Radio Shack 43-3824 User Manual

Size:
647.27 Kb
Download

2.4GHz Cordless Phone

with Caller ID and Digital Answering System

43-3824

20 Number Memory Dialing — stores 20 numbers in memory for easy dialing. See “Memory Dialing from Talk Mode” on Page 20.

Long Battery Life — the supplied battery pack (when fully charged) provides about 7 hours of talk time or 14 days of standby time.

20 Channels — automatically selects a clear channel when you make or answer a call. You can also manually change channels during a call. See “Selecting a Different Channel” on Page 16.

Headset Jack — connects an optional headset (available at your local RadioShack store) forhands-freeconvenience. See “Headset Installation” on Page 42.

Toll-Saver — lets you avoid unnecessary charges when you call by long distance to check your messages. See “Setting the ring time” on Page 31.

! IMPORTANT!

If an icon appears at the end of a paragraph, go to the box on that page with the corresponding icon for pertinent information.

o— Warning! — Important

 

— Caution

 

Ô— Note

 

 

 

 

OWNER’S MANUAL

 

 

Please read before using this equipment.

 

 

© 2003 RadioShack Corporation.

 

 

All Rights Reserved.

 

 

RadioShack and RadioShack.com are trademarks used by

 

 

RadioShack Corporation.

 

 

ENERGYSTAR and the ENERGYSTAR certification mark

 

 

are registered US marks.

Instructions Safety Important

CONTENTS

 

Important Safety Instructions

2

Battery SafetyInstructions ....

4

Introduction ..........................

5

Important Caller ID

 

Information ...........................

5

Read This Before

 

Installation ........................

6

Installation ............................

7

Mounting the Phone .........

7

On a Desk Top.................

7

On a Wall Plate or Wall ...

8

Connecting, Charging and

 

Replacing the Battery

 

Pack ..................................

9

Recycling Ni-Cd

 

Batteries.........................

10

Setting Menu Options .....

11

Caller ID Options............

11

Choosing the Dial Mode. 12

Setting the Language.....

13

Operation ...........................

14

Making and Receiving

 

Calls ................................

14

Adjusting the Handset Ringer

and Earpiece Volume ......

15

Handset Ringer Tone and

Volume ..........................

15

Earpiece Volume ...........

15

Temporarily Mute

 

Ringer ...........................

15

Redial .............................

15

Tone Dialing Switch-over

15

Traveling Out-of-Range ...

15

Selecting a Different

 

Channel ..........................

16

Page ...............................

16

Flash and Call Waiting ....

16

Storing Phone Numbers and

Names ............................

16

Steps for Entering Names

 

and Special Characters ..

18

If You Make a Mistake while

Entering a Name ...........

18

Making Calls with Memory

 

Dialing .............................

19

Memory Dialing from

 

Standby Mode ...............

19

Memory Dialing from Talk

Mode .............................

20

Chain Dialing ..................

20

Editing a Stored Name and/or

Phone Number ...............

20

Erasing a Stored Name and

Phone Number ...............

22

Testing Stored Emergency

Numbers .......................

22

One-touchSpeed Dial ....

22

Making calls with the

 

Speed Dial ......................

23

(continued)

 

WARNING: To reduce the risk of fire or shock hazard, do not expose this product to rain or moisture.

 

 

.CAUTION.

 

 

 

CAUTION: TO REDUCE THE RISK OF ELECTRIC

 

 

 

!

 

SHOCK, DO NOT REMOVE COVER OR BACK. NO

 

 

 

 

 

USER-SERVICEABLEPARTS INSIDE. REFER

 

RISK OF ELECTRIC SHOCK

 

 

 

SERVICING TO QUALIFIED PERSONNEL.

 

 

DO NOT OPEN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The lightning symbol is intended to alert you to

 

 

 

 

 

 

 

 

The exclamation symbol is intended to

 

the presence of uninsulated dangerous voltage

!

 

inform you that important operating and

 

within this product’s enclosure that might be of

 

maintenance instructions are included in

 

sufficient magnitude to constitute a risk of

 

 

the literature accompanying this product.

 

electric shock. Do not open the product’s case.

 

 

 

 

 

 

 

 

IMPORTANT SAFETY INSTRUCTIONS

When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:

1.Read and understand all instructions.

