Radio Shack 43-3820 User Manual

Size:
307.61 Kb
Download
± — Note

;22/*\"&WCN"*CPFUGV"%QTFNGUU"2JQPG

YKVJ"%CNNGT"+&"CPF"&KIKVCN"#PUYGTKPI"5[UVGO

43-3820

Two Cordless Handsets — allow greater convenience in placement of handsets.

10 Number Memory Dialing — stores 10 numbers in memory on each handset for easy dialing. See “Memory Dialing” on Page 17.

Long Battery Life — the supplied battery pack (when fully charged) provides about seven hours of talk time or seven days of standby time.

20 Channels — automatically selects a clear channel when you make or answer a call. You can also manually change channels during a call. See “Selecting the Channel” on Page 15.

Headset Jack — connects an optional headset (available at your local RadioShack store) forhands-freeconvenience. See “Using a Headset” on Page 17.

Toll-Saver — lets you avoid unnecessary charges when you call by long distance to check your messages. See “Using the TollSaver” on Page 34.

#"+/2146#06"#

If an icon appears at the end of a paragraph, go to the box on that page with the corresponding icon for pertinent information.

— Warning# — Important.— Caution

° — Hint

OWNER’S MANUAL

Please read before using this equipment.

© 2002 RadioShack Corporation.

All Rights Reserved.

RadioShack and RadioShack.com are trademarks used by RadioShack Corporation.

ENERGYSTAR and the ENERGYSTAR certification mark are registered US marks.

Instructions Safety Important

%106'065

Battery Safety Instructions ........

4

Introduction ...............................

5

Important Caller ID

 

Information ................................

5

Read This Before

 

Installation .............................

6

Installation .................................

7

Mounting the Phone ..............

7

On a Desk Top .....................

7

On a Wall Plate or Wall ........

8

Installing the Charging

 

Cradle ....................................

8

Connecting, Charging and

 

Replacing

 

the Battery Pack ....................

9

Recycling

 

Ni-CdBatteries ...................

10

Registering the Second

 

Handset ...............................

10

Setting the Dialing Mode .....

11

Setting the Handset’s Ringer

 

Tone/Volume .......................

12

Turning the Base’s Ringer

 

On/Off ..................................

12

Setting Auto Talk .................

13

Turning Caller ID/Call Waiting

On/Off ..................................

13

Storing Your Area Code ......

13

Telephone Operation ...............

14

Making and Receiving

 

Calls ....................................

14

Selecting the Channel .........

15

Setting the Handset

 

Volume ................................

15

Using Flash .........................

15

Using Redial ........................

16

Muting the Ringer ................

16

Using Tone Services on a

 

Pulse Line ...........................

16

Paging .................................

16

Transferring a Call ...............

17

Using a Headset ..................

17

Memory Dialing ...................

17

Storing a Name and Number

in Memory...........................

17

Editing or Deleting a Number

in Memory...........................

19

Entering a Pause................

20

Reviewing Memory

 

Numbers.............................

20

Dialing a Memory

 

Number...............................

20

Chain-DialingService

 

Numbers ............................

21

Testing Stored Emergency

 

Numbers ............................

21

One-TouchSpeed Dial ........

21

Storing/Editing Numbers ....

21

(Continued)

 

WARNING: To reduce the risk of fire or shock hazard, do not expose this product to rain or moisture.

 

 

.CAUTION.

 

 

 

CAUTION: TO REDUCE THE RISK OF ELECTRIC

 

 

 

!

 

SHOCK, DO NOT REMOVE COVER OR BACK. NO

 

 

 

 

 

USER-SERVICEABLEPARTS INSIDE. REFER

 

RISK OF ELECTRIC SHOCK

 

SERVICING TO QUALIFIED PERSONNEL.

 

 

DO NOT OPEN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The lightning symbol is intended to alert you to

 

 

 

 

 

 

 

 

The exclamation symbol is intended to

 

the presence of uninsulated dangerous voltage

!

