Radio Shack 43-683 User Manual

Size:
458.82 Kb
Download

;22"/*\"#PCNQI"4/.KPG"%QTFNGUU"2JQPG

YKVJ"%+&1"&WCN"-G[RCF1"5RGCMGTRJQPG

43-683B

OWNER’S MANUAL — Please read before using this equipment.

 

 

%106'065

Important Caller ID

 

Information .....................................

2

Important Safety Instructions .........

3

Battery Safety Instructions ..........

5

Installation ......................................

5

Connecting to Phone Lines ........

6

On a Desk Top ............................

6

On a Wall or Wall Plate ...............

7

Connecting and Charging

 

the Battery Pack .........................

8

Setting the Dialing Mode ................

9

Adjusting the Ringer .....................

10

On the Handset ........................

10

On the Base ..............................

10

Setting Auto Talk ..........................

10

Setting Caller ID/Call Waiting .......

10

Storing Your Area Code ................

11

Selecting a Language ...................

11

Using the Handset .......................

12

Making a Call ............................

12

Answering a Call .......................

12

Selecting the Channel ...........

12

Setting the Handset

 

Volume..................................

12

Using the Speakerphone .............

13

Making a Call ............................

13

Answering a Call .......................

13

Adjusting the Speakerphone

 

Volume..................................

13

Using Mute ...............................

13

Putting a Call On Hold .................

14

Switching Between the Handset and

Speakerphone ..............................

14

Using Both the Handset and

 

Speakerphone ..............................

14

Using a Headset ..........................

15

Making a Conference Call ............

15

3-Way Conferencing .................

15

4-Way Conferencing .................

16

Extension Phones ........................

16

Using Redial .................................

16

Using Flash ..................................

17

Tone Services On a Pulse Line ....

17

Using the Paging/Intercom

 

Features .......................................

17

Memory Dialing ............................

18

Storing a Number in Memory ....

18

(Continued)

Two-LineTelephone System —lets you easily handle two telephone lines at the same time. You can use both lines to make 3- or 4- way conference calls, or one line for data communication while you are talking on the other.

Speakerphone — lets you make or answer calls without using the handset.

Dual Keypads — a full set of keys on both the phone's handset and base let you use either keypad to make and answer calls or use the phone's features.

Thank you for purchasing a RadioShack 900 MHz 2 Line Cordless Speakerphone. It uses advanced cordless telephone technology to give you superior audio quality and extended range. It is designed to exacting standards that ensure reliability, long life, and outstanding performance.

The phone’s Caller ID memory records and stores up to 80 Caller ID records (40 for each line), including telephone number (and name, if available in your area) and the date and time of the call, as provided by your local phone company to Caller ID service subscribers. If you subscribe to Call Waiting with Caller ID, the phone can show you the incoming caller information, even when you are already on the phone.

© 2002 RadioShack Corporation.

All Rights Reserved.

RadioShack and RadioShack.com are trademarks used by RadioShack Corporation.

Information ID Caller Important

%106'065

(Continued)

 

In the Handset.......................

18

Editing or Deleting a Number in

the Handset's Memory ..........

19

In the Base............................

20

Entering a Pause ......................

20

Testing Stored Emergency

 

Numbers ...................................

21

Reviewing Memory Numbers

 

(Handset Only) .........................

21

Dialing a Memory Number ........

21

Chain-Dialing Service

 

Numbers ...................................

21

Caller ID Operation

 

(Handset Only) .............................

22

Reviewing Caller ID Records ....

22

Caller ID Messages ..................

23

Adding/Deleting the

 

Area Code ................................

23

Dialing Numbers from a Caller ID

 

Record ......................................

23

Storing a Caller ID Record

 

to Memory .................................

24

Deleting Caller ID Records .......

24

Troubleshooting ...........................

24

Care .............................................

26

Service and Repair ......................

26

FCC Statement ............................

27

Lightning ...................................

28

As an ENERGYSTAR Partner, RadioShack Corporation has determined that this product meets the ENERGYSTAR

WARNING: To reduce the risk of fire or shock

 

..CAUTION..

 

!

RISK OF ELECTRIC SHOCK

 

DO NOT OPEN

 

 

 

 

 

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER OR BACK. NOUSER-SERVICEABLEPARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.

The lightning symbol is intended to alert you to the presence of uninsulated dangerous voltage within this product’s enclosure that might be of sufficient magnitude to constitute a risk of electric shock. Do not open the product’s case.

The exclamation symbol is intended to inform you that important operating and maintenance

!instructions are included in the literature accompanying this product.

3-LineLiquid Crystal Display— lets you view an entire Caller ID record on one screen.

