Radio Shack 43-3570 User Manual

Size:
347.22 Kb
Download

2.4 GHz Multi-HandsetExpandable Cordless Telephone with Call Waiting/Caller ID

43-3570

Hearing-Aid Compatible — Enables use of the phone with hearing aids that have a T (telephone) switch.

Ample Talk and Standby Time — The supplied battery (when fully charged) provides about seven hours of talk time or ten days of standby time.

Distinctive Ring — Allows you to assign a distinctive ringer to certain memory locations. When an incoming call is received and the Caller ID information matches the information in one of the memory locations, the distinctive ring that has been stored for that particular caller sounds. (See “Distinctive Ringer Setup” on page 18)

Speakerphone — lets you conduct ahands-freeconversation using the handset speaker. (See “Making and Receiving Calls” on page 23)

Convenient Extension Placement — lets you place accessory handsets (up to four total) anywhere you have an AC outlet, regardless of phone jack location.

Call Waiting/Caller ID — lets you answer a call even when you’re on the phone and see who’s calling before you answer.

Handset Walkie-Talkielets you use two handsets likewalkie-talkie,even if you are away from the base unit.

! IMPORTANT!

If an icon appears at the end of a paragraph, go to the box on that page with the

corresponding icon for pertinent information.

o— Warning! — Important

— Caution Ô — Note

 

OWNER’S MANUAL

Please read before using this equipment.

© 2004 RadioShack Corporation.

All Rights Reserved.

RadioShack and RadioShack.com are trademarks used by RadioShack Corporation.

ENERGYSTAR and the ENERGYSTAR certification mark are registered US marks.

DirectLink is a registered trademark of Uniden Corporation.

CONTENTS

Introduction ...................................

3

Important Information ...................

4

FCC Statement ..................................

4

Surge Protection ................................

5

Important Safety Instructions ........

6

Important Caller ID Information ....

7

Read This Before Installation .............

7

Installation .....................................

8

Selecting a Location ..........................

8

Connecting/Charging the Battery

 

Pack ................................................

11

Setting Menu Options .................

13

About the Menu Options ..................

13

Summary of Main Menu Options and

 

Submenu Option ............................

13

Setting Up the Menu ........................

16

Making and Receiving Calls .......

23

Placing a Call on Hold .....................

25

Redialing a Call ................................

25

Adjusting the Handset Ringer,

 

Earpiece and Speaker Volume .......

26

Mute Microphone .............................

27

Tone Dialing Switch over ..................

27

Travelling Out-of-Range ...................

27

Clarity Booster .................................

28

Privacy Mode ...................................

28

Find Handset ...................................

28

Flash and Call Waiting .....................

29

Using One Touch

 

Voice Mail Access ..........................

29

Phonebook ..................................

30

Storing Phone Numbers, Names,

 

Distinctive Rings, and

 

Speed Dial ......................................

30

Steps for Entering Names and

 

Special Characters .........................

31

Viewing the Phonebook ...................

33

Making Calls Using the

 

Phonebook .....................................

34

Speed Dialing ..................................

34

Editing or Erasing Data ....................

35

Chain Dialing ...................................

36

Caller ID ......................................

36

Caller ID and CIDCW (Caller ID on

 

Call Waiting) ...................................

36

Viewing the Caller ID List .................

37

Deleting a Caller ID Message ..........

38

Using the Caller ID Message List ....

39

Call Waiting Deluxe Features ...........

40

Expanding Your Phone ...............

41

Register the Handset to the Base ....

42

Using the DirectLink Mode ...............

43

3-WayConferencing ........................

43

Intercom/Call Transfer Feature ........

44

Installing the Beltclip ...................

46

Using a Headset .........................

46

Troubleshooting ..........................

47

Care ............................................

48

Service and Repair .....................

48

2

INTRODUCTION

Thank you for purchasing a RadioShack 2.4 GHz Multi Handset Expandable Cordless Telephone. Unlike other conventional cordless telephones, your telephone supports up to four handsets on a single telephone line. You can add a handset to any room in your home or office that has an AC outlet. No more running to the other end of the house to answer the phone! You can transfer outside calls to other handsets. If you subscribe to Call Waiting with Caller ID, the phone shows you the incoming caller information, even when you are already talking on the phone.