2.Follow all warnings and instructions marked on the product.

3.Never install telephone wiring during a lightning storm.

4.Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.

5.Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.

6.Use caution when installing or modifying telephone lines.

7.Do not affix the AC power supply cord to building surfaces with metal fittings (if the product has an AC power cord).

8.Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

9.Do not use this product near water, for example, near a bathtub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool.

10.Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious damage to the product.

2

11.Slots and openings in the telephone’s cabinet and the back or bottom are provided for ventilation. To protect the telephone from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register. This product should not be placed in a built-ininstallation unless proper ventilation is provided.

12.This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your local power company.

13.Do not allow anything to rest on the power cord. Do not locate this product where the cord will be stepped on.

14.Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.

15.Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on the product.

16.To reduce the risk of electric shock, do not disassemble this product. Take it to a qualified serviceman when service or repair work is required. Opening or removing covers may expose you to dangerous voltages or other risks. Incorrect reassembly can cause electric shock when the product is subsequently used.

17.Unplug this product from the wall outlet and refer servicing to qualified services personnel under the following conditions:

When the power cord plug is damaged or frayed.

If liquid has been spilled into the product.

CONTENTS

 

(continued)

 

Deleting the Speed Dial ..

23

Caller ID .............................

24

When the Telephone

 

Rings ..............................

24

Viewing the Caller ID

 

Message List ..................

25

Deleting Information from the

Caller ID List ...................

25

Deleting a Caller ID

 

Message ........................

25

Deleting all Caller ID

 

Names/Numbers ...........

26

Using the Caller ID List ... 26

Calling a Party from the

 

Caller ID List .................

26

Long Distance Calls and

 

Area Code Setting/

 

Cancellation ..................

27

Storing Caller ID Messages

in Memory dialing ..........

27

The Integrated Answering

 

Device ................................

28

Features ...........................

28

Turning the Answering

 

System On/Off ................

28

Setting up Your Answering

 

System ............................

29

Using the Menu Mode ...

29

Setting the Time ............

30

Setting a Personal Security

Code (PIN) ....................

31

Setting the ring time ......

31

Selecting the message

 

record time ....................

32

Setting the Message Alert

tone ...............................

33

Setting Your Outgoing

 

Message (Greeting) ........

34

Using Your Answering

 

System ............................

36

Additional Information ........

42

Installing the Optional

 

Beltclip ............................

42

Headset Installation ........

42

Troubleshooting ..................

43

Care ...................................

45

Important Information .........

45

FCC Statement ..................

45

Surge Protection .............

46

Important Safety Instructions

3

Instructions Safety Battery

CAUTION

TO REDUCE THE RISK OF FIRE OR INJURY, READ AND FOLLOW THESE INSTRUCTIONS.

As an ENERGYSTAR Partner, RadioShack Corporation has determined that this product meets the ENERGYSTAR guidelines for energy efficiency.

If the product has been exposed to rain or water.

If the product does not operate normally by following the operating instructions.

18.Adjust only those controls that are covered by the operating instructions because improper adjustments of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation.

19.If the product has been dropped or the cabinet has been damaged.

20.If the product exhibits a distinct change in performance.

21.Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.

22.Do not use the telephone to report a gas leak while in the vicinity of the leak.

BATTERY SAFETY

INSTRUCTIONS

Use only the appropriate type and size battery

pack specified in the instruction manual provided for this product.

Do not dispose of the battery pack in a fire. The cell may explode. Check with local codes for possible special disposal instructions.

Do not open or mutilate the battery pack. Released electrolyte is corrosive and may cause damage to the eyes or skin. It may be toxic if swallowed.

Exercise care in handing the battery pack in order not to short it with conducting materials such as rings, bracelets and keys. The battery or conductor may overheat and cause burns.

4

Charge the battery pack provided with or identified for use with this product only in accordance with the instructions and limitations specified in the instruction manual provided for this product.

Observe proper polarity orientation between the battery pack and battery charger.

SAVE THESE

INSTRUCTIONS

INTRODUCTION

Thank you for purchasing a RadioShack 900 MHz Cordless Telephone. Your telephone provides excellent clarity and range and integrates Caller ID, Call Waiting ID, and a digital answering system into one space-savingdevice. The 900 MHz band provides less interference, clearer sound, and greater range than 46/49 MHz cordless telephones.