 

inform you that important operating and

 

within this product’s enclosure that might be of

 

maintenance instructions are included in

 

sufficient magnitude to constitute a risk of

 

the literature accompanying this product.

 

electric shock. Do not open the product’s case.

 

 

 

 

 

 

 

 

+/2146#06"5#('6;" +05647%6+105

When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:

1.Read and understand all instructions.

2.Follow all warnings and instructions marked on the product.

3.Never install telephone wiring during a lightning storm.

4.Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.

5.Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.

6.Use caution when installing or modifying telephone lines.

7.Do not affix the AC power supply cord to building surfaces with metal fittings (if the product has an AC power cord).

8.Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

9.Do not use this product near water, for example, near a bathtub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool.

10.Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious damage to the product.

2

11.Slots and openings in the telephone’s cabinet and the back or bottom are provided for ventilation. To protect the telephone from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register. This product should not be placed in a built-ininstallation unless proper ventilation is provided.

12.This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your local power company.

13.Do not allow anything to rest on the power cord. Do not locate this product where the cord will be stepped on.

14.Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.

15.Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on the product.

16.To reduce the risk of electric shock, do not disassemble this product. Take it to a qualified serviceman when service or repair work is required. Opening or removing covers may expose you to dangerous voltages or other risks. Incorrect reassembly can cause electric shock when the product is subsequently used.

17.Unplug this product from the wall outlet and refer servicing to qualified services personnel under the following conditions:

When the power cord plug is damaged or frayed.

If liquid has been spilled into the product.

%106'065

(continued)

Using Speed Dial................

22

Deleting a Number in

 

Memory .............................

22

Caller ID Operation .................

22

Reviewing Caller ID

 

Records ...............................

23

Caller ID Messages ............

24

Adding/Deleting the

 

Area Code ...........................

24

Dialing Numbers from a Caller

ID Record ............................

24

Storing a Caller ID Record in

 

Memory ...............................

25

Deleting Caller ID

 

Records ...............................

25

Answering System

 

Operation ................................

26

Using the Menu Button ........

26

Setting the Day/Time ...........

26

Setting the Number

 

of Rings ...............................

27

Setting the Record Time ......

28

Setting the Message

 

Alert Tone ............................

28

Turning the Message Alert

 

Tone Off .............................

29

Selecting the Outgoing

 

Message ..............................

29

Recording/Deleting an

 

Outgoing Message ..............

29

Setting the System to Answer

Calls ....................................

30

Screening Calls ...................

30

Recording Incoming

 

Messages ............................

30

Recording a Memo ..............

31

Recording a

 

Conversation .......................

31

Playing Messages ...............

32

Adjusting the Volume ..........

32

Deleting Messages ..............

33

Remote Operation ...............

33

Setting the Security

 

Code...................................

33

Using the Toll-Saver...........

34

Using Remote

 

Commands............................

34

Remote Commands ...........

36

Troubleshooting ......................

36

Care ........................................

38

FCC Statement .......................

38

The FCC Wants You

 

to Know ...............................

38

Lightning ..............................

39

Important Safety Instructions

3

Instructions Safety Battery

."%#76+10".

TO REDUCE THE RISK OF FIRE OR INJURY, READ AND FOLLOW THESE INSTRUCTIONS.

As an ENERGYSTAR Partner, RadioShack Corporation has determined that this product meets the ENERGYSTAR guidelines for energy efficiency.

If the product has been exposed to rain or water.

If the product does not operate normally by following the operating instructions.

18.Adjust only those controls that are covered by the operating instructions because improper adjustments of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation.

19.If the product has been dropped or the cabinet has been damaged.

20.If the product exhibits a distinct change in performance.

21.Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.

22.Do not use the telephone to report a gas leak while in the vicinity of the leak.

$#66'4;"5#('6;" +05647%6+105

Use only the appropriate type and size battery

pack specified in the instruction manual provided for this product. .#

Do not dispose of the battery pack in a fire. The cell may explode. Check with local codes for possible special disposal instructions.

Do not open or mutilate the battery pack. Released electrolyte is corrosive and may cause damage to the eyes or skin. It may be toxic if swallowed.

