VPC-TP1010
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
Note:
This equipment has been tested and found to comply with the limits for Class B digital
devices, pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.This
equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with Class B limits in Subpart B of Part 15 of
the FCC rules.
Do not make any changes or modifications to the equipment unless otherwise specified
in the manual. If such changes or modifications should be made, you could be required
to stop operation of the equipment.
Notice
If static electricity or electromagnetism causes data transfer to discontinue midway (fail),
restart the application or disconnect and connect the communication cable (USB, etc.)
again.
EN-1
READ THIS FIRST
Trademark Information
Microsoft® and Windows® are U.S. registered trademarks of Microsoft Corporation.
Pentium
Macintosh is a trademark of Apple Inc.
microSD™ is a trademark.
microSDHC™ is a trademark.
Other names and products may be trademarks or registered trademarks of their respective
Product Information
Product design and specifications are subject to change without notice. This includes
The product and accessories that come with your camera may be different from those
The illustrations in this manual are for the purpose of explanation and may differ from the
The manufacturer assumes no liability for any errors or discrepancies in this user manual.
®
is a registered trademark of Intel Corporation.
owners.
primary product specifications, software, software drivers, and user’s manual. This User
Manual is a general reference guide for the product.
described in this manual. This is due to the fact that different retailers often specify slightly
different product inclusions and accessories to suit their market requirements, customer
demographics, and geographical preferences. Products very often vary between retailers
especially with accessories such as batteries, chargers, AC adapters, memory cards,
cables, pouches, and language support. Occasionally a retailer will specify a unique
product color, appearance, and internal memory capacity. Contact your dealer for precise
product definition and included accessories.
actual design of your camera.
Before capturing those important shots, be sure to first take a
test shot to confirm that your camera is set up and ready to go
Sanyo Electric shall not be held responsible for any problems resulting from the use of this
camera.
Sanyo Electric declines all responsibility for damages due to improper use of the camera,
failure to adhere to the instructions given in this manual, or repairs or changes done by
those other than a technician authorized by the manufacturer.
Sanyo Electric shall not be held responsible for any damage caused by optional devices
or consumable items used with the camera other than those supplied with the camera or
those specified by Sanyo Electric.
Sanyo Electric shall not be held responsible for any losses or loss of revenue resulting
from the loss of data caused by the malfunction, or the repairing of a malfunction, of the
camera.
The images captured with this camera will differ in quality from pictures taken with a
standard film camera.
EN-2
SAFETY INSTRUCTIONS
Read and understand all Warnings and Cautions before using this product.
Warnings
If foreign objects or water have entered the camera, turn the power off
and remove the battery.
Continued use might cause fire or electric shock. Consult the store of
purchase.
If the camera has fallen or its case has been damaged, turn the power
off and remove the battery.
Continued use might cause fire or electric shock. Consult the store of
purchase.
Do not disassemble, change or repair the camera.
This might cause fire or electric shock. For repair or internal inspection, ask
the store of purchase.
Do not use the camera in areas near water.
This might cause fire or electric shock. Take special care during rain, snow,
on the beach, or near the shore.
Do not place the camera on inclined or unstable surfaces.
This might cause the camera to fall or tilt over, causing damage.
Keep the battery out of the reach of children.
Swallowing the battery might cause poisoning. If the battery is accidentally
swallowed, immediately consult a physician.
Do not use the camera while you are walking, driving or riding a
motorcycle.
This might cause you to fall over or result in traffic accident.
Please use battery with complete external seals.
Do not use battery from which the seals have been damaged or removed.
This may cause leakage, explosion, or injury.
EN-3
Cautions
Insert the battery paying careful attention to the polarity (+ or –) of the
terminals.
Inserting the battery with its polarities inverted might cause fire and injury, or
damage to the surrounding areas due to the battery rupturing or leaking.
Do not fire the flash close to anyone’s eyes.
This might cause damage to the person’s eyesight.