40-Number Memory Dialing — lets you store up to 40 numbers in memory (30 on the handset and ten on the base) for easy dialing. (See “Memory Dialing” on Page 18.)

Paging/Two-WayIntercom System— lets you send a signal from the base to the handset, or from the handset to the base, to page someone or locate the handset when it is away from the base. If someone answers, you can use the phone as an intercom. (See “Using the Paging/Intercom Features” on Page 17.)

Face-downorFace-upHandset Charging— you can place the handset on the base face-down or face-up.

Ample Talk and Standby Time — the supplied battery pack provides 7 hours of continuous talk time or 14 days of standby time (when fully charged).

Headset Jack — lets you make or answer calls with handsfree convenience using an optional headset. (See “Using a Headset” on Page 15.)

Auto Talk — you can set the phone so you can answer a call by just lifting the handset from the base. (See “Setting Auto Talk” on Page 10.)

Any Key Answer — you can set the phone so you can press any key to answer a call when the handset is away from the base.

+/2146#06"%#..'4"+&" +0(14/#6+10

To use the phone’s Caller ID and Call Waiting with Caller ID features, you must be in an area where those services are available and you must subscribe to those services through your local phone company. Where Caller ID is offered, one or more options are generally available:

caller's number only

caller's name only

caller's name and number.

2

+/2146#06"5#('6;" +05647%6+105

When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:

1.Read and understand all instructions.

2.Follow all warnings and instructions marked on the product.

3.Never install telephone wiring during a lightning storm.

4.Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.

5.Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.

6.Use caution when installing or modifying telephone lines.

7.Do not fix the AC power supply cord to building surfaces with metal fittings (If the product has an AC power cord).

8.Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

9.Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool.

10.Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious damage to the product.

11.Slots and openings in the cabinet and the back or bottom are provided for ventilation. To protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register. This product should not be placed in a built-ininstallation unless proper ventilation is provided.

#"+/2146#06"#

If an icon appears at the end of a paragraph, go to the box on that page with the corresponding icon for pertinent information.

R— Warning

# — Important

.— Caution

° — Hint

± — Note

 

Important Safety Instructions

3

Instructions Safety Important

12.This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your local power company.

13.Do not allow anything to rest on the power cord. Do not locate this product where the cord will be stepped on.

14.Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.

15.Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on the product.

16.To reduce the risk of electric shock, do not disassemble this product. Take it to a qualified serviceman when service or repair work is required. Opening or removing covers may expose you to dangerous voltage or other risks. Incorrect reassembly can cause electric shock when the product is subsequently used.

17.Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

When the power cord plug is damaged or frayed.

If liquid has been spilled into the product.

If the product has been exposed to rain or water.

If the product does not operate normally by following the operating instructions.

Adjust only those controls that are covered by the operating instructions because improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation.

If the product has been dropped or the cabinet has been damaged.

If the product exhibits a distinct change in performance.

18.Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.

4

19.Do not use the telephone to report a gas leak in the vicinity of the leak.

$#66'4;"5#('6;"+05647%6+105.

1.Use only the appropriate type and size of battery pack specified in the instruction manual provided for this product.

2.Do not dispose of the battery pack in a fire. The cell may explode. Check with local codes for possible special disposal instructions.

3.Do not open or mutilate the battery pack. Released electrolyte is corrosive and may cause damage to the eyes or skin. It may be toxic if swallowed.

4.Exercise care in handling the battery pack in order not to short it with conducting materials such as rings, bracelets, and keys. The battery or conductor may overheat and cause burns.

5.Charge the battery pack provided with or identified for use with this product only in accordance with the instructions and limitations specified in this owner’s manual.

6.Observe proper polarity orientation between the battery pack and the battery charger.

5#8'"6*'5'"+05647%6+105

+056#..#6+10

You can place the phone’s base on a desk or table, or mount it on a standard wall plate or directly on a wall. Choose a location that is:

near an AC outlet

near a modular telephone line jack

out of the way of normal activities

away from electrical machinery, electrical appliances, metal walls or filing cabinets, wireless intercoms, alarms, and room monitors

away from other cordless phones

The base’s location affects the handset’s range. If you have a choice of several locations, try each to see which provides the best performance.

."%#76+10".

TO REDUCE THE RISK OF FIRE OR INJURY, READ AND FOLLOW THE INSTRUCTIONS.

Installation

5

Installation

±"016'"±"

Connecting to Phone Lines

The line that connects a two-linephone jack to the phone company wiring must betwisted-paircable. Otherwise, you might hear interference (crosstalk) between the two lines.

The USOC number of the twoline jack to be installed is RJ14C (RJ14W for a wall-plate).The USOC number of asingle-linejack is RJ11C.

