Radio Shack 3-DVD Changer User Manual

Size:
288.23 Kb
Download

Complete 7-Piece600-WattHome

Theater Audio System

with 3-DVDChanger

Manual

before using this equipment.

Owner’s

Please read

ˆ Read this First

This audio system is made and tested to meet exacting safety standards. It meets both UL and FCC requirements.

WARNING: To reduce the risk of fire or shock hazard, do not expose this product to rain or moisture.

 

CAUTION

!

 

RISK OF ELECTRIC SHOCK. DO NOT

 

OPEN.

 

 

 

 

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER OR BACK. NOUSER-SERVICEABLEPARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.

!

Warnings:

This symbol is intended to alert you to the presence of uninsulated dangerous voltage within the product’s enclosure that might be of sufficient magnitude to constitute a risk of electric shock. Do not open the product’s case.

This symbol is intended to inform you that important operating and maintenance instructions are included in the literature accompanying this product.

This system employs a laser light beam. Only a qualified service person should remove the cover or attempt to service this device, due to possible eye injury.

The use of controls, adjustments, or procedures other than those specified herein might result in hazardous radiation exposure.

THE FCC WANTS YOU TO KNOW

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult your local RadioShack store or an experienced radio/TV technician for help.

If you cannot eliminate the interference, the FCC requires that you stop using your system.

Changes or modifications not expressly approved by RadioShack may cause interference and void the user’s authority to operate the equipment.

REGION MANAGEMENT INFORMATION

Region Management Information: This DVD Player is designed and manufactured to respond to the Region Management Information that is recorded on a DVD disc. If the Region number described on the DVD disc does not correspond to the Region number of this DVD player, this DVD player cannot play that disc.

The Region number of this DVD player is 1 (USA/CANADA).

Notes on Unauthorized Discs

You may not be able to play back some DVD video discs on this player if they were purchased from outside your geographic area or made for business purposes. When you try to play back an unauthorized disc, “Check Regional Code” appears on the TV screen.

NOTES ON COPYRIGHT

It is forbidden by law to copy, broadcast, show, broadcast on cable, play in public, and rent copyrighted material without permission.

DVD video discs are copy protected, and any recordings made from these discs will be distorted.

This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only, unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

PLACING THE RECEIVER

Do not place objects directly on top of the receiver as it could prevent proper heat dispersal.

When installing in a rack or shelf, be sure to leave more than 8 inches of space above and behind the receiver.

© 2001 RadioShack Corporation.

All Rights Reserved.

RadioShack is a trademark used by RadioShack Corporation. © 1996 Digital Theater System, Inc.

DTS and DTS Digital Surround are trademarks of Digital Theater System, Inc. All Rights Reserved.

© 1992-1997Dolby Laboratories, Inc.

Dolby, ProLogic, and the double-Dsymbol are trademarks of Dolby Laboratories, Inc. All Rights Reserved.

Spatializer(R) 3-DStereo, SpatializerN-2-2(TM) and thecircle-in-squaredevice are trademarks owned by Desper Products, Inc,. All Rights Reserved.

2

Read this First

MAKING CABLE CONNECTIONS

Be careful not to bend cables over the top of the receiver.

If cables are placed on top of the receiver, the magnetic field prodcued by the receiver’s transformers can cause the speakers to produce a humming noise.

USING DISCS

When using discs, you must always take the following precautions:

Do not touch the playback side of the disc.

Do not attach paper or tape to discs.

Do not store discs in a place subject to direct sunlight or near heat sources.

Do not store discs in places subject to moisture and dust such as a bathroom or near a humidifier.

Store discs vertically in a case. Stacking or placing objects on discs outside of their case may cause warping.

Cleaning Discs

Fingerprints and dust on the disc cause picture and sound deterioration. Wipe the disc from the center outward with a soft cloth. Always keep the disc clean.

If you cannot wipe off the dust with a soft cloth, wipe the disc lightly with a slightly moistened soft cloth and finish with a dry cloth.

Do not use any type of solvents such as thinner, benzene, commercially available cleaners or anti-staticspray for vinyl LPs. They might damage the disc.

IMPORTANT SAFETY INSTRUCTIONS

Careful attention is devoted to quality standards in the manufacture of your system, and safety is a major factor in its design. However, safety is also your responsibility.

This section lists important information that will help you properly use and enjoy your system. Read all the included safety and operating instructions before using your system. Follow them closely, and retain them for future reference.

1.Heed Warnings — Follow all warnings on the product and in the operating instructions.

