bill of sale or dated itemized receipt.

5.Limitations.

The end user shall have no coverage or benefits under this limited warranty if the product has been subject to abnormal use, abnormal conditions, improper storage, exposure to moisture or dampness, unauthorized modifications, unauthorized repair, misuse, neglect, abuse, accident, alteration, improper installation, or other acts which are not the fault of Siemens Subscriber Networks, including acts of nature and damage caused by shipping.

Siemens Subscriber Networks will not honor, and will not consider the warranty voided, if: (1) the seal or serial number on the Product have been tampered with or (2) there has been any attempted or actual repair or modification of the Product by anyone other than an Siemens Subscriber Networks authorized service provider.

The limited warranty does not cover defects in appearance, cosmetic, decorative or structural items, including framing, and any non-operative parts.

Siemens Subscriber Networks’s limit of liability under the limited warranty shall be the actual cash value of the product at the time the end user returns the product for repair, determined by the price paid by the end user for the product less a reasonable amount for usage.Siemens Subscriber Networks shall not be liable for any other losses or damages.

The end user will be billed for any parts or labor charges not covered by this limited warranty. The end user will be responsible for any expenses related to reinstallation of the product.

THIS LIMITED WARRENTY IS THE ONLY WARRENTY SSN MAKES FOR THE PRODUCT AND SOFTWARE. TO THE EXTENT ALLOWED BY LAW, NO OTHER WARRENTY APPLIES, WETHER EXPRESS, IMPLIED OR STATUTORY, INCLUDING ANY WARRENTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

6.Out of Warranty Repair. Out of warranty repair is available for a fixed fee. Please contact Siemens Subscriber Networks at the numbers provided above to determine out of warranty repair rate. End users seeking out of warranty repair should contact Siemens Subscriber Networks as described above to obtain an RMA and to arrange for payment of the repair charge. All shipping charges will be billed to the end-user.

General Provisions

The following general provisions apply to the foregoing Software License and Limited Warranty.

1.No Modification. The foregoing Limited Warranty is the end user’s sole and exclusive remedy and is in lieu of all other warranties, express or implied. No oral or written information or advice given by Siemens Subscriber Networks or tis dealers, distributors, employees or agents shall in any way extend, modify or add to the foregoing Software License and Limited Warranty. This Software License and Limited Warranty constitutes the entire agreement between Siemens Subscriber Networks and the end user, and supersedes all prior and contemporaneous representation, agreements or understandings, oral or written. This Software License and Limited Warranty may not be changed or amended except by a written instrument executed by a duly authorized officer of Siemens Subscriber Networks.

Siemens Subscriber Networks neither assumes nor authorizes any authorized service center or any other person or entity to assume for it any other obligation or liability beyond that which is expressly provided for in this Limited Warranty including the provider or seller of any extended warranty or service agreement.

The Limited Warranty period for Siemens Subscriber Networks supplied attachments and accessories is specifically defined within their own warranty cards and packaging.

2.EXCLUSION OF INCIDENTAL, CONSEQUENTIAL AND OTHER DAMAGES. TO THE FULL EXTENT PERMITTED BY LAW, IN NO EVENT SHALL SSN OR ITS LICENSORS BE LIABLE, WHETHER UNDER CONTRACT, WARRENTY, TORT OR ANY OTHER THEORY OF LAW FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRPUTION, PERSONAL INJURY, LOSS OR IMPAIRMENT OF DATA OR BUSINESS INFORMATION, EVEN IF SSN HAS BEEN NOTIFIED OF THE POSSIBILITY OF SUCH DAMAGES. SSN’S OR IT’S LICENSOR’S LIABILITY TO YOU (IF ANY) FOR ACTUAL DIRECT DAMAGES FOR ANY CAUSE WHATSOEVER, AND REGARDLESS OF THE FORM OF THE ACTION, WILL BE LIMITED TO, AND SHALL NOT EXCEED, THE AMOUNT PAID FOR THE HARDWARE/ SOFTWARE.

3.General. This Software License and Limited Warranty will be covered by and construed in accordance with the laws of the State of Texas, United States (excluding conflicts of laws rules), and shall insure to the benefit of Siemens Subscriber Networks and its successor, assignees and legal representatives. If any provision of this Software License and Limited Warranty is held by a court of competent jurisdiction to be a invalid or unenforceable to any extent under applicable law, that provision will be enforced to the maximum extent permissible, and the remaining provisions of this Software License and Limited Warranty will remain in full force and effect. Any notices or other communications to be sent to Siemens Subscriber Networks must be mailed by certified mail to the following address:

Siemens Subscriber Networks, Inc. 4849 Alpha Road

Dallas, TX 75244 U.S.A.

Attn: Customer Service

SIEMENS 5930/5935 Business Gateway

User’s Guide

Table of Contents

Chapter 1 Product Specifications

 

Front Panel for 5930 ....................................................................................................................................

