Loading...
SyncMaster 710TM / 910TM / 713BM / 913TM
Notational
Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment.
Prohibited |
Important to read and understand at all times |
Do not disassemble |
Disconnect the plug from the outlet |
Do not touch |
Grounding to prevent an electric shock |
|
|
Power
When not used for extended period of time, set your computer to DPMS.
If using a screen saver, set it to the active screen mode.
Do not use a damaged or loose plug.
z This may cause an electric shock or fire.
Do not pull the plug out by the wire nor touch the plug with wet hands.
z This may cause an electric shock or fire.
Use only a properly grounded plug and receptacle.
z An improper ground may cause electric shock or equipment damage.
Insert the power plug firmly so that it does not come loose.
z A bad connection may cause fire.
Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage.
z This may cause an electric shock or fire.
Do not connect too many extension cords or plugs to an outlet.
z This may cause fire.
Installation
Be sure to contact an authorized Service Center when installing your set in a location with heavy dust, high or low temperatures, high humidity, and chemical substances, or where it will be operated for 24 hours continuously such as an airport, train station or etc.
Failure to do so may cause serious damage to your set.
Put your monitor in a location with low humidity and a minimum of dust.
z Failure to do so may cause an electric shock or fire inside the monitor.
Do not drop the monitor when moving it.
z This may cause damage to the product or human body.
Install the monitor base in a showcase or shelf so that the end of the base does not project beyond the showcase or shelf.
zDropping the product may cause damage to the product or personal injury.
Do not place the product on an unstable or small surface area.
zPlace the product on an even, stable surface, as the product may fall and cause harm to someone walking by, specifically children.
Do not place the product on the floor.
z Someone, specifically children could trip over it.
Keep any flammable objects such as candles, insecticides or cigarettes away from the product.
z Otherwise, this may cause a fire.
Keep any heating devices away from the power cable.
z A melted coating may lead to electric shock or fire.
Do not install the product in places with poor ventilation, for instance, a bookshelf, closet, etc.
z Any increase in internal temperature may cause fire.
Set down the monitor carefully.
z The monitor could be damaged or broken.
Do not place the monitor face down.
z The TFT-LCD surface may be damaged.
Installing a wall bracket must be done by a qualified professional.
zInstallation by unqualified personnel may result in injury.
zAlways use the mounting device specified in the owner's manual.
When installing the product, make sure to keep it away from the wall (more than 10cm/4inch ) for ventilation purposes.
zPoor ventilation may cause an increase in the internal temperature of the product, resulting in a shortened component life and degraded performance.
Clean
When cleaning the monitor case or the surface of the TFT-LCD screen, wipe with a slightly moistened, soft fabric.
Do not spray water or detergent directly on the monitor.
z This may cause damage, electric shock or fire.
Use the recommended detergent with a smooth cloth.
If the connector between the plug and the pin is dusty or dirty, clean it properly with a dry cloth.
z A dirty connector may cause an electric shock or fire.
Make sure to unplug the power cord before cleaning the product.
z Otherwise, this may cause electric shock or fire.
Unplug the power cord from the power outlet and wipe the product using a soft, dry cloth.
zDo not use any chemicals such as wax, benzene, alcohol, thinners, insecticide, air freshener, lubricant or detergent.
Contact the Service Center or Customer Center for interior cleaning once a year.
zKeep the product's interior clean. Dust which has accumulated in the interior over an extended period of time may cause malfunction or fire.
Others
Do not remove cover (or back).
zThis may cause an electric shock or fire.
zRefer servicing to qualified service personnel.
If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized dealer or service.
z This may cause an electric shock or fire.
Keep the product away from places exposed to oil, smoke or moisture; do not install inside a vehicle.
zThis may cause malfunction, an electric shock or fire.
zEspecially avoid operating the monitor near water or outdoors where the monitor could be exposed to snow or rain.
If the monitor is dropped or the casing is damaged, turn the monitor off and unplug the power cord. Then contact the Service Center.
z The monitor may malfunction, causing an electric shock or fire.
Disconnect the plug from the outlet during storms or lightening or if it is not used for a long period of time.
z Failure to do so may cause an electric shock or fire.
Do not try to move the monitor by pulling only the wire or the signal cable.
zThis may cause a breakdown, electric shock or fire due to damage to the cable.
Do not move the monitor right or left by pulling only the wire or the signal cable.
zThis may cause a breakdown, electric shock or fire due to damage to the cable.
Do not cover the vents on the monitor cabinet.
z Bad ventilation may cause a breakdown or fire.