On a Desk Top

If you connect the phone to a two-linephone jack with a twoline cord, do not connect a cord to theTEL LINE 2 jack or the phone will not operate properly. Instead, you can connect another phone device, such as a fax machine or modem.

If you connect the phone to a single one-linephone jack, avoid pressing the unused line button or you might hear feedback.

."%#76+10".

You must use a Class 2

!power source that supplies 9V AC and delivers at least

350 mA. Its center tip must be set to positive and its plug must fit the phone's DC IN 9V jack. The supplied adapter meets these specifications. Using an adapter that does not meet these specifications could damage the phone or the adapter.

Always connect the AC adapter to the phone before you connect it to AC power. When you finish, disconnect the adapter from AC power before you disconnect it from the phone.

%100'%6+0)"61"2*10'".+0'5

To take full advantage of the phone’s capabilities, you must have two phone lines with separate phone numbers. If you have only one line, you can order a second from your phone company.

You can connect the phone to the lines in one of three ways:

connect two lines through a two-linemodular phone jack

connect two lines through two one-linemodular phone jacks

connect one line through a one-linemodular phone jack.

Your telephone connects directly to a modular telephone line jack. If your telephone wiring does not have a modular jack, you can update the wiring yourself using jacks and adapters (available at your local RadioShack store or online at RadioShack.com), or have the telephone company update the wiring for you. You must use compatible modular jacks that are compliant with Part 68 of FCC Rules

10"#"&'5-"612

1.To connect the phone to a two-linephone jack, plug

one end of the supplied long two-linemodular cord into theTEL LINE 1/2 jack on the back of the phone. ±

To connect the phone to two one-linephone jacks, plug one end of the supplied long two-line modular cord into TEL LINE 1/2 and plug another cord (not supplied) into the TEL LINE 2 jack.

To connect the phone to a single one-linephone jack,

plug one end of the supplied long modular cord into the

TEL LINE 1/2 or TEL LINE 2jack.±

2.Plug the supplied AC adapter’s barrel plug into the DC IN 9V jack on the back of the base..

3.Route the adapter’s cord through the strain relief slot on the bottom of the bracket.

4.Plug the adapter into a standard AC outlet.

5.Connect the phone cord(s) to the modular phone line jack(s).

6.Lift the base’s antenna to a vertical position.

6

10"#"9#.."14"9#.."2.#6'

To mount the base directly on the wall, you need two screws (not supplied) with heads that fit into the keyhole slots on the bottom of the bracket. Drill two holes 315/16 inches apart. Then thread a screw into each hole, letting the heads extend about5/32 inch from the wall.

1. Insert the two tabs at the top of the narrow end of the supplied bracket into the base’s upper tab slots, then press down on the bracket's latches and insert them into the clip slots.

2.To connect the phone to a two-linephone jack, plug

one end of the supplied long modular cord into the TEL LINE 1/2 jack on the back of the phone.±

To connect the phone to two one-linephone jacks, plug one end of the supplied short two-line modular cord into TEL LINE 1/2 and plug another cord (not supplied) into the TEL LINE 2 jack.

To connect the phone to a single one-linephone jack, plug one end of the supplied long modular cord into the

TEL LINE 1/2 or TEL LINE 2jack.

3.Insert the supplied AC adapter’s barrel plug into the DC IN 9V jack on the back of the base.

4.Route the adapter’s

cord through the narrow groove on the bracket. If you are using two phone cords, route the second cord through one of the wide grooves on the bracket.

±"016'"±"

If you connect the phone to a twoline phone jack with a two-linecord, do not connect a cord to theTEL LINE 2 jack or the phone will not operate properly.

Installation

7

Installation

±"016'"±"

If the base loses power for 60 minutes while the handset is away from it, the security code might be lost. To reset the code, return the handset to the base for about five seconds.

Using a pencil eraser, clean the charging contacts on the handset and base about once a month.

If the battery pack becomes weak during a call, the handset beeps every three seconds and

Bemý8Wjj[ho flashes. When this happens, you cannot make a call until you recharge the battery pack.

About once a month, fully discharge the battery by

keeping the handset off the base until Bemý8Wjj[ho flashes. Otherwise, the battery pack loses its ability to fully recharge.

If the display is blank and the phone does not work, recharge the battery pack. (The battery power might be too low to light the display.)

If you are not going to use your phone for an extended period of time, disconnect the battery pack. This increases the battery pack's usable life.

5.To mount the phone on a wall

plate, plug the other end of the short modular cord into the

wall plate jack, then align the

bracket’s keyhole slots

with the wall plate studs and

slide the base

downward to secure it. If you are using two phone cords, plug the second cord into the second phone jack.