The digital answering system provides clear reliable messaging with call screening, day/time stamp, call counter, remote access and instant skip or replay messaging.

The Caller ID records each caller’s name (if available in your area), telephone number, and the date and time of the call, as provided by your local phone company to Caller ID service subscribers. !

IMPORTANT CALLER ID INFORMATION

To use Caller ID and Call Waiting, you must be in an area where those services are available and you must subscribe to those services through your local phone company. Where Caller ID is offered, one or more options are generally available:

! IMPORTANT!

Cordless phones such as this one require AC power to operate. When the AC power is off, you cannot dial out or receive incoming calls using your phone. To be safe, you should also have a phone that does not need AC power to operate (not a cordless phone) so you can still make and receive calls if there is an AC power failure.

When AC power is lost, the phone loses the security access-protectioncode connection between the base and the handset. When power is restored, put the handset on the base briefly to restore this connection.

Introduction

5

Information ID Caller Important

caller’s number only

caller’s name only

caller’s name and number

If you subscribe to Call Waiting ID and Caller ID, the system can show you the incoming caller information, even when you are already talking on the phone.

READTHISBEFOREINSTALLATION

We have designed your phone to conform to federal regulations and you can connect it to most phone lines. However, each device that you connect to the telephone line draws power from the line. We refer to this power draw as the phone’s ringer equivalence number, or REN. The REN is on the bottom of your phone.

If you use more than one phone or other device on the line, add up all the RENs. If the total is more than five (three in rural areas), your phones might not ring. If ringer operation is impaired, remove one of the devices from the line.

The digital answering system stores up to 11 minutes of messages on a computer chip and records each message’s day and time. This gives you advanced capabilities over tape-basedanswering machines:

You can delete individual messages and save the rest.

There are no tapes to bother with and no tape mechanisms to wear out.

The remote operation feature lets you operate your answering system from a touch-tonephone (or from a rotary phone with a pocket tone dialer).

6

INSTALLATION

MOUNTING THEPHONE

You can place the phone on a desk or table, mount it on a standard wall plate, or directly on a wall. Choose a location that is: Ô

near an AC outlet

near a modular telephone line jack

out of the way of normal activities

away from electrical machinery, electrical appliances, metal walls or filing cabinets, wireless intercoms, alarms, and room monitors

away from other cordless phones

You can try different locations to see which provides the best performance.

Your telephone connects directly to a modular telephone line jack. If your telephone wiring does not have a modular jack, you can update the wiring yourself using jacks and adapters (available at your local RadioShack store or online at RadioShack.com), or have the telephone company update the wiring for you. You must use compatible modular jacks that are compliant with Part 68 of FCC Rules. The USOC number of the jack to be installed is RJ11C (RJ11W for a wall plate).

On a Desk Top

DC IN 9V

TEL LINE

1. Plug one end of the

 

 

supplied long modular

 

 

cord into the TEL

 

 

LINE jack on the

 

 

base’s back.

 

 

2. Plug the modular cord’s other end into a modular telephone line jack.

CAUTION

You must use a

!Class 2 power source that

supplies 9V DC and delivers at least 350 mA. Its center tip must be set to positive and its plug must fit the phone's DC IN 9V jack. The supplied adapter meets these specifications. Using an adapter that does not meet these specifications could damage the phone or the adapter.

Always connect the AC adapter to the phone before you connect it to AC power. When you finish, disconnect the adapter from AC power before you disconnect it from the phone.

ÔNOTE Ô

If your home has specially wired alarm equipment connected to the telephone line, be sure that installing the system does not disable your alarm equipment.

If you have questions about what will disable alarm equipment, contact your telephone company or a qualified installer.

Installation

7

Installation

3.Insert the supplied AC adapter’s barrel plug into the DC IN 9V jack on the back.

4.Route the adapter’s cord through the strain relief slot on the base’s bottom.

5.Plug the adapter into a standard AC outlet.

6.Lift the base’s antenna to a vertical position.

On a Wall Plate or Wall

To mount the phone directly on a wall, you need two screws (not supplied) with heads that fit into the keyhole slots on the base. Drill two holes 315/16 inches apart. Thread a screw into each hole, letting the heads extend about1/8 inch.