Cordless phones require AC power to operate. When the power is off, you cannot make or receive calls by using your phone. You should also have a phone that does not need AC power to operate (not a cordless phone), so you can still make and receive calls if there is an AC power failure. !

As an ENERGYSTAR Partner, RadioShack Corporation has determined that this product meets the ENERGYSTAR guidelines for energy efficiency.

!IMPORTANT !

Your phone operates on standard radio frequencies as allocated by the FCC.

It is possible for other radio units operating nearby on similar frequencies to unintentionally intercept your conversation or cause interference. This possible lack of privacy can occur with any cordless phone.

Introduction

3

Information Important

Ô NOTEÔ

You must not connect your phone to:

coin-operatedsystems

most electronic key telephone systems

IMPORTANT

INFORMATION

This telephone has been tested and found to comply with all applicable UL and FCC standards.

FCC STATEMENT

Your telephone compiles with Part 68 of the FCC Rules.Upon request, you must provide the phone’s FCC registration number and REN to your phone company. These numbers are on the base unit.

Your phone is not intended to be used with party-linesystems. Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission, or corporation commission for information. Ô

We have designed your phone to conform to federal regulations, and you can connect it to most telephone lines. However, each phone (and each device, such as a telephone or answering machine) that you connect to the telephone line draws power from the telephone line. We refer to this power draw as the device’s ringer equivalence number, or REN on the back of your phone.

If you use more than one phone or other device on the line, add up all of the RENs. If the total is more than five (three in rural areas), your telephones might not ring. If ringer operation is impaired, remove a device from the line.

WARNING: To reduce the risk of

 

 

CAUTION.

!

 

 

CAUTION: TO REDUCE THE RISK OF ELECTRIC

fire or shock hazard, do not expose

 

 

 

 

SHOCK, DO NOT REMOVE COVER OR BACK. NO USER-

this product to rain or moisture.

 

 

RISK OF ELECTRIC

 

 

SERVICEABLE PARTS INSIDE. REFER SERVICING TO

 

 

 

SHOCK DO NOT OPEN

 

 

QUALIFIED PERSONNEL.

 

 

 

 

 

 

 

 

 

 

The lightning symbol is intended to alert you to the presence of

 

 

 

The exclamation symbol is intended to inform you that important operating

uninsulated dangerous voltage within this product’s enclosure that

 

 

!

and maintenance instructions are included in the literature accompanying

might be of sufficient magnitude to constitute a risk of electric shock.

 

 

this product.

Do not open the product’s case.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

In the unlikely event that your phone causes problems on the phone line, the phone company can temporarily discontinue your service. If this happens, the phone company attempts to notify you in advance. If advance notice is not practical, the phone company notifies you as soon as possible and advises you of your right to file a complaint with the FCC.

Also, the phone company can make changes to its lines, equipment, operations, or procedures that could affect the operation of this phone. The telephone company notifies you of these changes in advance, so you can take the necessary steps to prevent interruption of your telephone service.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Privacy of communications, may not be ensured when using this phone.

SURGEPROTECTION

Your telephone has built-inprotection circuits to reduce the risk of damage from surges in telephone line and power line current. These protection circuits meet or exceed the FCC requirements. However, lightning striking the telephone or power lines can damage your telephone.

Lightning damage is not common. Nevertheless, if you live in an area that has severe electrical storms, we suggest that you unplug your phone when storms approach to reduce the possibility of damage.

Important Information

5

IMPORTANT SAFETY INSTRUCTIONS

When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:

1.Do not use this product near water, for example, near a bathtub, wash bowl, kitchen sink, or laundry tub, in a wet basement or near a swimming pool.

2.Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.

3.Do not use the telephone to report a gas leak in the vicinity of the leak.

4.Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special disposal instructions.

SAVE THESE INSTRUCTIONS

Instructions Safety Important

6

IMPORTANT CALLER ID INFORMATION

To use Caller ID and Call Waiting, you must be in an area where those services are available and you must subscribe to those services through your local phone company. Where Caller ID is offered, one or more options are generally available:

caller’s number only

caller’s name only

caller’s name and number

If you subscribe to Call Waiting ID and Caller ID, the system can show you the incoming caller information, even when you are already talking on the phone.