Exercise care in handing the battery pack in order not to short it with conducting materials such as rings, bracelets and keys. The battery or conductor may overheat and cause burns.

4

Charge the battery pack provided with or identified for use with this product only in accordance with the instructions and limitations specified in the instruction manual provided for this product.

Observe proper polarity orientation between the battery pack and battery charger.

5#8'"6*'5'" +05647%6+105

+0641&7%6+10

Thank you for purchasing a RadioShack 900 MHz Cordless Telephone. Your telephone provides excellent clarity and range and integrates Caller ID, Call Waiting ID, and a digital answering system into one space-savingdevice. The 900 MHz band provides less interference, clearer sound, and greater range than 46/49 MHz cordless telephones.

The digital answering system provides clear reliable messaging with call screening, day/time stamp, call counter, remote access and instant skip or replay messaging.

The Caller ID records each caller’s name (if available in your area), telephone number, and the date and time of the call, as provided by your local phone company to Caller ID service subscribers. #"

+/2146#06"%#..'4"+&" +0(14/#6+10

To use Caller ID and Call Waiting, you must be in an area where those services are available and you must subscribe to those services through your local phone company. Where Caller ID is offered, one or more options are generally available:

#"+/2146#06"#

Cordless phones such as this one require AC power to operate. When the AC power is off, you cannot dial out or receive incoming calls using your phone. To be safe, you should also have a phone that does not need AC power to operate (not a cordless phone) so you can still make and receive calls if there is an AC power failure.

When AC power is lost, the phone loses the security access-protectioncode connection between the base and the handset. When power is restored, put the both handsets on the base briefly to restore this connection.

Introduction

5

Information ID Caller Important

caller’s number only

caller’s name only

caller’s name and number

If you subscribe to Call Waiting ID and Caller ID, the system can show you the incoming caller information, even when you are already talking on the phone.

4'#&"6*+5"$'(14'"+056#..#6+10

We have designed your phone to conform to federal regulations and you can connect it to most phone lines. However, each device that you connect to the telephone line draws power from the line. We refer to this power draw as the phone’s ringer equivalence number, or REN. The REN is on the bottom of your phone.

If you use more than one phone or other device on the line, add up all the RENs. If the total is more than five (three in rural areas), your phones might not ring. If ringer operation is impaired, remove one of the devices from the line.

The digital answering system stores up to 16 minutes of messages on a computer chip and records each message’s day and time. This gives you advanced capabilities over tape-basedanswering machines:

You can delete individual messages and save the rest.

There are no tapes to bother with and no tape mechanisms to wear out.

The remote operation feature lets you operate your answering system from a touch-tonephone (or from a rotary phone with a pocket tone dialer).

6

+056#..#6+10

 

/1706+0)"6*'"2*10'

."%#76+10".

You can place the phone on a desk or table, mount

it on a standard wall plate, or directly on a wall.

You must use a

 

Choose a location that is:

! Class 2 power

• near an AC outlet

source that

supplies 9V DC and

• near a modular telephone line jack

delivers at least 350 mA.

• out of the way of normal activities

Its center tip must be set

• away from electrical machinery, electrical

to positive and its plug

must fit the phone's DC

appliances, metal walls or filing cabinets,

IN 9V jack. The supplied

wireless intercoms, alarms, and room monitors

adapter meets these

• away from other cordless phones

specifications. Using an

adapter that does not

 

You can try different locations to see which provides

meet these

the best performance. .#

specifications could

damage the phone or

 

Your telephone connects directly to a modular

the adapter.

telephone line jack. If your telephone wiring does

• Always connect the AC

not have a modular jack, you can update the wiring

adapter to the phone

yourself using jacks and adapters (available at your

before you connect it to

local RadioShack store or online at

AC power. When you

RadioShack.com), or have the telephone company

finish, disconnect the

adapter from AC power

update the wiring for you. You must use compatible

before you disconnect it

modular jacks that are compliant with Part 68 of

from the phone.

FCC Rules. The USOC number of the jack to be

 

installed is RJ11C (RJ11W for a wall plate).

