Ryobi BT3100 User Manual

4 (1)
OPERATOR'S MANUAL 10 in. (254 mm) TABLE SAW BT3100
Your new Table Saw has been engineered and manufactured to Ryobi's high standards for dependability, ease of operation, and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the operator's manual.
Thank you for buying a Ryobi Table Saw.
SAVE THIS MANUAL FOR FUTURE REFERENCE
TABLE OF CONTENTS
Product Specifications .............................................. 2
Rules for Safe Operation ........................................ 3-6
Electrical ..................................................................... 7
Glossary of Terms For Woodworking ...................... 8
Unpacking and Tools Needed ................................... 9
Loose Parts List .................................................. 10-11
Features ............................................................... 12-14
Operating Components .............................................. 13
Power Switch ............................................................. 13
Turn Your Saw On ..................................................... 13
To Turn Your Saw Off ................................................ 13
To Lock Your Saw Switch .......................................... 13
Blades ........................................................................ 14
Assembly ............................................................. 15-20
Assembly Leg Stand .................................................. 15
Assembly Storage Brackets ....................................... 16
Mounting Leg Stand to the Table Saw Base .............. 16
To Install Front and Back Rails ............................. 16-17
To Install Miter Table and Fence ................................ 17
To Install Accessory Table and Rip Fence ................. 18
Removing/Replacing the Throat Plate ....................... 18
Blade and Guard Assembly ....................................... 19
To Check Saw Blade Installation ............................... 20
To Install Blade Guard Assembly ............................... 20
Operation ............................................................. 21-32
Basic Operation .......................................................... 21
Causes of Kickback and Avoiding Kickback .............. 21
Cutting Aids ................................................................ 21
Types of Cuts ............................................................. 22
Featherboard .............................................................. 23
How To Make a Featherboard ............................... 23
How To Mount a Featherboard ............................. 23
Settings And Adjustments ..................................... 24-27
To Remove The Blade .......................................... 24
To Check, Replace or Adjust The Riving Knife
and Blade Guard Assembly............................... 25
To Adjust the Blade Depth .................................... 26
To Adjust the Blade Angle ..................................... 26
To Set the Scale to the Blade ................................ 26
To Lock the Miter Table ......................................... 27
Making Cuts .......................................................... 27-32
To Make a Straight Cross Cut ............................... 27
To Make a Miter Cut .............................................. 28
To Make a Straight Rip Cut ................................... 28
To Make a Bevel Cross Cut .................................. 29
To Make a Bevel Rip Cut ...................................... 29
To Make a Compound Miter Cut ........................... 30
To Make a Large Panel Cut .................................. 30
To Make Non-Through Cuts .................................. 31
To Make Dado Cuts .............................................. 32
Maintenance ........................................................ 33-39
General Maintenance ................................................. 33 Lubrication
Locker Bracket Assembly ...................................... 33
Tilt / Elevating Mechanism .................................... 33
To Set Blade to 0 or 45 Degrees ................................ 34 To Check Alignment of the Rip Fence to
the Blade .......................................................... 34-35
To Adjust the Bevel Locking Lever ............................. 35
To Align the Miter Locking Clamps ............................ 35
To Adjust the Front and Rear Rail Clamps ................ 36
To Adjust the Accessory Table .................................. 36
To Adjust the Sliding Miter Table Assembly ............... 36
Checking Sliding Miter Table Assembly ................ 37-38 Making Adjustments to Sliding Miter Fence Table
Assembly .......................................................... 38-39
Troubleshooting .................................................. 40-41
Exploded View and Parts List ............................ 43-51
Parts Ordering / Service .......................................... 52
PRODUCT SPECIFICATIONS
Blade Diameter 10 in. (254 mm)
Blade Arbor 5/8 in. (16 mm)
Cutting Depth at 0° 3-9/16 in. (90.5 mm)
Cutting Depth at 45° 2-1/2 in. (63.5 mm)
Rating 120 Volts, 60 Hz-AC Only, 15 Amperes
Output Speed 4,800 RPM
Net Weight Without Workstand 75 lbs. (34.1 kg.)
Net Weight With Workstand 107 lbs. (48.6 kg.)
RULES FOR SAFE OPERATION
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures.
SYMBOL MEANING
SAFETY ALERT SYMBOL:
Indicates caution, warning, or danger. May be used in conjunction with other symbols or pictographs.
DANGER: Failure to obey a safety warning will result in serious injury to yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.
WARNING: Failure to obey a safety warning can result in serious injury to yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.
