Radio Shack ET-1105 User Manual

Size:
1.46 Mb
Download

43-1105.fmPage 1 Monday, August 30, 1999 1:57 PM

Cat. No. 43-1105

OWNER’S MANUAL

Please read before using this equipment.

ET-1105

Digital Spread Spectrum

900 MHz Cordless Telephone

with Caller ID/Call Waiting ID

43-1105.fmPage 2 Monday, August 30, 1999 1:57 PM

FEATURES

Your RadioShack ET-1105Digital Spread Spectrum 900 MHz Cordless Telephone uses advanced digital cordless technology to give you superior sound quality and extended range. The telephone digitizes and scrambles your conversation before transmitting it between the handset and the base, so your conversation is secure from interception by other cordless telephone or scanner users. Its cordless operation lets you handle calls just about anywhere in your home or office.

The phone can display a caller’s phone number, name (if available), and the date and time the call was received. It can store up to 45 records as provided by your local phone company to Caller ID service subscribers.

If you have Call Waiting with Caller ID, the phone displays incoming caller information for a new call when you are already on the phone.

The ET-1105has these features:

900 MHz Operation — provides better sound and less interference than many other cordless phones.

Digital Spread Spectrum — provides the longest range and the utmost in security. Frequencies are constantly changing across the entire 900 MHz band, making your calls impossible to monitor on scanners.

Headset Jack — lets you connect an optional headset (such as RadioShack Cat. No.43-195)forhands-freeconvenience while you use the phone.

20-NumberMemory Dialing— lets you store 20 numbers in memory for easy dialing.

Volume Control — lets you adjust the volume you hear through the handset.

Page — lets you send a paging signal from the base to the handset to page someone or locate the handset when it is away from the base.

4-HourTalk or7-DayStandby Time— lets you talk for 4 hours or keep the phone off the base for 7 days without recharging (with a fully charged battery pack).

Caller ID Memory Dialing — lets you select a phone number stored in Caller ID memory, then dial it with the touch of a button.

20 Channels — automatically selects a clear channel when you make or answer a call.

VIP Memory — alerts you with a distinctive ring when someone you have added to the VIP list calls.

© 1999 Tandy Corporation.

All Rights Reserved.

RadioShack is a registered trademark used by Tandy Corporation.

2

43-1105.fmPage 3 Monday, August 30, 1999 1:57 PM

Review Scrolling — lets you easily scroll through all information stored in theET-1105’sCaller ID memory.

Phone Information Display — lets you see incoming Caller ID information and phone numbers as you dial them or recall them from the ET-1105’s memory and Caller ID records.

Trilingual Messages — lets you set the phone to display messages in English, French, or Spanish.

Out of Range Signal — the handset beeps twice to let you know when you move out of the base’s operating range.

Security Access-ProtectionCode— helps prevent other cordless phone users from using your phone line while the handset is off the base.

Flash — sends an electronic switchhook signal for use with special phone services such as Call Waiting.

Redial — lets you quickly redial the last number dialed.

Tone/Pulse Dialing — lets you use your phone with tone or pulse service.

This telephone has been tested and found to comply with all applicable UL and FCC standards.

WARNING: To reduce the risk of fire or shock hazard, do not expose this product to rain or moisture.

CAUTION

!

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER OR BACK. NOUSER-SERVICE-ABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.

This symbol is intended to alert you to the presence of uninsulated dangerous voltage within the product’s enclosure that might be of sufficient magnitude to constitute a risk of electric shock. Do not open the product’s case.

This symbol is intended to inform you that important operating and ! maintenance instructions are included in the literature accom-

panying this product.

3

43-1105.fmPage 4 Monday, August 30, 1999 1:57 PM

Important Caller ID Information

To use the phone’s Caller ID and Call Waiting features, you must be in an area where Caller ID and Call Waiting services are available and you must subscribe to the services.

Where Caller ID is offered, one or more of the following options are generally available:

Caller’s number only

Caller’s name only

Caller’s name and number

For the ET-1105’sCaller ID memory dial feature to operate, you must receive the caller’s number.

Important: Cordless phones such as this one require AC power to operate. When the AC power is off, you cannot dial out or receive incoming calls using yourET-1105.For this reason, the ET1105 cordless phone should not be your only telephone. To be safe, you should also have a corded phone that does not require AC power to operate so you can still make and receive calls if there is an AC power failure.