 

1P"C"&GUM"6QR

DC IN 9V

1. Plug one end of the supplied long modular cord

TEL LINE

 

into the TEL LINE jack on the base’s back.

 

2. Plug the modular cord’s other end into a

 

modular telephone line jack.

 

3. Insert the supplied AC adapter’s barrel plug

 

into the DC IN 9V jack on the back.

 

4. Route the adapter’s cord through the strain relief slot on the base’s bottom.

Installation

7

DC IN 9V
TEL LINE

Installation

5.Plug the adapter into a standard AC outlet.

6.Lift the base’s antenna to a vertical position.

 

1P"C"9CNN"2NCVG"QT"9CNN

DC IN 9V

To mount the phone directly on a wall, you need two

TEL LINE screws (not supplied) with heads that fit into the

 

keyhole slots on the base. Drill two holes 315/16

 

inches apart. Thread a screw into each hole,

 

leaving the heads extended about 1/8 inch.

1. Plug one end of the supplied modular cord (short for a wall plate, long for direct wall mounting) into the jack on the base’s back.

2. Insert the supplied AC adapter’s barrel plug into the jack.

3.Route the adapter and modular cords through the base’s grooves.

4. For a wall plate, plug the modular cord’s other end into the wall plate jack, then align the base’s keyhole slots with the wall plate studs and slide the base downward to secure it.

For direct wall mounting, align the base’s keyhole slots with the mounting screws and slide the base downward to secure it.

5. Plug the adapter into a standard AC outlet.

DC IN 9V

6. Lift the base’s antenna to a vertical position.

+056#..+0)"6*'"%*#4)+0)" %4#&.'

1.Insert the supplied AC adapter’s barrel plug into the DC IN 9V jack on the back of the charger.

2. Route the cord through the strain relief slot and plug the adapter into a standard AC outlet.

8

%100'%6+0)."%*#4)+0)"#0&" 4'2.#%+0)"6*'"$#66'4;"2#%-

The phone comes with a rechargeable Ni-Cd(nickel-cadmium)battery pack installed in each handset, but not connected. Before using your phone, you must connect the battery packs, then charge them for about 24 hours.

1.Press down and slide off the battery pack compartment cover.

2.Lift the battery pack out of the compartment.

3.Plug the battery pack’s connector into the

socket in the compartment. The connector fits only one way.

4. Put the battery pack in the compartment.

5. Replace the cover.

To charge the battery packs, place one handset on the base, face up or down. The base’s CHARGE LED lights. Place the other handset on the charging cradle. The cradle’s CHARGE LED lights#"

Recharge the battery pack when Bemý8Wjj[hoý flashes.±ý

When you first use the phone after charging or recharging the battery packs, the phone might not work and you might hear error beeps. If this happens, return the handset to the base for about 5 seconds to reset the security access-protectioncode.

Using a pencil eraser, clean the charging contacts on the handset, the base, and the charger about once a month.

#"+/2146#06"#

Be sure the battery pack is properly connected before you try to charge it. The CHARGE LED lights when the handset is on the base or cradle even if the battery pack is not connected properly.

±"016'"±"

If the phone does not work, recharge the battery pack. (The battery power might be too low for the display to operate.)

If the battery pack becomes weak during a

call, the handset beeps

andýBemý8Wjj[ho

flashes. When this happens, you cannot make a call on the phone until you recharge the battery pack.

If the battery pack is completely discharged or the base loses power while the handset is away from it, place the handset on the base to reset the security access-protectioncode. If it was the handset that lost power, recharge the battery pack.

Installation

9

Installation

ýR"9#40+0)ýR"

Dispose of the old battery pack promptly and properly. Do not burn or bury it (see “Battery Safety Instructions” on Page 4 for additional information on proper battery handling).

About once a month, fully discharge the battery

pack by keeping the handset off the base or cradle until Bemý8Wjj[ho flashes. Otherwise, the battery

pack loses its ability to fully recharge.

