Samsung 793SG, 591SG, 788DF Plus, 594MG User Manual

0 (0)

 

 

 

Install driver

Install programs

SyncMaster 591S/591SG/591V/594MG/592V/ 794V/793DF/793MG/793SG/793V/ 794MG/793S/783DF/788DF Plus

Notational

Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment.

Prohibited

Important to read and understand at all times

Do not disassemble

Disconnect the plug from the outlet

Do not touch

Ground to prevent an electric shock

 

 

Power

When not used for extended periods of time, set your computer to a screen saver.

zIf the same image is present for long periods of time, Phosphor Burnt can be occured, or the screen may be blurred.

zThe images here are for reference only, and are not applicable in all cases (or

countries).

Do not use a damaged or loose plug.

z This may cause electric shock or fire.

Do not pull the plug out by the wire nor touch the plug with wet hands.

z This may cause electric shock or fire.

Use only a properly grounded plug and receptacle.

zAn improper ground may cause electric shock or equipment damage. (Class l Equipment only.)

Insert the power plug firmly so that it does not come loose.

z A bad connection may cause fire.

Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage.

z This may cause electric shock or fire.

Do not connect too many extension cords or plugs to one outlet.

z This may cause fire.

Do not disconnect the power cord while using the monitor.

z A surge may be caused by the separation and may damage the monitor.

Do not use the power cord when the connector or plug is dusty.

zIf the connector or plug of the power cord is dusty, clean it with a dry cloth.

zUsing the power cord with a dusty plug or connector may cause an electric shock or fire.

To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains plug shall be readily operable.

z This may cause an electric shock or fire.

Installation

Be sure to contact an authorized Service Center when installing your monitor in a location with heavy dust, high or low temperatures, high humidity, and exposed to chemical substances and where it operates for 24 hours such as at airports, train stations etc.

Failure to do so may cause serious damage to your set.

Put your monitor in a location with low humidity and a minimum of dust.

z Failure to do so may cause electric shock or fire inside the monitor.

Do not drop the monitor when moving it.

z This may cause damage to the product or the person carrying it.

Install the monitor base in a showcase or shelf so that the end of the base does not protrude from the showcase or shelf.

zDropping the product may cause damage to the product or the person carrying it.

Do not place the product on an unstable or small surface area.

zPlace the product on an even end stable surface ,as the product may fall and cause harm to someone walking by, specifically children.

Do not place the product on the floor.

z Take care, as someone, specifically children may trip over it.

TO PREVENT THE SPREAD OF FIRE, KEEP CANDLES OR OTHER OPEN FLAMES AWAY FROM THIS PRODUCT AT ALL TIMES.

z Otherwise, this may cause fire.

Keep any heating devices away from the power cable.

z A melted coating may lead to electric shock or fire.

Do not install the product in places with poor ventilation, for instance, a bookshelf, closet, etc.

z Any increase in internal temperature may cause fire.

Set down the monitor carefully.

z The monitor could be damaged or broken.

Do not place the monitor face down.

z The CDT surface may be damaged.

Do not use the monitor without the monitor stand.

zIt could break down or cause fire due to bad ventilation.

zIf the monitor must be used without the supplied stand, take steps to insure proper ventilation.

When installing the product, make sure to keep it away from the wall (more than 10 cm/4 inches) for ventilation purposes.

zPoor ventilation may cause an increase in the internal temperature of the product, resulting in a shortened component life and degraded performance.

Keep the plastic packaging (bag) out of children’s reach.

zThe plastic packaging (bag) may cause suffocation if children play with it.

Clean

When cleaning the monitor case or the surface of the CDT, wipe with a slightly

moistened, soft fabric.

Do not clean Flat monitor with water. Use a water-diluted mild detergent.

(Some detergents contain significant amounts of alcohol-based solvents, which can damage (color change) or crack the monitor case. The antiglare/anti-static surface coating on the CDT may also be affected.)

Dilute the detergent (1:10 ratio) with water before using.

Do not spray water or detergent directly onto the monitor.

z This may cause damage, electric shock or fire.

Use the recommended detergent with a smooth cloth.

zYou may prevent the coated CDT from being damaged or the monitor cabinet from being dissolved, cracked or discolored.

zYou may buy a recommended detergent at any Service Center.

If the connector between the plug and the pin is dusty or dirty, clean it properly using a dry cloth.

z A dirty connector may cause electric shock or fire.

Make sure to unplug the power cord before cleaning the product.

z Otherwise, this may cause electric shock or fire.

