Sanyo PLC - 12NL, PLC - 12EL, PLC-XF12N, PLC - 12BL User Manual

Multimedia Projector

MODEL PLC-XF12N/12NL PLC-XF12E/12EL PLC-XF12B/12BL

Owner's Manual

TO THE OWNER

Before operating this projector, read this manual thoroughly and operate the projector properly.

This projector provides many convenient features and functions. Operating the projector properly enables you to manage those features and maintains it in better condition for a considerable time.

Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other accidents.

If your projector seems to operate improperly, read this manual again, check operations and cable connections and try the solutions in the “Trouble-shooting” section of the end of this booklet. If the problem still persists, contact the sales dealer where you purchased the projector or the service center.

SAFETY PRECAUTIONS

WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

●This projector produces intense light from the projection lens. Do not stare directly into the lens as possible. Eye damage could result. Be especially careful that children do not stare directly into the beam.

●This projector should be set in the way indicated. If not, it may result in a fire hazard.

● Take appropriate space on the top, sides and rear of the projector				SIDE and TOP				REAR
cabinet for allowing air circulation and cooling the projector. 20cm
Minimum distance should be taken. If the projector is to be built
into a compartment or similarly enclosed, the minimum distances
must be maintained. Do not cover the ventilation slot on the
projector. Heat build-up can reduce the service life of your				50cm		50cm			1m
projector, and can also be dangerous.

●Do not put any flammable object or spray can near the projector, hot air is exhausted from the ventilation holes.

●The Remote Control Unit, supplied to this projector, emits the laser beam as the Laser Pointer function from the Laser Light Window while pressing the LASER button. Do not look into the Laser Light Window or shine the laser beam on yourself or other people. Eye damage may result.

●If the projector is not to be used for an extended time, unplug the projector from the power outlet.

READ AND KEEP THIS OWNER'S MANUAL FOR LATER USE.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USERSERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.

THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE OWNER'S MANUAL WITH THIS UNIT.

2

SAFETY PRECAUTIONS

All the safety and operating instructions should be read before the product is operated.

Read all of the instructions given here and retain them for later use. Unplug this projector from AC power supply before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.

Follow all warnings and instructions marked on the projector.

For added protection to the projector during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage due to lightning and power line surges.

Do not expose this unit to rain or use near water... for

example, in a wet basement, near a swimming pool, etc...

Do not use attachments not recommended by the manufacturer as they may cause hazards.

Do not place this projector on an unstable cart, stand, or table. The projector may fall, causing serious injury to a child or adult, and serious damage to the projector. Use only with a cart or stand recommended by the manufacturer, or sold with the projector. Wall or shelf mounting should follow the manufacturer's instructions, and should use a mounting kit approved by the manufacturers.

An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

Slots and openings in the back and bottom of the cabinet are provided for ventilation, to insure reliable operation of the equipment and to protect it from overheating.

The openings should never be covered with cloth or other materials, and the bottom opening should not be blocked by placing the projector on a bed, sofa, rug, or other similar surface. This projector should never be placed near or over a radiator or heat register.

This projector should not be placed in a built-in installation such as a book case unless proper ventilation is provided.

Never push objects of any kind into this projector through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the projector.

This projector should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied, consult your authorized dealer or local power company.

Do not overload wall outlets and extension cords as this can result in fire or electric shock. Do not allow anything to rest on the power cord. Do not locate this projector where the cord may be damaged by persons walking on it.

Do not attempt to service this projector yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

Unplug this projector from wall outlet and refer servicing to qualified service personnel under the following conditions:

a.When the power cord or plug is damaged or frayed.

b.If liquid has been spilled into the projector.

c.If the projector has been exposed to rain or water.

d.If the projector does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the projector to normal operation.

e.If the projector has been dropped or the cabinet has been damaged.

f.When the projector exhibits a distinct change in performance-this indicates a need for service.

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or injury to persons.