1. Insert the two tabs at the top of the narrow end of the supplied bracket into the base’s upper tab slots, then press down on the bracket’s latches and insert them into the lower slots.

2.Plug one end of the supplied modular cord (short for a wall plate, long for direct wall mounting) into the TEL LINE jack on the base’s back.

3. Insert the

DC IN 9V

TEL LINE

supplied AC

 

 

adapter’s barrel

 

 

plug into the DC

 

 

IN 9V jack.

 

 

4. Route the adapter and modular cords through the base’s grooves.

8

5.For a wall plate, plug the modular cord’s other end into the wall plate jack, then align the base’s keyhole slots with the wall plate studs and slide the base downward to secure it.

For direct wall mounting, align the base’s keyhole slots with the mounting screws and slide the base downward to secure it.

6.Plug the adapter into a standard AC outlet.

7.Press and lift out the handset

holder, flip it over as shown, then snap it back into place so it holds the handset.

8.Lift the base’s antenna to a vertical position.

CONNECTING, CHARGING ANDREPLACING THEBATTERYPACK

The phone comes with a rechargeable Ni-Cd(nickel-cadmium)battery pack installed in the handset, but not connected. Before using your phone, you must connect the battery pack, then charge it for about 24 hours.

1.Press up on the latch and lift the battery pack compartment cover.

2.Lift the battery pack out of the compartment.

Installation

9

Installation

! IMPORTANT!

3. Plug the battery pack’s

 

connector into the socket in

Be sure the battery pack is

 

 

the compartment. The

properly connected before

 

connector fits only one way.

you try to charge it. The

 

 

 

CHARGE indicator lights

4.

Put the battery pack in the

when the handset is on the

 

compartment.

base even if the battery

 

 

 

pack is not connected

5.

Replace the cover.

properly.

 

 

Ô NOTEÔ

To charge the battery pack, place the handset on

the base, face up or down. The base’s CHARGE/IN

• If the phone does not

USE indicator lights. !

work, recharge the

Recharge the battery pack when Low Battery

battery pack. (The

flashes.Ô

battery power might be

 

 

too low for the display to

When you first use the phone after charging or

operate.)

• If the battery pack

recharging the battery pack, the phone might not

becomes weak during a

work and you might hear error beeps. If this

call, the handset beeps

happens, return the handset to the base for about 5

and Low Battery

seconds to change the security access-protection

flashes. When this

code.

happens, you cannot

make a call on the

Using a pencil eraser, clean the charging contacts

phone until you recharge

the battery pack.

on the handset and the base about once a month.

If the battery pack is

completely discharged About once a month, fully discharge the battery

 

or the base loses power

pack by keeping the handset off the base until Low

 

while the handset is

Battery flashes. Otherwise, the battery pack

 

away from it, place the

 

loses its ability to fully recharge.

 

handset on the base to

 

change the security

The supplied battery pack should last about a year.

 

access-protectioncode.

 

If it was the handset that

If the battery pack does not hold a charge for more

 

lost power, recharge the

than 2 hours after an overnight charge, replace it

 

battery pack.

with a new 3.6V, 600 mAh battery pack with a

 

 

 

 

connector that fits the socket in the battery

 

oWARNINGo

 

compartment. You can order a replacement battery

 

Dispose of the old battery

pack through your local RadioShack store (or online

 

pack promptly and properly.

at RadioShack.com). Install the new battery pack

 

Do not burn or bury it (see

and charge it for about 24 hours. o

 

“Battery Safety Instructions”

 

 

 

on Page 4 for additional

If you have trouble replacing the battery pack, take

 

information on proper

the phone to your local RadioShack for assistance.

 

battery handling).

 

 

 

 

 

 

 

10

Recycling Ni-CdBatteries.

The EPA certified RBRC® Battery Recycling Seal on thenickel-cadmium(Ni-Cd)battery indicates RadioShack is voluntarily participating in an industry program to collect and recycle these

batteries at the end of their useful life, when taken out of service in the United States or Canada. The RBRC program provides a convenient alternative to placing used Ni-Cdbatteries into the trash or the municipal waste stream, which may be illegal in your area. Please call1-800-THE-SHACK(1-800-843-7422)for information onNi-Cdbattery recycling and disposal bans/restrictions in your area. RadioShack’s involvement in this program is part of the company’s commitment to preserving our environment and conserving our natural resources.