1

Back Panel for 5930.....................................................................................................................................

1

Hardware Specifications for 5930 ................................................................................................................

2

Physical Specifications....................................................................................................................

2

Operational Environment ................................................................................................................

2

Power Requirements.......................................................................................................................

2

Processor ........................................................................................................................................

2

LAN Interface ..................................................................................................................................

2

WAN Interface.................................................................................................................................

2

Serial Interface ................................................................................................................................

2

Agency Approvals ...........................................................................................................................

2

Software Specifications for 5930..................................................................................................................

3

Bridging ...........................................................................................................................................

3

Configuration Management.............................................................................................................

3

Dial Backup .....................................................................................................................................

3

Routing............................................................................................................................................

3

Differentiated Services - Quality of Service provisioning ................................................................

3

Asynchronous Transfer Mode (ATM) ..............................................................................................

3

IP Address Translation....................................................................................................................

3

Protocol Conformance Testing ........................................................................................................

3

PPP (RFC 1661) .............................................................................................................................

4

Security ...........................................................................................................................................

4

Front Panel for 5935 ....................................................................................................................................

5

Back Panel for 5935.....................................................................................................................................

5

Hardware Specifications for 5935 ................................................................................................................

6

Physical Specifications....................................................................................................................

6

Operational Environment ................................................................................................................

6

Power Requirements.......................................................................................................................

6

Processor ........................................................................................................................................

6

LAN Interface ..................................................................................................................................

6

WAN Interface.................................................................................................................................

6

Serial Interface ................................................................................................................................

6

Agency Approvals ...........................................................................................................................

6

Software Specifications for 5935..................................................................................................................

7

Bridging ...........................................................................................................................................

7

Configuration Management.............................................................................................................

7

Routing............................................................................................................................................

7

Differentiated Services - Quality of Service provisioning ................................................................

7

Dial Backup .....................................................................................................................................

7

Asynchronous Transfer Mode (ATM) ..............................................................................................

7

IP Address Translation....................................................................................................................

8

Protocol Conformance Testing ........................................................................................................

8

PPP (RFC 1661) .............................................................................................................................

8

SIEMENS

i

SIEMENS 5930/5935 Business Gateway

 

User’s Guide

 

Security ...........................................................................................................................................

8

Chapter 2 Installation

 

Installation Requirements.............................................................................................................................

9

Package Contents...........................................................................................................................

9

PC Requirements............................................................................................................................

9

Network Service Provider Requirements ......................................................................................

10

Hardware Installation ..................................................................................................................................

11

PC Configuration........................................................................................................................................

12

Windows 98/ME ............................................................................................................................

12

Windows NT 4...............................................................................................................................

13

Windows 2000...............................................................................................................................

14

Windows XP..................................................................................................................................

15

Mac OS 9.x ...................................................................................................................................

16

Mac OSX.......................................................................................................................................

17

Linux..............................................................................................................................................

18

Configuring the Router ...............................................................................................................................

19

Establish Connection ....................................................................................................................

19

Router Information Page ...............................................................................................................

20

Chapter 3 Easy Setup

 

Access Easy Setup Wizard........................................................................................................................

21

Select Protocol...........................................................................................................................................

21

Point-to-Point Protocol over ATM..................................................................................................

22

Point-to-Point Protocol over Ethernet over PPPoA .......................................................................

23

Point-to-Point Protocol over Ethernet over RFC1483 ...................................................................

24

RFC 1483......................................................................................................................................

25

RFC 1483 MAC Encapsulated Routing (MER) .............................................................................

26

Dynamic Host Configuration Protocol ...........................................................................................

27

Local Area Network Configuration ................................................................................................

28

Chapter 4 User Setup

 

User Management......................................................................................................................................

29

Adding/Modifying A User Account.................................................................................................

30

Deleting A User Account ...............................................................................................................

31

User Lookup..................................................................................................................................

32

Secure Mode Configuration ..........................................................................................................

33

Configure the Radius Server.........................................................................................................

34

Configure the TacPlus Server .......................................................................................................

35

Management Classes ...................................................................................................................

36

Change Password......................................................................................................................................

37

Access Control...........................................................................................................................................

38

Chapter 5 Advanced Setup

 

Router Clock ..............................................................................................................................................

40

DHCP.........................................................................................................................................................

41

QoS............................................................................................................................................................

42

SIEMENS

ii

SIEMENS 5930/5935 Business Gateway

 

User’s Guide

 

Configure QoS Policy....................................................................................................................

43

Reorder QoS Policies....................................................................................................................

45

Routing Table Configuration.......................................................................................................................

46

Dial Backup................................................................................................................................................

47

Internal Modem .............................................................................................................................

48

External Modem ............................................................................................................................

49

Switch Management...................................................................................................................................