Upon completion of any service or repairs to this projector, ask the service technician to perform routine safety checks to determine that the projector is in safe operating condition.

Voor de klanten in Nederland

Bij dit product zijn batterijen geleverd.

Wanneer deze leeg zijn, moet u ze niet weggooien maar inleveren als KCA.

3

COMPLIANCES

Federal Communication Commission Notice

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

AC POWER CORD REQUIREMENT

The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.

AC Power Cord for the United States and Canada :

AC Power Cord used in the United States and Canada is listed by the Underwriters Laboratories (UL) and certified by the Canadian Standard Association (CSA).

AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the plug will fit into the power outlet. Do not try to defeat this safety feature.

Should you be unable to insert the plug into the outlet, contact your electrician.	GROUND

AC Power Cord for the United Kingdom :

This cord is already fitted with a moulded plug incorporating a fuse, the value of which is indicated on the pin face of the plug. Should the fuse need to be replaced, an ASTA approved BS 1362 fuse must be used of the same rating, marked thus ASA . If the fuse cover is detachable, never use the plug with the cover omitted. If a replacement fuse cover is required, ensure it is of the same colour as that visible on the pin face of the plug (i.e. red or orange). Fuse covers are available from the Parts Department indicated in your User Instructions. If the plug supplied is not suitable for your socket outlet, it should be cut off and destroyed.

The end of the flexible cord should be suitably prepared and the correct plug fitted. (See Over)

WARNING : A PLUG WITH BARED FLEXIBLE CORD IS HAZARDOUS IF ENGAGED IN A LIVE SOCKET OUTLET.

The Wires in this mains lead are coloured in accordance with the following code: Green-and-yellow ············Earth

Blue ·································Neutral Brown ······························Live

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows:

The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or coloured green or green-and-yellow.

The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.

The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.

WARNING : THIS APPARATUS MUST BE EARTHED.

THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.

4

TABLE OF CONTENTS

FEATURES AND DESIGN	6
PREPARATION	7
NAME OF EACH PART OF THE PROJECTOR	7
SETTING-UP THE PROJECTOR	8
CONNECTING THE AC POWER CORD	8
POSITIONING THE PROJECTOR	9
PICTURE LEVEL AND TILT ADJUSTMENT	10
MOVING THE PROJECTOR	10

COMPUTER MODE	36
SELECTING COMPUTER MODE	36
SELECTING COMPUTER SYSTEM	36
COMPATIBLE COMPUTER SPECIFICATIONS	37
PC ADJUSTMENT	38
PICTURE IMAGE ADJUSTMENT	40
NORMAL FUNCTION	41
AUTO IMAGE ADJUSTMENT	41
PICTURE POSITION ADJUSTMENT	42
PICTURE SCREEN ADJUSTMENT	43

CONNECTING THE PROJECTOR

TERMINAL OF THE PROJECTOR CONNECTING THE COMPUTER CONNECTING THE VIDEO EQUIPMENT

BEFORE OPERATION

CONTROLS AND INDICATORS OPERATION OF THE REMOTE CONTROL

WIRELESS REMOTE CONTROL UNIT WIRELESS/WIRED REMOTE CONTROL UNIT

OPERATING ON-SCREEN MENU

HOW TO OPERATE ON-SCREEN MENU FLOW OF ON-SCREEN MENU

MENU BAR

BASIC OPERATION

TURNING ON / OFF THE PROJECTOR

TO TURN ON THE PROJECTOR

TO TURN OFF THE PROJECTOR

ADJUSTING THE IMAGE

ZOOM ADJUSTMENT

FOCUS ADJUSTMENT

LENS SHIFT FUNCTION DIGITAL ZOOM FUNCTION NORMAL PICTURE FUNCTION FREEZE PICTURE FUNCTION NO SHOW FUNCTION P-TIMER FUNCTION