CAUTION: Failure to obey a safety warning may result in property damage or personal injury to yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.
NOTE: Advises you of information or instructions vital to the operation or maintenance of the equipment.
IMPORTANT
Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you return the tool to your nearest Ryobi AUTHORIZED SERVICE CENTER for repair. When servic­ing, use only identical Ryobi replacement parts.
WARNING:
Do not attempt to use the tool until you have read thoroughly and understand completely the operator’s manuals. Pay close attention to the safety rules, including Dangers, Warnings, and Cautions. If you use this tool properly and only for what it is intended, you will enjoy years of safe, reliable service.
CAUTION:
Carefully read through this entire operator's manual before using your new saw. Pay close attention to the Rules For Safe Operation and all Safety Alert Symbols including Danger, Warning, and Caution. If you use your saw properly and only for what it is intended, you will enjoy years of safe, reliable service.
WARNING:
Observe all normal safety precautions related to avoiding electrical shock.
WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes, which can result in severe eye damage. Before beginning tool operation, always wear safety goggles or safety glasses with side shields and a full face shield when needed. We recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields. Always wear eye protection which is marked to comply with ANSI Z87.1.
Look for this symbol to point out important safety precautions. It means attention!!! Your safety is involved.
RULES FOR SAFE OPERATION
Safe operation of this power tool requires that you read and understand this operator's manual and all labels affixed to the tool. Safety is a combination of common sense, staying alert, and knowing how your table saw works.
READ ALL INSTRUCTIONS
KNOW YOUR POWER TOOL. Read the operator's
manual carefully. Learn the saw's applications and limitations as well as the specific potential hazards related to this tool.
GUARD AGAINST ELECTRICAL SHOCK BY
PREVENTING BODY CONTACT WITH GROUNDED SURFACES. For example; pipes, radiators, ranges,
refrigerator enclosures.
KEEP GUARDS IN PLACE and in working order. Never
operate the tool with any guard or cover removed. Make sure all guards are operating properly before each use.
REMOVE ADJUSTING KEYS AND WRENCHES. Form
habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on.
KEEP WORK AREA CLEAN. Cluttered areas and
benches invite accidents. DO NOT leave tools or pieces of wood on the saw while it is in operation.
AVOID DANGEROUS ENVIRONMENT. Don't use power
tools in damp or wet locations or expose to rain. Keep work area well lit.
KEEP CHILDREN AND VISITORS AWAY. All visitors
should wear safety glasses and be kept a safe distance from work area. Do not let visitors contact tool or extension cord while operating.
MAKE WORKSHOP CHILDPROOF with padlocks or
master switches, or by removing starter keys.
DON'T FORCE TOOL. It will do the job better and safer
at the feed rate for which it was designed.
USE RIGHT TOOL. Don't force tool or attachment to do
a job it was not designed for. Don't use it for a purpose not intended.
MAKE SURE YOUR EXTENSION CORD IS IN GOOD
CONDITION. When using an extension cord, be sure to
use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. A wire gage size (A.W.G.) of at least 14 is recommended for an extension cord 25 feet or less in length. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord.
DRESS PROPERLY. Do not wear loose clothing, gloves,
neckties, or jewelry. They can get caught and draw you into moving parts. Rubber gloves and nonskid footwear are recommended when working outdoors. Also wear protective hair covering to contain long hair.
ALWAYS WEAR SAFETY GLASSES WITH SIDE
SHIELDS. Everyday eyeglasses have only impact- resistant lenses; they are NOT safety glasses.
SECURE WORK. Use clamps or a vise to hold work when
practical. It's safer than using your hand and frees both hands to operate tool.
DON'T OVERREACH. Keep proper footing and balance
at all times.
MAINTAIN TOOLS WITH CARE. Keep tools sharp and
clean for better and safer performance. Follow instructions for lubricating and changing accessories.
DISCONNECT TOOLS. When not in use, before servicing,
or when changing attachments, blades, bits, cutters, etc., all tools should be disconnected.
AVOID ACCIDENTAL STARTING. Be sure switch is off
when plugging in.
USE RECOMMENDED ACCESSORIES. The use of
improper accessories may cause risk of injury.
NEVER STAND ON TOOL. Serious injury could occur if
the tool is tipped or if the cutting tool is unintentionally contacted.
CHECK DAMAGED PARTS. Before further use of the
tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or other part that is damaged must be properly repaired or replaced by an authorized service center to avoid risk of personal injury.
USE THE RIGHT DIRECTION OF FEED. Feed work into
a blade or cutter against the direction of rotation of blade or cutter only.