READTHISBEFOREINSTALLATION

We have designed your phone to conform to federal regulations and you can connect it to most phone lines. However, each device that you connect to the telephone line draws power from the line. We refer to this power draw as the phone’s ringer equivalence number, or REN. The REN is on the bottom of your phone.

If you use more than one phone or other device on the line, add up all the RENs. If the total is more than five (three in rural areas), your phones might not ring. If ringer operation is impaired, remove one of the devices from the line.

Important Caller ID Information

7

Installation

ÔNOTES Ô

If your home has specially wired alarm equipment connected to the telephone line, be sure that installing the system does not disable your alarm equipment. If you have questions about what will disable alarm equipment, contact your telephone company or a qualified installer.

The USOC number of the jack to be installed is RJ11C (or RJ11W for a wall plate jack).

INSTALLATION

Before using your phone, carefully peel the protective film off the display. The film protects the handset window during shipment and is not necessary for use.

SELECTING ALOCATION

You can place the phone’s base on a desk or table, or mount it on a standard wall plate or directly on a wall. Select a location that is:Ô

near an accessible AC outlet

near a telephone line jack

out of the way of normal activities

away from electrical machinery, electrical appliances, metal walls or filing cabinets, wireless intercoms, alarms, and room monitors

away from other cordless phones

The base’s location affects the handset’s range. If you have a choice of several locations, try each to see which provides the best performance.

Your telephone connects directly to a modular telephone line jack. If your telephone wiring does not have a modular jack, you can update the wiring yourself using jacks and adapters (available at your local RadioShack store), or have the telephone company update the wiring for you. You must use compatible modular jacks that are compliant with Part 68 of FCC Rules. Ô

8

On a Desk Top

1.

Plug one end of

TEL

DC IN 9V

 

the supplied long

LINE

 

 

modular cord into

 

 

 

the TEL LINEjack

 

 

 

on the back of the

 

 

 

base.

 

 

2.

Plug the modular

 

 

 

cord’s other end

 

 

 

into a modular

 

 

 

phone line jack.

 

 

3.

Insert the supplied

 

 

 

AC adapter’s

 

 

barrel plug into the DC IN 9V jack on the back of the base.

4.Route the adapter’s cord through the strain relief slot on the base, then plug the adapter into a standard AC outlet.

5.Lift the base’s antenna to a vertical position.

On a Wall Plate or Wall

To mount the phone directly on a wall, you need two screws (not supplied) with heads that fit into the keyhole slots on the base.

Drill two holes 315/16 inches apart. Thread a screw into each hole, letting the heads extend about1/8 inch.

1.Detach the bracket from the bottom of the base.

2.Insert the two

tabs at the top of the narrow end of the supplied bracket into the base’s upper tab slots, then press down on the bracket’s latches

and insert them into the lower slots.

CAUTION

You must use

!a Class 2 power source

that supplies 9V DC and delivers at least 350 mA. Its center tip must be set to positive and its plug must fit the phone’s DC IN 9V jack. The supplied adapter meets these specifications. Using an adapter that does not meet these specifications could damage the phone or the adapter.

Installation

9

Installation

3.Plug one end of the supplied modular cord (short for a wall plate, long for direct wall mounting) into the TEL LINE jack on the base’s back.

4.Insert the supplied AC adapter's barrel plug into the DC IN 9V jack.

5.Route the

adapter and modular cords

through the base’s grooves.

6. For a wall plate, plug the

modular cord’s other end into the wall plate jack, then align the base’s keyhole slots with the wall plate studs and slide the base downward to secure it.

For direct wall

mounting, align the base’s keyhole slots

with the mounting screws and

slide the base downward to secure it.

7.Plug the adapter into a standard AC outlet.

8.Lift the base’s antenna to a vertical position.

10

CONNECTING/CHARGING THEBATTERYPACK

The phone comes with a rechargeable nickel-metalhydride(Ni-MH)battery pack in the handset, but not connected. Before using your phone, you must connect the battery pack, then charge it for about15–20hours.

1.Press down and slide off the battery compartment cover.

2.Lift the battery pack out of the compartment.

3.Plug the battery pack’s connector into the socket in the compartment (the connector fits only one way), then place the battery pack in the compartment.

4.Replace the cover.

To charge the battery pack, place the handset on the base. The CHARGE indicator on the base lights.

Recharge the battery pack when

Low Battery flashes on the display.