AUTO IMAGE ADJUSTMENT CURSOR FUNCTION

11	VIDEO MODE	44
11	SELECTING VIDEO MODE	44
13	SELECTING VIDEO SOURCE	44
21	SELECTING COLOR SYSTEM	45
	PICTURE IMAGE ADJUSTMENT	46
23	NORMAL FUNCTION	47
	PICTURE SCREEN ADJUSTMENT	47

	23	SETTING	48
	25
	25	SETTING MENU	48
	28	SETTING LANGUAGE	49
	30
	30
	30	APPENDIX	50
	31
	32
	32	AIR FILTER CARE AND CLEANING	51
	32
		LAMP REPLACEMENT	52
	32
		CLEANING THE PROJECTION LENS	53
	33
		TROUBLESHOOTING	53
	33
		TECHNICAL SPECIFICATIONS	55
	33
	33
	33
	33
	34
	34
	34
	34
	34

SOUND ADJUSTMENT	35
DIRECT OPERATION	35
MENU OPERATION	35

TRADEMARKS

●Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.

●IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.

●Windows and PowerPoint are registered trademarks of Microsoft Corporation.

●Each name of corporations or products in the owner's manual is a trademark or a registered trademark of its respective corporation.

5

FEATURES AND DESIGN

This Multimedia Projector is designed with the most advanced technology for portability, durability, and ease of use. The projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD) technology.

Compatibility

This projector widely accepts various video and computer input signals including;

●Computers

IBM-compatible and Macintosh computers up to 1280 x 1024 resolution.

●6 Color Systems

NTSC, PAL, SECAM, NTSC 4.43, PAL-M or PAL- N color system can be connected.

●S-Video

S-Video signals, such as a S-VHS VCR output signals, can be connected.

High Resolution Image

This projector provides 1024 x 768 dots resolution for computer input and 800 horizontal TV lines. The resolution from the computer between 1024 x 768 and 1280 x 1024 is compressed into 1024 x 768 dots. This projector cannot display image of over 1280 x 1024 dots. When the resolution of your computer is over than 1280 x 1024, reset the computer output for lower resolution.

Power Management

Power Management function is provided to reduce power consumption while the projector is not in use.

This Power Management function operates to turn the Projection Lamp off when the projector detects signal interruption and any button is not pressed over 5 minutes. The Projection Lamp is automatically turned on again when the projector detects the signal or any operation button is pressed.

This projector is shipped with this function ON.

Laser Pointer Function

The Wireless Remote Control Unit supplied with this projector includes the Laser Pointer function. This function helps you to make a smart presentation on a projected screen.

Wireless Mouse

The Wireless Remote Control Unit supplied with this projector has Wireless Mouse function for the connected computer. This function enables you to operate both projector and computer with this Wireless Remote Control Unit only.

Multi-Scan System
			Accessories

This projector has Multi-Scan System to conform to almost all computer output signals quickly. There is no need for troublesome manual adjustment of frequency and other settings.

One-Touch Auto Imaging

Incoming computer video signals are recognized and the best setting is automatically selected by the Auto Image adjustment. No complicated setup is necessary and projection is always precise.

Multilanguage Menu Display

Operation menu is displayed in; English, Deutsch, Français, Italiano, Español, or Japanese.

Digital Zoom (Computer Mode only)

The Digital Zoom magnifies the image up to 16 times, allowing you to focus on crucial information at a presentation.

The projector comes with the parts listed below. Check to find all the parts are included. If any parts are missing, contact an authorized dealer or service station.

●Owner's Manual.

●AC Power Cord.

●Wireless Remote Control Unit.

●Wireless/Wired Remote Control Unit.

●Remote Control Cable.

●Batteries for Remote Control Units.

●VGA Cable.

●Mouse Cable for PS/2 port.

●Mouse Cable for serial port.

●Mouse Cable for ADB port.

●VGA/MAC Adapter.

●Protective Dust Cover

●Lens Cover.