Your telephone operates on standard radio frequencies as allocated by the FCC. Even though the access protection code prevents unauthorized use of your phone line, it is possible for other radio units operating on similar frequencies within a certain area to unintentionally intercept your conversations and/or cause inter-

4

ference. This lack of privacy can occur with any cordless phone.

READ THIS BEFORE INSTALLATION

Each device that you connect to the phone line draws power from the phone line. We refer to this power draw as the device’s ringer equivalence number, or REN. The REN is on the bottom of the base.

If you are using more than one phone or other device on the line, add up all the RENs. If the total is more than five (three in rural areas), your phone might not ring. If ringer operation is impaired, remove a device from the line.

FCC STATEMENT

This telephone complies with Part 68 of FCC Rules. You must, upon request, provide the FCC registration number and the REN to your phone company. These numbers are on the bottom of the base.

Note: You must not connect your ET1105 to any of the following:

coin-operatedsystems

party-linesystems

most electronic key phone systems

43-1105.fmPage 5 Monday, August 30, 1999 1:57 PM

CONTENTS

 

Preparation ..............................................................................................................

6

Selecting a Location ...........................................................................................

6

Attaching the Handset’s Antenna .......................................................................

6

Placing the Base on a Desk Top ........................................................................

6

Mounting the Base on a Wall Plate ....................................................................

8

Connecting and Charging the Battery Pack .......................................................

9

Setting the Dialing Mode ..................................................................................

11

Selecting the Language ....................................................................................

11

Setting the Area Code ......................................................................................

12

Setting the Ringer .............................................................................................

12

Turning the Ringer On or Off ......................................................................

12

Checking/Setting the Ringer ......................................................................

12

Using a Headset ...............................................................................................

13

Removing the Belt Clip .....................................................................................

13

Telephone Operation ............................................................................................

14

Making and Receiving a Call ............................................................................

14

Setting the Handset’s Volume ..........................................................................

14

Using Redial .....................................................................................................

14

Using Flash ......................................................................................................

15

Using Tone Services on a Pulse Line ...............................................................

15

Using Page .......................................................................................................

15

Memory Dialing ................................................................................................

15

Storing a Number and Name in Memory ...................................................

16

Using the VIP Call List ...............................................................................

16

Entering a Pause .......................................................................................

17

Recalling Numbers Stored in Memory .......................................................

17

Dialing a Memory Number .........................................................................

17

Chain-DialingService Numbers .................................................................

17

Testing Stored Emergency Numbers .........................................................

18

Deleting Information in a Single Memory Location ....................................

18

Deleting Information in All Memory Locations ...........................................

18

Caller ID Operation ...............................................................................................

19

Caller ID Displays .............................................................................................

20

Reviewing Caller ID Records ............................................................................

21

Storing Caller ID Records in a Memory Location .............................................

21

Dialing Numbers from a Caller ID Record ........................................................

21

Deleting Caller ID Records ...............................................................................

21

Troubleshooting ....................................................................................................

22

Care and Maintenance ..........................................................................................

25

 

5

43-1105.fmPage 6 Monday, August 30, 1999 1:57 PM

PREPARATION

SELECTING A LOCATION

You can place the phone on a desk top or table, or mount it on a standard wall plate. Select a location that is:

near an accessible AC outlet

near a telephone line jack

out of the way of normal activities

away from electrical machinery, electrical appliances, metal walls or filing cabinets, wireless intercoms, alarms, and room monitors

The base’s location affects the phone’s range. If you have a choice of several locations, try each to see which provides the best performance.

Caution: The supplied AC adapter was designed specifically for yourET-1105.Use only the supplied adapter.

PLACING THE BASE ON A DESK TOP

Follow these steps to place the base on a desk, shelf, or table.

1.Remove the bracket by holding in both tabs and gently pulling out the wide end of the bracket.

Tabs

2.Plug one end of the supplied long modular cord into the phone jack on the back of the base.

ATTACHING THE HANDSET’S ANTENNA

Screw the antenna into the hole at the top of the handset.

6

43-1105.fmPage 7 Monday, August 30, 1999 1:57 PM

3.Insert the supplied AC adapter’s barrel plug into the DC 9V jack on the back of the base.