If you have trouble replacing the battery pack, take the phone to your local RadioShack for assistance.

Recharging the Battery Pack

If the battery pack becomes weak during a call, Low Battery flashes. When this happens, you cannot make a call until you recharge the battery pack.!

If the display is blank and the phone does not work, recharge the battery pack. (The battery power might be too low to light the display.)

! IMPORTANT!

Be sure the battery pack is properly connected before you try to charge it. The CHARGE indicator lights when the handset is on the base, even if the battery pack is not connected.

Installation

11

Installation

oWARNINGo

Dispose of the old battery pack promptly and properly. Do not burn or bury it. There is a risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.

About once a month, fully discharge the battery by keeping the handset off the base until Low Battery flashes on the display. Otherwise, the battery pack loses its ability to fully recharge.

Using a damp cloth, clean the charging contacts on the handset about once a month.

If you are not going to use your phone for an extended period, disconnect the battery pack. This increases the battery pack’s usable life.

The supplied battery pack should last for about a year. If the battery pack does not hold a charge for more than two hours after an overnight charge, replace it with a new 3.6-volt,800 mAh battery pack with a connector that fits the socket in the battery compartment. You can order a replacement battery pack through RadioShack. Install the

new battery pack and charge it for about 15–20hours.o

12

SETTING MENU

OPTIONS

ABOUT THEMENUOPTIONS

There are five main menu setup options,

(DirectLink® Mode, Room Monitor, Handset Setup, Global Setupand System Reset)and 16 submenu options. Ô

SUMMARY OFMAINMENU

OPTIONS ANDSUBMENU

OPTION

DirectLink Mode

DirectLink Mode allows a pair of handsets to work without the base unit for direct handset-to-handsetcommunication, like a pair ofwalkie-talkie.Use them at sporting events or while shopping to stay in contact with family members or friends. You must set the two handsets to DirectLink Mode to utilize this feature.

Room Monitor

This feature allows you to monitor sounds in another room (see “Using Room Monitor” on page 17 for setup). One handset is placed in the desired room to monitor (acts as remote mic), and the other handset is placed near listener (remote speaker). This is useful for monitoring child activities.

Ô NOTEÔ

During Global Setup and System Reset, make sure your cordless phone is in standby mode (not in use), and all handsets are within range of the main base unit.

Setting Menu Options

13

Options Menu Setting

Handset Setup

The following submenu options must be set separately for each handset.

Submenu option

Description

 

 

Edit Voice Mail

Program or delete the voice mail access number (see

 

“Programming your Voice Mail Access Number” on

 

page 17).

 

 

Ringer Tones

Adjusting the ringer tone (see “Selecting a Ringer Tone”

(Default is Flicker)

on page 18).

 

Set the distinctive ring (tone your phone makes when

 

ringing) (see “Distinctive Ringer Setup” on page 18).

 

“Distinctive Ringer” allows you to preset memory

 

locations with a designated ring tone. When an incoming

 

call is received and the Caller ID information matches the

Distinct. Ring

information in one of the memory locations, the distinctive

ring that has been stored for that particular Caller will

(Default is on)

sound. If you have set multiple memory locations with

 

 

distinctive rings, switching the setting to “Distinctive Off”

 

will result in no distinctive ringing. All incoming calls will

 

have a normal ring tone. Switching to “Distinctive On” will

 

activate all programmed distinctive ring memory

 

locations.

 

 

 

Allows you to answer the phone without pressing

AutoTalk

TALK/FLASH orSPEAKER. When the AutoTalk is set to

On, simply remove the handset from the cradle and the

(Default is off)

phone automatically answers the call (see “Setting the

 

 

AutoTalk” on page 19).

 

Allows you to answer the phone without pressing

Anykey Answer

TALK/FLASH orSPEAKER. When the Anykey Answer is

On, you can answer a call by pressing any number key,

(Default is off)

/tone/< or#/> on the handset (see “Setting the Anykey

 

 

Answer” on page 19).

 

 

 

Customize your handset(s) by giving it a banner name.

 

The name will be displayed on the LCD screen during

Banner

standby mode, Intercom, Transfer, Room Monitor and

(True Banner)

Copy Phonebook operation. The banner name will be

 

displayed on the receiving handset as well (see “Setting

 

the True Banner” on page 19).

