Radio Shack 63-996 User Manual

www.radioshack.com™

OWNER’S MANUAL —

Please read before using this equipment.

,WODQ/&KIKV"#VQOKE"9CNN"%NQEM

YKVJ"9KTGNGUU"+P11WV"6JGTOQOGVGT

63-996

ôýappears here if the clock		CHANNEL — Press to see the temperature
batteries are weak.		read by each thermo-sensor.	Thermo-sensor Channel
Signal Indicator				Monitor outdoor and indoor
		Extra-Large LCD — Easy to read
				temperature with the supplied
100 Feet (30 meters) Range		from the across the room.		thermo-sensor. You can use up to
				three thermo-sensors to monitor the
		Thermo-sensor Temperature		temperature of three different
Four Time Zones — View				locations.
		Remote thermo-sensor
Pacific, Mountain, Central,
		temperature and channel
and Eastern time zones.
				Low Battery Indicator — ôý
		x — Shows the temperature		appears if the batteries are weak.
Indoor Temperature		trend in the last half hour.
		ôýappears here if the sensor batteries are weak.		LED Display — Blinks when
				the thermosensor is in normal
Alarm Indicator		Current day of the week		working condition.
	Alarm Time

ZONE — Press ZONE until the desired time zone appears. Hold down ZONE for three seconds until ø disappears to turn off automatic time setting if you move to an area where a signal is unavailable.

H — Press while setting the time or alarm		THERMO — Hold down THERMO and CHANNEL
time to advance to the next digit to set. Hold
down H for a few seconds until ø appears to		at the same time for about two seconds to search
turn on automatic time setting mode.		for the signal from the thermosensor.
CLOCK — Press to toggle the alarm time display		ALARM — Hold down to enter alarm setting
		mode. When in alarm setting mode, press to
between seconds and day of the week. Hold down to
		set the alarm time hour and minutes.
enter manual time setting mode. When in time setting
mode, press CLOCK to set the hour, minutes, year,
month, date, and language. The year can be set from
2000 – 2099. Manual setting is overidden by the
automatic setting (radio signal) from the atomic clock.
		RESET — If the clock stops operating or
‘AA’ UM3 1.5V	‘AA’ UM3 1.5V	locks up, you can reset it. Press RESET with
		a pointed object. The clock starts scanning
		for a radio signal.
Battery Compartment
		Built-In Stand

."%#76+10".

Battery Installation

•Use only fresh batteries of the required size and type.

•Do not mix old and new batteries, different types of batteries (standard, alkaline, or rechargeable), or rechargeable batteries of different capacities.

Mounting

•Do not place your clock or thermo-sensor in direct sunlight, near electronic appliances, or in a location where it is likely to get wet.

±"016'"±"

•If the clock does not operate after you install the batteries, remove them and wait about five seconds until the display clears. Then reinstall the batteries.

•Remove the protective film from the clock display before use.

Thank you for purchasing the RadioShack Jumbo-Digit Atomic Wall Clock with Wireless In/Out Thermometer. Your clock is a multifunctional radio frequency (RF) controlled clock designed to automatically synchronize the current time and date when brought within range of the radio signal from the U.S. Atomic clock. After you install the batteries, the clock automatically searches for a radio signal.

$#66'4;"+056#..#6+10

You need two AA alkaline batteries for the clock and two AA alkaline batteries for the thermo-sensor (not supplied ). When ô appears, replace the batteries. For the best performance and longest life we recommend RadioShack alkaline batteries. .#±

+0"6*'"6*'4/1/5'0514

1.Remove the holder from the back of the thermo-sensor.

2.Use a Phillips screwdriver to remove the screws on the battery compartment cover, then slide off the cover.

2.°C/°F — Set to °C

1. CHANNEL 1/2/3 — The	for Celsius or to °F
	for Fahrenheit
clock can display	temperature
information for up to three	readings.
different thermo-sensors.
Slide CHANNEL1/2/3	3. RESET — Use a
inside each remote	pointed object to
sensor’s battery	press RESET and
compartment to a different	initializethesensor’s
setting.	transmitter.

3.Place the batteries in the compartment as indicated by the polarity symbols (+ and –) marked inside.

4.Replace the battery cover and secure it with the screws.

+0"6*'"%.1%-

1.Pull the tab on the battery compartment cover at the back of the clock to remove the cover.

2.Place the batteries in the compartment as indicated by the polarity symbols (+ and –) mark inside.

3.Replace the cover.

/1706+0)

Place the clock and thermo-sensor on a flat surface using the stand, or mount it on a wall using screws (not supplied). .

6*'"%.1%-

1P"C"(NCV"5WTHCEG

Pull the built-in stand away from the back of the clock and set it on a table or other flat surface.

1P"C"9CNN

1.Use a 1/8 inch screw (not supplied) with a head that fits into the keyhole slot on the back of the clock to drill a hole in the wall at the desired mounting location.

2.Thread the screw into the wall until the head extends about ¼ inch from the wall.

3.Position the keyhole slot over the screw and slide the thermometer down to secure it.

6*'"6*'4/1/5'0514

1P"C"(NCV"5WTHCEG

Insert the ends of the supplied wire stand into the holes on the back of the thermo-sensor and set it on a table or other flat surface.

1P"C"9CNN

1.Use two 1/8-inch screws (not supplied) with heads that fit into the keyhole slots on the back of the supplied mounting bracket to drill two holes about 13/4 inches apart on the mounting surface.

2.Thread a screw into each hole so the heads extend about ¼ inch from the mounting surface.

3.Align the keyhole slots on the mounting bracket with the screws and slide the bracket downward to secure it.

4.Slide the remote sensor onto the mounting bracket.

#"+/2146#06"#

If an icon appears at the end of a paragraph, go to the box on that page with the corresponding icon for pertinentý information.

R— Warning # — Important ±— Note .— Caution ° — Hint

© 2002 RadioShack Corporation.

All Rights Reserved.

RadioShack and RadioShack.com are trademarks used by RadioShack Corporation.