Motor-driven Lens Shift

The projection lens can be moved up and down with the motor-driven lens shift function. This function makes it easy to provide the projected image where you want.

The zoom and focus can be also adjusted with motordriven operation.

6

PREPARATION

NAME OF EACH PART OF THE PROJECTOR

FRONT OF THE PROJECTOR

INFRARED

REMOTE RECEIVER

PROJECTION LENS

REMOVABLE

LENS COVER

SPEAKERS

REAR OF THE PROJECTOR

EXHAUST VENT

HOT AIR EXHAUSTED !

Air blown from the exhaust vent is hot. Observe the following when handling your projector or choosing a location to install it.

●Keep heat-sensitive objects away from the exhaust port.

●If you set the projector on top of a metallic surface, the surface will become hot because of the hot air exhaust. Be careful when handling.

●Do not touch the cabinet near to the exhaust vent area, and especially screws and metallic parts. These parts will become hot while the projector is used.

This projector detects the internal temperature and automatically controls the operating power of the Cooling Fans.

INFRARED

REMOTE RECEIVER

AIR INTAKE

VENT

BOTTOM OF THE PROJECTOR

LAMP COVER

CARRYING HANDLE

MAIN ON / OFF

SWITCH

POWER CORD

CONNECTOR

ADJUSTABLE FEET

AIR INTAKE VENT

7

PREPARATION

SETTING-UP THE PROJECTOR

CONNECTING THE AC POWER CORD

This projector uses nominal input voltages of 100-120 V or 200-240 V AC. The projector automatically selects the correct input voltage. It is designed to work with single-phase power systems having a grounded neutral conductor. To reduce the risk of electrical shock, do not plug into any other type of power system.

Consult your authorized dealer or service station if you are not sure of the type of power supply being in use.

Connect the projector with the peripheral equipment before turning the projector on. (Refer to pages 13 ~ 22 for connection.)

Connect the AC Power Cord (supplied) to the projector.

The AC outlet must be near this equipment and must be easily accessible.

NOTE ON THE POWER CORD

The AC Power Cord must meet the requirement of the country where you use the projector. Confirm the AC plug type with the chart below and the proper AC power cord must be used. If the supplied AC Power Cord does not match the AC outlet, contact your sales dealer.

Projector side						AC Outlet side
		For the U.S.A. and Canada				For Continental Europe		For the U.K.
			Ground

To the POWER CORD						To the AC Outlet.
		To the AC Outlet.
CONNECTOR on the						(200 - 240 V AC)
		(120 V AC)		To the AC Outlet.
projector.				(200 - 240 V AC)

8

PREPARATION

POSITIONING THE PROJECTOR

●This projector is basically designed to project on a flat projection surface.

●This projector can be focused from 4.9' (1.5 m) ~ 80.7' (24.6 m).

●Refer to the figure below as an example when positioning the projector to the screen.

THIS PROJECTOR SHOULD BE SET IN THE WAY INDICATED. NEVER HANG

THE PROJECTOR, OR FALL DOWN ON ITS SIDE. IT MAY RESULT IN FIRE

HAZARD.

ROOM LIGHT

Maximum Zoom

600"

Minimum Zoom

The projector should be placed in a room with

400"

limited light. Picture quality will be directly

300"

affected by lightning conditions.

150"

200"

462"

100"

308"

40"

115"

154"

231"

77"

DISTANCE

Screen	Max. Zoom	40"	100"	150"	200"	300"	400"	600"
Size	Min. Zoom		77"	115"	154"	231"	308"	462"
Distance		4.9' (1.5 m)	13.1' (4.0 m)	20' (6.1 m)	26.9' (8.2 m)	40' (12.2 m)	53.8' (16.4 m)	80.7' (24.6 m)

VENTILATION

This projector is equipped with a cooling fan to protect it from overheating. Pay attention to the following to ensure the ventilation and avoid a possible risk of fire and malfunction.