50

Switch Mirror Configuration...........................................................................................................

51

Switch Age Time ...........................................................................................................................

52

ATM Traffic Shaping...................................................................................................................................

53

Command Line Interface............................................................................................................................

55

Chapter 6 Security Setup

 

NAT ............................................................................................................................................................

57

SNMP.........................................................................................................................................................

58

SNMP IP Filter ..............................................................................................................................

59

SNMP Password ...........................................................................................................................

59

Secure Shell...............................................................................................................................................

60

Configure SSH ..............................................................................................................................

61

Load Keys .....................................................................................................................................

62

Key Generator...............................................................................................................................

63

Firewall Scripts...........................................................................................................................................

64

Stateful Firewall..........................................................................................................................................

65

Configure Stateful Firewall ............................................................................................................

66

View Dropped Packets..................................................................................................................

67

Configure Firewall Rules ...............................................................................................................

68

Delete Firewall Rules ....................................................................................................................

70

IKE/IPSec Configuration ............................................................................................................................

71

Easy IKE/IPSec Setup ..................................................................................................................

72

Advanced IKE/IPSec Setup ..........................................................................................................

73

VPN Log On...............................................................................................................................................

80

Chapter 7 Monitoring Router

 

System Summary.......................................................................................................................................

81

Ethernet Interface Information.......................................................................................................

82

Remote Connection Information ...................................................................................................

82

IP Routing Information ..................................................................................................................

83

System Information .......................................................................................................................

83

Diagnostics.................................................................................................................................................

84

PPPoE Session.............................................................................................................................

84

Interface Information .....................................................................................................................

85

ATM Statistics................................................................................................................................

85

Routing Table Information .............................................................................................................

86

Files Information............................................................................................................................

86

Memory Usage..............................................................................................................................

87

List All Configuration Data.............................................................................................................

87

TCP/IP Statistics ...........................................................................................................................

88

SIEMENS

iii

Chapter 1 Product Specifications

Front Panel for 5930

The following table explains the LEDs that appear on the front panel of the Siemens 5930 Business Gateway.

Light

Color

Indications

 

 

 

Power

Green

Power is ON

 

Off

Power is OFF

 

 

 

Test

Yellow:

Running Power On Self Test

 

Yellow flashing:

Self Test Failure

 

Green: (2 sec blink)

Self Test successful (heartbeat)

 

Off:

Router is shut down

 

 

 

WAN

Yellow:

Establishing DSL modem link

 

Yellow flashing:

Establishing DSL throughput

 

Green:

DSL modem link successful

 

Off:

DSL modem link is shut down

 

 

 

LAN

Green flashing:

Data traffic detected

 

Green:

LAN status - OK

 

Off:

LAN status - Not OK

 

 

 

Back Panel for 5930

The following table describes the various connections on the back panel of the Siemens 5930 Business Gateway.

Connection

Function

 

 

Power

Uses a 12V DC/AC power adapter.

 

 

Ethernet Ports

Eight Ethernet T-100 switch ports (8-pin,

 

RJ-45)

 

 

Management Port

This 8-pin, RJ-45 port provides RS232

 

connectivity for console connections or a

 

dial backup analog (external) modem

 

connection.

 

 

Backup

A 6-pin RJ-11 port connects the internal

 

modem.

 

 

DSL/WAN Port

A 6-pin RJ-11 connects the DSL.

 

 

SIEMENS

1

SIEMENS 5930/5935 Business Gateway

Chapter 1 Product Specifications

User’s Guide

Hardware Specifications for 5930

 

 

Hardware Specifications for 5930

Physical Specifications

Dimensions:

11.75W x 6D x 2.25H inches

29.8W x 15.2D x 5.7H cm

Weight:

1.5 lbs.

.68 Kg.

Power Requirements

AC Voltage:100 to 120V AC or 220 to 240V AC

Frequency:50/60 Hz

Consumption:10W maximum

LAN Interface

Built-in eight port Ethernet switch with RJ-45 connectors

Green/Amber LEDs

LAN speed of 10 or 100 Mbps, full or half duplex, with auto-sense switch

Operational Environment

Temperature:40°F to 105°F

5°C to 40°C

Humidity:20% to 80% non-condensing

Processor

Motorola® MPC855T

8 MB DRAM, 4 MB Flash Memory

Motorola® MPC180 Encryption Processor

WAN Interface

One Asymmetric Digital Subscriber Line interface as follows:

ADSL, Annex A

RJ-11 with 2-3 pinout (center pair)

Serial Interface

One RS-232 asynchronous console or external modem port (RJ-45)

Agency Approvals

CE Mark

TUV

Safety:UL 1950, CSA 22.2, EN 60950

Emissions:FCC Part 15 Class B, EN55022

Immunity:EN50082-1, EN55024

SIEMENS

2

SIEMENS 5930/5935 Business Gateway

Chapter 1 Product Specifications

User’s Guide

Software Specifications for 5930

 