To mount the phone directly on a wall, align the bracket's keyhole slots with the mounted screws and slide the base downward to secure it. Connect the phone cord(s) to the modular phone line jack(s).

6.Plug the adapter into a standard AC outlet.

TEL LINE 2

DC IN 9V

TEL LINE 1 / 2

7.Press and lift out the handset holder, flip it over, then snap it back into place to hold the handset.

8.Raise the base’s antenna to a vertical position.

%100'%6+0)"#0&"%*#4)+0)"6*'" $#66'4;"2#%-

The phone comes with a rechargeable nickel-cadmium(NiCd) battery pack in the handset. Before using your phone, you must connect the battery pack, then charge it for about15–20hours.±

1.Press down and slide off the battery pack compartment cover.

2.Lift the battery pack out of the compartment.

8

3.Plug the battery pack’s connector into the socket in the compartment, (the connector fits only one way), replace the battery pack, and replace the cover.

To charge the battery pack, place the handset either faceup or face-downon the base.

The CHARGE indicator on the base lights and the number of new and total Caller ID records for each line appears on the handset's display. Be sure the battery pack is properly connected before you try to charge it. The CHARGE indicator lights when the handset is on the base even if the battery pack is not properly connected.

Recharge the battery pack when Bemý8Wjj[ho flashes.

When you first use the phone after charging or recharging the battery pack, the phone might not work and you might hear a beep when you press LINE 1 orLINE 2. Return the handset to the base for about five seconds to reset the securityaccess-protectioncode.

The supplied battery pack should last about a year. If the battery pack does not hold a charge for more than 2 hours after an overnight charge, replace it with a new 3.6-volt,600 mAh battery pack with a connector that fits the socket in the battery compartment.

You can order a replacement battery pack through RadioShack. Install the new battery pack and charge it for about 15–20hours.R

If you have trouble replacing the battery pack, take the phone to RadioShack for assistance.#

5'66+0)"6*'"&+#.+0)"/1&'

Your phone comes set for tone dialing. If you have pulse service, you must change the dialing mode. If you are not sure which type of service you have, do this test.

1.Press LINE 1 orLINE 2 and listen for a dial tone.

2.Press any number other than 0.±

If the dial tone stops, you have touch-toneservice. If the dial tone continues, you have pulse service.

To set the dialing mode, press the line button to hang up the phone if necessary. Hold down FLASH on the base keypad until the phone beeps, then press# for pulse dialing or* for tone dialing. The phone beeps.

R"9#40+0)ýRýR"

Dispose of the old battery pack promptly and properly. Do not burn or bury it (see “Battery Safety Instructions+” on Page 5).

#"+/2146#06"#

The EPA certified RBRC® Battery Recycling Seal on the nickel-cadmium(Ni-Cd)battery indicates RadioShack is voluntarily

participating in an industry program to collect and recycle these batteries at the end of their useful life, when taken out of service in the United States or Canada. The RBRC program provides a convenient alternative to placing used Ni-Cdbatteries into the trash or the municipal waste stream, which may be illegal in your area. Please call1-800-THE-SHACK(1-800-843-7422)for information onNi-Cdbattery recycling and disposal bans/restrictions in your area. RadioShack’s involvement in this program is part of the company’s commitment to preserving our environment and conserving our natural resources.

 

 

 

±"016'"±"

 

Mode

• If your phone system requires

 

 

Dialing

that you dial an access code (9,

 

 

 

for example) before you dial an

 

 

outside number, do not press

 

the

the access code either.

 

 

Setting

• The phone exits setting mode if

 

 

 

a call is received, or if you press

 

 

either line button.

 

 

 

 

 

9

LINE 1
LINE 2

Ringer the Adjusting

±"016'"±"

Auto Talk is set for each line separately. For example, when you turn Auto Talk on for Line 1 only, you must press LINE 2 to answer a call on line 2.

#&,756+0)"6*'"4+0)'4

The phone lets you control its base and handset ringer volume separately. You can choose from a high or low ringer setting for the base and the handset.

10"6*'"*#0&5'6"

At any time except during a call, press SELECT/VOLUME to

set the handset's ringer volume. The display shows H_d][hý >_]^ orH_d][hýBem.

10"6*'"$#5'

Set RING VOL on the back of the base toHI,LO, orOFF for each line (L1 and L2). WithRING VOL set toOFF, the base's ringer does not sound when a call is received, but the handset (and any other phone connected to the same line) still rings.

5'66+0)"#761"6#.-

Your phone is preset so you must press or to answer a call. With Auto Talk turned on, you can answer a call by lifting the handset from the base or pressing any number key on the base (or any key on the handset if the handset is away from the base).