● Do not cover the vents with papers or other materials.

● Keep the rear grill at least 3.3' (1m) away from any object.

● Make sure that there are no objects under the projector. An object under the projector may prevent the projector from taking the cooling air through the bottom vent.

EXHAUST VENT AIR INTAKE VENT (REAR SIDE) (BOTTOM SIDE)

9

PREPARATION

PICTURE LEVEL AND TILT ADJUSTMENT

Picture tilt and projection angle can be adjusted by twisting ADJUSTABLE FEET. Projection angle can be adjusted up to 4 degrees by rotating Adjustable Feet.

DOWN

UP

DOWN

UP

ADJUSTABLE FEET

MOVE THE PROJECTED IMAGE POSITION

Adjust the projected image position (maximum 760mm downward or upward on the 100" screen) by using lens shift function. (See page 33.)

760 mm

100" SCREEN

760 mm

MOVING THE PROJECTOR

Use the carry handle when moving the projector.

Replace the lens cover and rotate the adjustable feet fully clockwise.

CAUTION IN CARRYING OR TRANSPORTING THE PROJECTOR

●Do not drop or bump the projector, otherwise damages or malfunctions may result.

●When carrying the projector, use a suitable carrying case.

●Do not transport the projector by using a courier or transport service in an unsuitable transport case. This may cause damage to the projector. To transport the projector through a courier or transport service, consult your dealer and best case should be applied.

10

CONNECTING THE PROJECTOR

TERMINAL OF THE PROJECTOR

SIDE OF THE PROJECTOR (CONNECT THE COMPUTER)

	9	8	6	5	1			2
10	USB 1 CONTROL PORT 1			AUDIO 1	ANALOG			DIGITAL
				R L (MONO)
11	USB 2 CONTROL PORT 2			AUDIO 2		G	B	H	V
				R
				(MONO)

	R/C JACK SERIAL PORT	AUDIO OUT		ANALOG RGB
		R	L

COMPUTER OUT COMPUTER IN-2 COMPUTER IN-1

3

4

1

2

3

4

5

13 12 7

		8	CONNECTOR
			cable to the projector.
	COMPUTER INPUT-1 TERMINAL (DIGITAL MDR 20-PIN)	9	CONTROL PORT-2 CONNECTOR
	Used to connect a computer to the projector.		Used to connect a mouse cable to the projector.
	COMPUTER INPUT-2 JACKS (BNC TYPE x 5)	10	USB PORT-1 CONNECTOR
	Used to connect a computer to the projector.		Used to connect a computer to the projector.
	MONITOR OUTPUT TERMINAL (ANALOG HDB 15-PIN)	11	USB PORT-2 CONNECTOR
	Used to connect a monitor to the projector.		Used to connect a computer to the projector.
	COMPUTER AUDIO INPUT-1 JACKS (R and L)	12	SERIAL PORT TERMINAL (DB9)
	Used to connect an audio output from the computer to the		Used to connect a computer to the projector.
	projector.	13	WIRED REMOTE JACK
	COMPUTER AUDIO INPUT-2 JACKS (R and L)
			When using the wired remote control, connect the
	Used to connect an audio output from the computer to the		remote cable to this jack.
	projector.

7

Used to connect an audio input from audio equipment to the projector.

11

CONNECTING THE PROJECTOR

SIDE OF THE PROJECTOR (CONNECT THE VIDEO EQUIPMENT)

14

17

20

MONITOR OUT VIDEO IN-2 VIDEO IN-1

15 18

16

VIDEO/Y C/Cb(B-Y) Cr(R-Y)	S-VIDEO							AUDIO
							R	L (MONO)

19

VIDEO/Y C/Cb(B-Y) Cr(R-Y)	S-VIDEO							AUDIO
							R	L (MONO)

22

VIDEO/Y C/Cb(B-Y) Cr(R-Y)

S-VIDEO

AUDIO

R L

14

15 S-VIDEO INPUT JACK-1

Used to connect a S-VHS video source to the projector.