Unplug the power cord from the power outlet and wipe the product using a soft, dry cloth.

zDo not use any chemicals such as wax, benzene, alcohol, thinners, insecticide, air freshener, lubricant or detergent.

Contact a Service Center or Customer Center for interior cleaning once a year.

zKeep the product's interior clean. Dust which has accumulated in the interior over an extended period of time may cause malfunction or fire.

Others

Do not remove cover(or back).

zThis may cause electric shock or fire.

zRefer to a qualified servicing company.

If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized dealer or the Service Center.

z This may cause electric shock or fire.

Keep the product away from places exposed to oil, smoke or moisture; do not install inside a vehicle.

zThis may cause malfunction, an electric shock or fire.

zEspecially avoid operating the monitor near water or outdoors where the monitor could be exposed to snow or rain.

If the monitor is dropped or the casing is damaged, turn the monitor off and unplug the power cord. Then contact a Service Center.

z The monitor may cause a malfunction, electric shock or fire.

Disconnect the plug from the outlet during storms or lightning or if it is not used for a long period of time.

z Failure to do so may cause electric shock or fire.

Do not try to move the monitor by pulling only the wire or the signal cable.

zThis may cause a breakdown, electric shock or fire due to damage to the cable.

Do not move the monitor right or left by pulling only the wire or the signal cable.

zThis may cause a breakdown, electric shock or fire due to damage to the cable.

Do not cover the vents on the monitor cabinet.

z Bad ventilation may cause a breakdown or fire.

Do not place water containers, chemical products or small metal objects on the monitor.

z This may cause malfunction, an electric shock or fire.

zIf a foreign substance enters the monitor, unplug the power cord and contact the Service Center .

Do not place any heavy objects on the monitor.

z This may cause electric shock or fire.

Keep the product away from combustible chemical sprays or inflammable substances.

z This may cause an explosion or fire.

Never insert anything metallic into the monitor openings.

z This may cause electric shock, fire or injury.

Keep the monitor away from any magnetic substances.

z This may cause discoloring or distortion of the image.

Viewing the monitor continuously at a too close angle may result in damage to your eyesight.

To ease eye strain, take at least a five-minute break after every hour of using the monitor.

Do not install the product on an unstable, uneven surface or a location prone to vibrations.

zDropping the product may cause damage to the product or the person carrying it. Using the product in a location prone to vibrations may shorten the lifetime of the product or may catch fire.

When moving the monitor, turn off and unplug the power cord. Make sure that all cables, including the antenna cable and cables connected to other devices, are disconnected before moving the monitor.

zFailure to disconnect a cable may damage it and lead to fire or an electric shock.

Place the product out of children’s reach, as they could damage by hanging onto it.

z A falling product may cause injury to the person or even fatality.

When not using the product for an extended time period, keep the product unplugged

zOtherwise, this may cause heat emission from the accumulated dirt or degraded insulation, causing electric shock or fire.

Do not place children's favorite objects (or anything else that may be tempting) on the product.

zChildren may try to climb on the product to retrieve an object. The product could fall, causing physical damage or even death.

Good Postures When Using the Monitor

Try to maintain a good posture when using the monitor.

zKeep your back straight.

zKeep a distance of about 45 ~ 50 cm between your eyes and the monitor screen. Look at the screen from slightly above it, and have the monitor directly in front of you.

zTilt the monitor upwards by 10 ~20 degrees. Adjust the monitor height so that the top of the monitor is slightly below eye level.

zAdjust the monitor angle so that there is no reflected light on the screen.Try to maintain your arms perpendicular to your armpits.

zKeep your arms level with the back of your hands.

zKeep the angle of the elbow perpendicular.

zKeep the angle of the knees at more than 90 degree. Do not let your feet fall up from the floor. Adjust the arm position so that it is below the heart.

SyncMaster 591S/591SG/591V/594MG/793DF/793MG 793SG/793V/794MG/793S/783DF

Please make sure the following items are included with your monitor.

If any items are missing, contact your dealer.

Contact a local dealer to buy optional items.

Unpacking

Monitor and Stand

(Some models include a stand attached.)

Manual

 

Warranty Card

User's Guide,

 

Monitor Driver,

Quick Setup Guide

(Not available in all

Natural Color software,

 

locations)

 

MagicTune™ software

 

 

Cable

Power Cord

Stand

Stand

For Multimedia model (Option)

Manual

User Guide

Cable

Sound Cables(2each)

DC Power Cord

Stand

Multimedia Speaker Stand

Front

Menu button [MENU] Opens the OSD menu. Also used to exit the OSD menu or return to the previous menu.