1.To turn Auto Talk on or off, lift the handset and hold

down CALL ID/HOLD until the menu appears with the pointer at Line 1.±

2.Use 8/INTCM orCONF/9 to select Line 1 or Line 2. Then press#/7. A menu appears with7kjeýJWba selected.

3.Press SELECT/VOLUME to change the setting.Ed orE\\ appears indicating the selected setting.

4.Return the handset to the base.

5'66+0)"%#..'4"+&1%#.." 9#+6+0)

If you have Call Waiting and Caller ID service, you can set the phone to show Caller ID information for an incoming call even while you are already on the phone.ýCaller ID/Call Waiting is set separately for each line.

1.Lift the handset and hold down CALL ID/HOLD until the menu appears withB_d[ý' selected.

10

2.Use 8/INTCM orCONF/9 to select Line 1 or Line 2. Then press#/7.

3.A menu appears with 7kjeýJWba selected. PressCONF/9 to select9?:9M, then pressSELECT/VOLUME to change the setting.Ed orE\\ appears indicating the selected setting.

4.Return the handset to the base to store the new setting.

5614+0)";174"#4'#"%1&'

You can store your local area code in the phone’s Caller ID memory so it does not show the area code if the received call is from your local area. If you need to dial the area code (or store it in the memory), you can add it afterwards. See “Adding/Deleting the Area Code” on Page 23. ±

1.Lift the handset and hold down CALL ID/HOLD until the menu appears withB_d[ý' selected.

2.Use 8/INTCM orCONF/9 to selectB_d[ý' orB_d[ý(. Then press#/7. A menu appears with7kjeýJWba selected.

3.Press CONF/9 twice to select7h[Wý9eZ[, then press

SELECT/VOLUME.

4.Enter your 3-digitarea code using the number keys. If

you make a mistake, repeatedly press 6/* or#/7 to move the cursor over the incorrect digit, then enter the correct number.

5.Press SELECT/VOLUME to store the area code.

5'.'%6+0)"#".#0)7#)'

You can set the display’s language to English or French. To select the language:

1.Lift the handset and hold down CALL ID/HOLD until the menu appears withB_d[ý' selected.

2.Use 8/INTCM orCONF/9 to selectBWd]kW][1

3.Press SELECT/VOLUME to select;d] (English) or<h$ (French).

±"016'"±"

If your calling area requires 10digit dialing including area code, do not enter the area code but leave this option blank.

If an area code is already stored, it appears when you press SELECT/VOLUME. To delete the area code, pressDEL/FLASH three times.

Storing Your Area Code

11

Handset the Using

±"016'"±"

You can use the keypad on either the handset or the base to operate the phone. To make a call with the speakerphone, you must use the base’s keypad; to make a call with the handset, you must use the handset’s keypad.

If 8Wi[ appears above Line 1 or Line 2 on the display, someone is using that line at the base.

Press the other line button.

You can also enter the number before pressing LINE 1 orLINE 2. The entered number appears on the display. After confirming the number is

correct, press LINE 1 orLINE 2.

75+0)"6*'"*#0&5'6

/#-+0)"#"%#..

1.Lift the handset and press LINE 1 orLINE 2.B_d[ý' orB_d[ý( appears on the handset’s display and the same line’s indicator on the base flashes green.

2.Dial the number. Within a few seconds, the display starts to count the elapsed time.±

3.To end a call, press LINE 1 orLINE 2 on the handset or place the handset on the base.

#059'4+0)"#"%#..

When a call comes in, 9Wbb appears on the display, along withB_d[ý' orB_d[ý( (whichever is ringing). Then the display shows the caller’s name (if available) and number (if you subscribe to Caller ID), and the indicator for that line flashes at the base.ýTo help you tell which line is ringing, each line has a distinctive tone.

To answer a call, lift the handset and press the ringing line button. If Auto Talk is on, lift the handset from the base, or if the handset is away from the base, press any key. The display changes to show the elapsed time on the call.

If you receive a call on one line while you are using the handset to talk on the other, you hear a three-ringtone through the handset. Press the line button for the incoming call's line. The current call is automatically put on hold.

If both lines have an incoming call, pressing a key answers the line that began ringing first.

5GNGEVKPI"VJG"%JCPPGN

The phone has 20 channels. If a call disconnects for no reason, press CH on the handset to select a different channel.

5GVVKPI"VJG"*CPFUGV"8QNWOG

To increase or decrease the handset’s volume during a call, press SELECT/VOLUME. Each time you press the button, the

volume setting changes and the display shows the level as

Lebkc[ýBem, Lebkc[ýC[Z_kc, Lebkc[ý>_]^, or Lebkc[ýCWn_ckc.