2.Cleaning — Unplug this product from the wall outlet before cleaning. Use only a damp cloth for cleaning. Do not use liquid or aerosol cleaners.

3.Attachments — Do not use attachments/accessories not recommended by the product manufacturer, as they might create a hazard.

4.Water and Moisture — Do not use this product near water (for example, near a bathtub, washbowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool).

5.Accessories — Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recom-

mended by the manufacturer or sold with the product. Follow the manufacturer's instructions for mounting, and use a recommended mounting accessory.

Carts — Move the product on a cart carefully. Quick stops, excessive force, and uneven surfaces may cause the product/ cart to overturn.

6.Disc Tray — Keep your fingers well clear of the disc tray as it is closing. It may cause serious personal injury.

7.Burden — Do not place a heavy object on or step on the product. The object may fall, causing serious personal injury and serious damage to the product.

8.Connecting — When you connect the product to other equipment, turn off the power and unplug all the equipment from the wall outlet. Failure to do so may cause an electric shock and serious personal injury. Read the owner’s manual of the other equipment carefully and follow the instructions when making any connections.

9.Sound Volume — Reduce the volume to the minimum level before you turn on the product. Otherwise, sudden high volume sound may cause hearing or speaker damage.

10.Sound Distortion — Do not allow the product to output distorted sound for a longtime. It may cause speaker overheating and fire.

11.Headphones — When you use the headphones, keep the volume at a moderate level. If you use the headphones continuously with high volume sound, it may cause hearing damage.

12.Laser Beam — Do not look into the opening of the disc tray or ventilation opening of the product to see the source of the laser beam. It may cause sight damage.

13.Disc — Do not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause serious personal injury and product malfunction.

14.Ventilation — Slots and openings in the cabinet provide ventilation, ensure reliable operation, and protect from overheating. Do not block or cover these openings, and do not place the product on a bed, sofa, rug, or other similar surface. Do not place the product in a built-ininstallation such as a bookcase or rack unless it provides proper ventilation as specified by the manufacturer.

15.Power Sources — Operate this product using only the power source indicated on its marking label. If you are not sure of your home's power type, consult your product dealer or local power company.

16.Polarization — This product is equipped with a polarized AC line plug (a plug having one blade wider than the other). This plug will fit in the power outlet only one way. This is a safety feature. If you cannot insert the plug fully into the outlet, try reversing the plug. If the plug still doesn't fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. If you need an extension, use a polarized cord.

17.Power-CordProtection — Routepower-supplycords so they are not likely to be walked on or pinched by items placed on or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

Read this First

3

18.Lightning — For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-linesurges.

19.Overloading — Do not overload wall outlets, extension cords, or integral convenience receptacles, as this can result in a risk of fire or electric shock.

20.Objects and Liquids — Never push objects of any kind into this product through openings, as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

21.Servicing — Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

22.Damage Requiring Service — Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

When the power-supplycord or plug is damaged.

If liquid has been spilled or objects have fallen into the product.

If the product has been exposed to rain or water.

If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation.

If the product has been dropped or damaged in any way.

When the product exhibits a distinct change in performance.

23.Replacement Parts — When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer or having the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

24.Safety Check — Upon completion of service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

25.Wall or Ceiling Mount — The product should be mounted to a wall or ceiling only as recommended by the manufacturer.

26.Heat — The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

27.Non-usePeriods — Unplug the system’s power cord when you will not use it for extended periods.

28.Outdoor Antenna Grounding — If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-upstatic charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of thelead-inwire to an antenna discharge

unit, size of grounding conductors, location of antenna-dischargeunit, connection to grounding electrodes, and requirements for the grounding electrode.

Note to CATV System Installer

This reminder is provided to call the CATV system installer’s attention to Section 820-40of the NEC which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

Power Lines — An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

4

Read this First

ˆ Contents

 

Features ..........................................................................................

6

Preparation .....................................................................................

7

Connecting Components .............................................................

7

Connecting a TV .....................................................................

7

Connecting a Cassette Deck ..................................................

7

Connecting a VCR ..................................................................

7

Connecting a Satellite Receiver or Cable Box ........................

7

Connecting a Digital Optical Audio Devices ............................

7

Connecting an Auxiliary Audio Device ....................................

7

Connecting a Second Sub Woofer ..........................................

7

Connecting Antennas ..................................................................

7

FM Indoor Antenna .................................................................

7

FM Outdoor Antenna ..............................................................

7

AM Indoor Loop Antenna ........................................................

7

AM Outdoor Antenna ..............................................................

8

Connecting the Speakers ............................................................

