Radio Shack 43-3704 User Manual

Size:
805.16 Kb
Download

5.8 GHz Dual-HandsetExpandable

2-LineCordless Telephone with Digital Answerer

43-3704

Memo Recording — lets you leave messages for yourself or others in your home or office, or record your phone conversations. (See“Voice memo” on page 66.)

Call Screening — lets you listen as a caller leaves a message. (See“Screening a call” on page 62.)

Speakerphone — lets you conduct ahands-freeconversation using the handset.

Handset Remote Operation — lets you listen to your incoming messages from the handset. (See “Remote Operation” on page 67.)

Message Alertbeeps when you have new incoming message. (See“Setting the message alert” on page 60.)

Convenient Extension Placement — lets you place another handset in addition to the supplied, anywhere you have an AC outlet, regardless of phone jack location.

Call Waiting/Caller ID — lets you answer a call even when you’re on the phone and see who’s calling before you answer.

2-line operation — lets you have one handset talking on Line 1 while another handset participate in a3-wayconference on Line 2 (you must have a2-linesubscription from your phone company).

 

! IMPORTANT!

If an icon appears at the end of a paragraph, go to the box on that page with the

corresponding icon for pertinent information.

o — Warning! — Important

!— CautionÔ — Note

 

 

OWNER’S MANUAL

Please read before using this equipment.

© 2004 RadioShack Corporation.

All Rights Reserved.

RadioShack and RadioShack.com are trademarks used by RadioShack Corporation.

ENERGYSTAR and the ENERGYSTAR certification mark are registered US marks.

DirectLink is a registered trademark of Uniden Corporation.

CONTENTS

Introduction ...................................

3

Important Information ....................

4

FCC Statement ..................................

4

Surge Protection ................................

5

Important Safety Instructions ........

6

Important Caller ID Information .....

7

Read This Before Installation .............

7

Installation .....................................

8

Selecting a Location ..........................

8

Connecting/Charging the Battery

 

Pack ..............................................

11

Installing a Beltclip ...........................

13

Using a Headset ..............................

13

Display and Icons .......................

14

Animation Displays ..........................

14

Soft Key Function .......................

15

Main Menu Options .....................

16

Default Settings ...............................

16

Setting Menu Options .................

17

Using the Interface ...........................

17

De-register the Handset ...................

30

Using Your Phone .......................

30

Making a call ....................................

30

Receiving a call ................................

31

Hanging Up ......................................

32

Call Waiting ......................................

32

Placing a Call on Hold .....................

32

Redialing a Call ................................

32

Adjusting the Handset Earpiece and

 

Speaker Volume ...........................

34

Do Not Disturb (DND) ......................

34

Mute Microphone .............................

35

Tone Dialing Switch Over .................

35

Travelling Out-of-Range ...................

35

Privacy Mode ...................................

35

Conferencing ...................................

36

Flash and Call Waiting .....................

37

Find Handset ...................................

37

Phonebook ..................................

38

Storing Phone Numbers, Names,

 

Distinctive Rings, and Speed

 

Dial ................................................

38

Steps for Entering Names and

 

Special Characters .......................

39

Viewing the Phonebook ...................

40

Making Calls Using the

 

Phonebook ....................................

41

Speed Dialing ..................................

41

Editing or Erasing a Data .................

42

Copying Phonebook Locations ........

43

Testing Stored Emergency

 

Numbers .......................................

44

Caller ID ......................................

45

Caller ID and CIDCW (Caller ID on Call

Waiting) ........................................

45

Viewing the Caller ID List ................

46

Deleting a Caller ID Message .........

47

Using the Caller ID Message List ....

47

Call Waiting Deluxe Features ..........

49

Expanding Your Phone ...............

50

Register the Handset to the Base ...

50

Using the DirectLink Mode ..............

51

Intercom/Call Transfer Feature .......

51

The Integrated Answering

 

Device ........................................

54

Features ..........................................

54

Turning the Answering System

 

On/Off ...........................................

55

Setting up Your Answering

 

System .........................................

55

Adjusting the Speaker Volume

 

Level .............................................

56

NEW MESSAGE LED .....................

57

Using Your Answering System ........

63

Remote Operation ...........................