16 AUDIO INPUT JACKS-1 (R and L)

Used to connect an audio source to the projector.

17 VIDEO INPUT JACKS-2 (BNC TYPE x 3)

Used to connect a video source to the projector.

18 S-VIDEO INPUT JACK-2

Used to connect a S-VHS video source to the projector.

21

19

	projector.
20	VIDEO MONITOR OUTPUT JACKS (BNC TYPE x 3)
	Permits video connection to a monitor.
21	VIDEO MONITOR (S-VIDEO) OUTPUT JACK
	Permits S-VHS video connection to a monitor.
22	AUDIO MONITOR OUTPUT JACKS (R and L)
	Permits audio connection to a monitor.

12

CONNECTING THE PROJECTOR

CONNECTING THE COMPUTER

CONNECTING TO THE COMPUTER INPUT 1 TERMINAL (ANALOG HDB 15-PIN)

Personal computers can be connected to the HDB15-pin (VGA) terminal on the projector.

● Connect the computer to these terminals using the VGA cable and VGA/MAC adapter (provided).

CAUTION: For projectors, the VGA cable provided is designed to reduce RFI (Radio Frequency Interference) emissions. For regulatory compliance reasons, this cable must be used and must not be replaced by any other cable.

CONNECTING TO THE COMPUTER INPUT 1 TERMINAL (DIGITAL MDR 20-PIN)

Digital output signal from the computer can be connected to the DIGITAL terminal (MDR 20-pin). When using this input, Graphic Accelerator Board designed for this projector should be installed into your computer and set-up the computer configuration following instruction included in the Graphic Accelerator Board package. Refer to DIGITAL INPUT CONNECTION on page 16 and 18.

CONNECTING TO THE COMPUTER INPUT 2 JACKS (BNC x 5)

Personal computers can be connected to the computer input (Red, Green, Blue, Horiz. Sync. and Vert. Sync.) on the projector.

● Connect the computer to these jacks using the BNC cables (not provided).

CONNECTING TO THE COMPUTER AUDIO INPUT JACKS (1 and 2)

● Connect audio outputs from your computer to these jacks using the audio cable (not provided).

CONNECTING TO THE MULTI-POLE 12-PIN (CONTROL PORT) CONNECTORS (1 and 2)

●When the computer is operated by projector's remote control unit, connect three different type of cables (provided) between projector control port and computer mouse port or serial port.

COMPUTER TYPE	CABLE
IBM Compatible computer with PS/2 mouse port.	Mouse Cable for PS/2 port.
IBM Compatible computer with serial port.	Mouse Cable for Serial port.
Apple Macintosh computer with ADB mouse port.	Mouse Cable for ADB port.

■ CONTROL PORT					PS/2 Port	Serial Port	ADB Port
	2	1		1	––––––––	T x D	––––––––
5				2	CLK	––––––––	ADB
		4		3	DATA	––––––––	––––––––
6			3
				4	––––––––	––––––––	––––––––
				5	––––––––	––––––––	––––––––
				6	––––––––	––––––––	––––––––
				7	––––––––	READY	––––––––
				8	––––––––	––––––––	––––––––
10			7	9	GND	GND	GND
		8		10	––––––––	––––––––	––––––––
9
	12			11	––––––––	––––––––	––––––––
		11		12	––––––––	––––––––	––––––––

CONTROL PORT CABLE REMOVAL HINT

Disconnect control port cable with following steps.

1.	Hold the portion (A)
	of the connector
									B
	with one hand.
2.	Pull the portion (B)

A

arrow direction and remove connector.

13

CONNECTING THE PROJECTOR

CONNECTING TO THE MONITOR OUTPUT TERMINAL (ANALOG HDB 15-PIN)

This terminal output the information of the selected computer source being viewed on the screen (Computer 1 or Computer 2). When video source ("Video 1" or "Video 2") is selected, this terminal outputs Computer 1 input information.