Adjust buttons [] These buttons allow you to highlight and adjust items in the menu.

Enter button [] Power button [] Power indicator

Used to select the OSD menu.

Use this button for turn the monitor on and off.

This light glows green during normal operation, and blinks green once as the monitor saves your adjustments.

See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.

Rear

(The configuration at the back of the monitor may vary from product to product.)

Power port

Connect the power cord for your monitor to the power port on

 

the back of the monitor.

Signal Cable

Connect the signal cable to the video port on your computer

 

(video board, video card, or graphics card).

See Connecting the Monitor for further information regarding cable connections.

Bottom

Tilt/Swivel Base

You can separate the base from the monitor.

SyncMaster 592V/794V/788DF Plus

Please make sure the following items are included with your monitor.

If any items are missing, contact your dealer.

Contact a local dealer to buy optional items.

Unpacking

Monitor and Stand

(Some models include a stand attached.)

Manual

 

Warranty Card

User's Guide,

 

Monitor Driver,

Quick Setup Guide

(Not available in all

Natural Color software,

 

locations)

 

MagicTune™ software

 

 

Cable

Power Cord

Stand

Stand

For Multimedia model (Option)

Manual

User Guide

Cable

Sound Cables(2each)

DC Power Cord

Stand

Multimedia Speaker Stand

Front

Menu button [MENU] Opens the OSD menu. Also used to exit the OSD menu or return to the previous menu.

Adjust buttons [] These buttons allow you to highlight and adjust items in the menu.

Enter button [] Power button [] Power indicator

Used to select the OSD menu.

Use this button for turn the monitor on and off.

This light glows green during normal operation, and blinks green once as the monitor saves your adjustments.

See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.

Rear

(The configuration at the back of the monitor may vary from product to product.)

Power port

Connect the power cord for your monitor to the power port on

 

the back of the monitor.

Signal Cable

Connect the signal cable to the video port on your computer

 

(video board, video card, or graphics card).

See Connecting the Monitor for further information regarding cable connections.

Bottom

Tilt/Swivel Base

You can separate the base from the monitor.

Connecting the Monitor

Setup-For Multimedia model | Multimedia Speaker Stand

1.Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet.

2.Use a connection appropriate for your computer.

2-1. Connecting to a computer

Connect the signal cable to the 15-pin, D-sub connector on the back of your computer.

2-2. Connecting to a new Macintosh

Connect the monitor to the Macintosh computer using the D-SUB connection cable.

Turn on your computer and monitor. If your monitor displays an image, installation is complete.

Setup-For Multimedia model

1.Turn off your computer and unplug the power cord.

2.Connect the end of the signal cable to your computer's video port(video board, video card or graphics card).

3.Connect one end of the other sound cable to the Mic Input jack on your sound card or computer.Connect the other end of this cable to the Mic By-pass jack on the back of the monitor stand.

4.Plug the DC power cord from the stand into a nearby outlet.

5.Connect the power cord for your monitor to the power port on the back of the monitor.

6.Plug the power cord for the monitor and the power cord for your computer into a nearby outlet.

7.Turn on your computer and monitor.

8.Turn up or down the On-Off control terminal on the stand of the monitor until it clicks.

9.Execute a sound program, music or sound effect in your computer and then adjust the volume by turning up or down until the sound volume is appropriate.

10.Adjust the treble and bass.

Sound distortion may occur when the monitor is placed on top of a mostly hollow cabinet such as your computer. If this occurs, place a pad or magazine beneath the monitor stand. High sound volume may also cause sound distortion; lower the volume.

Multimedia Speaker Stand

1.Mic By-pass Jack

To transmit your voice,connect a sound cable from the Mic By-pass jack to the mic in jack on the sound card slot in your computer.

2.Stereo Input Jack

Connect a sound cable from the input source(sound card,computer,CD-ROM drive).

3.DC Power Cord

Connect DC power cord to monitor DC 12V output jack.

4.Power Indicator

Glows green when the speakers are turned on.

5.On/Off Volume

Turns On/Off and adjusts the output volume.

6.Treble Control

Use to control high frequencies.

7.Bass Control

Use to control low frequencies.

8.Mic Input Jack

To transmit your voice,connect a microphone to this jack.

9.Headphone Jack

To listen in privacy,connect headphones here.

10.

Detachable Stand Top

Base Installation

Tilt/Swivel Base | Attaching and Removing the Base

Tilt/Swivel Base

With the built-in pedestal, you can tilt and/or swivel the monitor for the most comfortable viewing angle.

The base is detachable.

Attaching and Removing the Base

If your monitor was supplied with the base detached, attach the base as follows.