8

Placing the Speakers ..................................................................

8

Installing Batteries in the Remote Control ...................................

8

Receiver Operation ........................................................................

9

A Quick Look at the Receiver’s Controls .....................................

9

Using the Tuner .........................................................................

10

Listening To FM Stereo Broadcasts ......................................

10

Presetting Radio Stations .....................................................

10

Manual Preset .......................................................................

10

Auto Preset ...........................................................................

10

Listening to Preset Stations ..................................................

10

Switching Between Preset Stations and Manual Tuning .......

10

Using the CD Player ..................................................................

10

Continuous Play ....................................................................

11

Changing the Sound Mode ...................................................

11

Using Night Mode ......................................................................

11

Using the Sleep TImer ...............................................................

11

Using the Dimmer ......................................................................

11

Remote Control Operation ..........................................................

12

A Quick Look at the Remote Control .........................................

12

Operating Range of the Remote Control ...................................

12

Setting up the Surround Sound System ....................................

13

Changing the Speaker Size ..................................................

13

Changing the Channel Level .................................................

13

Changing the Speaker Distance ...........................................

13

Surround Effects ...................................................................

14

Changing System Settings - Special Circumstances ............

14

Using the Remote Control Unit to Control Additional

 

Components ..............................................................................

14

Controlling the Tuner .................................................................

14

Listening To FM Stereo Broadcasts ......................................

14

Presetting Radio Stations .....................................................

14

Manual Preset .......................................................................

14

Auto Preset ...........................................................................

15

Listening to Preset Stations ..................................................

15

Switching Between Preset Stations and Manual Tuning .......

15

Controlling the CD Player ..........................................................

15

Changing the Sound Mode ...................................................

15

Using GUI Menu Icons ..........................................................

15

Repeat Play ..........................................................................

15

Programming Tracks .............................................................

16

Modifying the Program and Adding a Track ..........................

16

Random Play ........................................................................

16

Controlling the Sleep TImer .......................................................

16

DVD Player Operation .................................................................

17

Basic Playback ..........................................................................

17

Stopping Play ........................................................................

17

Pausing Play .........................................................................

17

Advancing by Frames ...........................................................

17

Playing in Slow-Motion ..........................................................

17

Skipping Chapters .................................................................

18

Scanning ...............................................................................

18

Advanced Features ...................................................................

18

Using GUI Menu Icons ..........................................................

18

Using a Title Menu ................................................................

18

Using a DVD Menu ...............................................................

18

Changing Subtitle Language .................................................

19

Changing Soundtrack Language ..........................................

19

Viewing from Another Angle .................................................

19

Using Repeat Play ................................................................

19

Zooming In ............................................................................

19

Setting rating level and password .............................................

19

Selecting a Rating Level .......................................................

19

Setting a Password ...............................................................

20

Clearing Your Password ........................................................

20

Selecting TV Aspect ..................................................................

20

Selecting Digital Audio Out ........................................................

20

Troubleshooting ..........................................................................

21

Care ...........................................................................................

22

Manuracturer’s Codes .................................................................

23

TV Codes ..............................................................................

23

VCR Codes ...........................................................................

24

Cable Codes .........................................................................

25

SAT Codes ............................................................................

26

Specifications ..............................................................................

27

Amplifier Section ...................................................................

27

Tuner Section ........................................................................

27

Video Section ........................................................................

27

Speaker Section ....................................................................

28

Miscellaneous .......................................................................

28

Contents

5

ˆ Features

Your Complete 7-Piece600-WattHome Theater Audio System is a great system that incorporates some of the best features in home theater technology. The Home Theater Audio System comes complete with a shieldedcenter-channelspeaker, a bandpass-typesubwoofer, two shieldedfront-channelspeakers, two rear surround speakers, a remote control, and a receiver equipped with a tuner and a3-discDVD player.

Its other features include:

Dolby Digital, Dolby ProLogic, and DTS Sound Settings — let you use the Home Theater Audio System for a movie-theater surround sound experience

Adjustable Speaker Size, Channel Level, and Distance — lets you customize your setup for a true surround sound experience

Additional Component Connections — let you connect other audio and audio/visual components to the receiver so that you can use the system’s surround sound speakers

Night Mode — lets you compress the dynamic range, reducing the difference in loudness between different sounds

Parental Lock (Rating Level) — lets you set a ratings level so that your children cannot watch a DVD that has a rating higher than you set

Sleep Timer — lets you program the receiver to turn off after a set time period

6

Features

ˆ Preparation

CONNECTING COMPONENTS

You must connect a TV to the receiver in order to use the receiver’s DVD player. You can connect other audio and audio/visual components to the receiver in order to use the Home Theater Audio System’s surround sound capabilities.

