Rival 8420, 8620, 8605, 8550-X, 8405 User Manual

...
4 (2)
Rival 8420, 8620, 8605, 8550-X, 8405 User Manual

8405, 8420, 8455-X, 8550-X, 8605, 8620

Electric Ice Cream Maker

Owner’s Guide

READ AND SAVE THESE INSTRUCTIONS

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be followed, including the following:

1.Read all instructions before using.

2.To protect against electrical shock, do not immerse cord, plug, or motor in water or other liquid.

3.Close supervision is necessary when any appliance is used by or near children.

4.Unplug from outlet when not in use and before putting on or taking off parts, and before cleaning.

5.Avoid contacting moving parts.

6.Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions, or has been dropped or damaged in any manner. See warranty to return for examination, repair, or electrical or mechanical adjustment.

7.The use of accessory attachments (not recommended or sold by Rival®) may cause fire, electric shock or injury.

8.Do not use outdoors.

9.Do not let cord hang over edge of table or counter, or touch heated surfaces, including the stove.

10.Do not use appliance for other than intended use.

11.Do not operate your Ice Cream Maker dry. Always have ice cream mixture in the ICE CREAM CAN when you plug in your appliance.

12.The ICE CREAM CAN should be thoroughly towel dried after use and washing. If the ICE CREAM CAN is left to “air dry”, water spots may appear.

SAVE THESE INSTRUCTIONS

This appliance is for HOUSEHOLD USE ONLY. No user-serviceable parts inside. Power Unit never needs lubrication. Do not attempt to service this product.

POLARIZED PLUG

appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit in a polarized outlet only one way. If the plug does not fit fully

in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.

-2-

-3-

KNOW YOUR ICE CREAM MAKER

WOOD BUCKET: 8455-X (4 quart), 8550-X (5 quart)

PLASTIC BUCKET: 8401 (4 quart), 8420 (4 quart), 8405 (4 quart tall), 8605 (6 quart), 8620 (6 quart)

Motor Drive

Top mounted. Engages stem of DASHER.

Cork

Used to plug hole in COVER when hardening and ripening ice cream.

Cover

Tab in COVER fits notch in ice cream can.

Dasher

Stem on top fits through hole in center of COVER, and engages MOTOR DRIVE.

Ice Cream Can

Container holds ice cream mixture.

Drain Hole

Allows salt water to flow freely out of BUCKET.

motor drive

cork cover

dasher

ice cream can

tab plates

latch

drain hole

Bucket bucket

Latch and tab plates secure MOTOR DRIVE.

Drain hole located near top of BUCKET. Holds rock salt and ice.

HOW TO USE YOUR ICE CREAM MAKER

NOTE: Before using for the first time, wash all parts except MOTOR DRIVE (see “HOW TO CLEAN YOUR ICE CREAM MAKER”).

1.Pour chilled ice cream mixture into cooled ICE CREAM CAN. Fill ICE CREAM CAN only 3/4 full, as mixture will expand during freezing.

2.Insert DASHER. Be sure that bottom of DASHER fits indentation at bottom of ICE CREAM CAN.

3.Place COVER on ICE CREAM CAN.

 

 

MAKER SIZE

 

For best results use Rival® Rock Salt

4 Quart

 

5 Quart

 

6 Quart

 

 

 

 

 

 

 

ROCK SALT for making ice cream

3 Cups

 

312

Cups

 

4 Cups

ROCK SALT for hardening ice cream

2 Cups

 

212

Cups

 

3 Cups

CRUSHED ICE for making and hardening ice cream

17 lbs.

 

22 lbs.

 

25 lbs.

 

 

 

 

 

 

 

4.Place filled ICE CREAM CAN in BUCKET. Make sure ICE CREAM CAN is centered and engages with bottom of BUCKET.

5.Place MOTOR DRIVE over ICE CREAM CAN so that stem of DASHER engages hole in bottom of MOTOR DRIVE. Rotate ICE CREAM CAN slightly until MOTOR DRIVE engages ICE CREAM CAN COVER. Fit the two tabs at the end of MOTOR DRIVE into tab plate. Lower the rounded tab (at other end of MOTOR DRIVE) onto latch plate. Rotate latch lock over rounded tab. Plug power cord into 120 volt AC outlet.

6.While ice cream maker is running, distribute 2 inches of ice around bottom of BUCKET. Sprinkle approximately 1/4 cup salt uniformly over layer of ice.

Exception: For Models 8455-X and 8550-X, layer 1 inch of ice with 1/2 cup salt.

(See “Hints”) NOTE: The DASHER does not move, the ICE CREAM CAN turns around it.

7.Continue adding layers of ice, with salt between layers, until ice level reaches top of rotating ICE CREAM CAN. NOTE: Should ice cream maker stop before churning is complete (approximately 20-40 minutes), check to see if large ice cubes are jammed against the rotating ice cream can.

(See “Important Points”)

8.Ice cream should churn about 20-40 minutes or until motor stops. Unplug and remove MOTOR DRIVE.

9.Clear ice and salt away from top of ice cream can. Wipe carefully to remove salt and water before removing the COVER. Lift out DASHER and scrape clean with a rubber spatula. Pack ice cream down into ICE CREAM CAN.

-4-

-5-

Loading...
+ 6 hidden pages