Radio Shack 63-969 User Manual

Size:
826.55 Kb
Download

63-969.fmPage 1 Monday, September 27, 1999 9:19 AM

Cat. No. 63-969

OWNER’S MANUAL

Please read before using this equipment.

Projection Clock

63-969.fmPage 2 Monday, September 27, 1999 9:19 AM

FEATURES

Your RadioShack Projection Clock combines a simple design with advanced technology. You can set the clock so it projects the current time on a wall or the ceiling for easy nighttime viewing. Its features include:

Adjustable Projection Light — lets you project the time on any location on a wall or ceiling. This lets you easily see the time at night.

Large Liquid Crystal Display — makes the clock easy to read. The current time and alarm time, the time zone you are in, and the date and day of the week appear on the display.

Crescendo Alarm — the alarm sounds a series of beeps that gradually increase in volume.

Snooze Control — temporarily silences the alarm for about 8 minutes so you can sleep a little longer.

Display Backlight — lets you see all information on the display even when it is dark.

Supplied AC Adapter — lets you power the clock’s projection light to help extend battery life.

Three Languages — let you view the day of the week in English, French, or Spanish.

© 1999 Tandy Corporation.

All Rights Reserved.

RadioShack is a registered trademark used by Tandy Corporation.

2

63-969.fmPage 3 Monday, September 27, 1999 9:19 AM

Three Languages — let you view the day of the week in English, French, or Spanish.

WARNING: To reduce the risk of fire or shock hazard, do not expose this product to rain or moisture.

 

CAUTION

!

 

RISK OF ELECTRIC SHOCK. DO NOT

 

OPEN.

 

 

 

 

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER OR BACK. NOUSER-SERVICE-ABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.

This symbol is intended to alert you to the presence of uninsulated dangerous voltage within the product’s enclosure that might be of sufficient magnitude to constitute a risk of electric shock. Do not open the product’s case.

This symbol is intended to inform you that impor-

!included in the literature accompanying this prod- uct.tant operating and maintenance instructions are

Note: You need the supplied AC adapter and two AA batteries (not supplied) to power the projection light.

3

63-969.fmPage 4 Monday, September 27, 1999 9:19 AM

PREPARATION

INSTALLING BATTERIES

Your clock requires two AA batteries (not supplied) for power. For the best performance and longest life, we recommend RadioShack alkaline batteries.

Cautions:

Use only fresh batteries of the required size and recommended type.

Do not mix old and new batteries, different types of batteries (standard, alkaline, or rechargeable), or rechargeable batteries of different capacities.

Follow these steps to install batteries.

1.Slide the battery compartment cover in the direction of the arrow to remove it.

2.Place the batteries in the compartment as indicated by the polarity symbols (+ and –)marked inside.

4

63-969.fmPage 5 Monday, September 27, 1999 9:19 AM

When you install batteries, all display segments briefly appear. Then AM 12:00 appears, followed by the seconds display.1 appears belowMONTH and1 appears belowDATE, indicating January 1.P (the default time zone) appears above the zone indicator.

Note: The clock is preset to display the day of the week in English. To set the clock to display in another language, see “Setting the Clock” on Page 7.

3. Replace the cover.

When BATT appears or the clock stops operating properly, replace the batteries.

Warning: Dispose of old batteries promptly and properly. Do not burn or bury them.

Caution: If you do not plan to use the clock for a month or more, remove the batteries. Batteries can leak chemicals that can destroy electronic parts.

CONNECTING TO AC POWER

Your clock comes with an AC adapter so you can operate the clock’s projector light continuously from AC power.

5

63-969.fmPage 6 Monday, September 27, 1999 9:19 AM

Caution: You must use a Class 2 power source

!that supplies 3 volts DC and delivers at least 200 mA. Its center tip must be set to positive

and its plug must fit the clock's DC 3V jack. The supplied adapter meets these specifications. Using an adapter that does not meet these specifications could damage the clock or the adapter.

Follow these steps to connect the AC adapter to the clock.

1.Slide the battery compartment cover in the direction of the arrow to remove it.

2.Plug the AC adapter’s tip into the jack inside the battery compartment.

3.Route the adapter’s cord through the slot marked DC 3V on the back of the clock.

4.Replace the cover.

5.Plug the AC adapter’s other end into a standard AC outlet.

6

63-969.fmPage 7 Monday, September 27, 1999 9:19 AM

SETTING THE CLOCK

1.Repeatedly press ZONE to select the time zone you are in (Pacific, Mountain, Central, or Eastern). As you pressZONE, the time zone you select is highlighted and a letter (P for Pacific,M for Mountain,C for Central, orE for Eastern) appears above the zone indicator.

2.Hold down MODE/SET until the hour digit flashes.

3.Repeatedly press +. The hour advances by 1 with each press. (Hold down+ to rapidly advance the hour).

Note: AM appears for AM hours andPM appears for PM hours.

4.Press MODE/SET. The minute digits flash.

5.Hold down or repeatedly press + to set the minute.

6.Press MODE/SET. The year digits flash.

7.Repeatedly press + to set the year.

8.Press MODE/SET. The current hour, minute, and day of the week appear, and the month digit flashes.

9.Hold down or repeatedly press + to set the month.

10.Press MODE/SET. The date digit flashes.

11.Repeatedly press + to set the date.

7

63-969.fmPage 8 Monday, September 27, 1999 9:19 AM

12.Press MODE/SET. A letter representing the language used for the day of the week (E for English,F for French, orS for Spanish) appears.

13.Repeatedly press + to select the desired language.

14.Press MODE/SET. The time, time zone, and date settings appear.

8

63-969.fmPage 9 Monday, September 27, 1999 9:19 AM

OPERATION

To switch between viewing the seconds display and the day of the week, press MODE/SET. To switch between viewing the month/date and the alarm time, press ALARM STOP/ALARM SET.

To view the time in another time zone, repeatedly press ZONE to highlight the zone you want. The time in that time zone appears.

To light the display for about 5 seconds, press SNOOZE/ LIGHT.

USING THE PROJECTION LIGHT

You can use the clock’s projection light to project the time on a wall or ceiling.

To project the time, place the clock at least 18 inches from the surface you are projecting onto, adjust the projection arm to project light onto the surface where you want to see the time, then slide PROJECTION LIGHT ON on the back of the clock in the direction of the arrow.

Projection Arm

PROJECTION

 

 

LIGHT ON

9

63-969.fmPage 10 Monday, September 27, 1999 9:19 AM

Caution: The projection arm moves about 90 degrees in either direction. Do not force it.

To focus the time on the desired position, adjust FOCUS on the side of the projection arm.

To turn off the projection light, slide PROJECTION LIGHT ON toward the projection arm.

With the projection light off, you can also project the time by pressing SNOOZE/LIGHT. The projector lights for about 5 seconds then automatically turns off.

USING THE ALARM

Setting the Alarm Time

Note: If you do not press a button within about 90 seconds after you pressed the previous button, the clock exits its alarm setup mode. Start over at Step 1.

1.Hold down ALARM STOP/ALARM SET until the alarm time andappear. The hour digit flashes.

2.Hold down or repeatedly press +.appears and the alarm hour advances by 1 with each press.

10