Samsung 460MP, 460MPn, 400MPN, 400MP User Manual

0 (0)

SyncMaster 400MP,460MP,400MPn, 460MPn

LCD Monitor

User Manual

Safety Instructions

Notational

Note

These safety instructions must be followed to ensure your safety and prevent property damage.

Make sure to read the instructions carefully and use the product in the correct manner.

Warning / Caution

Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment.

Notational Conventions

Prohibited

Do not disassemble

Do not touch

Important to read and understand at all times

Disconnect the plug from the outlet

Ground to prevent an electric shock

Power

When not used for extended period of time, set your computer to DPM.

If using screen saver, set it to active screen mode.

The images here are for reference only, and are not applicable in all cases (or countries).

Shortcut to Anti-Afterimage Instructions

Do not use a damaged power cord or plug or a damaged or loose power outlet.

Otherwise, this may result in electric shock or fire.

Do not touch the power plug with wet hands when removing or plugging the plug into the outlet.

Otherwise, this may result in electric shock.

Make sure to connect the power cord to a grounded power outlet.

Otherwise, it may result in electric shock or personal injury.

Ensure that the power plug is plugged into the power outlet firmly and correctly.

Otherwise, this may result in fire.

Safety Instructions

Do not forcefully bend or pull the power plug and do not place any heavy material on it.

Otherwise, this may result in fire.

Do not connect multiple appliances to the same power outlet.

Otherwise, this may cause fire due to overheating.

Do not disconnect the power cord while using the product.

Otherwise, this may result in damage to the product due to electric shock.

To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains plug shall be readily operable.

This may cause electric shock or fire.

Use only the power cord provided by our company. Do not use the provided power cord of another product.

Otherwise, this may result in fire or electric shock.

Installation

Be sure to contact an authorized Service Center when installing your monitor in a location with heavy dust, high or low temperatures, high humidity, and exposed to chemical substances and where it operates for 24 hours such as at airports, train stations etc.

Failure to do so may cause serious damage to your monitor.

Ensure that at least two persons lift and move the product.

Otherwise, it may be dropped and cause personal injury, and/or damage the product.

When installing the product in a cabinet or rack, make sure that the front end of the bottom of the product does not project out.

Otherwise, it may fall or cause personal injury.

Use a cabinet or rack of a size appropriate to the product.

DO NOT PLACE CANDLES, MOSQUITO REPELLANT, CIGA-

RETTES AND ANY HEATING APPLIANCES NEAR THE PROD-

UCT.

Otherwise, this may result in fire.

Keep heating appliances as far away from the power cord or the product as possible.

Otherwise, this may result in electric shock or fire.

Safety Instructions

Do not install it in a badly ventilated location such as a bookcase or closet.

Otherwise, this may result in fire due to an increase in the internal temperature.

When putting the product down, make sure to put it down softly.

Otherwise, this may result in damage to the screen display.

Do not place the front of the product on the floor.

Otherwise, this may result in damage to the screen display.

Ensure that an authorized installation company installs the wall mount.

Otherwise, it may fall and cause personal injury.

Make sure to install the specified wall mount.

Install your product in a well ventilated location. Ensure that there is a clearance of more than 10 cm from the wall.

Otherwise, it may result in fire due to an increase in the internal temperature.

Ensure that the packaging vinyl is kept away from children.

Otherwise, it may result in serious harm (suffocation) if children play with it.

If the height of your monitor is adjustable, do not place any object or part of your body on the stand when lowering it.

This may cause damage to the product or the person carrying it.

Clean

When cleaning the monitor case or the surface of the TFT-LCD screen, wipe with a slightly moistened, soft fabric.

Do not spray cleaner directly onto the surface of the product.

Otherwise, this may result in the discoloration and distortion of the structure and the screen surface may peel off.

Clean the product using a soft cloth with a monitor cleaner only. If you must use a cleaner other than the monitor cleaner, dilute it with water at a ratio of 1:10.

When cleaning the power plug pins or dusting the power outlet, clean it with a dry cloth.

Otherwise, it may result in fire.

Safety Instructions

When cleaning the product, make sure to disconnect the power cord.

Otherwise, it may result in electric shock or fire.

When cleaning the product, disconnect the power cord and clean it softly with a dry cloth.

(Do not use chemicals such as wax, benzene, alcohol, thinner, mosquito repellant, lubricant, or cleaner.) These may change the appearance of the product surface and peel off the indication labels on the product.