Do not place water containers, chemical products or small metal objects on the monitor.
zThis may cause malfunction, an electric shock or fire.
zIf a foreign substance enters the monitor, unplug the power cord and contact the Service Center .
Keep the product away from combustible chemical sprays or inflammable substances.
z This may cause an explosion or fire.
Never insert anything metallic into the monitor openings.
z This may cause an electric shock, fire or injury.
Do not insert metal objects such as chopsticks, wire and gimlet or inflammable objects such as paper and match into the vent, headphone port or AV ports.
zIt may cause a fire or an electric shock. If an alien substances or water flows into the product, turn the product off, unplug the power connector from the wall outlet and contact Service Center.
If you view a fixed screen for an extended period of time, residual image or blurriness may appear.
zChange the mode to energy save or set a screensaver to moving picture when you need to be away from the monitor for an extended period of time.
Adjust the resolution and frequency to the levels appropriate for the model.
zInappropriate resolution may cause undesirable picture quality. 17, 19 inch - 1280 X 1024
Keep the volume at a proper level when you use the headphones.
z Excessively loud volume levels may damage hearing.
Watching the monitor continuously at a too close angle may result in eyesight damage.
To ease eye strain, take at least a five-minute break after every hour of using the monitor.
Do not install the product on an unstable, uneven surface or a location prone to vibrations.
zDropping the product may cause damage to the product or personal injury. Using the product in a location prone to vibrations may shorten the lifetime of the product or may catch fire.
When moving the monitor, turn off and unplug the power cord. Make sure that all cables, including the antenna cable and cables connected to other devices, are disconnected before moving the monitor.
zFailure to disconnect a cable may damage it and lead to fire or an electric shock.
Place the product out of children's reach, as they could damage it by hanging onto it.
z A falling product could cause physical damage even death.
When not using the product for an extended time period, keep the product unplugged
zOtherwise, this may cause heat emission from the accumulated dirt or degraded insulation, leading to electric shock or fire.
Do not place children's favorite objects (or anything else that may be tempting) on the product.
zChildren may try to climb on the product to retrieve an object. The product could fall, causing physical damage or even death.
SyncMaster 710TM
Please make sure the following items are included with your monitor.
If any items are missing, contact your dealer.
Contact a local dealer to buy optional items.
Unpacking
Monitor ( Type (A) ) |
Monitor ( Type (B) ) |
|
|
Manual
|
|
User's Guide, |
|
Warranty Card |
Monitor Driver, |
Quick Setup Guide |
(Not available in all |
Natural Color software, |
|
locations) |
MagicTune™ software, |
|
|
MagicRotation software |
Cable
D-Sub Cable |
Power Cord |
Audio Cable |
Sold separately
DVI Cable
Front
Menu button [
] Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu.
MagicBright button MagicBright is a new feature providing optimum viewing
[
] environment depending on the contents of the image you are watching. Currently four different modes are available: Custom, Text, Internet, and Entertain. Each mode has its own preconfigured brightness value. You can easily select one of four settings by simply pressing MagicBright control buttons.
1) Custom
Although the values are carefully chosen by our engineers, the pre-configured values may not be comfortable to your eyes depending on your taste.
If this is the case, adjust the Brightness and Contrast by using the OSD menu.
2) Text : Normal Brightness
For documentations or works involving heavy text.
3) Internet : Medium Brightness
For working with a mixture of images such as text and
graphics.
4) Entertain : High Brightness
|
For watching motion pictures such as a DVD or VCD. |
|
|
>>Click here to see an animation clip |
|
Volume button[ ] |
When OSD is not on the screen, push the button to adjust |
|
volume. |
||
|
||
Adjust buttons [ ] |
Adjust items in the menu. |
|
Enter button [ ] / |
Activates a highlighted menu item. / |
|
Source button |
Push the 'Source' and then select the Video signal while the |
|
|
OSD is off. (When the Source button is pressed to change the |
|
|
input mode, a message appears on the upper left of the screen |
|
|
displaying the current mode -- analog or digital input signal.) |
|
|
Note : If you select the Digital mode, you must connect your |
|
|
monitor to the graphic card's port using the DVI cable. |
Auto button
Power button [
]
Power indicator
Use this button for auto adjustment.
Use this button to turn the monitor on and off.
This light glows green during normal operation, and blinks green once as the monitor saves your adjustments.
See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed or when leaving it unattended for long periods.
Rear
(The configuration at the back of the monitor may vary from product to product.)