NEVER LEAVE TOOL RUNNING UNATTENDED. TURN
POWER OFF. Don't leave tool until it comes to a complete
stop.
PROTECT YOUR LUNGS. Wear a face or dust mask if
the cutting operation is dusty.
PROTECT YOUR HEARING. Wear hearing protection
during extended periods of operation.
DON'T ABUSE CORD. Never yank cord to disconnect
from receptacle. Keep cord from heat, oil, and sharp edges.
USE OUTDOOR EXTENSION CORDS. When tool is
used outdoors, use only extension cords with approved ground connection that are intended for use outdoors and so marked.
ALWAYS KEEP THE BLADE GUARD AND RIVING
KNIFE (SPLITTER) IN PLACE and in working order.
KEEP BLADES CLEAN AND SHARP. Sharp blades
minimize stalling and kickback.
KEEP HANDS AWAY FROM CUTTING AREA. Keep
hands away from blades. Do not reach underneath work or around or over the blade while blade is rotating. Do not attempt to remove cut material when blade is moving.
RULES FOR SAFE OPERATION
BLADES COAST AFTER TURN OFF.
NEVER USE IN AN EXPLOSIVE ATMOSPHERE. Normal
sparking of the motor could ignite fumes.
INSPECT TOOL CORDS PERIODICALLY. If damaged,
have repaired by a qualified service technician at an authorized service facility. The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment-grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equipment-grounding conductor to a live terminal. Repair or replace a damaged or worn cord immediately. Stay constantly aware of cord location and keep it well away from the rotating blade.
INSPECT EXTENSION CORDS PERIODICALLY and
replace if damaged.
KEEP TOOL DRY, CLEAN, AND FREE FROM OIL AND
GREASE. Always use a clean cloth when cleaning.
Never use brake fluids, gasoline, petroleum-based products, or any solvents to clean tool.
STAY ALERT AND EXERCISE CONTROL. Watch what
you are doing and use common sense. Do not operate tool when you are tired. Do not rush.
DO NOT USE TOOL IF SWITCH DOES NOT TURN IT
ON AND OFF. Have defective switches replaced by an
authorized service center.
GUARD AGAINST KICKBACK. Kickback occurs when
the blade stalls rapidly and workpiece is driven back towards the operator. It can pull your hand into the blade resulting in serious personal injury. Stay out of blade path and turn switch off immediately if blade binds or stalls.
USE RIP FENCE. Always use a fence or straight edge
guide when ripping.
SUPPORT LARGE PANELS. To minimize risk of blade
pinching and kickback, always support large panels.
BEFORE MAKING A CUT, BE SURE ALL
ADJUSTMENTS ARE SECURE.
USE ONLY CORRECT BLADES. Do not use blades with
incorrect size holes. Never use blade washers or bolts that are defective or incorrect. The maximum blade capacity of your saw is 10 in. (254 mm).
AVOID CUTTING NAILS. Inspect for and remove all nails
from lumber before cutting.
NEVER TOUCH BLADE or other moving parts during
use.
NEVER START A TOOL WHEN ANY ROTATING
COMPONENT IS IN CONTACT WITH THE WORKPIECE.
DO NOT OPERATE THIS TOOL WHILE UNDER THE
INFLUENCE OF DRUGS, ALCOHOL, OR ANY MEDICATION.
GROUND ALL TOOLS. If tool is equipped with three-
prong plug, it should be plugged into a three-hole electrical receptacle.
WHEN SERVICING use only identical Ryobi replacement
parts. Use of any other parts may create a hazard or cause product damage.
REMOVE ALL FENCES AND AUXILIARY TABLES
before transporting saw. Failure to do so can result in an accident causing possible serious personal injury.
ALWAYS USE BLADE GUARD, RIVING KNIFE, AND
ANTI-KICKBACK PAWLS on all "through-sawing" op-
erations. Through-sawing operations are those in which the blade cuts completely through the workpiece as in ripping or crosscutting. Keep the blade guard down, the anti-kickback pawls down, and the riving knife in place over the blade.
ALWAYS SECURE WORK firmly against rip fence or
miter fence.
ALWAYS USE A PUSH STICK FOR RIPPING NARROW
STOCK. A push stick is a device used to push a workpiece
through the blade instead of using your hands. Size and shape can vary but the push stick must always be nar­rower than the workpiece to prevent the push stick from contacting the saw blade. When ripping narrow stock, always use a push stick, so your hand does not come close to the saw blade. Use a featherboard and push blocks for non-through cuts.