Since the product housing is easily scratched, make sure to use the specified cloth only.

Use the specified cloth adding only a little water. As the product may be scratched if there is any foreign material on the cloth, make sure to shake it thoroughly before using it.

When cleaning the product, do not spray water directly onto the main body of the product.

Ensure that water does not enter the product and that it is not wet.

Otherwise, this may result in electric shock, fire or a malfunction.

Others

The product is a high voltage product. Ensure that users do not disassemble, repair or modify the product themselves.

Otherwise, this may result in electric shock or fire. If the product needs to be repaired, contact a Service Center.

If there is a strange smell or a strange sound or smoke is coming from the product, disconnect the power plug immediately and contact a Service Center.

Otherwise, this may result in electric shock or fire.

Do not place this product in a location exposed to moisture, dust, smoke, water, or in a car.

Otherwise, this may result in electric shock or fire.

When you drop the product or the case is broken, turn the power off and disconnect the power cord. Contact a Service Center.

Otherwise, this may result in electric shock or fire.

If thunder or lightening is occurring, do not touch the power cord or antenna cable.

Otherwise, this may result in electric shock or fire.

Safety Instructions

Do not try to move the monitor by pulling only the wire or the signal cable.

Otherwise, it may fall and result in electric shock, damage to the product or fire due to damage to the cable.

Do not lift or move the product back and forwards or right and left while only holding the power cord or signal cables.

Otherwise, it may fall and result in electric shock, damage to the product or fire due to damage to the cable.

Make sure that the ventilating opening is not blocked by a table or curtain.

Otherwise, it may result in fire due to an increase in the internal temperature.

Do not place any containers containing water, vases, flowerpots, medicines as well as any metal on the product.

If water or a foreign material enters the product, disconnect the power cord and contact a Service Center.

This may result in a product malfunction, electric shock, or fire.

Do not use or keep combustible spray or flammable material near the product.

Otherwise, this may result in an explosion or fire.

Do not insert any metal, such as chopsticks, coins, pins and steel, or flammable objects, such as matches or paper, inside the product (through the ventilating openings, input and output terminals, etc).

If water or foreign material enters the product, disconnect the power cord and contact a Service Center.

Otherwise, this may result in electric shock or fire.

When using a fixed screen for a long time, an afterimage or stain may occur.

If you are not using your product for a long period of time, put it into sleep mode or use a moving screen saver.

Set a resolution and frequency appropriate to the product.

Otherwise, your eyesight may be damaged.

When using headphones or earphones, do not turn the volume too high.

Having the sound too loud may damage your hearing.

If you continually move closer to the product screen, your eyesight may be failing.

Safety Instructions

Take a rest for at least five (5) minutes after using the monitor for one

(1) hour.

This reduces the weariness of your eyes.

Do not install it in an unstable location such as an unstable rack or uneven surface or a location exposed to vibrations.

Otherwise, it may fall and cause personal injury and/or damage the product.

If you use the product in a location exposed to vibrations, it may damage the product and result in fire.

When moving the product, turn the power off and disconnect the power plug, antenna cable, and all the cables connected to the product.

Otherwise, it may result in electric shock or fire.

Ensure that children do not hang onto the product or climb up onto the product.

The product may fall and cause personal injury or death.

If you do not use the product for a long period of time, disconnect the power cord from the power outlet.

Otherwise, this may result in overheating or fire due to dust, and may result in fire due to electric shock or leakage.

Do not place any heavy items or toys or confectionery, such as cookies etc. that may attract the attention of children and to the product.

Your children may hang onto the product causing it to fall and this may result in personal injury or death.

Be careful that children do not place the battery in their mouths when removed from the remote control. Place the battery in a location that children or infants cannot reach.

If children have had the battery in their mouths, consult your doctor immediately.

When replacing the battery, insert it with right polarity (+, -).

Otherwise, the battery may become damaged or it may cause fire, personal injury or damage due to leakage of the internal liquid.

Use only the specified standardized batteries, and do not use a new battery and a used battery at the same time.

Otherwise, the batteries may be damaged or cause fire, personal injury or damage due to a leakage of the internal liquid.

The batteries (and rechargeable batteries) are not ordinary refuse and must be returned for recycling purposes. The customer is responsible for returning the used or rechargeable batteries for recycling.