Connecting a TV

Use audio/video cords (not supplied) to connect a TV to the receiver. Connect red plugs to the red AUDIO jacks and white plugs to the whiteAUDIO jacks.

If your TV has an S-Videojack, use anS-Videocable to connect your TV to the receiver’sS-VIDEO OUT. If your TV does not have anS-Vid-eo jack, use audio/video cord to connect your TV to the receiver’s

MONITOR OUT.

Connecting a Cassette Deck

Use audio/video cords (not supplied) to connect a cassette deck to the receiver. Connect red plugs to the red AUDIO jacks and white plugs to the whiteAUDIO jacks. Make sure you connect the VCR to both theTAPE IN andTAPE OUT sets of jacks.

Note: If the cassette deck is placed too close to the receiver, noise might occur during cassette playback. If this happens, move the cassette deck farther away from the receiver.

Connecting a VCR

Use audio/video cords (not supplied) to connect a VCR to the receiver. Connect red plugs to the red AUDIO jacks and white plugs to the whiteAUDIO jacks.

Connect yellow plugs to the yellow VIDEO jacks.

Note: Make sure you connect the VCR to both theIN andOUT sets of jacks.

Connecting a Satellite Receiver or Cable Box

Use audio/video cords (not supplied) to connect a satellite receiver or cable box to the receiver. Connect red plugs to the red AUDIO jacks and white plugs to the whiteAUDIO jacks.

Note: Your cable box or satellite receiver must use audio/video cords or Toslink optical cable to connect to the receiver. If your equipment only uses coaxial cable, you cannot connect it to the receiver.

If your satellite receiver or cable box has digital output, use an optical cable to connect the satellite receiver to the home theater receiver’s SAT IN optical jack. If your satellite receiver or cable box does not have digital output, use analog cable to connect it to the home theater receiver’sSAT IN video jack.

You can also connect a satellite receiver, MD or DAT recorder, CD player, or anything else with digital output to the receiver’s SAT IN optical jack. Use Toslink optical cable to connect the desired device to the receiver.

Connecting an Auxiliary Audio Device

You can also connect an audio device that does not require Toslink (such as an MP3 player, playback cassette deck, or portable CD player) to the Home Theater Audio System. Use audio cords to connect the desired device to the receiver’s AUX jacks. Connect red plugs to the redAUDIO jacks and white plugs to the whiteAUDIO jacks.

Connecting a Second Sub Woofer

You can connect a second or larger powered subwoofer to the system. Connect the sub woofer to the receiver’s SUB WOOFER PRE-OUT jack using shielded audio cable (not supplied).

CONNECTING ANTENNAS

When connecting equipment, always make sure the power is switched off and the power cord is disconnected from the wall outlet.

FM Indoor Antenna

In an area with strong FM signals, the T-typeFM antenna (supplied) is sufficient.

1.Use a flat or Phillips screwdriver to loosen the screws on the supplied transformer.

2.Place the metal connectors on the end of theT-typeantenna’s base on the transformer’s metal contacts (underneath the screw heads) then tighten the screws.

3.Plug the transformer into ANTENNA FM 75 Ω.

4.Extend the T-antenna’sother two wires and attach them to a wall or window frame for the best possible reception.

If you have a cable FM antenna, use a coaxial cable to connect it to

ANTENNA FM 75 Ω.

FM Outdoor Antenna

In an area where FM signals are weak, you must use a 75-ohmun-balanced-typeoutdoor FM antenna (not supplied). Generally, a3-ele-ment antenna will be sufficient. If you live in an area where the FM signals are particularly weak, it may be necessary to use one with 5 or more elements.

Connect the antenna’s coaxial cable to the supplied transformer. Plug the transformer into ANTENNA FM 75 Ω.

Connecting a Digital Optical Audio Devices

You can connect a digital audio device such as an DAT (Digital AudioTape) or MD (Mini Disc) recorder to the receiver’s DIGITAL OUT to record audio from the receiver. Use Toslink optical cable to connect the DAT or MD recorder to the receiver’sDIGITAL OUT optical jack.

AM Indoor Loop Antenna

The supplied high-performanceAM loop antenna is sufficient for good reception in most areas.

Preparation

7

Connect the loop antenna’s wires to AM andGND. Place the antenna in a location (for example, on a shelf or window frame) that gives the best reception.

Keep the antenna as far away as possible from the entire system, speaker cords and the power cord to prevent unwanted noise.