67

Troubleshooting ..........................

71

Care ............................................

73

Service and Repair .....................

73

Note about Handset-Base

 

Registration ................................

74

2

INTRODUCTION

Thank you for purchasing a RadioShack 5.8 GHz Dual Handset Expandable 2-LineCordless Telephone. Unlike other conventional cordless telephones, your telephone supports up to two handsets on a single telephone line. You can add a handset to any room in your home or office that has an AC outlet. No more running to the other end of the house to answer the phone! You can transfer outside calls to another handset. If you subscribe to Call Waiting with Caller ID, the phone shows you the incoming caller information, even when you are already talking on the phone.

The digital answering system stores up to 12 minutes of messages (for each line) on a computer chip and records each message’s day and time. This gives you advanced capabilities over tape-basedanswering machines:

You can delete individual messages and save the rest.

There are no tapes to bother with and no tape mechanisms to wear out.

The remote operation feature lets you operate your answering system from a touch-tonephone (or from a rotary phone with a pocket tone dialer).

Cordless phones require AC power to operate. When the power is off, you cannot make or receive calls by using your phone. You should also have a phone that does not need AC power to operate (not a cordless phone), so you can still make and receive calls if there is an AC power failure. !

!IMPORTANT !

Your phone operates on standard radio frequencies as allocated by the FCC.

It is possible for other radio units operating nearby on similar frequencies to unintentionally intercept your conversation or cause interference. This possible lack of privacy can occur with any cordless phone.

Introduction

3

Information Important

 

 

 

IMPORTANT

 

 

 

INFORMATION

 

 

 

This telephone has been tested and found

 

 

 

to comply with all applicable UL and FCC

As an ENERGYSTAR Partner,

standards.

 

RadioShack Corporation has

FCC STATEMENT

determined that this product

meets the ENERGYSTAR

This equipment complies with Part 68 of the

guidelines for energy

FCC rules and the requirements adopted by the

efficiency.

ACTA. On the base of this equipment is a label

 

 

 

that contains, among other information, a

 

 

 

product identifier in the format

 

 

 

US:AAAEQ##TXXXX. If requested, this number

 

 

 

must be provided to the telephone company.

 

 

 

Your phone is not intended to be used with

 

 

 

party-linesystems. Connection to party line

 

 

 

service is subject to state tariffs. Contact the

 

 

 

state public utility commission, public service

 

 

 

commission, or corporation commission for

 

 

 

information. Ô

The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g.,

Ô NOTE Ô 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label.

You must not connect your

 

If you use more than one phone or other device

phone to:

 

on the line, add up all of the RENs. If the total is

coin-operatedsystems

 

more than five (three in rural areas), your

most electronic key

 

telephones might not ring. If ringer operation is

 

impaired, remove a device from the line.

 

telephone systems

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

WARNING: To reduce the risk of

 

 

CAUTION.

!

 

 

CAUTION: TO REDUCE THE RISK OF ELECTRIC

fire or shock hazard, do not expose

 

 

 

 

SHOCK, DO NOT REMOVE COVER OR BACK. NO USER-

this product to rain or moisture.

 

 

RISK OF ELECTRIC

 

 

SERVICEABLE PARTS INSIDE. REFER SERVICING TO

 

 

 

 

SHOCK DO NOT OPEN

 

 

QUALIFIED PERSONNEL.

 

 

 

 

 

 

 

 

 

 

 

 

 

The lightning symbol is intended to alert you to the presence of

 

 

 

The exclamation symbol is intended to inform you that important operating

 

uninsulated dangerous voltage within this product’s enclosure that

 

 

!

and maintenance instructions are included in the literature accompanying

 

might be of sufficient magnitude to constitute a risk of electric shock.

 

 

this product.

 

Do not open the product’s case.

 

 

 

 

 

 

 

 

4

In the unlikely event that your phone causes problems on the phone line, the phone company can temporarily discontinue your service. If this happens, the phone company attempts to notify you in advance. If advance notice is not practical, the phone company notifies you as soon as possible and advises you of your right to file a complaint with the FCC.