SETTINGMENUOPTIONS

There are five setup options available. They are Caller ID options [AutoTalk, CIDCW (Caller ID on Call Waiting), and Area Code], Dial Mode and Language.

AutoTalk allows you to answer the phone without pressing the talk/FLASH button. If the phone rings when AutoTalk is on, simply remove the handset from the base and the phone automatically answers the call. If the phone rings when AutoTalk is off, you must presstalk/FLASH to answer the call.

Caller ID Options

To change your Auto Talk and CIDCW:

1.Press and hold CID/MENU.

2.Use VOL/ orVOL/ to move the pointer to the selection that you would like to change.

Press SEL to toggle betweenOn andOff.

Installation

11

Installation

Ô NOTEÔ

Caller ID Options

If your calling area requires 10-digitdialing, do not program this option.

When the area code has already been stored in memory, the stored area code will be displayed. To change it, use the

DELETE/CHANNNEL and number keys to enter the new area code. Then press SELECT. A confirmation tone sounds.

To complete the setting, press end or return the handset to the base unit.

Choosing the Dial Mode

If you are not sure of your dialing system, make a trial call. If the call connects, leave the setting as is, otherwise set for pulse dialing.

If your phone system requires pulse dialing and you need to send the DTMF tones for certain situations during a call, you may “switchover” to tone dialing (refer to “Tone Dialing Switch-over”on page 15).

3.Press end and return the handset to the base unit to complete the setting. The handset returns to the standby mode.

To enter your Area Code Ô

If you enter a 3-digitarea code number in theArea Code option, your local area code does not appear in Caller ID messages. Do not program this option, if your calling area requires10-digitdialing.

When reviewing Caller ID messages, you will see only the local seven digit number. For calls received from outside your local area code, you will see a full 10-digitnumber.

1.When the phone is in the standby mode, press and hold CID/MENU.

2.Press VOL/ twice to selectArea Code. Ô

3.Press SELECT.

4.Use the number keys (0 to9) orDELETE/ CHANNNEL to enter the3-digitarea code.

5.Press SELECT. A confirmation tone sounds and the displayed area code is entered.

6.Press end or return the handset to the base unit to complete the setting. The handset returns to the standby mode.

Choosing the Dial Mode Ô

Most phone systems use tone dialing which sends DTMF tones through the phone lines. However, some phone systems still use pulse dialing such as in rural areas. The default setting is tone dialing. Depending on your dialing system, set the mode as follows:

1.When the phone is in the standby mode, press and hold CID/MENU.

12

2.Press VOL/ three times to selectDial.

3.Press SEL to toggle betweenTone and

Pulse.

4.Press end or return the handset to the base unit to complete the setting. The handset returns to the standby mode.

Setting the Language

1.When the phone is in the standby mode, Press and hold CID/MENU.

2.Press VOL/ four times to selectLanguage.

3.Press SEL to toggle betweenEng andEsp.

4.Press end or return the handset to the base unit to complete the setting. The handset returns to the standby mode.

Installation

13

Ô NOTEÔ

Refer to page 11 “Setting menu options” to turn on the Auto Talk feature if desired.

Operation

OPERATION

MAKING ANDRECEIVINGCALLS

Even when you turn off the base’s ringer, you can still make or receive calls using this phone. Telephones on the same line and the handset (if its ringer is not turned off) still ring when there is an incoming call.

Action

Handset On Base

Handset Off Base

 

 

 

 

Pick up the handset

Press talk/FLASH,

To

(Auto Talk: On),Ô or

any number, /TONE/

receive

pick up the handset

or #/ (Auto Talk:

a call

and press talk/FLASH

On).

 

(Auto Talk: Off).

 

 

 

 

 

1)Pick up the handset.

1)Press talk/FLASH.

 

2)Press talk/FLASH.

2)Listen for the dial

 

3)Listen for the dial

tone.

To

tone.

3)Dial the number.

4)Dial the number.

 

make a

 

OR

OR

call

1)Pick up the handset.