 

Software Specifications for 5930

Bridging

Transparent bridging including Spanning Tree protocol (IEEE 802.1D)

Bridge filters

Configuration Management

Easy Setup Web Management Interface

Microsoft® Windows configuration management via SNMP

TFTP download/upload of new software and configuration files

Performance monitor

Dynamic event and history logging

Administration through HTTP, SNMP, Telnet or VT100 terminal

Network boot uses the BootP server (RFC 2131, RFC 2132)

Dial Backup

Internal V.90 modem

Failover to external V.90 or ISDN modem via console port

Web Management Interface

User selectable fail/restore criteria

Optional modem connector (DB9 or DB25)

Supports L2TP and IPSec tunnel failover

IP Address Translation

Network renumbering (RFC 1631)

Network Address Translation (NAT/PAT)

LAN servers supported with NAT

Support for NAT inside an IPSec tunnel

Routing

TCP/IP with RIP1 (RFC 1058), RIP1 compatible and RIP2 (RFC 1389) or static routing on the LAN or WAN

Novell® IPX with RIP/SAP (RFC 1552)

DHCP client (RFC 2132)

DHCP server - Automatic assignment of IP address, mask, default gateway and DNS server addresses to workstations (RFC 2131, 2132)

DHCP relay agent (RFC 1542)

DNS relay

Multiple subnets on LAN

Virtual routing

Virtual Router Redundancy Protocol (RFC 2338)

Differentiated Services - Quality of Service provisioning

Weighted Fair Queuing (WFQ)

Differentiated Services (DiffServ)

Asynchronous Transfer Mode (ATM)

Encapsulation (IP, Bridging, and Bridge Encapsulated Routing) (RFC 1483)

PPP over ATM (LLC and VC multiplexing) (RFC 2364)

PPP over Ethernet

Classical IP (RFC 1577)

AAL5 for data

Multiple Virtual Circuits (VCs)

Virtual Circuit (VC) traffic shaping (UBR, VBR, CBR)

L610 OAM F5 loopback

Protocol Conformance Testing

RFC 1483 (Bay Networks™, Cabletron™, Cisco™, RedBack™)

PPP over ATM (Cisco, Escalate™, RedBack) (RFC 2364)

SIEMENS

3

SIEMENS 5930/5935 Business Gateway

Chapter 1 Product Specifications

User’s Guide

Software Specifications for 5930

 

 

PPP (RFC 1661)

Data compression of up to 4:1 (STAC™ LZS) (RFC 1974)

Van Jacobsen header compression (RFC 1144)

Spoofing and filtering (IP-RIP, IPX-RIP, SAP, Watchdog, serialization)

Automatic IP and DNS assignment (RFC 1877)

PPP over Ethernet (RFC 2516)

Security

Role-based management

User authentication (PAP/CHAP) with PPP (RFC 1334, RFC 1994)

Password control for Configuration Manager

SNMP password and community name reassignment

HTTP/Syslog/SNMP/Telnet port reassignment, access control list

VPN support (L2TP, IPSec, IKE, DES, 3DES)

Firewall (IP filtering)

Stateful Firewall (ICSA Compliant)

Secure Management Communications – IPsec and SSH

Radius Server support

Tacplus Server Support

VPN Hardware Acceleration support

SIEMENS

4

SIEMENS 5930/5935 Business Gateway

Chapter 1 Product Specifications

User’s Guide

Front Panel for 5935

 

 

Front Panel for 5935

The following table explains the LEDs that appear on the front panel of the Siemens 5935 Business Gateway.

Light

Color

Indications

 

 

 

Power

Green

Power is ON

 

Off

Power is OFF

 

 

 

Test

Yellow:

Running Power On Self Test

 

Yellow flashing:

Self Test Failure

 

Green: (2 sec blink)

Self Test successful (heartbeat)

 

Off:

Router is shut down

 

 

 

WAN

Yellow:

Establishing DSL modem link

 

Yellow flashing:

Establishing DSL throughput

 

Green:

DSL modem link successful

 

Off:

DSL modem link is shut down

 

 

 

LAN

Green flashing:

Data traffic detected

 

Green:

LAN status - OK

 

Off:

LAN status - Not OK

 

 

 

Back Panel for 5935

The following table describes the various connections on the back panel of the Siemens 5935 Business Gateway.

Connection

Function

 

 

Power

Uses a 12V DC/AC power adapter.

 

 

Ethernet Ports

Eight 10/100 BaseT Ethernet switch ports

 

(8-pin, RJ-45)

 

 

Management Port

This 8-pin, RJ-45 port provides RS232

 

connectivity for console connections or a

 

dial backup analog modem connection.

 

 

DSL/WAN Port

A 6-pin RJ-11 port connects the DSL.