NEVER perform any operation "freehand" which means
using only your hands to support or guide the workpiece. Always use either the rip fence or miter fence to position and guide the work.
NEVER stand or have any part of your body in line with the
path of the saw blade.
NEVER reach behind, over, or within three inches of the
blade or cutter with either hand for any reason.
MOVE THE RIP FENCE out of the way when crosscutting.NEVER use rip fence as cutoff gage when crosscutting.NEVER attempt to free a stalled saw blade without first
turning the saw OFF and disconnecting the saw from the power source.
PROVIDE ADEQUATE SUPPORT to the rear and sides
of the saw table for wide or long work pieces. Use a sturdy "outrigger" support if a table extension more than 24 inches long is attached to the saw.
AVOID KICKBACKS (work thrown back toward you) by:
A. Keeping blade sharp. B. Keeping rip fence parallel to the saw blade. C. Keeping riving knife, anti-kickback pawls, and blade
guard in place and operating.
D. Not releasing the work before it is pushed all the way
past the saw blade using a push stick.
E. Not ripping work that is twisted or warped or does not
have a straight edge to guide along the fence.
AVOID AWKWARD OPERATIONS AND HAND POSI-
TIONS where a sudden slip could cause your hand to
move into the cutting tool.
RULES FOR SAFE OPERATION
CHECK WITH A QUALIFIED ELECTRICIAN or service
personnel if the grounding instructions are not completely understood or if in doubt as to whether the tool is properly grounded.
USE ONLY CORRECT ELECTRICAL DEVICES: 3-wire
extension cords that have 3-prong grounding plugs and 3­pole receptacles that accept the tool's plug.
DO NOT MODIFY the plug provided. If it will not fit the
outlet, have the proper outlet installed by a qualified electrician.
USE ONLY RECOMMENDED ACCESSORIES listed in
this manual or addendums. Blades must be rated for at least 5,500 rpm. Use of accessories that are not listed may cause the risk of personal injury. Instructions for safe use of accessories are included with the accessory.
DOUBLE CHECK ALL SETUPS. Make sure blade is tight
and not making contact with saw or workpiece before connecting to power supply.
SECURE THE SAW TO THE LEG STAND OR A WORK-
BENCH capable of supporting the load of the saw plus any
workpiece. This is necessary to avoid any risk of the saw tipping over.
MAKE SURE THE WORK AREA HAS AMPLE LIGHT-
ING to see the work and that no obstructions will interfere
with safe operation BEFORE performing any work using the table saw.
ALWAYS TURN OFF SAW before disconnecting it, to
avoid accidental starting when reconnecting to power supply.
SAVE THESE INSTRUCTIONS. Refer to them frequently
and use to instruct other users. If you loan someone this tool, loan them these instructions also.
WARNING:
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.
SAFETY AND INTERNATIONAL SYMBOLS
This operator's manual describes safety and international symbols and pictographs that may appear on this product. Read the operator's manual for complete safety, assembly, operating and maintenance, and repair information.
SYMBOL
Do not expose to rain or use in damp locations.
• NO HANDS SYMBOL
Failure to keep your hands away from the blade will result in serious personal injury.
MEANING
SAVE THESE INSTRUCTIONS
ELECTRICAL
EXTENSION CORDS
Use only 3-wire extension cords that have 3-prong ground­ing plugs and 3-pole receptacles that accept the tool's plug. When using a power tool at a considerable distance from the power source, use an extension cord heavy enough to carry the current that the tool will draw. An undersized extension cord will cause a drop in line voltage, resulting in a loss of power and causing the motor to overheat. Use the chart provided below to determine the minimum wire size required in an extension cord. Only round jacketed cords listed by Underwriter's Laboratories (UL) should be used.
Length of Extension Cord Wire Size (A.W.G.)
Up to 25 feet 14
26-50 feet 12
When working with the tool outdoors, use an extension cord that is designed for outside use. This is indicated by the letters WA on the cord's jacket.
Before using an extension cord, inspect it for loose or exposed wires and cut or worn insulation. Repair or replace a damaged or worn cord immediately.
CAUTION:
Keep the cord away from the cutting area and position the cord so that it will not be caught on lumber, tools, or other objects during cutting.
WARNING:
The saw's motor cord must only be plugged into the receptacle provided on the saw which is controlled by the saw's master switch. cord directly into an extension cord as this will prevent the ability to switch the saw OFF.
See Figure 1.