12

RING VOL
LINE 1

75+0)"6*'"52'#-'42*10'

/#-+0)"#"%#..

To make a call using the speakerphone, press or LINE 2, listen for the dial tone, then dial the number. The

LINE 1 SPEAKER or LINE 2 SPEAKER indicator lights green on the base, and 8Wi[ andB_d[ý' orB_d[ý( appear on

the handset’s display as a reminder that the line is in use.

If either line indicator is flashing, someone at the handset is using the line. Press the line button for the line that is not in use.

To end a speakerphone call, simply press LINE 1 orLINE 2. The line indicator turns off.

#059'4+0)"#"%#..

To answer a call using the speakerphone, press LINE 1 or

LINE 2 (whichever is flashing), or any number key. The line indicator for the selected line lights.8Wi[ andB_d[ý' orB_d[ý(

appear on the handset's display as a reminder that the line is in use.

If you receive a call on a line while you are talking on the speakerphone on the other line, the other line’s indicator flashes and you hear a low ring if you have set for that line to any position other than OFF. Press the line button for the incoming call. The current call is automatically put on hold.

#FLWUVKPI"VJG"5RGCMGTRJQPG"8QNWOG

To set the speakerphone’s volume, slide VOLUME on the right side of the base.

75+0)"/76'

While talking on the speakerphone, you can temporarily turn off the phone’s microphone by pressing MUTE so the other party cannot hear you. The line indicator flashes red when a line is muted. PressMUTE again to resume your conversation.±

±"016'"±"

Mute is released when you press INTERCOM,HOLD, or press either line button to switch the line.

Using the Speakerphone

13

CALL ID/HOLD

Hold On Call a Putting

±"016'"±"

Putting a Call On Hold

Pressing HOLD(or CALL ID/ HOLD) again while a call is on hold does not release the hold. Press the line button that is on hold.

Using Both the Handset and Speakerphone

If you hear a high-pitchednoise from the base’s speaker, the handset and the base are too close together.

2766+0)"#"%#.."10"*1.&

To put a call on hold, press HOLD (CALL ID/HOLD on the handset). The indicator for that line lights red on the base, and the handset display shows>ebZýabove the line number. While a call is on hold, you can temporarily place the handset on the base or use the other phone line without disconnecting the current call.±

To release a line from hold and continue your conversation, press that line’s button on the handset or base. You can also release a call from hold by lifting the handset if the handset is on the base, or picking up an extension phone.

You can alternate between the two lines by pressing HOLD, then the button for the desired line.

59+6%*+0)"$'69''0"6*'" *#0&5'6"#0&" 52'#-'42*10'

To switch to the speakerphone while you are using the handset, press on the handset, then press the in-use line's button (LINE 1 or LINE 2) on the base.

To switch to the handset while you are using the speakerphone, just lift the handset off the base. Or, if the handset is off the base, press HOLD on the base, then press the in-use line's button (LINE 1 or LINE 2) on the handset.

75+0)"$16*"6*'"*#0&5'6" #0&"52'#-'42*10'

To use the handset to join a call at the base, or to use the base to join a conversation at the handset, press the line button for the line that is in use. You hear a busy tone.

Before the tone ends, press the line button again.

During the call, one party can hang up and the call can continue. To end the call, you must hang up both the base and handset.±

To talk with two parties using both lines, see “4-WayConferencing” on Page 16.

14

75+0)"#"*'#&5'6

You can make or answer calls with handsfree convenience using an optional headset (available at RadioShack) that has a 3/32-inchplug.

To connect the headset, pull open the rubber cover on the side of the handset, then insert the 3/32-inchplug into the jack.±

With a headset connected, you make or answer calls as usual using the keys on the handset.

You can use a handset holder (available at RadioShack) to hang the handset on your belt for greater convenience.

When you finish using the headset, disconnect it from the handset and close the rubber cover to protect the jack.

/#-+0)"#"%10('4'0%'"%#..

5/9#;"%10('4'0%+0)

Follow these steps to use both phone lines to set up a 3- way call. The procedure is the same for the handset and the base.

1.Place the first call on hold.

2.Make or answer a call on the other line.

3.Once you have the second party on the line, press CONF (CONF/9 on the handset) to bring in the first party. If you are using the handset, both line indicators on the base flash green. If you are using the

speakerphone, the indicators stay lit green. The handset displays 9ed\[h[dY[ aboveB_d[ý',B_d[ý( if you are using the handset.9ed\ý8Wi[ andB_d[ý',B_d[ý( appear if you are using the speakerphone.

4.To end the conference call, press one line button, then the other.

To hang up one line and continue talking on the other, press the line button you want to hang up.