Also, the phone company can make changes to its lines, equipment, operations, or procedures that could affect the operation of this phone. The telephone company notifies you of these changes in advance, so you can take the necessary steps to prevent interruption of your telephone service.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Privacy of communications, may not be ensured when using this phone.

To insure the safety of users, the FCC has established criteria for the amount of radio frequency energy various products may produce depending on their intended usage. This product has been tested and found to comply with the FCC’s exposure criteria. For body worn operation, the FCC RF exposure guidelines were also met when used with the RadioShack accessories supplied or designed for this product. Use of other accessories may not ensure compliance with FCC RF exposure guidelines and should be avoided.

SURGEPROTECTION

Your telephone has built-inprotection circuits to reduce the risk of damage from surges in telephone line and power line current. These protection circuits meet or exceed the FCC requirements. However, lightning striking the telephone or power lines can damage your telephone.

Lightning damage is not common. Nevertheless, if you live in an area that has severe electrical storms, we suggest that you unplug your phone when storms approach to reduce the possibility of damage.

Important Information

5

IMPORTANT SAFETY INSTRUCTIONS

When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:

1.Do not use this product near water, for example, near a bathtub, wash bowl, kitchen sink, or laundry tub, in a wet basement or near a swimming pool.

2.Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.

3.Do not use the telephone to report a gas leak in the vicinity of the leak.

4.Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special disposal instructions.

SAVE THESE INSTRUCTIONS

Instructions Safety Important

6

IMPORTANT CALLER ID INFORMATION

To use Caller ID and Call Waiting, you must be in an area where those services are available and you must subscribe to those services through your local phone company. Where Caller ID is offered, one or more options are generally available:

caller’s number only

caller’s name only

caller’s name and number

If you subscribe to Call Waiting ID and Caller ID, the system can show you the incoming caller information, even when you are already talking on the phone.

READTHISBEFOREINSTALLATION

We have designed your phone to conform to federal regulations and you can connect it to most phone lines. However, each device that you connect to the telephone line draws power from the line. We refer to this power draw as the phone’s ringer equivalence number, or REN. The REN is on the bottom of your phone.

Important Caller ID Information

7

Installation

Ô NOTEÔ

If your home has specially wired alarm equipment connected to the telephone line, be sure that installing the system does not disable your alarm equipment.

If you have questions about what will disable alarm equipment, contact your telephone company or a qualified installer.

INSTALLATION

Before using your phone, carefully peel the protective film off the display. The film protects the handset window during shipment and is not necessary for use.

SELECTING ALOCATION

You can place the phone’s base on a desk or table, or mount it on a standard wall plate or directly on a wall. Select a location that is:Ô

near an accessible AC outlet

near a telephone line jack

out of the way of normal activities

away from electrical machinery, electrical appliances, metal walls or filing cabinets, wireless intercoms, alarms, and room monitors

away from other cordless phones

The base’s location affects the handset’s range. If you have a choice of several locations, try each to see which provides the best performance.

The handset antenna is located on the back, above the ringer speaker. For maximum communication range, do not hold the handset in such a way as to cover the antenna by your hand. Also, place the handset in the upright position while not in use so the antenna can pick up the signals from the base.

When there is obstacle such as metal or concrete wall between the handset and the base, the operation might be affected. Try to keep free from obstruction.

8

Your telephone connects directly to a modular telephone line jack. If your telephone wiring does not have a modular jack, you can update the wiring yourself using jacks and adapters (available at your local RadioShack store), or have the telephone company update the wiring for you. Ô

On a Desk Top

1.Plug one end of the supplied long modular cord into the TEL LINE 1/2 jack on the back of the base.

For 2 line subscriptions,

If the two phone lines are in one modular jack, connect using TEL LINE 1/2jack.

If the two phone lines are on two separate modular jacks, connect using both TEL LINE 1/2and TEL LINE 2jacks.

2.Plug the modular cord’s other end into a modular phone line jack.

3.Insert the supplied AC adapter’s barrel plug into the DC IN 9V jack on the back of the base.!

4.Route the adapter’s cord through the strain relief slot on the base, then plug the adapter into a standard AC outlet.

On a Wall Plate or Wall

To mount the phone directly on a wall, you need two screws (not supplied) with heads that fit into the keyhole slots on the base.