The customer can return used or rechargeable batteries to a nearby public recycling center or to a store selling the same type of the battery or rechargeable battery.

Safety Instructions

Do not place the product in a location exposed to direct sunlight or near any heat such as a fire or heater.

This may reduce the lifetime of the product, and may result in fire.

Do not drop any objects onto the product or cause any impact to the product.

Otherwise, this may result in electric shock or fire.

Do not use a humidifier or kitchen table near the product.

Otherwise, this may result in electric shock or fire.

When there is a gas leak, do not touch the product or the power plug but ventilate immediately.

If a spark occurs, it may cause an explosion or fire.

If the product has been turned on for a long time, the display panel becomes hot. Do not touch it.

Keep the small accessories in a location out of the reach of children.

Be careful when adjusting the angle of the product or the height of the stand.

This may result in personal injury as your hand or fingers may become caught.

Also, if you tilt the product too far, it may fall and cause personal injury.

Do not install the product in a location low enough for children to reach.

Otherwise, it may fall and result in personal injury.

Since the front part of the product is heavy, install the product on a level and stable surface.

Do not put any heavy objects on the product.

This may result in personal injury and/or damage to the product.

Introduction

Package Contents

Note

Please make sure the following items are included with your LCD Display. If any items are missing, contact your dealer.

Contact a local dealer to buy optional items.

Note

This stand is not for the Floor Standing Type.

Unpacking

LCD Display

Manuals

Quick Setup Guide

Warranty Card

User's Guide

 

(Not available in all loca-

 

 

tions)

 

Cables

D-Sub Cable

Power Cord

Others

Introduction

Others

 

 

Remote Control

Batteries (AAA X 2)

HDD Cover

 

(Not available in all loca-

 

 

tions)

 

BNC to RCA Adaptor Jack

Sold separately

DVI Cable

Wall Mount KIT

LAN Cable

(Applicable to the MPn model only)

TV tuner box

NetWork Box

Semi Stand KIT

(Applicable to the MP model only)

BNC Cable

Note

You can purchase and connect a separate network box or TV tuner box. For information on how to use these, refer to their respective user manuals.

You can only connect one external box.

Introduction

Your LCD Display

Front

MENU button [MENU]

Opens the on-screen menu and exits from the menu. Also use to exit the OSD menu or return to the previous menu.

Navigate buttons (Up-Down buttons)

Moves from one menu item to another vertically or adjusts selected menu values.

Adjust buttons (Left-Right buttons) / Volume buttons

Moves from one menu item to another horizontally or adjusts selected menu values. When OSD is not on the screen, push the button to adjust volume.

ENTER button [ENTER]

Activates a highlighted menu item.

SOURCE button [SOURCE]

Switches from PC mode to Video mode. Changing the source is only allowed for external devices that are connected to the LCD Display at the time.

[PC] → [DVI] → [AV] → [HDMI] → [MagicInfo] → [TV] → [BNC]→ [Component]

Note

The TV menu is available when a TV tuner box is installed.

The MagicInfo menu is available when a network box is installed in the MPn or MP model.

D.MENU

Opens the on-screen D.MENU.

Note

This is available when a TV tuner box is installed.

Power button []

Introduction

Use this button for turning the LCD Display on and off.

Power indicator

Shows PowerSaver mode by blinking green

Note

See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your LCD Display OFF when it is not needed or when leaving it unattended for long periods.

Remote Control Sensor

Aim the remote control towards this spot on the LCD Display.

Rear

Note

For detailed information concerning cable connections, refer to Connecting Cables under Setup. The LCD Display 's configuration at the back may vary slightly depending on the LCD Display model.

POWER S/W ON [ ] / OFF [O]

Switches the LCD Display On/Off.

POWER IN

The power cord plugs into the LCD Display and the wall plug.

Introduction

RS232C OUT/IN (RS232C Serial PORT)

MDC(Multiple Display Control) Program Port

DVI / PC / HDMI IN [DVI/PC/HDMI AUDIO IN] (PC/DVI/HDMI Audio Connection Terminal (Input))

DVI / PC / HDMI IN [HDMI]

Connect the HDMI terminal at the back of your LCD Display to the HDMI terminal of your digital output device using a HDMI cable.