AM Outdoor Antenna

If the supplied AM loop antenna does not deliver sufficient reception, use an outdoor AM antenna (not supplied).

Note: Even when using an outdoor AM antenna, do not disconnect the AM indoor loop antenna.

Use an insulated wire more than 15 ft (5 m) long. Strip one end, and connect that end to AM.

The antenna wire should be strung outdoors or indoors near a window. For better reception, connect the GND terminal to a reliable ground.

CONNECTING THE SPEAKERS

When connecting equipment, always make sure the power is switched off and the power cord is disconnected from the wall outlet.

Note: Use speakers with a normal impedance of 6 Ohms.

Follow these steps to connect the speakers.

1.Remove the plastic end pieces from the wires.

2.Twist the exposed ends of the bare wire strands.

3.Press up (or down) the speaker’s terminal and insert the appropriate wire ends. The color of the speaker wire’s plastic coating is the same as the color of the matching terminal.

Note: Be sure to connect each speaker to the appropriate speaker terminal, connecting positive to positive (+ to +) and negative to negative (– to–).

4.Connect the front speaker’s wire to the receiver’s SPEAKERS FRONT L andR terminals (Red/Black).

Connect the rear speaker’s wire to the receiver’s SPEAKERS REAR L andR terminals (Gray/Black).

Connect the center speaker’s wire to the receiver’s SPEAKERS CENTER terminal (Blue/Black).

Connect the subwoofer’s wire to the receiver’s SPEAKERS WOOFER terminal (Brown/Black).

5.Release the speaker terminal.

6.Plug the AC power cord into an AC wall socket.

PLACING THE SPEAKERS

1.Place the front left and right speakers at equal distances from the TV.

2.Install the center speaker above or below the TV so that the sound of the center channel is localized at the TV screen.

Caution: If you choose to install the center speaker on top of the TV, be sure to secure it, to reduce the risk of damage or injury

resulting from the speaker falling from the TV in the event of external shocks (for example, earthquakes).

3. If possible, install the surround speakers slightly above ear level.

Note: Try not to install the surround speakers farther away from the listening position than the front and center speakers. Doing so can weaken the surround effect.

To achieve the best possible surround sound, install your speakers as shown below. Be sure all speakers are installed securely to prevent accidents and improve sound quality.

Overhead view of speaker set up

(Illus of speaker set up, please use the illus of 31-5011if necessary)

INSTALLING BATTERIES IN THE REMOTE CONTROL

Your remote control requires two AAA batteries (not supplied) for power. For the best performance and longest life, we recommend RadioShack alkaline batteries.

Cautions:

Use only fresh batteries of the required size and recommended type.

Do not mix old and new batteries or different types of batteries. Follow these steps to install batteries.

1.Slide the battery compartment cover in the direction of the arrow to remove it.

2.Place the batteries in the compartment as indicated by the polarity symbols (+ and –)marked inside.

3.Replace the cover.

When the remote control stops operating properly, replace the batteries.

Warning: Dispose of old batteries promptly and properly. Do not burn or bury them.

Caution: If you do not plan to use the remote control for a month or longer, remove the batteries. Batteries can leak chemicals that can destroy electronic parts.

8

Preparation

ˆ Receiver Operation

A QUICK LOOK AT THE RECEIVER’S CONTROLS

DISC SKIP/TUNING MODE – Press to skip discs in DVD/CD mode.

In tuner mode, press to switch between presets and manual tuning (see “Switching Between Preset Stations and Manual Tuning” on Page 10).

FUNCTION – Rotate to select the desired audio or audio/video source. The selected source name appears on the display panel.

BAND/PLAY – Press to select AM or FM band in tuner mode.

Press to plays back the disc in DVD/CD mode.

DISC 1, 2, 3 – Press to open or close the disc trays.

Note: You cannot use these buttons in tuner mode.

TUNING/PRESET – Repeatedly press to tune to AM or FM stations and select preset stations in tuner mode.

NIGHT MODE – When the sound source is Dolby Digital or stereo mode, press to compress large dynamic range (see XXXX on page XX)..

PHONES – This jack is compatible with wide range of conventional dynamic headphone types.

When you connect headphones, the unit automatically selects stereo mode.

SLEEP – Repeatedly press to set the sleep timer.

Display Panel

MEMORY/ PAUSE – stores a station in memory in tuner mode; pauses the disc in DVD/CD mode.

FM MODE/STOP – In tuner mode, press to select stereo or monaural mode for FM in tuner mode.

In DVD/CD mode, press to stop the disc.