4.Route the adapter’s cord through the strain relief slot on the bottom of the base.

5.Insert the tabs on the narrow end of the bracket into both upper slots on the bottom of the base as shown and push the tabs on the wide end of the bracket into the upper slots on the bottom of the base.

6.Plug the modular cord’s other end into a modular phone line jack.

7.Plug the adapter into a standard AC outlet.

8.Raise the base’s antenna to a vertical position.

7

43-1105.fmPage 8 Monday, August 30, 1999 1:57 PM

MOUNTING THE BASE ON A WALL PLATE

1.Follow Steps 1 through 3 under “Placing the Base on a Desk Top” on Page 6.

2.Route the modular cord through the left groove on the bottom of the base and the adapter cord through the groove below the strain relief slot.

3.Insert the tabs on the narrow end of the bracket into the slots on the bottom of the base as shown and route the other end of the short modular cord through the center of the bracket.

4.Push the tabs on the wide end of the bracket into the lower slots on the bottom of the base.

5.Plug the short modular cord’s other end into the wall plate jack, align the base’s keyhole slots with the wall plate studs, and slide the base downward to secure it.

8

43-1105.fmPage 9 Monday, August 30, 1999 1:57 PM

6.Plug the adapter into a standard AC outlet.

7.Raise the base’s antenna to a vertical position.

CONNECTING AND CHARGING THE BATTERY PACK

The ET-1105comes with a rechargeablenickel-cadmiumbattery pack in the handset but not connected. Before using your phone, you must connect the battery pack and then charge it for about 16 hours.

1.Press down and slide off the compartment cover as shown.

2.Plug the battery pack’s connector into the socket in the compartment. The connector fits only one way.

Note: For easier battery pack connection, lift it out of the compartment, insert its connector into the socket, then replace the battery pack inside the compartment.

3. Replace the cover.

To charge the battery pack, place the handset on the base. The CHARGE indicator on the base lights.

Recharge the battery pack when andLOW BATTERY appear on the handset’s display.

9

43-1105.fmPage 10 Monday, August 30, 1999 1:57 PM

Notes:

You can place the handset on the base face down or face up without removing the belt clip. If you want to use the hanging hole on the back of the handset to place the handset on the wall-mountedbaseface-up,remove the belt clip (see “Removing the Belt Clip” on Page 13). However, the battery pack will not fully charge in this position.

When you first use the phone after charging or recharging the battery pack, the phone might not work and you might hear an error tone when you press TALK. If this happens, return the handset to the base for about 6 seconds. This resets the security access protection code.

If the CHARGE indicator does not light when you place the handset on the base, be sure the battery pack and AC adapter are correctly and securely connected.

Also, check the charging contacts on the handset and the base. If the contacts are dirty or tarnished, clean them with a pencil eraser.

If the battery pack gets completely discharged or the base loses power while the handset is away from it, the security access-protectioncode needs to be reset. To reset the code, place the handset on the base. If it

10

was the handset that lost power, leave the handset on the base to charge the battery pack.

If the battery pack gets weak during a call, the handset beeps once every 16 seconds. If this happens, you cannot make another call on the phone until you recharge the battery pack.

About once a month, fully discharge the battery pack by keeping the handset off the base until andLOW BATTERY appear. Otherwise, the battery pack loses its ability to fully recharge.

To avoid damage to the battery pack, always recharge the handset before battery power grows too weak to display .

If you are not going to use your phone for an extended period of time, disconnect the battery pack. This increases the battery pack’s usable life.

The supplied battery pack should last for about a year. When it loses its ability to fully recharge, order a replacement battery pack from your local RadioShack store (see “Replacing the Battery Pack” on Page 26).

43-1105.fmPage 11 Monday, August 30, 1999 1:57 PM

SETTING THE DIALING MODE

Set T/P (Tone/Pulse) on the back of the base for the type of service you have. If you are not sure which type you have, once the battery is fully charged, do this test.

1. Set T/P toT.

SELECTING THE

LANGUAGE

The ET-1105comes set to display all Caller ID messages in English, but if you want it to display messages in French or Spanish, follow these steps.

1.Press SETUP on the handset.LANGUAGE and the currently selected language appear.

T/P

2.Lift the handset, then press TALK and listen for the dial tone.

TALK

3.Press any number other than 0.