Do not subject the LCD monitor to impact.
This might damage the glass on the screen or cause the internal fluid to leak.
If the internal fluid enters your eyes or comes into contact with your body or
clothes, rinse with fresh water. If the internal fluid has entered your eyes,
consult a physician to receive treatment.
Camera is a precision instrument. Do not drop it, strike it or use
excessive force when handling the camera.
This might cause damage to the camera.
Do not use the camera in humid, steamy, smoky, or dusty places.
This might cause fire or electric shock.
Do not remove the battery immediately after long period of continuous use.
The battery becomes hot during use. Touching a hot battery might cause
burns.
Do not wrap the camera or place it in cloth or blankets.
This might cause heat to build up and deform the case, resulting in fire. Use
the camera in a well-ventilated place.
Do not leave the camera in places where the temperature may rise
significantly, such as inside a car.
This might adversely affect the case or the parts inside, resulting in fire.
Before you move the camera, disconnect cords and cables.
Failure to do this might damage cords and cables, resulting in fire and electric
shock.
Touch panel is designed for operating the camera by touching the LCD monitor (touch panel)
with your finger. You can operate by directly tapping the monitor with your finger. Do not press
on the LCD monitor with hard pointed tips, such as ball point pens.
In such situations below, even if you tap the touch panel, it won’t have any reaction:
Operate the camera when it is still in the pouch.
Tap with your fingernail.
Some other things were dropped onto the screen.
Tap on the liquid crystal protection sheet. (Some liquid crystal protection sheets may
impair visibility or operability.)
Please do not:
Operate the touch panel with wet finger.
Press the LCD monitor too hard.
Stick adhesive things to the touch panel.
NOTES ON USING TOUCH PANEL
EN-4
Warning:
TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE
FOR AMERICAN USERS
The following advisory is included in accordance with the laws of the State of California
(USA):
WARNING:
This product contains a chemical known to the State of California to cause cancer, birth
defects or other reproductive harm.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designated to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
* Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void the userís authority to operate the equipment.
EN-5
FOR CANADIAN USERS
This Class B digital apparatus complies with Canadian ICES-003
FOR EU USERS
The symbol mark and recycling systems described below apply to
EU countries and do not apply to countries in other areas of the
world.
Your SANYO product is designed and manufactured with high
quality materials and components which can be recycled and/or
reused.
The symbol mark means that electrical and electronic equipment,
batteries and accumulators, at their end-of-life, should be disposed
of separately from your household waste.
Note:
If a chemical symbol is printed beneath the symbol mark, this
chemical symbol means that the battery or accumulator contains a
heavy metal at a certain concentration.
This will be indicated as follows: Hg: mercury, Cd: cadmium, Pb:
lead
In the European Union there are separate collection systems for
used electrical and electronic equipment, batteries and
accumulators.
Please, dispose of them correctly at your local community waste
collection/recycling centre.
Please, help us to conserve the environment we live in!
Manufacturer and Address
SANYO Electric Co., Ltd.
5-5, Keihan-hondori, 2-chome,
Moriguchi City, Osaka, Japan
EN-6
Authorized Representative and Address
SANYO Sales & Marking Europe GmbH
Stahlgruberring 4, D-81829 Munich, Germany
Symbols used in this manual
Points giving some extended instructions or special points to pay attention to.
You many find the answers to questions or problems concerning camera operation in
the sections “Troubleshooting”.
FCC information
Test e d To C o m pl y
With FCC Standards
FOR HOME OR OFFICE USE
Declaration of Conformity
Model number: VPC-TP1000/TP1010
Trade Name: SANYO
Responsible party: SANYO FISHER COMPANY
Address: 21605 Plummer Street
Telephone No.: (818) 998-7322
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
Chatsworth, California 91311
may cause undesired operation.
Canadian ICES-003 information
This class B digital apparatus complies with Canadian ICES-003.