Power port |
Connect the power cord to the power port on the back of the monitor. |
DVI port |
Connect the DVI Cable to the DVI Port on the back of your Monitor. |
D-sub 15-pin port |
Connect the signal cable to the 15-pin, D-sub connector on the back |
|
of your monitor. |
Power on/off Switch |
Use this button for turn the monitor on and off. |
Kensington Lock The Kensington lock is a device used to physically fix the system when using it in a public place. (The locking device has to be purchased separately. )
Headphone connection terminal
AUDIO IN Connect the audio cable for your monitor to the audio port on the back of your computer.
See Connecting the Monitor for further information regarding cable connections.
SyncMaster 713BM
Please make sure the following items are included with your monitor.
If any items are missing, contact your dealer.
Contact a local dealer to buy optional items.
Unpacking
Type (A)
Monitor & Simple stand |
Bottom |
Type (B)
Monitor & Pivot stand
Manual
|
|
User's Guide, |
|
Warranty Card |
Monitor Driver, |
Quick Setup Guide |
(Not available in all |
Natural Color software, |
|
locations) |
MagicTune™ software, |
|
|
MagicRotation software |
Cable
D-Sub Cable |
Power Cord |
Audio Cable |
Sold separately
DVI Cable
Front
Menu button [
]
MagicBright button [
]
Volume button[
]
Adjust buttons [
]
Enter button [
] / Source button
Auto button
Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu.
MagicBright is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently four different modes are available: Custom, Text, Internet, and Entertain. Each mode has its own preconfigured brightness value. You can easily select one of four settings by simply pressing MagicBright control buttons.
1) Custom
Although the values are carefully chosen by our engineers, the pre-configured values may not be comfortable to your eyes depending on your taste.
If this is the case, adjust the Brightness and Contrast by using the OSD menu.
2) Text : Normal Brightness
For documentations or works involving heavy text.
3) Internet : Medium Brightness
For working with a mixture of images such as text and graphics.
4) Entertain : High Brightness
For watching motion pictures such as a DVD or VCD. >>Click here to see an animation clip
When OSD is not on the screen, push the button to adjust volume.
Adjust items in the menu.
Activates a highlighted menu item. /
Push the 'Source' and then select the Video signal while the OSD is off. (When the Source button is pressed to change the input mode, a message appears on the upper left of the screen displaying the current mode -- analog or digital input signal.) Note : If you select the Digital mode, you must connect your monitor to the graphic card's port using the DVI cable.
Use this button for auto adjustment.
Power button [ ] |
Use this button to turn the monitor on and off. |
Power indicator |
This light glows green during normal operation, and blinks green |
|
once as the monitor saves your adjustments. |
See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed or when leaving it unattended for long periods.
Rear
(The configuration at the back of the monitor may vary from product to product.)
Power port |
Connect the power cord to the power port on the back of the monitor. |
DVI port |
Connect the DVI Cable to the DVI Port on the back of your Monitor. |
D-sub 15-pin port |
Connect the signal cable to the 15-pin, D-sub connector on the back |
|
of your monitor. |
Power on/off Switch |
Use this button for turn the monitor on and off. |
Kensington Lock |
The Kensington lock is a device used to physically fix the system |
|
when using it in a public place. (The locking device has to be |
|
purchased separately. ) |
Headphone connection terminal
AUDIO IN Connect the audio cable for your monitor to the audio port on the back of your computer.
See Connecting the Monitor for further information regarding cable connections.
SyncMaster 910TM / 913TM
Please make sure the following items are included with your monitor.
If any items are missing, contact your dealer.
Unpacking
Monitor
Manual
|
|
User's Guide, |
|
Warranty Card |
Monitor Driver, |
Quick Setup Guide |
(Not available in all |
Natural Color software, |
|
locations) |
MagicTune™ software, |
|
|
MagicRotataion software |
Cable
D-Sub Cable |
Power Cord |
Audio Cable |
Sold separately
DVI Cable(option)
Front
Menu button [
] Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu.
MagicBright button MagicBright is a new feature providing optimum viewing
[
] environment depending on the contents of the image you are watching. Currently four different modes are available: Custom, Text, Internet, and Entertain. Each mode has its own preconfigured brightness value. You can easily select one of four settings by simply pressing MagicBright control buttons.
1) Custom
Although the values are carefully chosen by our engineers, the pre-configured values may not be comfortable to your eyes depending on your taste.
If this is the case, adjust the Brightness and Contrast by using the OSD menu.
2) Text : Normal Brightness
For documentations or works involving heavy text.