Never plug the motor
ELECTRICAL CONNECTION
Your Ryobi Table Saw is powered by a precision built electric motor. It should be connected to a power supply
that is 120 volts, 60Hz, AC only (normal household current). Do not operate this tool on direct current (DC). A
substantial voltage drop will cause a loss of power and the motor will overheat. If the saw does not operate when plugged into an outlet, double check the power supply.
GROUNDING INSTRUCTIONS
In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances.
Do not modify the plug provided. If it will not fit the outlet, have the proper outlet installed by a qualified electrician. Improper connection of the equipment-grounding conductor can result in a risk of electric shock. The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment-grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equipment-grounding conductor to a live termi­nal.
Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to whether the tool is properly grounded.
Repair or replace a damaged or worn cord immediately.
This tool is intended for use on a circuit that has an outlet like the one shown in one shown.
Figure 1.
It also has a grounding pin like the
GROUNDING
PIN
SAW RECEPTACLE
MOTOR CORD
POWER CORD
COVER OF GROUNDED
OUTLET BOX
Fig. 1
GLOSSARY OF TERMS
Anti-Kickback Pawls (Fingers)
Device which, when properly installed and maintained, is designed to stop the workpiece from being kicked back toward the front of the saw during a ripping operation.
Arbor
The shaft on which a blade or cutting tool is mounted.
Bevel Cut
A cutting operation made with an angled blade.
Compound Cut
A cut with both a miter angle and a bevel angle.
Crosscut
A cutting or shaping operation made across the grain of the workpiece.
Dado
A non-through cut which produces a square sided notch or trough in the workpiece.
Featherboard
A device used to help control the workpiece by guiding it securely against the table or fence during any rip cut operation.
Freehand
Performing a cut without using a fence, miter gauge, fixture, hold down clamp, or other proper device to keep the workpiece from twisting during the cut.
Gum
A sticky, sap based residue from wood products.
Heel
Misalignment of the blade.
Kerf
The amount of material removed by the blade in a through cut or the slot produced by the blade in a non-through or partial cut.
Kickback
An uncontrolled grabbing and throwing of the workpiece back toward the front of the saw. Associated with the workpiece closing the kerf and pinching the blade or otherwise placing tension on the blade.
Leading End
The end of the workpiece which, during a rip type operation, is pushed into the cutting tool first.
Miter Cut
A cutting operation made with the wood at any angle other than 90 degrees.
Molding
A cut which produces a special shape in the workpiece, used for joining or decoration.
Non-Through Cuts
Any cutting operation where the blade does not extend completely through the thickness of the workpiece.
Push Block
A device used to feed the workpiece through the saw, except during narrow ripping type operations where a push stick should be used. It also helps keep the operator's hands well away from the blade.
Push Stick
A device used to feed the workpiece through the saw to help keep the operator's hands well away from the blade.
Rabbet
A notch in the edge of a workpiece.
Resin
A sticky, sap base substance that has hardened.
Ripping Or Rip Cut
A cutting or shaping operation made along the length or with the grain of the workpiece.
Riving Knife
Also known as a spreader or splitter. A metal piece, slightly thinner than the saw blade which helps keep the kerf open and prevent kickback.
Revolutions Per Minute (RPM)
The number of turns completed by a spinning object in one minute.
Saw Blade Path
The area over, under, behind, or in front of the blade. As it applies to the workpiece, that area which will be, or has been, cut by the blade.
Set
The distance that the tip of the sawblade tooth is bent (or set) outward from the face of the blade.
Throw-Back
Throwing of a workpiece in a manner similar to a kickback. Usually associated with a cause other than the kerf closing, such as a workpiece being dropped onto the blade or being placed inadvertently in contact with the blade.
Through Sawing
Any cutting operation where the blade extends completely through the thickness of the workpiece.
Trailing End
The workpiece end last cut by the blade in a ripping operation.
Workpiece
The item on which the cutting operation is being done. The surfaces of a workpiece are commonly referred to as faces, ends, and edges.
UNPACKING
Your Model BT3100 Table Saw is shipped complete in one carton and includes two table extensions, a rip fence, a miter fence with adjusting clamp, a blade guard, rails, and leg stand.
Separate all parts from packing materials and check each one with the illustration and the list of Loose Parts to make sure all items are accounted for, before discarding any packing material.
If any parts are missing, do not attempt to assemble the table saw, plug in the power cord, or turn the switch on until the missing parts are obtained and are installed correctly. Call 1-800-525-2579 in the United States or 1-800-265-6778 in Canada for assistance if any parts are missing or damaged.