±"016'"±"

Connecting a headset disconnects the handset’s earpiece and microphone, but it does not affect the speakerphone.

SELECT/VOLUME on the handset also controls the connected headset's volume.

If you place the handset on the base face down to recharge it while the headset is connected, be sure the handset seats properly.

Using a Headset

15

Phones Extension

±"016'"±"

Extension Phones

If you hang up the phone and someone is still on that line on an extension, the phone's line indicator(s) might not stay lit.

Using Redial

Each keypad has a separate redial memory. You cannot redial a number you dialed on one keypad using the redial key on the other.

The redial memory is common to both lines. You can redial the number you originally dialed on Line 1 using Line 2, as long as you use the same keypad as previous.

The redial memory holds up to 32 digits, so you can redial long distance as well as local numbers.

To talk on one line without disconnecting the other, press HOLD or CALL ID/HOLD, then the button for the line you want to talk on. To return to a 3-way conversation, press CONF or CONF/9.

6/9#;"%10('4'0%+0)

Follow these steps to use both lines and the phone's intercom function to set up a four-waycall (see “Using the Paging/Intercom Features” on Page 17).

1.Make a 3-wayconference call.

2.Press 8/INTCM on the handset orINTERCOM on the base to page the other keypad. The two outside lines are automatically put on hold, but the parties on both lines can talk to each other.

To answer the page, press8/INTCM on the handset, orINTERCOM on the base, then pressCONF/9 on the handset orCONF on the base.

To end the conference call, press LINE 1 and LINE 2 on one keypad, then press LINE 2 on the other keypad.

To hang up one line and continue talking on the other, press the line button that you want to hang up.

You can also make a conference call using both the phone and an extension phone. (See “Extension Phones”.)

':6'05+10"2*10'5

The phone detects when an extension phone is in use. The corresponding line indicator flashes on the base and ?dýKi[ flashes on the handset’s display along withB_d[ý' orB_d[ý(.

To join the conversation from the handset or base, press the line button for the in-useline. While the busy tone is sounding, press the line button again.±

75+0)"4'&+#.

You can quickly dial the last number dialed on either line. When you hear a dial tone, simply press REDIAL/PAUSE on the base or the handset.±

16

75+0)"(.#5*

FLASH (DEL/FLASH on the handset) performs the electronic equivalent of a switchhook operation for special services, such as Call Waiting.

For example, if you have Call Waiting, press FLASH to answer an incoming call without disconnecting the current call. PressFLASH again to return to the first call.±

610'"5'48+%'5"10"#"27.5'"

.+0'

Some special services, such as bank-by-phone,require tone signals. If you have pulse service, you can still use these special tone services by following these steps.

Dial the service’s main number. When the service answers, press TONE/*. Any additional numbers you dial are sent as tone signals. When you hang up, the phone automatically resets to pulse dialing.

75+0)"6*'"2#)+0)1 +06'4%1/"('#674'5

You can use the phone as a two-waypager and intercom between the base and the handset. This is useful if the handset is away from the base and you want to locate it, or if you want to have a conversation between the handset and the base.

To page the handset from the base, press INTERCOM. The

handset rings, and FW]_d] appears on the handset’s display. Press8/INTCM on the handset to answer the page.?dj[hYec

appears.

To page the base from the handset, press 8/INTCM.

FW]_d]ý8Wi[ appears, and the base rings. PressINTERCOM on the base to answer the page.?dj[hYec appears on the

handset's display.±

To end an intercom call, press 8/INTCM or INTERCOM.

During a call, you can page someone at either the base or the handset to join the conversation.

1.Press INTERCOM or8/INTCM. The current call is placed on hold.#

±"016'"±"

Using Flash

If you do not have any special services, pressing FLASH might disconnect the current call.

Using the Paging/Intercom

Features

The paging ends in one minute if nobody answers. Press

INTERCOM or 8/INTCMagain.

You cannot page the base or handset if it is already in use. You hear a warning tone.

If a call comes in during an intercom conversation, either of the intercom parties can answer the call as they normally would by pressing the ringing line’s button. The intercom call automatically disconnects.

Using Flash

17

Dialing Memory

±"016'"±"

An error tone sounds and the phone exits the storing process if you wait more than 30 seconds between key presses.

If the phone sounds five quick beeps, you have made an entry error and the number was not stored. Re-enterthe location number.

Each tone or pause entry uses one digit of memory.

2.Press INTERCOM or8/INTCM again to transfer the call when the person at the base or handset answers.

To start a 3-waycall, tell the person at the base or handset to press the line button for the call, then press the same button twice on your keypad when they answer the page.