3) Internet : Medium Brightness
For working with a mixture of images such as text and
graphics.
4) Entertain : High Brightness
|
For watching motion pictures such as a DVD or VCD. |
|
|
>>Click here to see an animation clip |
|
Volume button[ ] |
When OSD is not on the screen, push the button to adjust |
|
volume. |
||
|
||
Adjust buttons [ ] |
Adjust items in the menu. |
|
Enter button [ ] / |
Activates a highlighted menu item. / |
|
Source button |
Push the 'Source' and then select the Video signal while the |
|
|
OSD is off. (When the Source button is pressed to change the |
|
|
input mode, a message appears on the upper left of the screen |
|
|
displaying the current mode -- analog or digital input signal.) |
|
|
Note : If you select the Digital mode, you must connect your |
|
|
monitor to the graphic card's port using the DVI cable. |
Auto button
Power button [
]
Power indicator
Use this button for auto adjustment.
Use this button to turn the monitor on and off.
This light glows green during normal operation, and blinks green once as the monitor saves your adjustments.
See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed or when leaving it unattended for long periods.
Rear
(The configuration at the back of the monitor may vary from product to product.)
Power port |
Connect the power cord to the power port on the back of the monitor. |
DVI port |
Connect the DVI Cable to the DVI Port on the back of your Monitor. |
D-sub 15-pin port |
Connect the signal cable to the 15-pin, D-sub connector on the back |
of your monitor.
Power on/off Switch Use this button for turn the monitor on and off.
Kensington Lock The Kensington lock is a device used to physically fix the system when using it in a public place. (The locking device has to be purchased separately. )
Headphone connection Connect your headphone to the Headphone-out port. terminal
AUDIO IN Connect the audio cable for your monitor to the audio port on the back of your computer.
See Connecting the Monitor for further information regarding cable connections.
SyncMaster 710TM
1.Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet.
2-1. Using the D-sub (Analog) connector on the video card.
Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor.
2-2. Using the DVI (Digital) connector on the video card.
Connect the DVI Cable to the DVI Port on the back of your Monitor.
2-3. Connected to a Macintosh.
Connect the monitor to the Macintosh computer using the D-SUB connection cable.
2-4. In the case of an old model Macintosh, you need to connect the monitor using a special Mac adapter.
3.Turn on your computer and monitor. If your monitor displays an image, installation is complete.
Pivot Stand
Attaching a base
This monitor accepts a 100 mm x 100 mm VESA-compliant mounting interface pad.
A.Monitor
B.Mounting interface pad
1.Turn off your monitor and unplug its power cord.
2.Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen.
3.Remove four screws and then remove the Stand from the LCD monitor.
4.Align the Mounting Interface Pad with the holes in the Rear Cover Mounting Pad and secure it with four screws that came with the arm-type base, wall mount hanger or other base.
SyncMaster 713BM
1.Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet.
2-1. Using the D-sub (Analog) connector on the video card.
Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor.
2-2. Using the DVI (Digital) connector on the video card.
Connect the DVI Cable to the DVI Port on the back of your Monitor.
2-3. Connected to a Macintosh.
Connect the monitor to the Macintosh computer using the D-SUB connection cable.
2-4. In the case of an old model Macintosh, you need to connect the monitor using a special Mac adapter.
3.Turn on your computer and monitor. If your monitor displays an image, installation is complete.
Monitor Assembly
Monitor and Bottom
Pivot Stand
Attaching a base
This monitor accepts a 100 mm x 100 mm VESA-compliant mounting interface pad.
Simple stand |
Pivot stand |
A.Monitor
B.Mounting interface pad
1.Turn off your monitor and unplug its power cord.
2.Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen.
3.Remove four screws and then remove the Stand from the LCD monitor.
4.Align the Mounting Interface Pad with the holes in the Rear Cover Mounting Pad and secure it with four screws that came with the arm-type base, wall mount hanger or other base.
SyncMaster 910TM / 913TM
1.Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet.
2-1. Using the D-sub (Analog) connector on the video card.
Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor.
2-2. Using the DVI (Digital) connector on the video card.
Connect the DVI Cable to the DVI Port on the back of your Monitor.
2-3. Connected to a Macintosh.
Connect the monitor to the Macintosh computer using the D-SUB connection cable.
2-4. In the case of an old model Macintosh, you need to connect the monitor using a special Mac adapter.
3.Turn on your computer and monitor. If your monitor displays an image, installation is complete.
Pivot Stand
Attaching a base
This monitor accepts a 100 mm x 100 mm VESA-compliant mounting interface pad.
Loading...