DIMMER – Press once to dim the display panel. Press one more to return to normal status.

DTS – Press to switch to 5.1 Channel DTS from stereo mode.

SURROUND MODE

Press to switch surround modes between PRO LOGIC, THEATER, HALL, and STADIUM for analog equipment (not for SATOPT function).

DOLBY DIGITAL – Press to switch to 5.1 Channel Dolby Digital from stereo mode.

STEREO – Press to switch from surround mode to stereo mode.

In Dolby Digital mode, press to change the mode to stereo. IJ appears.

Receiver Operation

9

TUNING MODE
TUNING/PRE-
TUNING MODE,
FM MODE

USING THE TUNER

1.Press POWER. The receiver defaults to the last selected function.

2.Rotate FUNCTION to the tuner function.

3.Press BAND to select the desired band.

4.Repeatedly press TUNING/PRESET #or,ý- to tune in the desired station. When you reach a station,Jkd[Z appears above the station number.

To change the frequency by one step, press TUNING/PRESET )

#or,- quickly (less than half a second).

To tune to the next clear frequency, hold down TUNING/PRESET

)ý# or ,-,then release the button. The system automatically tunes to the next strong station.

Listening To FM Stereo Broadcasts

In FM mode, press to select stereo or mono. When you select the stereo mode, IJ appears to the right ofJkd[Z. It goes off when you select mono.

When you listen to very weak FM stereo stations, you might hear higher-than-normalbackground hiss. Switch to mono to eliminate the hiss.

Presetting Radio Stations

You can preset 30 AM and 30 FM stations regardless of the reception. Tune in the desired stations using auto or manual tuning.

Manual Preset

1.Press BAND to select the desired band.

2.Repeatedly press TUNING/PRESET )ý#or,- to tune in the desired station.

To change the frequency by one step, press TUNING/PRESET )

#or,- quickly (less than half a second).

To tune to the next clear frequency, hold down

SET )ý# or ,-,then release the button. The system automatically tunes to the next strong station.

3.Press MEMORY.C;CE flashes for 5 seconds. WhenC;CE goes off, press the button again (C;CE flashes again).

4.Select the preset number with TUNING/PRESET )ý#or,-.

5.Press MEMORY again.

6.Repeat Steps 1–5to memorize other stations (up to 30 stations for each band). If you store a new station on a memory number in which a station is stored, the old station is cleared.

To store stations on the other band, repeat Steps 1–6,substituting the other band in Step 1.

Note: If you want to store more stations later, you might find that pressingTUNING/PRESET )ý#or,-onlymoves the tuner to the next preset station (instead of moving the frequency one step). If this happens, press to return to manual tuning (see “Switching Between Preset Stations and Manual Tuning”).

Auto Preset

1.Press BAND to select the desired band.

2.Hold down MEMORY for about 3 seconds.

3.The tuner automatically begins scanning, and stores the first 30 strong signals it receives.

4.Scanning stops automatically after radio stations have been stored in the auto preset memory.

Note: PressMEMO again to stop auto scanning earlier.

To store stations on the other band, repeat Steps 1–4,substituting the other band in Step 1.

Listening to Preset Stations

To listen to a radio station stored in the station memory, press TUNING MODEthen TUNING/PRESET)ý#or ,-.

Switching Between Preset Stations and Manual

Tuning

If you store preset stations, pressing TUNING/PRESET )ý#or,- scrolls through the preset stations, rather than changing the frequency station by station.

To switch to scrolling by individual stations, press

then repeatedly press TUNING/PRESET )ý# or,- quickly to change the frequency by one step. Or hold downTUNING/PRESET )

#or,- to tune to the next clear station.

To switch back to scrolling through the preset stations, press TUNING MODE, then repeatedly press TUNING/PRESET )ý# or ,- until you reach the desired station.

USING THE CD PLAYER

You can use the receiver’s 3-DVDchanger to listen to audio CDs.

Important: You can only use audio CDs and someCD-Rswith the reciever.CD-ROM,CD-G,photo CD, andCD-idiscs can not be played on this player.

1.Press POWER.

2.Rotate FUNCTION until:L:%9: appears.

3.Press DISC 1,DISC 2, orDISC 3 to open the desired drawer.

4.Place the desired CDs in the tray, then press the appropriate DISC button again to close the drawer.

Note: If you want to load more than one CD, you can press another DISC button. The receiver closes the open drawer and opens the drawer of the DISC button you pressed.

5.To select a CD, repeatedly press DISC SKIP until the desired CD’s number blinks.