 

 

SIEMENS

5

SIEMENS 5930/5935 Business Gateway

Chapter 1 Product Specifications

User’s Guide

Hardware Specifications for 5935

 

 

Hardware Specifications for 5935

Physical Specifications

Dimensions:

11.75W x 6D x 2.25H inches

29.8W x 15.2D x 5.7H cm

Weight:

1.5 lbs.

.68 Kg.

Power Requirements

AC Voltage:100 to 120V AC or 220 to 240V AC

Frequency:50/60 Hz

Consumption:10W maximum

LAN Interface

Built-in eight port Ethernet switch with RJ-45 connectors

Green/Amber LEDs

LAN speed of 10 or 100 Mbps, full or half duplex, with auto-sense switch

Operational Environment

Temperature:40°F to 105°F

5°C to 40°C

Humidity:20% to 80% non-condensing

Processor

Motorola® 32 MHz MPC855T

8 MB DRAM, 4 MB Flash Memory

3DES, DES, MD5, SHA hardware assist

WAN Interface

One Digital Subscriber Line interface as follows:

ADSL, Annex B

RJ-11 with 2-3 pinout (center pair)

Serial Interface

One RS-232 asynchronous console or external modem port (RJ-45)

Agency Approvals

CE Mark

TUV

Safety:UL 1950, CSA 22.2, EN 60950

Emissions:FCC Part 15 Class B, EN55022

Immunity:EN50082-1, EN55024

SIEMENS

6

SIEMENS 5930/5935 Business Gateway

Chapter 1 Product Specifications

User’s Guide

Software Specifications for 5935

 

 

Software Specifications for 5935

Bridging

Transparent bridging including Spanning Tree protocol (IEEE 802.1D)

Bridge filters

Configuration Management

Easy Setup Web Management Interface

Microsoft® Windows configuration management via SNMP

TFTP download/upload of new software and configuration files

Performance monitor

Dynamic event and history logging

Administration through HTTP, SNMP, Telnet or VT100 terminal

Network boot uses the BootP server (RFC 2131, RFC 2132)

Dial Backup

Failover to modem on console port

Web Management Interface

User selectable fail/restore criteria

Optional modem connector (DB9 or DB25)

Supports L2TP and IPSec tunnel failover

Routing

TCP/IP with RIP1 (RFC 1058), RIP1 compatible and RIP2 (RFC 1389) or static routing on the LAN or WAN

Novell® IPX with RIP/SAP (RFC 1552)

DHCP client (RFC 2132)

DHCP server - Automatic assignment of IP address, mask, default gateway and DNS server addresses to workstations (RFC 2131, 2132)

DHCP relay agent (RFC 1542)

DNS relay

Multiple subnets on LAN

Virtual routing

Virtual Router Redundancy Protocol (RFC 2338)

Differentiated Services - Quality of Service provisioning

Weighted Fair Queuing (WFQ)

Differentiated Services (DiffServ)

Asynchronous Transfer Mode (ATM)

Encapsulation (IP, Bridging, and Bridge Encapsulated Routing) (RFC 1483)

PPP over ATM (LLC and VC multiplexing) (RFC 2364)

PPP over Ethernet

Classical IP (RFC 1577)

AAL5 for data

Multiple Virtual Circuits (VCs)

Virtual Circuit (VC) traffic shaping (UBR, VBR, CBR)

L610 OAM F5 loopback

SIEMENS

7

SIEMENS 5930/5935 Business Gateway

Chapter 1 Product Specifications

User’s Guide

Software Specifications for 5935

 

 

IP Address Translation

Network renumbering (RFC 1631)

Network Address Translation (NAT/PAT)

LAN servers supported with NAT

Support for NAT inside an IPSec tunnel

Protocol Conformance Testing

RFC 1483 (Bay Networks™, Cabletron™, Cisco™, RedBack™)

PPP over ATM (Cisco, Escalate™, RedBack) (RFC 2364)

PPP (RFC 1661)

Data compression of up to 4:1 (STAC™ LZS) (RFC 1974)

Van Jacobsen header compression (RFC 1144)

Spoofing and filtering (IP-RIP, IPX-RIP, SAP, Watchdog, serialization)

Automatic IP and DNS assignment (RFC 1877)

PPP over Ethernet (RFC 2516)

Security

Role-based management

User authentication (PAP/CHAP) with PPP (RFC 1334, RFC 1994)

Password control for Configuration Manager

SNMP password and community name reassignment

HTTP/Syslog/SNMP/Telnet port reassignment, access control list

VPN support (L2TP, IPSec, IKE, DES, 3DES)

Firewall (IP filtering)

Stateful Firewall (ICSA Compliant)

Secure Management Communications – IPsec and SSH

Radius Server support

Tacplus Server Support

VPN Hardware Acceleration support

SIEMENS

8

Chapter 2

Installation

This chapter describes the steps you must take to install and configure the various components in your network to utilize the Siemens Business Gateway. This includes setting up the hardware connections to the Internet router, configuring the PC to use the Internet router for Internet access, and setting up the Internet router configuration. Before beginning installation, make sure you meet all installation requirements.