DVI / PC / HDMI IN [RGB](PC Video Connection Terminal)

Using a D-Sub Cable (15 pin D-Sub) - PC mode (Analog PC)

DVI / PC / HDMI IN [DVI] (PC Video Connection Terminal)

Using a DVI Cable (DVI-D to DVI-D) - DVI mode (Digital PC)

DC OUT [5V/1.5A]

Connect this to the POWER connector of a TV tuner box or network box.

AV IN [VIDEO] (VIDEO Connection Terminal)

Connect the [ VIDEO ] terminal of your monitor to the video output terminal of the external device using a VIDEO cable.

AV AUDIO IN [L-AUDIO-R](LCD Display

Audio Connection Terminal (Input))

AV AUDIO OUT [L-AUDIO-R] (LCD Display Audio Connection Terminal (Output))

Introduction

BNC/COMPONENT OUT[R/PR, G/Y, B/PB, H, V]

(BNC/Component Connection Terminal (Output))

BNC (Analog PC) Connection: connecting the R, G, B, H, V ports.

Component Connection: connecting the PR, Y, PB ports.

BNC/COMPONENT IN[R/PR, G/Y, B/PB, H, V]

(BNC/Component Connection Terminal (Input))

RGB OUT

(Applicable to the MPn model only)

LAN (LAN Connection Terminal)

(Applicable to the MPn model only)

USB(USB Connection Terminal)

Keyboard / Mouse, Mass Storage Device Compatible.

(Applicable to the MPn model only)

Note

The number of LCD Displays that can be connected to loopout may differ depending on the cables, signal source etc. With cables where there is no degradation or signal source, up to ten LCD Displays can be connected.

Introduction

Kensington Lock

The Kensington Lock is a device used to physically fix the system when using it in a public place. The locking device has to be purchased separately. The appearance and locking method may differ from the illustration depending on the manufacturer. Refer to the manual provided with the Kensington Lock for proper use. The locking device has to be purchased separately.

Note

The location of the Kensington Lock may be different depending on its model.

Using the Anti-Theft Kensington Lock

1.Insert the locking device into the Kensington slot on the Monitor and turn it in the locking direction .

2.Connect the Kensington Lock cable.

3.Fix the Kensington Lock to a desk or a heavy stationary object.

Note

See Connecting Cables for further information regarding cable connections.

Remote Control

Note

The performance of the remote control may be affected by a TV or other electronic device operating near the LCD Display , causing a malfunction due to interference with the frequency.

Introduction

1. POWER

2. Off

3.Number Buttons

POWER

OFF

Number Buttons

DEL

button

+ VOL -

 

MUTE

 

TV/DTV

 

MENU

 

INFO

COLOR BUTTONS

TTX/MIX

STILL

AUTO

S.MODE

MDC

LOCK

SOURCE

ENTER/PRE-CH

CH/P

D.MENU

GUIDE

RETURN

Up-Down Left-Right buttons

EXIT

SRS

MagicInfo

P.MODE

DUAL/MTS

PIP

SWAP

Turns the product On. Turns the product Off. Press to change the channel.

Introduction

4.DEL button

5.+ VOL -

6. MUTE

7. TV/DTV

8. MENU

9.

10. INFO

11.COLOR BUTTONS

12. TTX/MIX

13.STILL

14.AUTO

15. S.MODE

The "-" button operates only for DTV. It is used to select MMS (multi-channel) for a DTV.

Adjusts the audio volume.

Pauses (mutes) the audio output temporarily. This is displayed on the lower left corner of the screen. The audio resumes if MUTE or - VOL + is pressed in the Mute mode.

Selects the TV and DTV mode directly.

Opens the on-screen menu and exits from the menu or closes the adjustment menu.

Activates a highlighted menu item.

Current picture information is displayed on the upper left corner of the screen.

Press to add or delete channels and to store channels to the favorite channel list in the “Channel List” menu.

TV channels provide written information services via teletext.

- Teletext Buttons

For more information > TTX / MIX

Press the button once to freeze the screen. Press it again to unfreeze.

Adjusts the screen display automatically in PC mode. By changing the resolution in the control panel, auto function is performed.

When pressing this button, the current mode is displayed at the bottom centre of the screen. The LCD Display has a built-in high fidelity stereo amplifier. Then press the button again to circle through available preconfigured modes. ( Standard Music

Movie Speech Custom )

16.MDC

17.LOCK

18. SOURCE

MDC Quick Launch Button.

Activates or deactivates all function keys on both the remote control and the LCD Display except for the Power and LOCK buttons.

Press the button to change the input signal SOURCE.