6.Press PLAY. The disc icon (at the far left) begins to rotate.

To pause playback, pressPAUSE. The disc icon flashes rapidly. To resume playback, pressPAUSE again or pressPLAY.

10

Receiver Operation

To move forward through a track, hold down TUNING/PRESET

,- for about 2 seconds. Repeat up to two times to increase thefast-forwardspeed. To resume playback, pressPLAY.

Note: At the beginning or end of a track on an audio CD, the scan speed returns to normal.

To move backward through a track, hold down TUNING/PRESET

)ý# for about 2 seconds. Repeat up to two times to increase the rewind speed. To resume playback, pressPLAY.

To skip to the next track on the CD, press TUNING/PRESET ,- once.

To return to the beginning of the current track, press TUNING/ PRESET)ý#.

To return to the previous track, press TUNING/PRESET )ý# twice.

To stop playback, pressSTOP. The disc icon stops rotating, andH;IKC; appears. To resume playback, pressPLAY. To stop playback completely, pressSTOP again.

Continuous Play

When the receiver finishes playing an audio CD, it automatically plays the disc on the next tray.

Changing the Sound Mode

You can listen to your CDs using Stereo or Surround modes.

For stereo only, press STEREO once.

For a surround mode, repeatedly pressSURROUND MODE until the desired mode (J>;7J;H,>7BB,IJ7:?KC, orFHEýBE=?9) appears.

Note: Dolby Digital and DTS modes do not work with CDs.

USING NIGHT MODE

You can use Night Mode to compress large dynamic ranges, resulting in “quieter” explosions and other loud sounds in movies. The Night Mode feature adjusts the dynamic range so that there is less disparity in the noise level of all sounds in a movie (explosions, music, dialogue, and so on).

While in Dolby Digital or Stereo mode, press NIGHT MODE to turn Night Mode on. PressNIGHT MODE again to turn it off.

Note: Night Mode is not available for movies using DTS mode.

USING THE SLEEP TIMER

You can set the sleep timer to turn off the receiver after a set period of time.

Repeatedly press SLEEP to set the sleep timer to the desired time ('&,(&,)&,*&,+&,,&,-&,.&,or/& minutes). The receiver turns off when the selected time has expired.

USING THE DIMMER

Press DIMMER to make the display dimmer. Press again to return the display to its original brightness.

Receiver Operation

11

ˆ Remote Control Operation

A QUICK LOOK AT THE REMOTE CONTROL

MUTE – Press to immediately decrease the sound level.CKJ; appears on the display panel. To restore the

sound, press again.

PRESET – / + –-During AM or FM reception, you can scan through other frequencies or select the preset numbers.

BAND – selects AM or FM band while listening to the tuner function.

FM MODE (FM MONO/STEREO) – selects FM mono or stereo mode.

SURROUND – When you select an analog source (TUNER,AUX,TAPE,TV,VCR, or

SAT), as you pressSURROUND, the surround mode changes.

TEST TONE – Turns on or off the test tone function in DTS, DOLBY DIGITAL, or PRO LOGIC mode. The test tone is output from Front L speaker, Center speaker, Front R speaker, Surround R speaker, Surround L speaker, (Subwoofer speaker: when Subwoofer on).

TONE – Lets you adjust the low frequency level (BASS) with (left arrow icon) or (right arrow icon) and also you can adjust high frequency level (TREBLE) with (left arrow icon) or (right arrow icon) according to your taste and room acoustics.

SLEEP – Press to set the sleep time. The sleep time changes to'&,(&,)&, .../& (minutes), andE<< (former display).

TUNING MODE – selects and deselects preset mode.

MEMORY – Press to memorize the desired station frequency.

OPERATING RANGE OF THE REMOTE CONTROL

The remote control may not work properly if:

There are obstacles between the remote control and the receiver’s remote sensor.

Direct sunlight or fluorescent light is shining onto the remote sensor.

The receiver is located near a device that is emitting infrared rays.

The receiver is operated simultaneously with another infrared remote control.

12

Remote Control Operation

SETTING UP THE SURROUND SOUND SYSTEM

You can use your Home Theater Audio System as soon as you take it out of the packaging. If you wish to fine-tunethe system (for example, substitute different speakers or alter the sound distribution), follow the directions below.

Changing the Speaker Size

Note: If you are using the speakers provided in your Home Theater Audio System, the speaker size defaults are correct. If you are using other speakers, follow these steps.

1.Press POWER.

2.Press SETUP.IFýI?P; appears.

3.Press 7.<HEDJ appears.