The supplied battery pack should last about a year. If the battery pack does not hold a charge for more than 2 hours after an overnight charge, replace it with a new 3.6V, 600 mAh battery pack with a connector that fits the socket in the battery compartment. You can order a replacement battery pack through your local RadioShack store (or online at RadioShack.com). Install the new battery pack and charge it for about 24 hours.

If you have trouble replacing the battery pack, take the phone to your local RadioShack for assistance.

4GE[ENKPI"0K/%F"$CVVGTKGU0

The EPA certified RBRC®Battery Recycling Seal on thenickel-cadmium(Ni-Cd)battery indicates RadioShack is voluntarily participating in an industry program to collect and recycle these

batteries at the end of their useful life, when taken out of service in the United States or Canada. The RBRC program provides a convenient alternative to placing used Ni-Cdbatteries into the trash or the municipal waste stream, which may be illegal in your area. Please call1-800-THE-SHACK(1-800-843-7422)for information onNi-Cdbattery recycling and disposal bans/restrictions in your area. RadioShack’s involvement in this program is part of the company’s commitment to preserving our environment and conserving our natural resources.

4')+56'4+0)"6*'"5'%10&" *#0&5'6

The handset placed on the base during the charging process automatically registered with the base, and >I' appears on the upper right of the

10

display. The handset charged in the cradle must also be registered with the base prior to use.

Place the second handset on the base. The base’s CHARGE LED flashes. When the registration is complete >I( appears in the second handset’s display.±

5'66+0)"6*'"&+#.+0)"/1&'

Your phone comes set for tone dialing. If you have pulse service, you need to change the dialing mode.

If you are not sure which type of service you have, do this test:

1.Lift the handset, press TALK/FLASH, and listen for a dial tone.

2.Press any number other than 0 or, if required, an outside line access code (9, for example).

If the dial tone stops, you have touch-tone service.

If the dial tone continues, you have pulse service.

Once you have determined which type of service you have, set the dialing mode. Use handset HS1 to set the dialing mode.±

1.Press END to hang up the phone if necessary, then hold downCID/MENU until the selection screen appears.

2.Press 4 or 9three times to select:_Wb.

3.Press CH/SEL to toggle betweenJed[ýandFkbi[.

±ý

4.To store the new setting, press END, and return the handset to the base.

±"016'"±"

Registering the Second

Handset

Once registered, you may charge HS1 and HS2 on either the base or the charging cradle.

When a power failure occurs, or the base unit’s power is disconnected for longer than one hour, both handsets will need to be re-registered.

Setting the Dialing Mode

You cannot use HS2 to set the dialing mode. Check the handsets’ displays to distinguish between HS1 and HS2.

The phone exits setting mode if a call or page is received, or if you press

END.

Installation

11

Installation

±"016'"±"

The phone exits the setting mode if you:

wait more than 2 seconds between key presses

receive an incoming call

press PLAY/STOP

press TALK/FLASHon the handset

Start again at Step 1.

If the battery power is too low, the dial mode might reset to tone. If you are on a pulse line and cannot make a call, try re-settingthe dialing mode to pulse.

5'66+0)"6*'"*#0&5'6N5"4+0)'4" 610'181.7/'

You can select one of the handsets’ four different ringer tone/volume settings or turn the ringers off. You can also select a different tone/volume for each handset.

At any time, except during a call, repeatedly press 8 or 9 to select the desired ringer setting. Each

time you press a button, the phone rings at the selected setting and H_d]ýJof[ý7 >_]^,H_d]ýJof[ý7ý Bem,H_d]ýJof[ý8ý>_]^,H_d]ýJof[ý8ýBem,ýorH_d][hýE\\ý

appears.

6740+0)"6*'"$#5'N5"4+0)'4" 1011(("

You can set the base’s ringer to high or low, or turn it off.

1.Press SET/RING. The phone’s currently set ring

sounds, and the current setting appears. When

the ringer is set to E<, the phone announces “Off.” ±

2.Repeatedly press SET/RING to change the

current setting. The system rings at each setting change and >_,Be, orE\ appears.