TOOLS NEEDED
3/8 in. NUT DRIVER
The saw is factory set for accurate cutting. After assem­bling it, check for accuracy. If shipping has influenced the settings, refer to specific procedures explained in the opera­tion and maintenance sections of this manual.
WARNING:
If any parts are missing, do not operate this tool until the missing parts are replaced. Failure to do so could result in possible serious personal injury.
3/4 in.
WRENCH
SOCKET WRENCH
WITH 7/16 in.
SOCKET
COMBINATION
SQUARE
ADJUSTABLE
WRENCH
#2 PHILLIPS
SCREWDRIVER
FLAT BLADE
SCREWDRIVER
FRAMING SQUARE
Fig. 2
LOOSE PARTS LIST
8
4
5
7
6
3
2
1
21
20
8
19
18
15
15
17
Key No. Description Quan.
1 Rip Scale Indicator .......................................... 1
2 Screw .............................................................. 1
3 Hex Nut ........................................................... 1
4 End Plug ......................................................... 4
5 Rip Fence........................................................ 1
6 Sliding Miter Table .......................................... 1
7 Accessory Table ............................................. 1 8 Blade Guard With Riving Knife
and Anti-Kickback Pawls................................. 1
9 Large Wrench ................................................. 1
10 Small Wrench.................................................. 1
11 Rear Rail ......................................................... 1
12 Front Rail ........................................................ 1
16
14
13
9
11
12
10
Fig. 3
Key No. Description Quan.
13 Screw .............................................................. 1
14 Washer............................................................ 1
15 Knob................................................................ 1
16 Adjusting Clamp .............................................. 1 17 Miter Fence With Miter Indicator and Locator
Pin Pivot ...................................................... 1
18 3/32 in. Hex Key (Included)............................. 1
19 1/8 in. Hex Key (Included)............................... 1
20 5/32 in. Hex Key (Included)............................. 1
21 3/16 in. Hex Key (Included)............................. 1 22 Instructional Video (Not Shown) 23 Operator's Manual (Not Shown) 24 Warranty Registration Card (Not Shown)
Page 10
LOOSE PARTS LIST
The following items are included with your table saw leg stand.
G
I
J
C
K
B
A
M
L
K
D
E
I
D
E
D
E
H
G
E D
F
C
M
D
E
A
B
D
E
J
K
C
D
F
E
G
K
J
E
J
D
H
G
C
H
D
E
E
D
F
A. Storage Bracket ..................................................... 4
B. Screw (1/4-20 x 1/2 in. Pan Hd.) ............................ 4
C. Lower Brace ...........................................................4
D. Hex Nut (5/16-18) ................................................ 32
E. Washer (5/16 in.)..................................................32
F. Leveling Foot ......................................................... 4
G. Leg ......................................................................... 4
E D
H. Carriage Bolt (5/16-18 x 3/4 in.) ..........................24
I. Upper Brace ...........................................................2
J. Hex Nut (1/4-20) ....................................................8
K. Washer (1/4 in.)....................................................12
L. Bolt (1/4-20 x 3/4 in. Hex Hd.) ............................... 4
M. Upper Side Brace...................................................2
Page 11
F
Fig. 4
FEATURES
Your saw is designed to perform as a versatile, accurate, precision cutting tool that is easy to operate.
It is equipped with the following features for convenience, ease of use, and high-quality performance:
• a combination saw blade
• a bevel indicator to set the exact angle of the blade, with locking lever
• an adjustable and reversible sliding miter table
• an adjustable miter fence with miter indicator
• an adjustable accessory table
• an adjustable rip fence with scale indicator
• an adjustable riving knife (splitter) and blade guard with anti-kickback pawls
GETTING TO KNOW YOUR SAW
SLIDING
MITER TABLE
THROAT
PLATE
BLADE GUARD
ASSEMBLY
ANTI-KICKBACK
PAWLS
RIVING KNIFE
• front and rear guide rails with an easy-to-read scale on front rail
• a dust exhaust that can be adapted to a standard shop vacuum
• blade adjusting handle to set depth of cut
• switch with lockable cover plate to help prevent unauthorized use
These features provide ease of cutting with all types of wood.
WARNING:
Before attempting to use your table saw, familiarize yourself with all operating features and safety requirements.