Installation Requirements

Before beginning the installation and configuration of the various components on the network, make sure you received all the package contents, meet the basic PC requirements, and have the necessary information from your network Service Provider.

Package Contents

Your package should contain the items listed below. If you determine anything to be damaged or missing, please contact the dealer from whom the equipment was purchased.

One Siemens 5930 or 5935 Business Gateway

One Siemens Documentation CD-ROM

One AC power supply module and cord

One Ethernet cable, RJ-45

One DSL cable, RJ-11, purple label

One RJ-45 to DB-9 serial port adapter (console)

5930 or 5935 Business Gateway Quick Start Guide

Safety and Certifications document

PC Requirements

At a minimum, your computer must be equipped with the following to successfully install the broadband Internet router.

CD-ROM Drive

Ethernet network interface card

TCP/IP network protocol installed on your PC

Web browser

Terminal emulation software, if you want to configure your router via your computer’s serial port before placing it into service on a network.

SIEMENS

9

SIEMENS 5930/5935 Business Gateway

Chapter 2 Installation

User’s Guide

Installation Requirements

 

 

Network Service Provider Requirements

Your Network Service Provider will provide you with information to configure your router’s WAN connection. Depending upon the type of service that you ordered, you will need some of the items from the following list. Contact your Network Service Provider for specific details on the items you should receive.

DNS address

One or more LAN IP addresses and a subnet mask

Protocol to use, from one of the following:

PPP (Point-to-Point Protocol), with a user name and password

PPPoE (PPP over Ethernet)

RFC 1483 (SNAP Encapsulation)

RFC 1483 MER (MAC Encapsulated Routing, requiring a WAN gateway address)

VCI (PVC) numbers

Network options:

Bridging

IP Routing (requires a WAN IP address and subnet mask)

SIEMENS

10

SIEMENS 5930/5935 Business Gateway

Chapter 2 Installation

User’s Guide

Hardware Installation

 

 

Hardware Installation

You may position the Siemens broadband router at any convenient location where it will be well ventilated. Do not stack it with other devices or place it on the carpet. You can connect the router to an existing Ethernet port on your computer.

To connect the SpeedStream device via the Ethernet interface, your computer must have an Ethernet adapter (also called a network interface card, or NIC) installed. If your computer does not have this adapter, install it before proceeding further. Refer to your Ethernet adapter documentation for complete installation instructions. Once you verify installation of an Ethernet adapter, perform the following procedure to connect the router to your computer.

1.With the PC powered off, connect the Ethernet cable to an Ethernet port on the router.

2.Connect the other end of the Ethernet cable to the Ethernet port on the PC.

3.Connect the DSL cable (resembles a telephone cord) to the DSL port on the rear of the router. To reduce the risk of fire, use only 26 AWG gauge telecommunication cord to connect your DSL port on your router to a DSL telephone jack.

4.Plug the other end of the DSL cable into the phone jack.

5.Connect the power adapter to the rear of the router.

6.Plug the power adapter into the electrical wall outlet.

7.Flip the power switch on the router.

8.Power on all connected computers.

You can now configure the TCP/IP settings as detailed in the PC Configuration section.

SIEMENS

11

SIEMENS 5930/5935 Business Gateway

Chapter 2 Installation

User’s Guide

PC Configuration

 

 

PC Configuration

Your PC must be configured to use the TCP/IP protocol suite over the Internet, and to accept Dynamic Host Configuration Protocol address assignments from the router. Although this is the default settings for the PC, it is a good idea to verify that they have not been changed.

Each supported PC Operating System varies slightly in how the configuration windows are presented. Select the Operating System installed on the PC connected to the router from the list below and follow the associated procedure.

Windows 98/ME

Windows NT 4

Windows 2000

Windows XP

Mac OS 9.x

Mac OS X

 

 

Linux OS

 

 

Windows 98/ME

1.Click Start >Control Panel > Network. This displays the

Configuration tab on the Network window.

2.Select TCP/IP protocol for your network card.

3.Click Properties. This displays the TCP/IP Properties window.

4.Click the IP Address tab.

5.Ensure that the Obtain an IP address automatically option is selected. This is the default Windows setting.

6.Click OK to close each dialog.

7.Restart the PC to ensure it obtains an IP address from the router.

8.Configure the router.

SIEMENS

12

SIEMENS 5930/5935 Business Gateway

Chapter 2 Installation

User’s Guide

PC Configuration

 

 

Windows NT 4

1.On your desktop, right click on the Network Neighborhood icon. This displays the Network window.