Dial the number, then

 

 

2)Dial the number,

press talk/FLASH.

 

then press talk/

 

 

FLASH.

 

To hang

Press end or return the handset to the base

up

(Auto Standby).

 

 

 

 

 

1)Pick up the handset.

1)Press talk/FLASH.

 

2)Press talk/FLASH.

2)Listen for the dial

 

3)Listen for the dial

tone.

 

tone.

3)Press REDIAL/

To

4)Press REDIAL/

PAUSE.

PAUSE.

 

redial

 

OR

OR

 

 

1)Pick up the handset.

Press REDIAL/

 

2)Press REDIAL/

PAUSE., then press

 

PAUSE, then press

talk/FLASH.

 

talk/FLASH.

 

 

 

 

14

ADJUSTING THEHANDSETRINGER

AND EARPIECEVOLUME

Handset Ringer Tone and Volume

Press VOL/ orVOL/ in standby mode to select one of five ringer tones and volume combinations.

Earpiece Volume

Pressing VOL/ orVOL/ during a call will change the earpiece volume of the handset. This setting will remain in effect after the telephone call has ended.Ô

Temporarily Mute Ringer

If the handset is off the base, simply press end to temporarily mute the incoming ring. The ringer will sound with the next incoming call.

REDIAL

The REDIAL/PAUSE key redials the last number dialed. The redialed number can be up to 32 digits long.

TONEDIALINGSWITCH-OVER

Some telephone companies use equipment that requires pulse dialing (sometimes referred to as rotary dialing). If you need to enter tone dialing digits, you can switch-overto tone dialing during the call. For example, entering your bank account number after you have called your bank. Ô

Initially make your call with the pulse dialing mode.Ô Once your call connects, press /TONE/ . Enter the desired number. These digits will be sent as tone dialing. Once the call ends, the tone mode is canceled and pulse dialing mode resumes.

TRAVELINGOUT-OF-RANGE

During a call, as you begin to move your handset too far from your base unit, noise increases. If you

Ô NOTEÔ

Earpiece Volume

When you press VOL/ in Maximum mode orVOL/ in Low mode, an error tone sounds.

Tone Dialing Switch-over

The tone feature only applies when the dial mode is set to pulse.

This special number can be stored in a memory location. This is referred to as Chain Dialing (See page 20.)

Operation

15

Operation

Ô NOTEÔ

Page

Paging is also canceled when the phone receive an incoming call.

Flash and Call Waiting

You must subscribe through your local telephone company to receive Call Waiting Service.

Storing Phone Numbers and Names

In memory dialing operation, you must press a key within 30 seconds. Otherwise, an error tone will sound and the phone will return to standby.

If you return the handset to the base, the phone will return to standby also.

pass the range limits of the base unit, your call will terminate within 1 minutes.

SELECTING ADIFFERENTCHANNEL

If you encounter interference while using your phone, you can manually change the phone’s channel for clear operation. This function works only when the phone is in use.

Press DELETE/CHANNEL.Scanning appears on the display, indicating the phone is changing to another channel.

PAGE

To locate the handset (while it’s off the base), press find hs on the base. The handset beeps for 60 seconds.Ô

Paging is canceled when pressing any handset key, find hs on the base or the handset is returned to the base.

FLASH ANDCALLWAITING

If you have “Call Waiting” service and a call waiting tone sounds while you are on a call, press talk/ FLASH to accept the waiting call. There is a short pause, then you will hear the new caller. To return to the original caller, presstalk/FLASH again.Ô

STORINGPHONENUMBERS ANDNAMES

Memory Dialing allows you to dial a number using just a few key presses. Your phone stores up to 10 names/numbers in the handset. Ô

1.Press MEM. Select Memory is displayed.

2.Press VOL/ orVOL/ , or enter a number (01 - 20) to select the memory location where you would like to store the number.

3.Press MEM orSELECT.

16

4.Press MEM orSELECT. A cursor flashes indicating that the display is ready for the name to be entered.

If Edit MemoryXX appears, the selected memory location is already stored. Then you must either edit the entry in this location, delete the entry in this location, or selectGo Back to choose another location.

5.To enter a name (up to 13 characters), use number keys.