Drill two holes 315/16 inches apart. Thread a screw into each hole, letting the heads extend about1/8 inch.

Ô NOTEÔ

The USOC number of the jack to be installed is RJ11C (or RJ11W for a wall plate jack).

!CAUTION!

You must use

!a Class 2 power source

that supplies 9V DC and delivers at least 400 mA. Its center tip must be set to positive and its plug must fit the phone’s DC IN 9V jack. The supplied adapter meets these specifications. Using an adapter that does not meet these specifications could damage the phone or the adapter.

Installation

9

Installation

To remove, push up

a tab on the wall

mount adapter as shown.

1.Make the AC adapter and the short telephone line cord through the hole on the bracket.

2.Plug one end of the modular cord into the TEL LINE 1/2 jack on the back of the base.

3.Insert the supplied AC adapter’s barrel plug into theDC IN 9V jack on the back of the base.

4.Slide the bracket into the notches on the base.

5.Plug the adapter into a standard AC outlet. Hook the cord on the notch of the bracket.

6.Plug the telephone line cord into the telephone outlet.

7.For a wall plate,

align the base’s keyhole slots with the wall plate studs and slide the base

downward to secure it.

For direct wall mounting, align the base’s keyhole slots with the mounting screws and slide

the base downward to secure it.

10

CONNECTING/CHARGING THEBATTERYPACK

The phone comes with a rechargeable nickel-metalhydride(Ni-MH)battery pack in the handset, but not connected. Before using your phone, you must connect the battery pack, then charge it for about15–20hours.

1.Press down and slide off the battery compartment cover.

2.Lift the battery pack out of the compartment.

3.Plug the battery pack’s connector into the socket in the compartment (the connector fits only one way), then place the battery pack in the compartment.

4.Replace the cover.

To charge the battery pack, place the handset on the base. The CHARGE indicator on the base lights.

Recharge the battery pack when

Low Battery flashes on the display.

If you have trouble replacing the battery pack, take the phone to your local RadioShack for assistance.

Recharging the Battery Pack

If the battery pack becomes weak during a call, Low Battery flashes. When this happens, you cannot make a call until you recharge the battery pack.!

If the display is blank and the phone does not work, recharge the battery pack. (The battery power might be too low to light the display.)

About once a month, fully discharge the battery by keeping the handset off the base until Low Battery flashes on

! IMPORTANT!

Be sure the battery pack is properly connected before you try to charge it. The CHARGE indicator lights when the handset is on the base, even if the battery pack is not connected.

Installation

11

Installation

oWARNINGo

Dispose of the old battery pack promptly and properly. Do not burn or bury it. There is a risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.

the display. Otherwise, the battery pack loses its ability to fully recharge.

Using a damp cloth, clean the charging contacts on the handset about once a month.

If you are not going to use your phone for an extended period, disconnect the battery pack. This increases the battery pack’s usable life.

The supplied battery pack should last for about a year. If the battery pack does not hold a charge for more than 2 hours after an overnight charge, replace it with a new 3.6-volt,800 mAh battery pack with a connector that fits the socket in the battery compartment. You can order a replacement battery pack through RadioShack. Install the

new battery pack and charge it for about 15–20hours.o

12

INSTALLING ABELTCLIP

To attach the beltclip

Insert the beltclip into the holes on each side of the handset. Press down until it clicks.

To remove the beltclip

Pull either side of the beltclip to release the tabs from the holes.

USING AHEADSET

You can make or answer calls with handsfree convenience using an optional headset that has a 3/32-inch(2.5-mm)plug.

RadioShack has a variety of headsets available.

To connect the headset, gently flip open the rubber headset jack cover on the side of the handset, then insert the headset’s plug into the jack. Ô

Connecting a headset disconnects the handset’s earpiece and microphone.

CID/VOL/orREDIAL/P/on the handset also controls the headset’s volume.

With a headset connected, you can make or answer calls as usual using the keys on the handset.

When you finish using the headset, disconnect it from the handset and close the rubber cover to protect the jack.

ÔNOTES Ô

If you place the handset on the base to recharge it while the headset is connected, be sure the handset seats properly.

You can use a handset holder (available from your local RadioShack store) to hang the handset on your belt for greater convenience when using a headset.