3.Press PLAY/STOP to store and exit the setting mode.

Even when you turn off the base’s ringer, you can still make or receive calls using this phone. Telephones on the same line and the handset (if its ringer is not turned off) still ring when there is an incoming call.

12

5'66+0)"#761"6#.-

Your phone is preset so you must press TALK/ FLASH to answer a call. With Auto Talk turned on, you can answer a call by just lifting the handset from the baseor cradle. Auto Talk is independent in each handset. You can set each handset differently.

1.Lift the handset and hold down CID/MENU until the setup menu appears.

2.Press CH/SEL to change the Auto Talk setting.Ed orE\\ appears.

3.To clear the screen when you finish, press END or return the handset to the base or cradle.

6740+0)"%#..'4"+&1%#.." 9#+6+0)"1011((

If you have Call Waiting and Caller ID service, you can set the system to show Caller ID information for an incoming call even while you are on the phone.

1.Lift the handset and hold down CID/MENU until the menu appears.±

2.Press 2 or9 to select9?:9Mý(Caller ID/Call Waiting).

3.Press CH/SEL to change the Caller ID/Call Waiting setting.Ed orE\\ appears.

4.Press END and return the handset to the base to store the new setting.

5614+0)";174"#4'#"%1&'

You can store your local area code in the phone’s Caller ID record so the area code does not appear if the received call is from your local area. If for some reason you need to dial the area code (or store it in memory), you can add it afterwards. See “Adding/ Deleting the Area Code” on Page 24.±ý

Installation

±"016'"±"

Turning Caller ID/Call Waiting On/Off

This setting must be made from HS1. The CIDCW menu does not appear on HS2.

Storing Your Area Code

If your calling area requires 10-digitdialing (including area code), do not enter the area code.

The area code setting is independent in each handset. You can set either handset to a different area code.

13

Operation Telephone

±"016'"±"

If an area code is already stored, it appears on the display. To delete the area code, press TRSF/DEL three times, then enter your area code. Or you can use6/TONE or#7 to move the cursor and edit the area code

1.Lift the handset and hold down CID/MENU until the menu appears.

2.Press 3 or9 twice to selectý7h[Wý9eZ[.

3.Press CH/SEL, then enter yourthree-digitarea

code. If you make a mistake, repeatedly press6/TONE or #7 to move the cursor over the

incorrect digit, then enter the correct number.

±ý

4.Press CH/SEL to store the area code, then pressEND or return the handset to the base or cradle to clear the display.

6'.'2*10'"12'4#6+10

/#-+0)"#0&"4'%'+8+0)"%#..5

1.To make a call, lift the handset and press TALK/ FLASH.9edd[Yj_d], thenJWba and the current volume setting (see “Setting the Handset Volume” on Page 15) appear on the handset.

If you set the ringer to off, 2H_d][hýE<<4 appears under the volume setting. The base’s CHARGE LED lights.

2.Dial the number. The number appears on the handset as you dial, then the call’s elapsed time appears.

You can also dial the number before you press TALK/FLASH. If you make a mistake, repeatedly pressTRSF/DEL to erase the wrong entry, then enter the correct number. Hold downTRSF/DEL to delete the entire number.

When you receive a call, ?dYec_d]ý9Wbbýappears. Lift the handset from the base or cradle and pressTALK/FLASH. If auto talk is on, just lift the handset from the base or cradle. If the handset is away from the base or cradle, pressTALK/FLASH or any

14

number including or #.9edd[Yj_d], thenJWba and the current volume setting appears.

To end a call, place the handset on the base or cradle, or press END.

5'.'%6+0)"6*'"%*#00'.

The phone scans 20 channels (frequency pairs used between the base and the handset) and automatically selects a clear channel when you make or receive a call.

If you hear other conversations or excessive noise during a call, press CH/SEL to select a different channel.IYWdd_d] appears as your phone searches for a clear channel.

If the handset is too far from the base, the channel might not change. Move closer to the base and try again.