2.Click the Protocols tab.

3.Select TCP/IP Protocol from the Network Protocols list.

4.Click Properties. This displays the Microsoft TCP/IP Properties window.

5.Click the IP Address tab.

6.On the IP Address tab, select Obtain an IP address from a DHCP server.

7.Click OK to close each dialog.

8.Restart the PC to ensure it obtains an IP address from the router.

9.Configure the router.

SIEMENS

13

SIEMENS 5930/5935 Business Gateway

Chapter 2 Installation

User’s Guide

PC Configuration

 

 

Windows 2000

1.Select Start >Settings >Control Panel. This displays the Control Panel window.

2.Double-click the Network and Dial-up Connection icon. This displays the Network and Dialup Connection window.

3.Right-click Local Area Connections and select Properties. This displays the Local Area Connections Properties window.

4.Select Internet Protocol (TCP/IP) from the list of components.

5.Click Properties. This displays the Internet Protocol (TCP/IP)

Properties window.

6.Ensure that the Obtain an IP address automatically and Obtain DNS server address automatically options are selected.

7.Click OK to close each dialog.

8.Restart the PC to ensure it obtains an IP address from the router.

9.Configure the router.

SIEMENS

14

SIEMENS 5930/5935 Business Gateway

Chapter 2 Installation

User’s Guide

PC Configuration

 

 

Windows XP

1.Click Start >Control Panel. This displays the Control Panel window.

2.Double-click the Network Connections icon. This displays the Network Connection window.

3.Right-click Local Area Connection, then click Properties. This displays the Local Area Connection Properties window.

4.Select Internet Protocol TCP/IP.

5.Click Properties. This displays the Internet Protocol (TCP/IP) Properties window.

6.Ensure the Obtain an IP address automatically and Obtain DNS server address automatically options are selected.

7.Restart the PC to ensure it obtains an IP address from the router.

8.Configure the router.

SIEMENS

15

SIEMENS 5930/5935 Business Gateway

Chapter 2 Installation

User’s Guide

PC Configuration

 

 

Mac OS 9.x

1. Click Apple -> Control Panels -> TCP/IP. This displays the TCP/IP Control Panel window.

2.Select Ethernet from the Connect via drop-down menu.

3.Select Using DHCP Server from the Configure drop-down menu.

4.Complete the fields shown with any information supplied by your service provider.

5.Close window and save changes.

6.Configure the router.

SIEMENS

16

SIEMENS 5930/5935 Business Gateway

Chapter 2 Installation

User’s Guide

PC Configuration

 

 

Mac OSX

1. Click Apple -> System Preferences. This displays the System Preferences window.

2. Double-click the Network icon under the Internet & Network section. This displays the Network window.

3.Select Ethernet from the Connect via drop-down menu.

4.Select Using DHCP Server from the Configure drop-down menu.

5.Enter any information supplied by your service provider.

6.Click Apply Now to save and exit the Network window.

7.Configure the router.

SIEMENS

17

Siemens 5935, 5930 User Manual

SIEMENS 5930/5935 Business Gateway

Chapter 2 Installation

User’s Guide

PC Configuration

 

 

Linux

1. From a terminal window, run linuxconfig. This displays the Config window.

2.Click the Adaptor tab.

3.Enter any information specified by your service provider in the fields under the appropriate Adapter tab.

4.When settings are completed, click Accept. This displays the Status of the system tab.

5.To update the system status, ensure that the Activate the changes button is highlighted, then click Act/ Changes.

6.Configure the router.

SIEMENS

18

SIEMENS 5930/5935 Business Gateway

Chapter 2 Installation

User’s Guide

Configuring the Router

 

 

Configuring the Router

The Siemens Business Class Router family of products provides two user interfaces: a Web Management Interface and a console-based Command Line Interface (CLI). The Web Management Interface uses an HTTP server housed in the router. Using this server, you can connect to and manage the router using your Web browser. The Web Management Interface is accessible through most HTML browsers, though Internet Explorer 4.0 or Netscape 4.0 and higher are recommended. Refer to the Technical Reference Guide for details on managing the router through the CLI.

Establish Connection

To establish a connection from your computer to the router through your Web browser:

1.Open your Internet Explorer or Netscape Navigator Web browser.

2.In the Address bar, enter the default router IP address: 192.168.254.254. This displays the Login Dialog page.

3.Enter the administrative User name and Password. The default settings are User name: superuser and Password: admin. This displays the Router Information page.

SIEMENS

19

SIEMENS 5930/5935 Business Gateway

Chapter 2 Installation

User’s Guide

Configuring the Router

 

 

Router Information Page

The Router Information Page is the first page you encounter after logging into the router.

The Router Information page displays basic router information and configuration settings. On the Router Information page, the following information is presented:

Router Information: Including the model number, software version number, and hardware description.