Installation

13

Icons and Display

DISPLAY AND ICONS

Example of the standby mode display

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Ringer off icon (when the ringer is off)/ day of the week and

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

time / battery icon

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Handset ID and Banner

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Number of new Caller ID calls received (If there are no new

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Caller ID messages, the Handset ID appears here.)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ICON

 

Appears

 

 

DESCRIPTION

 

 

 

 

 

 

 

 

During

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Standby/

 

Battery icons indicate the handset battery status. This

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

icon changes depending on the battery status (empty,

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Talk

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

low, medium and full).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Standby/

 

The Line icon indicates the line in use or the line received

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Talk

 

a new Caller ID message (Line1 and/or Line2).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Standby/

 

The Ringer off icon indicates that ringer is turned off.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Bell

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Talk

 

The Mute icon appears when you mute the handset.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Talk

 

The Speaker icon appears when the handset speaker

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

phone is used.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Talk

 

The Privacy icon appears when the Privacy Mode is

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

turned on.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Talk

 

The Recording icon appears while recording a

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

conversation

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ANIMATIONDISPLAYS

The handsets have a variety of animation displays. Below are examples of the animation screens and what they mean:

Turning on the phone

Hanging up the phone Confirmation (Done!)

Deleting (Deleted!)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Paging handset

Also, the animation display changes depending on the ringer volume setting.

 

 

]

 

 

 

 

 

Out of Range

Unavailable

Low Battery

 

 

 

 

 

 

14

SOFT KEY FUNCTION

“Soft” keys are keys that change function during the operation of the phone. There are three soft keys on each handset. Soft Keys allow you to:

Access the main menu

Store or edit phone numbers and Caller ID message

The function of each soft key is determined by the icon that appears directly above it. For example, when the handset is in standby mode, pressing soft key 1 will activates Line1. When the handset is in talk mode, pressing soft key 1 displays the list of CWDX option.

Complete information on the features controlled by the soft keys can be found under each feature.

In standby mode

Soft key 1 Soft key 2Soft key 3

In talk mode

Soft key 1 Soft key 2Soft key 3

Soft Key Function

15

Options Menu Main

Ô NOTEÔ

For Global Setup, Answ. Setup, and Deregister HS menu options, make sure the line is not in use and the handsets are within range of the base.

MAIN MENU OPTIONS

Your phone has six main menu options:

DirectLink Mode, Room Monitor, Handset Setup, Answ. Setup, Global Setup, and Deregister HS. Ô

DEFAULTSETTINGS

The default settings set from the factory match the features that most people use. You may not need to change them. However, there are a number of options you must set and entries you must make in memory to take full advantage of all the phone features. The table below lists the default settings.

Function

Default Settings

 

 

Set TEL-LINE

Auto

Ringer Volume

High

Ringer Tone

Line1: Flicker

 

Line2: Clatter

Distinctive Ring

On

Auto Talk

Off

Anykey Answer

Off

Banner

“ ”

Language (LCD)

English

Contrast

level 5

Key touch tone

On

Animation Screen

On

Room Monitor

On

Security code

80

Ring Time

Toll Saver

Recording Time

1 minute

Message alert

Off

Language (Guidance)

English

Call Screen

On

Day & Time

SUN 12:00 AM

CW / CWDX

CW on/CWDX off

Area code

None

Dial Mode

Tone

16

SETTING MENU

OPTIONS

USING THEINTERFACE

Below are some tips for using the software interface on your phone.

Press the MENU soft key to access the main menu.

Use CID/VOL/ or REDIAL/P/ to scroll through options.

Press the OK soft key to make a selection.

Press the BACK soft key to return to the previous screen.

Press END to exit the menu.

If you do not press a key within 30 seconds, the phone will time out and exit the menu mode. When setting Day and Time, the time-outperiod is extended to two minutes.

DirectLink Mode

In DirectLink® mode, a pair of handsets can function as two-wayradios. DirectLink Mode allows two handsets to communicate with each other without the base unit or a telephone line. Use them at sporting events or while shopping to stay in contact with family members or friends. You must set both handsets to DirectLink Mode to activate this feature. Ô

Using DirectLink Mode

1.Press the MENU soft key and select the DirectLink Mode menu.To enter DirectLink mode press [ENTER] appears.