Note: If your phone system requires that you dial an access code (9, for example) before you dial an outside number, do not press the access code either.

If the dial tone stops, you have touch-toneservice. LeaveT/P set to

T.

If the dial tone continues, you have pulse service. Set T/P toP.

SETUP

Note: If you do not press any key within 30 seconds after the language selection display appears, theET-1105exits the language selection display without changing the current selection.

2.To select another language, repeatedly press #/until you see the desired language.

#/

3.Press SETUP to store the selected language.

11

43-1105.fmPage 12 Monday, August 30, 1999 1:57 PM

SETTING THE AREA CODE

When you return a call from a Caller ID record (see “Dialing Numbers from a Caller ID Record” on Page 21), your phone automatically dials 1, the area code, and the number. The ET-1105lets you store one local area code and three neighborhood area codes. If the number you call has the same area code with your local area code, theET-1105dials the7-digitlocal number. If the number you call has the same area code with one of three neighborhood area codes, theET-1105dials the10-digitlocal number.

Follow these steps to set area codes.

Note: If you make a mistake or do not press a key within 10 seconds during these steps, start again at Step 1.

1.Pres SETUP. The language selection display appears.

2.Press /. The currently entered area codes (orAREACODE=000 000/000/000) appear.

SETTING THE RINGER

Turning the Ringer On or Off

You can turn the ET-1105’sringer on and off. SetRINGER on the side of the handset toON to hear an incoming call or a page from the base. SetRINGER toOFF to silence the ringer.

Note: With the ringer off, you can still make or receive calls using this cordless phone. Telephones on the same line still ring when there is an incoming call, and the IN USE indicator on theET-1105’sbase flashes until you answer the call.

RINGER

/

3.Enter your local area code first, then the three neighborhood area codes, then press SETUP to store them.

12

Checking/Setting the Ringer

You can set the ET-1105’shandset to sound any of three ringer types. The handset is preset to use the ringer tone (1). To change or hear the different tones, pressFLASH when the phone is not in use.PROG. RINGER displays. WithRINGER set toON, press1,2, or3, then pressFLASH to confirm the setting. (The last number button you pressed is the tone you will hear.)

43-1105.fmPage 13 Monday, August 30, 1999 1:57 PM

USING A HEADSET

You can make or answer calls with hands-freeconvenience using an optional headset that has a3/32-inch(2.5 mm) plug. We recommend RadioShack Cat. No.43-195,which is specially designed for use with theET-1105.

Follow these steps to use a headset.

1.Insert the headset’s plug into the jack on the top of the handset.

2.Place the headset on your head with the earpiece over either ear and adjust the microphone boom until it is about even with your chin.

3.Hang the belt clip on your belt.

4.Make or receive calls as you would normally (see “Making and Receiving a Call” on Page 14).

Notes:

Connecting a headset disconnects the handset’s earpiece and microphone.

If you place the handset on the base to recharge it while the headset is connected, be sure the handset seats properly.

REMOVING THE BELT CLIP

The belt clip on the back of the handset lets you hang the handset on your belt for easy portability. But to use the hanging hole on the back of the handset to place the handset on the wall-mountedbaseface-up,you must remove the belt clip.

Insert a flat-bladescrewdriver into either side of the belt clip, then pull it off.

To replace the belt clip, insert either tab of the belt clip into one of the handset’s slots, then snap the other tab into handset’s other slot.

13

43-1105.fmPage 14 Monday, August 30, 1999 1:57 PM

TELEPHONE OPERATION

MAKING AND RECEIVING A CALL

To make a call, lift the handset and press TALK.PHONE displays. When the TALK indicator lights steadily and you hear the dial tone, dial the desired phone number or memory number (see “Memory Dialing” on Page 15).

The ET-1105displays the phone number as you dial. ThenPHONE disappears, the duration of your call (after 14 seconds) in minutes and seconds displays.

To answer a call if the handset is on the base, lift the handset and press TALK. Or, if the handset is away from the base, press any key on the handset before speaking. The TALK indicator on the handset lights and the IN USE indicator on the base flashes.

To end a call, place the handset on the base or press TALK. The TALK and IN USE indicators turn off.

Notes:

If you press TALK to hang up and the phone does not disconnect, move closer to the base then pressTALK again, or place the handset on the base.