5'66+0)"6*'"*#0&5'6"81.7/'

To adjust the handset’s volume during a call, press

8 or 9 on the handset until you reach the desired volume level.Lebkc[ýCWn_ckc,Lebkc[ý>_]^,Lebkc[ý C[Z_kc, orLebkc[ýBem appears.

When you press 8 while the setting isLebkc[ý CWn_ckc (or9 while the setting isLebkc[ýBem) the

handset beeps and the setting does not change.

The volume setting is maintained even after you hang up the phone.

75+0)"(.#5*

Flash performs the electronic equivalent of a switchhook operation for special services, such as Call Waiting.

For example, if you have Call Waiting, press TALK/ FLASH to answer an incoming call without

Telephone Operation

15

±"016'"±"

The redial memory holds up to 32 digits, so you can redial long-distance,as well as local numbers.

The redial memory also holds pause entries (see “Entering a Pause” on Page 20).

Operation Telephone

disconnecting the current call. Press TALK/FLASH again to return to the first call.

If you do not have any special phone services, pressing TALK/FLASH might disconnect the current call.

75+0)"4'&+#.

To quickly dial the last number dialed, lift the handset and press RDL/PAUSE, then press TALK/ FLASH. You can also press RDL/PAUSEafter pressing TALK/FLASH. ±ý

/76+0)"6*'"4+0)'4

To temporarily mute the ringer’s tone when you receive a call with the handset off the base, press END. The ringer automatically turns back on when you receive another call.

75+0)"610'"5'48+%'5"10"#"27.5'"

.+0'

Some special services, such as bank-by-phone,require tone signals. If you have pulse service, you can still use these special tone services. Dial the service’s main number. When the service answers, press6/TONE. Any additional numbers you dial are sent as tone signals.

When you hang up, the phone automatically resets to pulse dialing.

2#)+0)

To page the person who has a handset or to locate the handsets when the phone is not in use, press PAGE on the base. Both handsets beep for about one minute. To stop it from beeping sooner, press any key on the handset. PressPAGE again to stop the paging at the base.

16

64#05('44+0)"#"%#..

You can transfer an outside call from one handset to the other.±

Press TRSF/DEL during a call. The call is automatically put on hold, and the transfer tone sounds.

Pick up the other handset from the base or cradle and press TALK/FLASH. If auto talk is on, just pick up the handset. If the handset is away from the base or cradle, pressTALK/FLASH or any number key including* or#. The transfer tone stops.

75+0)"#"*'#&5'6

You can connect an optional headset with a 3/32- inch(2.5-mm)plug. Contact RadioShack for a suitable headset.

To connect the headset, open the rubber cover on the side of the handset, then insert the headset’s plug into the jack.

When you finish using the headset, disconnect it from the handset and close the rubber cover to protect the jack.±ý

/'/14;"&+#.+0)

You can store up to 10 phone numbers and names in each handset’s memory (10 in one handset and an additional 10 in the other), then dial a stored number by entering its memory location number. Each number can be up to 20 digits, and each name can be up to 14 characters.

5VQTKPI"C"0COG"CPF"0WODGT"KP" /GOQT[

When you are storing a number in memory, an error tone sounds and the phone exits the storing process if you wait more than 30 seconds between each keypress. If you receive a call during memory entry, the phone exits the storing process.

±"016'"±"

Transferring a Call

You cannot transfer a call to the base’s answering machine.

Only one handset can talk at one time. You cannot accomplish a 3-wayconference call, or make a call while the other handset is in use.

To cancel the transfer, press TRSF/DEL orTALK/FLASH.

If a transferred call is not answered within five minutes, the call is disconnected.

Using a Headset

Connecting a headset disconnects the handset’s earpiece and microphone.

8 or 9 on the handset also controls the connected headset’s volume.

If you place the handset on the base to recharge it while the headset is connected, be sure the handset seats properly.

With a headset connected, you make or answer calls as usual using the keys on the handset.

You can use an optional handset holder (available from RadioShack) to hang the handset on your belt for greater convenience.