Router Configuration: Displays router configuration details such as LAN IP address, WAN data and voice PVC (ATM), WAN protocol and WAN network settings.

In the left navigation pane of this page, there are configuration, diagnostic, and status and statistic options for the router. In this document, these features are grouped according to User Access Control, Advanced Router Functions, Security, and Monitoring Health and Status.

Use the table below to locate detailed instructions for the desired function.

To do this:

Refer to:

Perform Easy Setup

Chapter titled "Easy Setup"

Configure users on the router.

Chapter titled "User Setup"

Configure advanced features.

Chapter titled "Advanced Setup"

Configure security features.

Chapter titled "Security Setup"

Monitor the health of the router.

Chapter titled "Monitoring Router"

Manage router using Command Line Interface

Technical Reference Manual

SIEMENS

20

Chapter 3

Easy Setup

This chapter describes how to define router configuration settings using the Easy Setup Wizard. These settings control access to the Wide Area Network (WAN) and Local Area Network (LAN). During the Easy Setup procedure, you will be prompted to specify configuration parameters that may require information from your service provider.

Access Easy Setup Wizard

To access the Easy Setup Wizard, click Easy Setup in the left navigation pane of the Router Information window. This wizard will walk you through the configuration screens necessary to setup the router. You can exit the Easy Setup Wizard at anytime by clicking Cancel on the bottom of the configuration page. If the wizard is cancelled, no changes will be made and you will need to begin again.

Select Protocol

When you click Easy Setup in the left navigation pane of the Router Information page, the WAN Interface page is displayed. This page is used to enter and review information about Wide Area Network (WAN) settings.

To configure the WAN interface:

1.in Data DLCI (Data Link Connection Identifier), enter the logical connection between the router and the Service provider, as designated by your Service Provider.

2.From the Wan Protocol list, select the protocol to use for the WAN connection.

3.Click Next to continue. This displays the page required to configure the selected protocol. In the list below, click on the protocol you selected to jump to the appropriate page.

Point-to-Point Protocol over ATM

Point-to-Point Protocol over Ethernet over PPPoA

Point-to-Point Protocol over Ethernet over RFC1483

RFC 1483

RFC 1483 MAC Encapsulated Routing

SIEMENS

21

SIEMENS 5930/5935 Business Gateway

Chapter 3 Easy Setup

User’s Guide

Select Protocol

 

 

Point-to-Point Protocol over ATM

If you selected Point-to-Point Protocol over ATM from the Wan Interface page, the Point-to-Point Protocol page is displayed when you click Next.

To configure Point-to-Point Protocol:

1.Enter PPP User Name and Password to use for authentication when establishing a WAN connection using PPP protocol.

2.Select one or more of the following PPP Networking options:

Bridging Enabled:

Forward all traffic for remote hosts that is not routed to the WAN (non-IP). If bridging is enabled, you can optionally select Only bridge PPPoE traffic. If selected, only PPPoE traffic is bridged; all other traffic is stopped.

3.IP Routing Enabled:

Route all IP traffic to remote hosts.

4.If you enabled IP routing, optionally select one or more of the following:

NAT Enabled:

Network Address Translation (NAT) allows multiple workstations on your LAN to share a single, public IP address. All outgoing traffic appears to originate from the router’s IP address.

Block Net BIOS Traffic:

NetBIOS is a PC networking protocol that can keep network connections open inadvertently. To avoid excess connection charges, such traffic should be blocked on any metered network service.

5.Click Next. This displays the Dynamic Host Configuration Protocol page.

SIEMENS

22

SIEMENS 5930/5935 Business Gateway

Chapter 3 Easy Setup

User’s Guide

Select Protocol

 

 

Point-to-Point Protocol over Ethernet over PPPoA

If you selected Point-to-Point Protocol over Ethernet over PPPoA from the Wan Interface page, the Point- to-Point Protocol over Ethernet over PPPoA page is displayed when you click Next.

To configure Point-to-Point Protocol over Ethernet over PPPoA:

1.Enter PPPoE User Name and Password to use for authentication when establishing a WAN connection using PPPoE protocol.

2.In Service Name, enter the domain name of your network service provider. Use * as a default (for all services).

3.In PPPoE Timer, enter the number of seconds of inactivity that must elapse before the PPP connection closes. This helps to limit connection charges from your service provider during times of inactivity. The default entry of “permanent” will keep the PPP connection open constantly, with no time out interval.

4.Optionally select PPPoE only Filter. When selected, all traffic on the bridge is filtered to allow PPPoE only. Select this option if you will only connect to your network service using PPPoE.

5.If you are using PPPoE over PPPoA, enter the PPPoA Username and Password.

6.Click Next. This displays the Dynamic Host Configuration Protocol page.

SIEMENS

23

Loading...
+ 65 hidden pages