An external monitor can be connected to the HDB15-pin (VGA) terminal on the projector.

● Connect the monitor to this terminal using the VGA cable (not provided).

	5	4	3	2	1
HDB 15-PIN	10	9	8	7	6
TERMINAL
	15 14 13 12 11

Pin No./Signal		Pin No./Signal
1	Red input	9	Non Connect
2	Green input	10	Ground (Vert. sync.)
3	Blue input	11	Sense 0
4	Sense 2	12	Sense 1
5	Ground (Horiz.sync.)	13	Horiz. sync
6	Ground (Red)	14	Vert. sync
7	Ground (Green)	15	Reserved
8	Ground (Blue)

CONNECTING TO THE AUDIO MONITOR OUTPUT (VARIABLE) JACKS

These jacks will contain the audio information of the selected program source being viewed on the screen (Computer 1, Computer 2, Video 1 or Video 2). If you have selected program source Computer 2 the audio signal connected to the Computer 2 audio input jack will be available at the audio monitor output jacks.

Use RCA type audio for connection.

●If the audio input of the audio equipment is stereo, be sure to connect the right and left channels to the respective right and left jacks.

●If the audio input of the audio equipment is monaural, connect it to the left jack.

CONNECTING TO THE SERIAL PORT (DB 9-PIN) TERMINAL

●If you control the projector by computer, you must connect a cable (not provided) from your computer to this terminal.

■ SERIAL PORT

DB9-PIN
TERMINAL
5	4		3	2	1
	9	8	7		6

1	––––––––
2	R x D
3	T x D
4	––––––––
5	Ground
6	––––––––
7	––––––––
8	––––––––
9	––––––––

CONNECTING TO THE USB PORT CONNECTORS (1 and 2)

This port is used to control the projector with the computer. It is also used to control the computer with the Remote control of this projector. (Refer to P49, 50.)

Connect the USB port of the computer to this port.

■ USB PORT

	2		1			1	Vcc
	3		4			2	- Data
						3	+ Data
						4	Ground

14

CONNECTING THE PROJECTOR

CONNECTING AN IBM-COMPATIBLE DESKTOP COMPUTER

MONITOR CABLE

(NOT PROVIDED)

COMPUTER

COMPUTER	BNC CABLE x 5
	(NOT PROVIDED)
OUTPUT
(BNC TYPE x 5)

				VGA CABLE
		COMPUTER OUTPUT		(PROVIDED)
		(HDB15-PIN TYPE)
			AUDIO CABLE
			(NOT PROVIDED)
SERIAL PORT	PS/2 PORT	COMPUTER	R
		AUDIO OUTPUT	L
INPUT	INPUT
					COMPUTER
		COMPUTER			INPUT 1
					(ANALOG)
		AUDIO INPUT 1 or 2 R		L

USB 1

CONTROL PORT 1

AUDIO 1

ANALOG

DIGITAL

IN-1

R

(MONO)

COMPUTER

MOUSE CABLE FOR

USB 2

CONTROL PORT 2

AUDIO 2

R

G

B

H

V

IN-2

COMPUTER

COMPUTER

PS/2 PORT

(MONO)

INPUT 2

(PROVIDED)

R/C JACK

SERIAL PORT

AUDIO OUT

ANALOG RGB

OUT

MONITOR

R

L

COMPUTER

MOUSE CABLE FOR

CONTROL PORT

OUTPUT

OUTPUT 1 or 2

SERIAL PORT

(PROVIDED)

SERIAL

SERIAL PORT CABLE

PORT

(NOT PROVIDED)

OUTPUT

AUDIO CABLE

COMPUTER

AUDIO OUTPUT

(NOT PROVIDED)

AUDIO

SPEAKER

INPUT

OUT

L

R

L

Speaker (L)

Speaker (R)

Amp.