Telephone Operation

17

Operation Telephone

°"*+06"°"

To select the desired letter, refer to the letters on the number keys. Press once for the first uppercase letter, twice for the second letter, and so on. To enter a lowercase letter, press four or five times for the first lowercase letter, five or six times for the second letter, and so on.

For example, to enter John: press5 once; upper case@ appears. Then press6 six times; lower casee appears. Press4 five times; lower case^ appears. Finally, press6 five times; lower cased appears.

1.Lift the handset.

2.Hold down MEM untilC[cehoýIjeh[ and a list of memory location numbers appear.

3.Select a memory location (10)by pressing a number or repeatedly pressing9 or8.

4.Press CH/SEL.Ijeh[ýDWc[ appears. If you do not want to enter a name, skip to Step 6.

5.To enter a name, use the number keys.

To enter two letters from the same key in a row, press #/7 to move the cursor to the next position. For example to enter AB, press 2 so 7 appears. Then press #/7. The cursor moves to the next position. Press 2 twice so 8 appears.

°

To enter a space, press #/7 twice without entering any character.

To enter a number, repeatedly press the corresponding number key until the number appears.

To enter a special character, use 0. Each time you press 0, the following characters appear in this order:

çý#ý&ýâýá(space) &

If you make a mistake, use 6/TONE or #7 to move the cursor over the error, then enter the correct character, or press TRSF/DEL to delete a character. Hold down TRSF/DEL to delete all characters.

6.Press CH/SEL.Ijeh[ýDkcX[hýappears.

7.Enter the phone number and any tone or pause entries (see “Using Tone Services on a Pulse

18

Line” on Page 16 and “Entering a Pause” on Page 20). ±ý

8.Press CH/SEL. The phone beeps andC[cehoýdý Ijeh[Z (d is the memory location number) appears.

C[cehoýIjeh[ reappears. Repeat Steps3–8to store more numbers.

9.When you finish, press END.

To replace a stored number, store a new one in its place.

'FKVKPI"QT"&GNGVKPI"C"0WODGT"KP" /GOQT[

1.Lift the handset.

2.Hold down MEM untilC[cehoýIjeh[ and a list of memory location numbers appear.

3.Choose a memory location (10)by pressing a number or by repeatedly pressing 8 or 9.

4.Press CH/SEL. Press 8 or 9 to select one of three options, then pressCH/SEL to confirm your selection.

;Z_jýC[cehoýd — Edit the record as described in Steps 5 through 8 of “Storing a Name and Number in Memory” on Page 17.

:[b[j[ýC[cehoýd — The display prompts you to confirm the deletion. Press 8 to move the cursor toO[i, then pressCH/SEL orTRSF/DEL. The phone beeps, andC[cehoýdý:[b[j[Z appears.

=eý8WYa — Returns you to the list of memory numbers.

±"016'"±"

Each tone or pause entry uses one digit of memory.

Telephone Operation

19

Operation Telephone

'PVGTKPI"C"2CWUG

Some telephone systems require you to dial an access code (9, for example) and wait for a second dial tone before you can dial an outside number. You can store the access code with the phone number. However, you should also store a pause after the access code to allow the outside line time to connect.

To enter a 2-secondpause, pressRDL/PAUSE.F appears. You can add more pause entries for a longer pause.

4GXKGYKPI"/GOQT["0WODGTU

To review your memory numbers, press MEM. The

list of memory location numbers ('&)appears with the name stored with each number (or2C[cehoýd4 if you did not store a name).

To see the stored phone numbers, press #/7. An arrow to the right of the number means it is longer than 14 digits. Press #7 again to see the rest of the number. Repeatedly press 6/TONE to return to the name display.

To exit the memory number list, press END.

To see a stored name and phone number at the same time, press CH/SEL when the cursor is by a memory location number. To exit this display, hold down TRSF/DEL until the screen clears, or press

END.

&KCNKPI"C"/GOQT["0WODGT

1.Lift the handset and press MEM to dial a stored memory number. The list of memory location numbers appears.

2.Choose a memory location (09)by pressing a number or by repeatedly pressing8 or 9, then pressTALK/FLASH.

20