/'/14;"&+#.+0)

You can store up to 30 numbers in the handset’s memory and another 10 in the base’s memory, then dial a stored number by pressing a memory location number. You can also store a name with each number in the handset's memory. Each stored number can be up to 20 digits long, and each name can be up to 13 characters.

You cannot dial a number stored in one memory location (the base or the handset) using the keypad on the other.

5614+0)"#"07/$'4"+0"/'/14;

+P"VJG"*CPFUGV

1.Lift the handset.

2.Hold down MEM untilC[cehoýIjeh[ and a list of memory location numbers (and names, if any) appears.

3.Select an empty memory location (or one you want to replace) by entering the location number (01–30)or using8/INTCM orCONF/9 to scroll through the list.

Precede a single-digitnumber with a 0 (for example, 01, 02, 03, etc.).±

4.Press SELECT/VOLUME.Ijeh[ýDWc[ appears. If you do not want to enter a name, skip to Step 6.

5.To enter a name, use the number keys. Refer to the letters on the number keys to select the desired letter. Press the key once for the first letter in upper case, press twice for the second letter in upper case, and so on. To enter the lower case letter, press four times (or five times) to display the first letter in lower case, five or six times for the second letter, and so on.

For example, to enter John: press 5 once; upper case@ appears. Then press6 six times; lower casee appears. Press4 five times; lower case^ appears. Finally, press6 five times; lower cased appears.

18

To enter two letters from the same key in a row, press #/

7 to move the cursor to the next position. For example to enter AB, press 2;7 appears. Then press#/7, the cursor moves to the next position, then press2 twice so8 appears.

To enter a space, press#/7 twice without entering any character.

To enter a number, repeatedly press the corresponding number key until the number appears.

To enter a special character, use 0. Each time you press 0, the characters appear in this order:

ç ¶ý& âýá (space) &

If you make a mistake, use 6/* or#/7 to move the cursor over the error, then enter the correct character, or pressDEL/FLASH to delete a character. To delete all characters, hold downDEL/FLASH for at least 1 second.

6.Press SELECT/VOLUME.Ijeh[ýDkcX[h appears.

7.Enter the number and any tone and pause entries (see “Tone Services On a Pulse Line” on Page 17 and “Entering a Pause” on Page 20).

8.Press SELECT/VOLUME. The phone beeps andC[cehoý ddýIjeh[Z appears. After 2 seconds,ýC[cehoýIjeh[ appears, and you can repeat Steps 3 – 8 to store more numbers.

To replace a stored number, simply store a new one in its place.

'FKVKPI"QT"&GNGVKPI"C"0WODGT"KP"VJG" *CPFUGV)U"/GOQT[

1.Lift the handset.

2.Hold down MEM untilC[cehoýIjeh[ and a list of memory location numbers (and names, if any) appears.

3.Choose a memory location you want to edit or delete by pressing 8/INTCM orCONF/9, or entering its location number.

4.Press SELECT/VOLUME. Three options (;Z_jýC[cehoýdd,

:[b[j[ýC[cehoýdd, and =eý8WYa) appear. Press

8/INTCM orCONF/9 to choose an option, follow the instructions listed, then pressSELECT/VOLUME.

Memory Dialing

19

Dialing Memory

;Z_jýC[cehoýdd — Edit the record as described in Steps5–8of “In the Handset” on Page 18.

:[b[j[ýC[cehoýdd — The display prompts you to confirm

the deletion. Move the cursor to O[i orDe, then pressSELECT/VOLUME. The phone beeps, andC[cehoýddý :[b[j[Z appears.

=eý8WYa — Returns you to the list of memory numbers.

When you finish editing or deleting memory numbers, press MEM or return the handset to the base to exit the Memory Store display.

+P"VJG"$CUG

1.Press MEM. The CHARGE indicator blinks.

2.Enter the number (up to 20 digits) and any tone mode changes or pause entries (see “Tone Services On a Pulse Line” on Page 17 or “Entering a Pause”).

3.Press MEM again, then enter the memory location number (0 – 9) where you want to store the number. A tone sounds to indicate that the number is stored.

To clear a stored number, simply store a new number in its place. Or, press MEM twice. Then press the memory location number (0 – 9) you want to clear. A tone sounds.

Use the supplied memory directory sticker to record your stored numbers.

Peel the backing from the sticker and attach it to the base.

'06'4+0)"#" 2#75'

In some telephone systems, you must dial an access code (9, for example) and wait for a second dial tone before you can dial an outside number. You can store the access code with the phone number. However, you should also store a pause after the access code to allow the outside line time to connect.

To enter a 2-secondpause, pressREDIAL/PAUSE. The handset display showsF for pause entry. For a longer pause, repeatedly pressREDIAL/PAUSE.

20