SAW BLADE
REAR RAIL
RIP FENCE
ACCESSORY
TABLE
SCALE
INDICATOR
SCALE
ADJUSTING
CLAMP
MITER FENCE
FENCE HOLDER
END PLUG (4)
MITER SCALE
LOCKING CLAMPS
QUICK-STOP
MITER
MITER
FRONT RAIL
RIP FENCE
LOCKING HANDLE
SWITCH WITH
LOCKABLE COVER
BLADE
ADJUSTING HANDLE
BEVEL
LOCKING LEVER
BEVEL
INDICATOR
STORAGE
BRACKETS
MITER
SLIDE LOCK
MITER
TABLE BASE
BEVEL SCALE
LEVELING FOOT
LEG STAND
Fig. 5
Page 12
FEATURES
WARNING:
Although some of the illustrations in this manual are shown with the blade guard removed for clarity, do not operate the saw without the blade guard unless specifically instructed to do so.
OPERATING COMPONENTS
The upper portion of the blade projects up through the table, surrounded by an insert called the throat plate. To cut wood at a bevel, the blade must be tilted, using the blade adjust­ment handle, scale, and bevel indicator found on the front of the cabinet. Inside the cabinet, adjustable positive stops are provided for 0º and 45º.
The sliding miter table assembly is used for all crosscutting operations. The miter fence is easily adjusted to cut wood at an angle by loosening the adjusting clamp, setting the fence to the miter scale, and retightening the clamp. The sliding miter table, which rests on a base mounted on the rails, can be repositioned along the rails for wide work. It can be reversed so the projecting base is in the back. It can also be moved from the right side to the left side as needed. With the miter fence removed the miter table offers additional support for other operations such as ripping.
Your saw includes a rip fence and an accessory table. The accessory table can be moved from the right side of the saw to the left side as needed. The rip fence is used to position work that will be cut lengthwise. A scale on the front rail shows the distance between the rip fence and the blade.
The riving knife is a metal device directly behind and above the blade. It is used to help keep the cut wood from binding together and causing possible kickback. It is very important to use the riving knife for all through-sawing operations. The anti-kickback pawls are toothed plates mounted on the riving knife. Their teeth point away from the work in case the work should be pulled back, toward the operator. Then the teeth dig into the wood to help prevent or reduce the possibility of kickback.
Your Ryobi BT3100 table saw features a receptacle on the right side of the cabinet that permits use of accessories. Use only accessories that are listed for use with this tool. When using a listed accessory, unplug the saw motor cord and use the receptacle and BT3100 main power switch to operate the accessory.
POWER SWITCH
See Figure 6.
Your BT3100 is equipped with a switch that utilizes a lockable switch cover to prevent unauthorized use. With the saw turned OFF, a padlock can be used to secure the switch cover over the switch. This prevents anyone from starting your saw without removing the padlock, lifting the switch cover, and pressing the switch button.
TO TURN YOUR SAW ON:
1. Lift switch cover.
2. Press switch button.
3. Lower switch cover.
TO TURN YOUR SAW OFF:
1. Press or push outside of switch cover, or
2. Lift switch cover and press switch button.
TO LOCK YOUR SAW SWITCH:
1. Raise switch cover.
2. Align metal loop through slot in switch cover while lowering switch cover.
3. Place shackle of padlock (not provided) through the metal loop and close padlock.
WARNING:
ALWAYS make sure your workpiece is not in contact with the blade before operating the switch to start the tool. Failure to heed this warning may cause the workpiece to be kicked back toward the operator and result in serious personal injury.
WARNING:
To reduce the risk of accidental starting, ALWAYS make sure the switch is in the OFF position before plugging tool into the power source .
SWITCH
COVER
SWITCH
BUTTON
TO
START
TO
STOP (B)
TO LOCK IN
OFF POSITION
PADLOCK
(NOT PROVIDED)
STOP (A)
Fig. 6
TO
Page 13
FEATURES
BLADES
It is recommended that you use only the RYOBI 10 in. (254 mm) Combination Blade, which is for use with the BT3100 Table Saw. You will get maximum performance with the following features:
• 36 precision ground, micro-grain carbide teeth • laser-cut expansion slots
• kerf width of 2.5 mm + .02 • tensioning for 4,800 rpm
This blade is provided with the saw. Additional blade styles of the same high quality are available for specific operations such as ripping. Your local RYOBI dealer can provide you with complete information.
CAUTION:
Be sure to use only blades that are rated for at least 5,500 RPM and recommended for use on this saw.
PRECISION GROUND
MICRO-GRAIN
CARBIDE TEETH
SPEED AND WIRING
The no-load speed of your table saw is approximately 4,800 rpm. The speed will not remain constant but will be less under a load. The wiring in a shop is as important as the motor's horsepower rating. A line intended for lights only WILL NOT PROPERLY CARRY A POWER TOOL MOTOR. Wire that is heavy enough for a short distance will be too light for a greater distance. A line that can support one power tool may not be able to support two or three tools.