EN-7
Notes on Battery Usage
When you use the battery, carefully read and strictly observe the Safety Instructions
and the notes described below:
Use only the specified battery.
Avoid extremely cold environments as low temperatures can shorten the battery life
and reduce camera performance.
When you are using a new rechargeable battery or a rechargeable battery that has
not been used for an extended period of time, it may affect the number of images
that can be captured. Therefore, to maximize its performance and lifetime, we
recommend that you fully charge the battery and discharge it for at least one
complete cycle before use.
The battery may feel warm after a long period of continuous use of the camera or the
flash. This is normal and not a malfunction.
The camera may feel warm after a long period of continuous use. This is normal and
not a malfunction.
If the battery is not to be used for a long period of time, remove it from the camera to
prevent leakage or corrosion and store it after no battery power is left. Stored for a
long time in a fully charged condition, its performance may be impaired.
Always keep the battery terminals clean.
There is a risk of explosion if the battery is replaced by an incorrect type.
Dispose of used battery according to the recycle instructions.
Charge the rechargeable battery fully before using for the first time.
To prevent short-circuiting or fire, keep the battery away from other metal objects
when carrying or storing.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
- SANYO Li-ion Battery, 3.7V, 700mAh
EN-8
CONTENTS
10 INTRODUCTION
10 Overview
10 Package Contents
11 GETTING TO KNOW YOUR
CAMERA
11 Front View
12 Button Operation
13 LCD Monitor Display
15 GETTING STARTED
15 Preparation
16 Charging the Battery
17 Initial Settings
19 CAPTURE MODE
19 Capturing Images
20 Setting the Scene Mode
21 Multi-Focus
22 Setting the Panorama Mode
23 Taking Images When the Smile
Feature Is On
23 Find Blur
24 Recording Shots into Multiple Image
Layout
24 Recording Shots using Face
Detection Technology
25 VIDEO MODE
25 Recording Video Clips
25 Playing Back Video Clips
26 PLAYBACK MODE
26 Playing Back Still Images
26 Quckly review
27 Thumbnail Display
27 Face enlarge
28 Removing Red-eye
28 Dynamic Lighting Feature
29 Attaching Voice Memos
30 Protecting Images
31 Photo Frame
31 Erasing Images
32 MENU OPTIONS
32 Capture Menu
35 Video Menu
36 Playback Menu
38 Setup Menu
40 TRANSFERRING FILES TO
YOUR COMPUTER
40 Downloading Your Files
41 EDITING SOFTWARE
INSTALLATION
42 SPECIFICATIONS
43 APPENDIX
43 Possible Number of Shots
44 Troubleshooting
45 Connecting to a PictBridge Compliant
Printer
EN-9
INTRODUCTION
Overview
Congratulations on your purchase of the new digital camera.
Capturing high-quality digital images is fast and easy with this state-of-the-art smart
camera. Equipped with a 10.0-megapixel CCD, this camera is capable of capturing
images with a resolution of up to 3648 x 2736 pixels.
Package Contents
Carefully unpack your camera and ensure that you have the following items:
Common Product Components:
Digital Camera
Quick Guide
Bundled CD-ROM (Application Software and INSTRUCTION Manual )
USB cable
Camera strap
Camera pouch
Rechargeable lithium-ion battery
Battery charger
AC adapter for battery charger
Optional Accessories:
microSD/SDHC memory card
Accessories and components may vary by retailer.