Language

The menu display options can be set to English, French

or Spanish for easy setup use (see “Selecting a

(Default is English)

Language” on page 19).

 

 

 

Key Touch Tone

Allows you to set your phone’s key touch-toneto On or

Off (tone your keypad makes when keys are pressed)

(Default is on)

(see “Setting the Key Touch Tone” on page 20).

 

 

 

14

Global Setup

If you change one of the Global settings, you change the setting for all additional handsets. Only one handset can change Global settings at a time.

Submenu option

Description

 

 

Day & time

Set the day and time of your display (see “Setting Day and

(Default is SUN

Time” on page 20).

12:00 AM)

 

 

 

 

Set the Caller ID on Call Waiting (CIDCW) setting. CIDCW

CIDCW

performs the same as regular Caller ID on a call waiting

number (see “Setting CIDCW (Caller ID on Call Waiting)” on

(Default is CW on/

page 20). Call Waiting Deluxe allows you to handle call

CWDX off)

waiting calls in seven different ways (see “Call Waiting Deluxe

 

 

Features” on page 40).

 

Store or edit the area code. If you enter a 3-digitarea code

 

number in the “Area Code” option, your local area code does

Area Code

not appear in the Caller ID message. For calls received from

outside your local area code, you will see a full 10-digitnumber

 

 

(see “Setting the Area Code” on page 21). Note: If your calling

 

area requires 10-digitdialing, do not program this option.

 

 

 

Set the dial mode to tone or pulse (see “Setting the Dial

Dial Mode

Mode” on page 21). Most phone systems use tone dialing,

which sends DTMF tone through phone line, the default

(Default is tone)

setting is tone dialing. Depends on your dialing system, set

 

 

the dial mode.

Copy Phonebook

Allow you to transfer the phonebook data stored in one handset

to another handset (see “Copy Phonebook” on page 21).

 

 

Voice Mail Tone

If your service does not support SDT message signal, set

your VMWI (Visual Message Waiting Inculcator) not to detect

(Default is on)

SDT message signal (see “Voice Mail Tone” on page 22).

 

 

 

System Reset

System Reset is used to clear the handset's ID from the main base unit, or the base ID from the handset.

Submenu option

Description

 

 

Clear the handset ID from the base. Use this option, for Deregister HS example, when you change the digital security code (see

“De-registerthe Handset” on page 22).

Clear the base ID. Use this option, for example, if you Replacing Base wish to deregister the base to use the handset with 43-

3570 (see “Replacing the Base Setting” on page 23).

Setting Menu Options

15

Options Menu Setting

SETTINGUP THEMENU

Entering the Menu

1.Press MENU/DEL in standby mode.

2.Use VOL/RING/ or VOL/RING/ to move the pointer to a desired main menu (DirectLink Mode, Room Monitor, Handset Setup, Global Setup, and System Reset).

3.Press SELECT/to select the desired main menu.

4.Use VOL/RING/ or VOL/RING/ to select a desired submenu and then press SELECT/ to enter.

In the submenu, use VOL/RING/ orVOL/RING/ to select an item. PressSELECT/to confirm your selection. For detailed instructions, see the following sections for the desired submenu.

5.To exit the menu, press END or place the handset to the cradle.

DirectLink Mode

Using the DirectLink Mode

1.Enter the DirectLink Mode menu (see “Entering the Menu”). To enter DirectLink mode press [SELECT] appears.

2.Press SELECT/to enter the DirectLink mode. You will hear a confirmation tone, andDirectLink Mode Complete appears.

3.To return back to the normal mode, exit the DirectLink mode. To exit the DirectLink mode, press MENU/DEL, and thenSELECT/, or return the handset to the cradle.

16

Room Monitor

Using Room Monitor

1.Enter the Room Monitor menu (see “Entering the Menu” on page 16).

To Room Monitor appears.

2.Select the handset you want to monitor by using VOL/RING/ or VOL/RING/ . When monitoring, be sure the other handset is facing up so the microphone can pick up the sound clearly.

3.Press SELECT/.

RoomMonitor appears and you hear sounds in the room where the handset is installed.

Handset speaker is on the rear side. Place the handset so the speaker is not covered.

4.To finish the Room Monitor, press END or return the handset to the cradle.

Handset Setup

Programming your Voice Mail Access Number

1.Enter the Handset Setup menu, and then the Edit Voice Mail submenu (see “Entering the Menu” on page 16). Edit V_mail No. appears.