R

NOTE: When connecting the cable, the power cords of both the projector and the external equipment should be disconnected from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on.

15

CONNECTING THE PROJECTOR

CONNECTING AN IBM-COMPATIBLE DESKTOP COMPUTER

(DIGITAL INPUT CONNECTION)

NOTE: This connection need optionally sold Graphic Accelerator Board. For this information, contact to your authorized dealer.

Before using with digital connection, install (Plug in) Graphic Accelerator

Board into PCI bus slot of the computer and set up the computer

COMPUTER		following instructions in the Graphic Accelerator Board package.
				MONITOR CABLE
				(NOT PROVIDED)
		GRAPHIC		ANALOG
		ACCELERATOR				DIGITAL FLAT
		BOARD		OUTPUT
						PANEL CABLE
				DIGITAL		(NOT PROVIDED)
		INSTALL (PLUG)		OUTPUT
		INTO PCI BUS SLOT
SERIAL PORT	PS/2 PORT	COMPUTER	R		AUDIO CABLE
		AUDIO OUTPUT	L		(NOT PROVIDED)
INPUT	INPUT
						COMPUTER
			COMPUTER			INPUT 1
			AUDIO INPUT 1 R		L	(DIGITAL)

		USB 1	CONTROL PORT 1	AUDIO 1			ANALOG		DIGITAL		IN-1
				R		(MONO)					COMPUTER
MOUSE CABLE FOR		USB 2	CONTROL PORT 2	AUDIO 2		R	G	B	H	V	IN-2
PS/2 PORT				R	L	(MONO)					COMPUTER
(PROVIDED)
		R/C JACK	SERIAL PORT	AUDIO OUT				ANALOG RGB			OUT
				R	L
											COMPUTER
MOUSE CABLE FOR	CONTROL PORT
SERIAL PORT	OUTPUT 1
(PROVIDED)
SERIAL PORT CABLE		SERIAL
		PORT
(NOT PROVIDED)		OUTPUT
					COMPUTER
	AUDIO CABLE				AUDIO OUTPUT
	(NOT PROVIDED)

AUDIO

INPUT		SPEAKER
L	R	OUT
			Speaker (L)	Speaker (R)
		L

R

Amp.

NOTE: When connecting the cable, the power cords of both the projector and the external equipment should be disconnected from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on.

16

CONNECTING THE PROJECTOR

CONNECTING AN IBM-COMPATIBLE LAPTOP COMPUTER

COMPUTER

						VGA CABLE
		COMPUTER OUTPUT				(PROVIDED)
		(DB15-PIN TYPE)
			R	AUDIO CABLE
		COMPUTER		(NOT PROVIDED)
SERIAL PORT	PS/2 PORT
		AUDIO OUTPUT
INPUT	INPUT
			L
			COMPUTER				COMPUTER
							INPUT 1
			AUDIO INPUT 1	R		L
							(ANALOG)
			USB 1	CONTROL PORT 1		ANALOG	DIGITAL
					R	(MONO)
	MOUSE CABLE FOR
	PS/2 PORT
	(PROVIDED)		USB 2	CONTROL PORT 2 AUDIO 2
							B H V
					R	R G
						L (MONO)
		CONTROL PORT
		OUTPUT 1	R/C JACK	SERIAL PORT	AUDIO OUT		ANALOG RGB
					R	L
MOUSE CABLE FOR
SERIAL PORT
(PROVIDED)			SERIAL
						COMPUTER
			PORT
SERIAL PORT CABLE						AUDIO OUTPUT
			OUTPUT
(NOT PROVIDED)

AUDIO CABLE (NOT PROVIDED)

SPEAKER

OUT

R				L	Speaker (L)	Speaker (R)

L

AUDIO

INPUT

R

Amp.

COMPUTER OUT COMPUTER IN-2 COMPUTER IN-1

NOTE: When connecting the cable, the power cords of both the projector and the external equipment should be disconnected from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on.

17