Remove the twist-tie before attaching the base to the monitor.

Attaching the Base

1.Place the monitor upside-down on a flat work surface.

2.Align the tabs on the base with the corresponding slots on the bottom of the monitor.

3.Press the base onto the monitor until the tabs are fully engaged in the slots.

4.Push the base toward the front of the monitor until the release latch clicks into the locked position.

*Do not bend the snap.

Removing the Base

5.Squeeze and pull up on the release latch on the base.

6.Push the base toward the back of the monitor and lift up to remove the base.

The base will align with the monitor slots in only one position.

Installing the Monitor Driver(Automatic)

When prompted by the operating system for the monitor driver, insert the CD-ROM

included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have.

Prepare a blank disk and download the driver program file at the Internet web site shown here.

z Internet web site : http://www.samsung.com/ (Worldwide) http://www.samsung.com/monitor (U.S.A) http://www.sec.co.kr/monitor (Korea) http://www.samsungmonitor.com.cn/ (China)

1.Insert the CD into the CD-ROM drive.

2.Click "Windows"

3.Choose your monitor model in the model list, then click the "OK".

4.If you can see following message window, then click the "Continue Anyway" button. Then click "OK". (Microsoft® Windows® XP/2000 Operating System)

This monitor driver is under certified MS logo and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage.

http://www.samsung.com/.

5. Monitor driver installation is completed.

Installing the Monitor Driver(Manual)

Windows XP | Windows 2000 | Windows Me | Windows NT | Linux

When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating

system to another. Follow the directions appropriate for the operating system you have.

Prepare a blank disk and download the driver program file at the Internet web site shown here.

z Internet web site : http://www.samsung.com/ (Worldwide) http://www.samsung.com/monitor (U.S.A) http://www.sec.co.kr/monitor (Korea) http://www.samsungmonitor.com.cn/ (China)

Microsoft® Windows® XP Operating System

1.Insert CD into the CD-ROM driver.

2.Click "Start" —> "Control Panel" then click the "Appearance and Themes" icon.

3. Click "Display" icon and choose the "Settings" tab then click "Advanced..".

4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab.

5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button.

Samsung 793SG, 591SG, 788DF Plus, 594MG User Manual

6. Select "Don't search ,I will.." then click "Next" and then click "Have disk".

7.Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button.

8.If you can see following message window, then click the "Continue Anyway" button. Then click "OK" button.

This monitor driver is under certified MS logo and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage.

http://www.samsung.com/.

9. Click the "Close" button, then click "OK" button continually.

10. Monitor driver installation is completed.

Microsoft® Windows® 2000 Operating System

When you can see "Digital Signature Not Found" on your monitor, follow these steps.

1.Choose "OK" button on the "Insert disk" window.

2.Click the "Browse" button on the "File Needed" window.

3.Choose A:(D:\Driver) then click the "Open" button and then click "OK" button.

How to install

1.Click "Start" , "Setting" , "Control Panel".

2.Double click the "Display" Icon.

3.Choose the "Settings" tab and then click "Advanced..".

4.Choose "Monitor".

Case1: If the "Properties" button is inactive, it means your monitor is properly configured. Please stop installation

Case2: If the "Properties" button is active, click the "Properties" button then follow next steps continually.

5.Click "Driver" and then click on "Update Driver.." then click on the "Next" button.

6.Choose "Display a list of the known drivers for this device so that I can choose a specific driver" then click "Next" and then click "Have disk".

7.Click the "Browse" button then choose A:(D:\Driver).

8.Click the "Open" button, then click "OK" button.

9.Choose your monitor model and click the "Next" button then click "Next" button.

10.Click the "Finish" button then the "Close" button.

If you can see the "Digital Signature Not Found" window then click the "Yes"button. And click the "Finish" button then the "Close" button.

Microsoft® Windows® Millennium Operating System

1.Click "Start" , "Setting" , "Control Panel".

2.Double click "Display" icon.

3.Select the "Settings" tab and click "Advanced Properties" button.

4.Select the "Monitor" tab.

5.Click the "Change" button in the "Monitor Type" area.

6.Choose "Specify the location of the driver".

7.Choose "Display a list of all the driver in a specific location.." then click "Next" button.

8.Click the "Have Disk" button

9.Specify A:\(D:\driver) then click "OK" button.

10.Select "Show all devices" and choose the monitor that corresponds to the one you connected to your computer and click "OK".

11.Continue choosing "Close" button and "OK" button until you close the Display Properties dialogue box.

Loading...
+ 57 hidden pages