2.Enter your personal access number using the number keypad (0-9), /

TONE/<, #/>, MENU/DEL, or REDIAL/ PAUSE(up to 20 digits).

3.Press SELECT/. You will hear a confirmation tone.

To delete the current Voice Mail Access Number, delete all numbers in step 2 using

MENU/DEL and SELECT/ .

Setting Menu Options

17

Options Menu Setting

Selecting a Ringer Tone

1.Enter the Handset Setup menu, and then the Ringer Tones submenu (see “Entering the Menu” on page 16).

There are ten ringer tones or ten melodies to choose from.

Ringers [Flicker, Clatter, Soft Alert, Wake Up, Light Bug, Beep Boop, Tone Board, Chip Chop, Party Clap, Reminder]

Melodies [Beethoven’s Symphony #9 (Beethoven9), For Elise (Elise), We Wish You A Merry Christmas (MerryXmas), Home Sweet Home (Hm Swt Hm), Lorri Song #6 (Lorri Song), When Irish Eyes Are Smiling (Irish Eyes), Aura Lee, Let Me Call You Sweet Heart (Sweetheart), Star Spangled Banner (Star Spngl), Old MacDonald (Old MacDld)]

2.Press VOL/RING/ or VOL/RING/ to move the pointer. You will hear the ringer or melody as you scroll through the options.

3.Press SELECT/. You will hear a confirmation tone.

Distinctive Ringer Setup

1.Enter the Handset Setup menu, and then the Distinct. Ring submenu (see “Entering the Menu” on page 16).

2.Press VOL/RING/ or VOL/RING/ to select On or Off.

3.Press SELECT/. You will hear a confirmation tone.

18

Setting the AutoTalk

1.Enter the Handset Setup menu, and then the Auto Talk submenu (see “Entering the Menu” on page 16).

2.Press VOL/RING/ or VOL/RING/ to select On or Off.

3.Press SELECT/. You will hear a confirmation tone.

Setting the Anykey Answer

1.Enter the Handset Setup menu, and then the Anykey Answer submenu (see “Entering the Menu” on page 16).

2.Press VOL/RING/ or VOL/RING/ to select On or Off.

3.Press SELECT/. You will hear a confirmation tone.

Setting the True Banner

1.Enter the Handset Setup menu, and then the Banner submenu (see “Entering the Menu” on page 16).

2.Use the number keypad (0-9), /tone/< #/>, or MENU/DELto enter or edit the name.

3.Press SELECT/. You will hear a confirmation tone.

Selecting a Language

1.Enter the Handset Setup menu, and then the Language submenu (see “Entering the Menu” on page 16).

2.Press VOL/RING/ or VOL/RING/ to choose English, Français

(French), or Español (Spanish).

3.Press SELECT/. You will hear a confirmation tone.

Setting Menu Options

19

Options Menu Setting

Ô NOTEÔ

For setting the day and time, the idle time-outis extended to two minutes.

Setting the Key Touch Tone

1.Enter the Handset Setup menu, and then the Key Touch Tone submenu (see “Entering the Menu” on page 16).

2.Press VOL/RING/ or VOL/RING/ to select On or Off.

3.Press SELECT/. You will hear a confirmation tone.

Global Setup

When a Global setting is changed from one handset, this affects all registered handsets. Ô

Setting Day and Time

1.Enter the Global Setup menu, and then the Day & Time submenu (see “Entering the Menu” on page 16).

2.Press VOL/RING/ or VOL/RING/ to select the day of the week, and then press SELECT/ .

3.Press VOL/RING/ or VOL/RING/ to set hour, and then press SELECT/ .

4.Press VOL/RING/ or VOL/RING/ to set minute and then press SELECT/ .

5.Press VOL/RING/ or VOL/RING/ to choose AM or PM and then press SELECT/ . You will hear a confirmation tone.

Setting CIDCW (Caller ID on Call Waiting)

1.Enter the Global Setup menu, and then the CIDCW submenu (see “Entering the Menu” on page 16).

2.Press VOL/RING/ or VOL/RING/ to select CW On/CWDX On,

CW On/CWDX Off, orCW Off/CWDX Off and then pressSELECT/. You will hear a confirmation tone.

20