If you hear loud static during a conversation, move the handset closer to the base.

OUT OF RANGE appears when the distance from the handset to the base is out of the phone’s range.

SETTING THE HANDSET’S VOLUME

You can select any of four different volume settings by repeatedly pressing VOLUME during a call.

VOLUME

USING REDIAL

You can quickly redial the last number dialed. Lift the handset and press TALK. When you hear the dial tone, pressREDIAL. The number appears on the display as the phone dials it.

REDIAL

Notes:

The redial memory holds up to 32 digits, so you can redial longdistance as well as local numbers.

14

43-1105.fmPage 15 Monday, August 30, 1999 1:57 PM

We recommend you not use REDIAL to dial numbers that include a tone entry. This could result in a wrong number being dialed. (See “Using Tone Services on a Pulse Line.”)

The redial memory does not store a flash entry or any digits entered after you press FLASH (see “Using Flash”).

3.When the service answers, press

. appears. Any additional num-

bers you dial are sent as tone signals.

4.After you complete the call, return the handset to the base or press TALK. The phone automatically resets to pulse dialing.

USING FLASH

FLASH performs the electronic equivalent of a switchhook operation for special services, such as Call Waiting.

For example, if you have Call Waiting, press FLASH to answer an incoming call without disconnecting the current call. PressFLASH again to return to the first call.

Note: If you do not have any special phone services, pressingFLASH might disconnect the current call.

USING TONE SERVICES ON A PULSE LINE

Some special services, such as bank-by-phone, require tone signals. If you have pulse service, you can still use these special tone services by following these steps.

1.Be sure T/P is set toP.

2.Press TALK and dial the service’s main number.

USING PAGE

To page the person who has the handset or to locate the handset when the phone is not in use, press PAGE on the base. The handset beeps twice per second for 15 seconds andPAGING appears. The MESSAGE indicator flashes while the handset beeps.

PAGE

To stop the handset from beeping before it automatically stops, press any key on the handset or PAGE on the base.

Note: You cannot page the handset during a call.

MEMORY DIALING

You can store up to 20 phone numbers in memory, then dial a stored number by pressing a two-digitmemory location number.

15

43-1105.fmPage 16 Monday, August 30, 1999 1:57 PM

Each stored number can be up to 16 digits long.

Storing a Number in Memory

Notes:

If T/P is set toP and you want to use tone dialing for a memory number, you must store aas the first entry of the number you want to tone dial.

Do not store a number with both pulse and tone entries in the same memory location. This could result in a wrong number being dialed.

Each pause and tone entry ( ) uses one digit of memory.

To keep your accounts secure, we recommend you do not store your personal access code for services such as bank-by-phonein a memory location.

An error tone sounds and the phone exits the programming mode if you wait more than 30 seconds between each keypress or enter more than 16 digits. You must start over at Step 1.

1. Press MEM. MEMORY STORE

appears.

MEM

2.Enter the number you want to store. The number appears on the display.

16

If you enter an incorrect digit, start from Step 1, then re-enterthe correct digit.

3.Press MEM.ENTER 01-20 appears.

4.Enter a two-digitmemory location number between 05 and 20(01–04are reserved for your VIP Call List). TheET-1105beeps twice, and the display becomes blank.

5.To keep a record of each stored number, use a flat-bladescrewdriver to lift the plastic cover from the telephone number index card. Write the name on the index card.

Note: If you receive a call while you are storing information in memory, pressTALK to answer the call. After the call, begin again at Step 1.

To replace a stored number, store a new one in its place.

Using the VIP Call List

Your phone lets you save 4 phone numbers in the memory location numbers 01–04as its VIP Call List. Whenever someone calls from one of those 4 numbers, if you subscribe to Caller ID, the system sounds distinctive rings after the first ring to alert you. VIP displays when you recall the phone numbers (see “Recalling Numbers Stored in Memory” on Page 17).

43-1105.fmPage 17 Monday, August 30, 1999 1:57 PM

Entering a Pause

In some telephone systems, you must dial an access code (9, for example) and wait for a second dial tone before you can dial an outside number. You can store the access code with the phone number. However, you should also store a pause after the access code to allow the outside line time to connect. To do so, press REDIAL to enter a2-secondpause after entering the access code.P appears. For a longer pause, pressREDIAL again.