Changing the SOURCE is only allowed for external devices that are connected to the monitor at the time.

19.

ENTER/PRE-CH

This button is used to return to the immediately previous channel.

20. CH/P

In TV mode, selects TV channels.

21.D.MENU

DTV menu display

22.GUIDE

Electronic Program Guide (EPG) display.

23.

RETURN

Returns to the previous menu.

 

 

 

Introduction

24. Up-Down Left-Right buttons

25. EXIT

26. SRS 27.MagicInfo 28. P.MODE

Moves from one menu item to another horizontally, vertically or adjusts selected menu values.

Exits from the menu screen.

Selects SRS TruSurround XT mode.

MagicInfo Quick Launch Button.

When you press this button, current picture mode is displayed on the lower center of the screen.

AV / HDMI / TV : P.MODE

The LCD Display has four automatic picture settings that are preset at the factory. Then push button again to circle through available preconfigured modes. ( Dynamic Standard Movie

Custom )

PC / DVI / MagicInfo: M/B (MagicBright)

MagicBright is a feature providing the optimum viewing environment depending on the contents of the image you are watching. Then push button again to circle through available preconfigured

modes. (Entertain Internet Text Custom )

29. DUAL/MTS

DUAL-

STEREO/MONO, DUAL l / DUAL ll and MONO/NICAM MONO/NICAM STEREO can be operated depending on the broadcasting type by using the DUAL button on the remote control while watching TV.

MTS-

You can select MTS (Multichannel Television Stereo) mode.

 

 

Audio Type

MTS/S_Mode

Default

 

FM Stereo

Mono

Mono

Manual Change

 

 

Stereo

Mono ↔ Stereo

 

 

 

SAP

Mono ↔ SAP

Mono

30. PIP

Every time you press the button, a PIP screen appears.

 

 

- This fuction does not work for this LCD Display.

 

31.SWAP

Swaps the contents of the PIP and main image. The image in the

 

PIP window will appear on the main screen, and the main screen

 

image will appear in the PIP window.

 

- This fuction does not work for this LCD Display.

Mechanical Layout(400MP(N))

Mechanical Layout

Introduction

Samsung 460MP, 460MPn, 400MPN, 400MP User Manual

Introduction

LCD Display Head

NETWORK MODEL SIZE

Installation VESA Bracket

When installing VESA, make sure to comply with the international VESA standards.

Purchasing VESA Bracket and Installation Information : Please contact your nearest SAMSUNG Distributor to place an order. After your order is placed, installation professionals will visit you and install the bracket.

At least 2 persons are needed in order to move the LCD Display.

SAMSUNG is not responsible for any product damage or any injury caused by installation at customer's discretion.

Introduction

Dimensions

Notice

For securing the bracket on a wall, use only machine screws of 6 mm diameter and 8 to 12 mm length.

Wall Bracket Installation

Contact a technician for installing the wall bracket.

SAMSUNG Electronics is not responsible for any damages to the product or harm to customers when the installation is done by the customer.

This product is for installing on cement walls. The product may not stay in place when installed on plaster or wood.

Components

Only use the components and accessories shipped with the product.

Wall Bracket(1)

Hinge(Left 1,

Right Plastic

Screw

Screw(B)

Anchor

 

1)

Hanger

(A)(11)

(4)

(11)

 

 

(4)

 

 

 

Wall Bracket Assembly

Note

There are two hinges(left and right). Use the correct one.

1.Insert and tighten the Captive Screw in the direction of the arrow.

Introduction

When done, mount the wall bracket on the wall.

There are two hinges(left and right). Use the correct one.

A -

Captive Screw

B -

Wall Bracket

C -

Hinge (Left)

D -

Hinge (Right)

2.Before drilling into the wall, check if the length between the two locking holes at the back of the product is correct.

If the length is too short or long, loosen all or some of the 4screws on the wall bracket to adjust the length.

A -

Length between the two locking holes

3.Check the installation diagram and mark the drill points on the wall. Use the 5.0 mm bit to drill holes deeper than 35 mm. Fix each anchor in the corresponding hole. Match each of the brackets and hinge holes to the corresponding anchor holes and insert and tighten the 11 screws A.

Introduction

To mount the product on the wall bracket

The shape of the product may vary depending on the model. (The assemblies of the plastic hanger and the screw are the same)

1.Remove the 4 screws on the back of the product.