See “Steps for Entering Names and Special Characters” on Page 18. (See pages 17-18)

Use #/ and/TONE/ to move the cursor to the desired location.

Use DELETE/CHANNEL to delete characters as needed.

Press and hold DELETE/CHANNEL to delete all the characters.

If a name is not required, go to step 6.

6.Press MEM orSELECT.Store Number is displayed.

The cursor flashes indicating that the display is ready for the number to be entered.

7.Use the number keys to enter the phone number.

The phone number cannot exceed 20 digits.Ô

Use REDIAL/PAUSE to enter a pause in the dialing sequence. The display shows aP. Each pause counts as one digit and represents a two second delay of time between the digits as they are sent.

Operation

ÔNOTE Ô

The pause feature is useful for long distance calling, credit card dialing, or sequences that require a pause between digits.

17

Use DELETE/CHANNEL to delete digits as needed.

8.Press MEM orSELECT. You will hear a confirmation tone.Ô Memory storage is complete. For example, if you store a name and number into memory location number 01, the display showsMemory01 Stored.

After about 2 seconds, the Select Memory Screen is displayed.

Repeat steps 2 - 8 to store more numbers.

9.Press end to return to standby mode.

STEPS FORENTERINGNAMES ANDSPECIALCHARACTERS

Refer to the letters on the number keys to select the desired characters.

With each press of a numeric key, the displayed character appears in the following order:

Upper case letters first, lower case letters next, and finally the number corresponding to the key.

Operation

If You Make a Mistake while Entering a Name

Use /TONE/ or#/ to move the cursor to the incorrect character, pressDELETE/CHANNEL to erase up to the wrong entry, then enter the correct

18

character. To delete all characters, press and hold

DELETE/CHANNEL.

For example, to enter John; Ô

1.Pick up the handset. Press MEM.

2.Enter a number or press VOL/ orVOL/ to select a memory location number.

3.Press MEM orSELECT.

4.Press MEM orSELECT. (When there is information already stored in the selected memory location,Edit MemoryXX is displayed. See “Editing a Stored Name and/or Phone Number” on Page 20.)

5.Press 5 once.

6.Press 6 six times.

7.Press 4 five times.

8.Press 6 five times.

9.When finished, press MEM orSELECT.

To continue to store the telephone number, proceed to step 7 on page 17.

MAKINGCALLS WITHMEMORY

DIALING

Memory Dialing from Standby Mode

1.Press MEM. The handset displays your programmed memory locations.

2.Press VOL/ orVOL/ , or enter a number (01 - 20) to select the memory location you would like to dial. Ô

3.Press talk/FLASH.Talk and the volume setting appear on the display. Then the displayed number is dialed.

Ô NOTEÔ

If the next character uses the same number key, you must press #/ to move the cursor over. Otherwise the next time you press the number key, it changes the character that was previously set.

Operation

19

ÔNOTE Ô

If you press SELECT beforetalk/FLASH, you can confirm the name and the number stored in the selected memory location.

To exit the memory function without dialing, press end. The handset returns to standby.

Whenever you are using a memory menu screen, you must press a key within 30 seconds or the phone will return to standby.

Operation

Memory Dialing from Talk Mode

1.Press talk/FLASH.Talk and the volume setting appears.

2.Press MEM.

3.Press VOL/ orVOL/ , or Enter a number (01 - 20) to select the memory location of the desired phone number. If you pressSELECT, the number is dialed. Ô

4.To hang up, press end.

CHAINDIALING

The memory locations on the handset are not limited to phone numbers. You can also store a group of numbers (up to 20 digits) that you need to enter once your call connects. This is referred to as Chain Dialing.

An example of this is a bank account number. Once you have called your bank, and are prompted to enter the account number, press MEM and select the location number where the special number has been stored. Then presstalk/FLASH.

Store your special number with an identifying name. (See “Storing Phone Numbers and Names” on Page 16.)

EDITING ASTOREDNAME AND/OR

PHONENUMBER

1.Press MEM. Select Memory is displayed.

2.Press VOL/ orVOL/ , or enter a number (01 - 20) to select the memory location you would like to edit, and pressMEM orSELECT.

3.Press MEM orSELECT.

The screen appears with the memory location number that you have selected in the display.

20