2.Press the ENTER soft key to enter DirectLink mode. You will hear a

Ô NOTEÔ

You must have two handsets to use Direct Link Mode.

Setting Menu Options

17

Options Menu Setting

ÔNOTES Ô

You must have two handsets to use Room Monitor feature.

This feature only works when the handset is within the range of the base.

confirmation tone, and DirectLink Mode Complete appears.

3.To return to normal mode, press the CANCEL soft key and then theOK soft key, or return the handset to the cradle.

Room Monitor

This feature allows you to monitor sounds in another room. Place the handset in the room you wish to monitor; it will function as a microphone. A second handset can be set to function as a remote speaker, allowing you to monitor sounds in the room. Ô

Using Room Monitor

1.Press the MENU soft key and select the Room Monitor menu.Listen to; appears.

2.Select the handset you want to monitor by using CID/VOL/ or REDIAL/P/ .

3.Press the OK soft key.Monitoring appears, and you hear

sounds in the room where the handset is installed.

4.To turn off the Room Monitor, press the END soft key, orEND.

Handset Setup

The following submenu options must be set separately for each handset.

Selecting a Telephone Line

TEL-LINEallows you to set default telephone line. The line you select will be used when you make a call. If you select Auto, the phone will default to whichever line is currently free.

1.Press the MENU soft key. Select the Handset Setup menu, and then the SetTEL-LINEsubmenu.

18

2.Press CID/VOL/ or REDIAL/P/ to select Auto, Line1, or Line2.

3.Press the OK soft key. You will hear a confirmation tone.

Selecting a Ringer Volume

Ringer Volume lets you select one of three ringer volume (Off, Low, or High).

1.Press the MENU soft key. Select the Handset Setup menu, and then the Ringer Volume submenu.

2.Press CID/VOL/ or REDIAL/P/ to select Line1or Line2, and then press the OKsoft key.

3.Press CID/VOL/ or REDIAL/P/ to adjust the ringer settings (Ringer Volume Off, Ringer Volume Low, or Ringer Volume High). You will hear a ringer or melody at the Selected volume (if you select Ringer Volume Off, no ringer or melody will sound).

4.Press the OK soft key. You will hear a confirmation tone.

Selecting a Ringer Tone

Ringer Tone lets you choose from ten ringer tones or ten melodies:

Ringers (Flicker, Clatter, Soft Alert, Wake Up, Light Bug, Beep Boop, Tone Board, Chip Chop, Party Clap, Reminder)

Melodies (Beethoven’s Symphony #9 [Beethoven9], For Elise [Elise], We Wish You A Merry Christmas [MerryXmas], Home Sweet Home [Hm Swt Hm], Lorri Song #6 [Lorri Song], When Irish Eyes Are Smiling [Irish Eyes], Aura Lee, Let Me Call You Sweet Heart

Setting Menu Options

19

Options Menu Setting

[Sweetheart], Star Spangled Banner [Star Spngl], Old MacDonald [Old MacDld])

You must set a separate ringer tone on each handset.

1.Press the MENU soft key. Select the Handset Setup menu, and then the Ringer Tone submenu.

2.Press CID/VOL/ or REDIAL/P/ to select Line1or Line2, and then press the OKsoft key.

3.Press CID/VOL/ or REDIAL/P/ to move the pointer. You will hear the ringer or melody as you scroll through the options.

4.When you reach the ringer tone you want, press the OK soft key. You will hear a confirmation tone.

Distinctive Ringer Setup

Distinctive Ringer allows you to assign a designated ring tone to a stored phonebook number (100 stored locations available). When a call is received and the Caller ID information matches the information in one of the phonebook memory locations, the phone uses the distinctive ring assigned to that particular caller. You can assign distinctive rings to multiple phonebook memory locations. Switching the setting to Distinctive Off disables distinctive ringing: all incoming calls will have a normal ring tone. Switching to Distinctive On activates all programmed distinctive ring memory locations.

1.Press the MENU soft key. Select the Handset Setup menu, and then the Distinctive Ring submenu.

20