Recalling Numbers Stored in

Memory

1.Press CALL ID, then press #/.

TOTAL MEM=xx displays.

Dialing a Memory Number

1.Press TALK. The TALK indicator lights.

2.When you hear the dial tone, press MEM then enter the2-digitmemory location number. TheET-1105automatically dials the displayed phone number.

Or, follow Step 2 in “Recalling Numbers Stored in Memory” on Page 17 to recall the desired phone number. Then press

CALLBACK.

CALLBACK

#/

Note: If no phone number is stored,MEM EMPTY displays.

2.Repeatedly press REVIEW ▲ or ▼ until the desired number appears.

Chain-DialingService Numbers

For quick recall of numbers for special services (such as alternate long distance or bank by phone), store each group of numbers in its own memory location.

When calling special services, dial the service’s main number first. Then, at the appropriate place in the call, press MEM and enter the number for the location where the additional information is stored.

17

43-1105.fmPage 18 Monday, August 30, 1999 1:57 PM

Testing Stored Emergency

Numbers

If you store an emergency service’s number (police department, fire department, ambulance) and you choose to test the stored number, make the test call during the late evening or early morning hours to avoid peak demand periods. Remain on the line to explain the reason for your call.

Deleting Information in a Single

Memory Location

1.Recall the memory location containing the information you want to delete.

2.Press DELETE.DELETE ? appears.

Deleting Information in All

Memory Locations

1.Press CALL ID, then press #/.

TOTAL MEM=xx displays.

2.Press DELETE.DELETE ALL ? appears.

3.Press DELETE again to confirm deletion.DELETE OK appears.

To exit without deleting all of the memory location information, wait 10 seconds without pressing any button.

DELETE

3.Press DELETE again to confirm deletion. The previous memory location number and the number stored there appear.

To exit without deleting the information, wait 10 seconds without pressing any button.

18

43-1105.fmPage 19 Monday, August 30, 1999 1:57 PM

CALLER ID OPERATION

If you subscribe to Caller ID service from your phone company, the ET-1105automatically displays the information the phone company sends, along with the date and time the call was received, between the first and second rings of every call you receive. It stores up to 45 number only or name and number call records in its Caller ID memory.

The display also shows if caller information is not available or if the number is blocked by the sender (see “Caller ID Displays” on Page 20).

The IN USE indicator flashes on the base during an incoming call, RING appears briefly, the call record andNEW appear for 10 seconds, then the display blanks out.

If you subscribe to your phone company’s message waiting service, your system informs you when you have a message waiting. If the IN USE and MESSAGE indicators on the base flash (or appears after you pressTALK orCALL ID on the handset), you have a voice message in your mailbox. The IN USE and MESSAGE indicators flash (orappears after you pressTALK orCALL ID on the handset) until you retrieve the message.

If you subscribe to Call Waiting, the MESSAGE indicator lights on the base during a call. The Caller ID record appears. If you want to answer the incoming call, press FLASH. To resume the previous phone conversation, press FLASHagain.

REDIAL

19

43-1105.fmPage 20 Monday, August 30, 1999 1:57 PM

CALLER ID DISPLAYS

English

 

Display — French

Description

Spanish

 

 

 

 

 

xx NEW CID

The first line indicates the number of new calls. The sec-

TOTAL CID= xx

ond line shows the total number of Caller ID records in

NOUV IDAP

memory.

TOUT IDAP=xx

 

NUEV. ID.

 

TOTAL ID.=xx

 

 

 

ERROR

Appears when the Caller ID information was garbled, or if

ERREUR

there was an error during the transmission.

ERROR

 

 

 

PRIVATE

Appears if the caller chose to block sending Caller ID in-

PRIVÉ

formation. No caller information appears.

PRIVADO

 

 

 

UNAVAILABLE

Appears if the caller is not within a Caller ID service area,

NON DISPON.

or during operator-assistedcalls or calls made with a

NO DISPON.

credit card.

 

 

END OF LIST

Appears when you reach the end of your call records.

FIN DE LISTE

 

FIN DE LISTA

 

 

 

NO CID MSG

Appears when there are no Caller ID records in memory.

PAS DE MESSIDAP

 

NING MENS ID

 

 

 

R#xx

Appears when you review a Caller ID record from some-

 

one who has called more than one time from the same

 

number.

 

 

20