EN-10
GETTING TO KNOW YOUR CAMERA
Front View
2
1
8
1. Zoom lever
2. Shutter button
3. ON/OFF Power button
4. Status LED
5. Self-timer LED
6. Lens
7. Flash
8. Microphone
4
3
7
5
6
EN-11
Button Operation
1
2
3
4
Item
Capture Mode Video Mode Playback Mode
1. Playback mode Playback mode Still image: to capture mode
2. Capture menu Video menu Playback menu
3. Face Detect -- --
4. Delete Delete Delete
EN-12
Function
Video clip: to video mode
LCD Monitor Display
Capture mode
1. Zoom status
2. Available number of shots
3. Storage media
[r] Internal memory
(no card)
[ ] microSD/SDHC
4. Battery condition
5. ISO
6. Image quality
7. White balance
8. Capture mode icon
[ ] Single
[T] Continuous
[U] AEB (Auto
[-] Album Shot
memory card
Full battery power
[l]
[o] Medium battery
power
Low battery power
[n]
[m]
No battery power
[2]Auto
[:]ISO 64
[5]ISO 100
[7]ISO 200
[9]ISO 400
[0]ISO 800
[;]ISO 1600
[]ISO 3200
[]Fine
[ ] Standard
[ ] Economy
[@]Auto
[$] Incand.
[&] Fluoresc.1
[*] Fluoresc.2
[%] Daylight
[#] Cloudy
[(] Manual WB
Exposure
Bracketing)
[.] Cont.flash
[+]Pre-shot
[,] Coupl.shot
9. Quick shot
10. Image size resolution
11. Self-timer icon
12. [s] Exposure
13. Flash mode
14. Focus setting
15. Date and time
16. [ ] Histogram
17. Main focus area
18. Slow shutter warning
19. Mode icon / Scene mode
[/]Burst
[x] 640 x 480
[ ] 1600 x1200
[ ] 2304x1728
[ ] 2816 x 2112
[ ] 3648 x 2736
[f] 2 sec.
[g] 10 sec.
[h] 10+2 sec.
[] Self-portrait
[i]off
compensation
[a]Flash On
[b]Auto
[c]Red-eye
[d] Flash Off
[_] Pre-flash
[`] Slow Sync
[O]Macro
[K]Auto
[Q] Infinity
[ ] Multi-focus
[] Auto
[ ] Video
[]Smile Detection
[]Anti-shake
[ ] Panorama
[ ] Portrait Man
[ ] Portrait Lady
[ ] Landscape
[ ] Sports
[ ] Night Portrait
[ ] Night Scene
[ ] Candlelight
[]Fireworks
[] Text
[ ] Sunset
[]Sunrise
[ ] Splash Water
[]Flow Water
[]Snow
[]Beach
[]Pets
[ ] Natural Green
[ ] Program AE
Single touch the above icon (except for items 1 to 9, 15 to 18) to display all options. Tap your
favorite one to confirm, and the setting will be changed.
EN-13
Video mode
00:00:00 / 02:28:49
110-0201
13:15
F2.8
1/3
2009.01.01
+0.3
110-0201
1. Mode icon
2. Zoom status
3. Storage media
4. Battery condition
5. Sound off icon
6. Video quality
7. Date and time
8. Available recording time/Elapsed time
9. Video resolution
* Items 2 to 8 can not be selected.
Playback mode - Still image playback
1. Voice memo
2. Protect icon
3. Folder number
4. File number
5. Storage media
6. Battery condition
7. ISO
8. Image quality
9. Image size resolution
10. Exposure value
11. Quickly review
12. Shutter speed value
13. Aperture value
14. Date and time
15. Play mode
16. Histogram
* Items 1 to 10, 12 to 14 & 16can not be selected.
Playback mode - Video playback
1. Protect icon
2. Folder number
3. File number
4. Storage media
5. Battery condition
6. Fast forward icon
7. Play mode
8. Quickly review
9. Volume mode
10. Total recorded time
11. Video status bar
12. Elapsed time
13. Control panel icon
14. Fast rewined icon
* Items 1 to 5 & 10 to 12 can not be selected.
00:00:00 / 02:28:49
00:00:00 / 02:28:49
110-0201
110-0201
13:15
13:15 F2.8
1/3
2009.01.01
00:00:00 02:28:49
F2.8 1/32009.01.01
110-0201
110-0201
+0.3
+0.3
EN-14
Loading...