LASER-CUT BODY
AND EXPANSION SLOTS
BLADE ROTATION
Fig. 7
WARNING:
To prevent possible electrical hazards, have a qualified electrician check the line if you are not certain that it is properly wired.
Page 14
ASSEMBLY
Assembly is best done in the area where the saw will be used. When you remove the table saw base, loose parts, and hardware from the packing materials, check all items with the loose parts list and drawing. If you are unsure about the description of any part, refer to the drawing. If any parts are missing, delay assembling until you have obtained the missing part(s).
ASSEMBLING LEG STAND
See Figures 8 and 9.
Take the following hardware from the leg stand hardware
bag: 24 carriage bolts (5/16-18 x 3/4 in.) 4 leveling feet 32 flat washers (5/16 in.) 32 hex nuts (5/16-18)
Note: Remaining hardware from this bag is used for mount-
ing leg stand on the table saw base and mounting storage brackets to upper brace.
Take 4 legs and 8 braces from loose parts.Place an upper side brace inside two of the legs, with the
legs wide end up. (Upper side braces have two large holes in each end.) Make sure the two posts on the leg align with the small holes on the brace.
UPPER BRACE
Align the two large holes on the brace and the legs. Insert
the carriage bolts. Add flat washers and hex nuts and hand tighten. Repeat for the other upper brace. These are the front and back sets.
For the side sets, install a upper brace on two legs. Add
hardware and finger tighten. Repeat for the other upper brace.
Use the same steps to install the lower braces. Tighten all
hex nuts with a wrench.
Place a hex nut and flat washer on each leveling foot.
Install the leveling feet from the bottom of each leg with the bolts pointing up. Cap with the remaining flat washers and hex nuts but do not tighten.
Move the leg set to desired location. Adjust the leveling
feet with a wrench, then tighten the top hex nut.
BOLT
HEX NUT
WASHER
CARRIAGE
BOLT
WASHER
SCREW
STORAGE
BRACKET(S)
UPPER
SIDE BRACE
LOWER BRACE
WASHER
HEX NUT
LEG
HEX NUT
HEX NUT
WASHER
LEVELING FOOT
HEX NUT
Fig. 8
Page 15
ASSEMBLY
ASSEMBLING STORAGE BRACKETS
See Figure 9.
Take storage brackets from loose parts.
Take the following hardware from the leg stand hardware
bag:
4 screws (1/4-20 x 1/2 in. Pan Hd.) 4 hex nuts (1/4-20) 4 washers (1/4 in.)
Secure storage brackets to upper braces of leg stand as
shown in figures 8 and 9.
MOUNTING THE LEG STAND ON THE TABLE SAW BASE
See Figure 10.
Take the following from a small hardware bag:
4 hex bolts (1/4-20 x 3/4 in.) 4 hex nuts (1/4-20) 8 flat washers (1/4 in.)
Note: This hardware was in the bag with hardware for assembling the leg stand and leveling feet.
WARNING:
Do not lift the saw without help. The saw base weighs approximately 75 lbs. Hold it close to your body. Keep your knees bent and lift with your legs, not your back. Ignoring these precautions can result in back injury.
STORAGE BRACKET(S)
LEG
LEG STAND ASSEMBLED
UPPER BRACE
LOWER BRACE
Fig. 9
Place the leg stand on the table saw base. Align the holes
in the table with the holes in the end braces.
Place a flat washer on a bolt and insert through hole. Add
a flat washer and a hex nut. Hand tighten.
Repeat for three remaining holes. Tighten all hardware
with a wrench. You may find it helpful to use one wrench to hold the head of the bolt and one to tighten the hex nut.
See Figure 10.
WARNING:
Do not connect to power supply until assembly is complete. Failure to comply could result in accidental starting and possible serious injury.
TO INSTALL FRONT AND BACK RAILS
See Figures 11 and 12.
Position end plugs on both rails and secure in place by
tapping with a block of wood or a rubber mallet.
Loosen the front rail clamps one half turn from the tightened
position. Loosen the square rail holder nut one-fourth (1/4) turn to allow the front rail to slide over it.
11 and 12.
Mount the front rail with the scale facing the outside
toward the operator.
See Figures
HEX BOLT
SAW BASE
FLAT
WASHER
LEG STAND
HEX NUT
Page 16
Fig. 10
Loading...
+ 36 hidden pages