2.Insert the screw B into the plastic hanger.

Notice

Mount the product on the wall bracket and make sure it is properly fixed to the left and right plastic hangers.

Be careful when installing the product on the bracket as fingers can be caught in the holes.

Make sure the wall bracket is securely fixed to the wall, or the product may not stay in place after installation.

3.Tighten the 4 screws in step 2 (plastic hanger + screw B)to the rear holes of the product.

Introduction

4.Remove safety pin (3) and insert the 4 product holders into the corresponding bracket holes (1). Then place the product(2) so that it is firmly fixed to the bracket. Make sure to re-insert and tighten the safety pin (3) to securely hold the product to the bracket.

A -

LCD Display

B -

Wall Bracket

C -

Wall

Wall Bracket Angle Adjustment

Adjust the bracket angle to -2° before installing it on the wall.

1.Fix the product to the wall bracket.

2.Hold the product at the top in the center and pull it forward (direction of the arrow) to adjust the angle.

Note

You can adjust the bracket angle between -2° and 15°.

Introduction

Make sure to use the top center, and not the leftor the right side of the product to adjust the angle.

Mechanical Layout(460MP(N))

Mechanical Layout

Introduction

LCD Display Head

NETWORK MODEL SIZE

Installation VESA Bracket

When installing VESA, make sure to comply with the international VESA standards.

Purchasing VESA Bracket and Installation Information : Please contact your nearest SAMSUNG Distributor to place an order. After your order is placed, installation professionals will visit you and install the bracket.

At least 2 persons are needed in order to move the LCD Display.

SAMSUNG is not responsible for any product damage or any injury caused by installation at customer's discretion.

Introduction

Dimensions

Notice

For securing the bracket on a wall, use only machine screws of 6 mm diameter and 8 to 12 mm length.

Wall Bracket Installation

Contact a technician for installing the wall bracket.

SAMSUNG Electronics is not responsible for any damages to the product or harm to customers when the installation is done by the customer.

This product is for installing on cement walls. The product may not stay in place when installed on plaster or wood.

Components

Only use the components and accessories shipped with the product.

Wall Bracket(1)

Hinge(Left 1,

Right Plastic

Screw

Screw(B)

Anchor

 

1)

Hanger

(A)(11)

(4)

(11)

 

 

(4)

 

 

 

Wall Bracket Assembly

Note

There are two hinges(left and right). Use the correct one.

1.Insert and tighten the Captive Screw in the direction of the arrow.

Introduction

When done, mount the wall bracket on the wall.

There are two hinges(left and right). Use the correct one.

A -

Captive Screw

B -

Wall Bracket

C -

Hinge (Left)

D -

Hinge (Right)

2.Before drilling into the wall, check if the length between the two locking holes at the back of the product is correct.

If the length is too short or long, loosen all or some of the 4screws on the wall bracket to adjust the length.

A -

Length between the two locking holes

3.Check the installation diagram and mark the drill points on the wall. Use the 5.0 mm bit to drill holes deeper than 35 mm. Fix each anchor in the corresponding hole. Match each of the brackets and hinge holes to the corresponding anchor holes and insert and tighten the 11 screws A.

Introduction

To mount the product on the wall bracket

The shape of the product may vary depending on the model. (The assemblies of the plastic hanger and the screw are the same)

1.Remove the 4 screws on the back of the product.

2.Insert the screw B into the plastic hanger.

Notice

Mount the product on the wall bracket and make sure it is properly fixed to the left and right plastic hangers.

Be careful when installing the product on the bracket as fingers can be caught in the holes.

Make sure the wall bracket is securely fixed to the wall, or the product may not stay in place after installation.

3.Tighten the 4 screws in step 2 (plastic hanger + screw B)to the rear holes of the product.

Introduction

4.Remove safety pin (3) and insert the 4 product holders into the corresponding bracket holes (1). Then place the product(2) so that it is firmly fixed to the bracket. Make sure to re-insert and tighten the safety pin (3) to securely hold the product to the bracket.

A -

LCD Display

B -

Wall Bracket

C -

Wall

Wall Bracket Angle Adjustment

Adjust the bracket angle to -2° before installing it on the wall.

1.Fix the product to the wall bracket.

2.Hold the product at the top in the center and pull it forward (direction of the arrow) to adjust the angle.

Note

You can adjust the bracket angle between -2° and 15°.

Loading...
+ 100 hidden pages