4.Press 7 again.<#IC7BB appears. To change to<#B7H=;, press

8or9.

Note: If the cone size (diameter) of the speaker is larger than 5 inches, change to<#B7H=;.

5.Press ENTER.9;DJ;H appears.

6.Press 7.9#IC7BB appears. To change to9#B7H=;, press8 or9. To change to9#DED;, press8or9again.

Note: If the cone size (diameter) of the speaker is larger than 5 inches, set the item to9#B7H=;.

7.Press ENTER.IKHH appears.

8.Press 7.I#IC7BB appears. To change toI#ýB7H=;, press8 or9. To change toI#DED;, press8or9again.

Note: If the cone size (diameter) of the speaker is larger than 5 inches, set the item toI#B7H=;.

9.Press ENTER.IK8#M< appears.

10.Press 7.IM#O;I appears. If you aren’t using a subwoofer, change toIM#DE by pressing8or9.

11.Press ENTER.<HEDJ appears. PressSETUP again to exit.

Changing the Channel Level

The default channel level settings are 0 dB for each speaker. You can change the speakers’ sound distribution to suit your surround sound needs. For example, if you are closer to the left front speaker than the right front speaker, the left front speaker might seem “louder” than the right one. To adjust it, you must change the channel level for one or both speakers until the sound evens out.

Follow these steps to change the channel level.

1.Press SETUP, then8.9>ýB;L;B appears.

2.Press 7.<BýB;L;Býappears.

3.Press 7 again.<ý &Z8 appears. To change the front left speaker’s level, repeatedly press8 or9 until you reach the desired level (¶'& to!'&ýZ8).

4.Press ENTER.9ýB;L;B appears.

5.Press 7.9ý&Z8ýappears. To change the center speaker’s level, repeatedly press8 or9 until you reach the desired level (¶'& to!'&ýZ8).

6.Press ENTER.<HýB;L;B appears.

7.Press 7.<Hý&Z8ýappears. To change the front right speaker’s level, repeatedly press8or9until you reach the desired level (¶'& to!'&ýZ8).

8.Press ENTER.IHýB;L;B appears.

9.Press 7.IHý&Z8ý appears. To change the rear right speaker’s level, repeatedly press8or9until you reach the desired level (¶'& to!'&ýZ8).

10.Press ENTER.IBýB;L;B appears.

11.Press 7.IBý &Z8ý appears. To change the rear left speaker’s level, repeatedly press8or9until you reach the desired level (¶'& to!'&ýZ8).

12.Press ENTER.IMýB;L;B appears.

13.Press 7.IMý&Z8ýappears. To change the sub woofer’s level, repeatedly press8 or9 until you reach the desired level (¶'& to!'&ýZ8).

14.Press ENTER.<BýB;L;B appears.

15.Press SETUP to exit.

Changing the Speaker Distance

When you have your home theater arrangement the way you want it (speakers, receiver, and any components), you can change the speaker distance entered in the receiver’s memory. The default settings are 10 ft.

1.Imagine there is a straight line running from the front left speaker to the front right speaker.

2.Measure the distance in a perpendicular line from your listening position (for example, your couch) to the imaginary line.

Note: Do not meaure the distance to the speakers, just the line.

3.Repeat Steps 1–2for the rear (surround) speakers.

4.Measure the distance in a perpendicular line from your listening position (for example, your couch) to the center speaker.

5.Press SETUP, then press8twice.IFý:?IJ appears.

6.Press 7.<HEDJ appears.

7.Press 7again.<ý'&<J appears. To change the distance between

the listening position and the front speakers, repeatedly press 8or9until you reach the desired level (to)&ý<J).

8.Press ENTER.9;DJ;H appears.

9.Press 7.9ý'&<J appears. To change the distance between the

listening position and the center speaker, repeatedly press 8or

9until you reach the desired level (to)&ý<J).

10.Press ENTER.IKHH$ appears.

Remote Control Operation

13

TUNING MODE
FM MODE

11.Press 7.Iý'&<J appears. To change the distance between the

listening position and the rear (surround) speakers, repeatedly press 8or9until you reach the desired level (to)&ý<J).

12.Press ENTER.<HEDJ appears.

13.Press SETUP to exit.

Surround Effects

Important: The center and rear speakers only operate when the unit is set to a surround sound mode and the source material being played is recorded or broadcast in Dolby Digital, DTS or Dolby Pro Logic surround sound.

Stereo broadcasts or recordings will produce some rear channel effects when played in a surround mode. However, mono sources will not produce any sound from the rear speakers.

Changing System Settings - Special Circumstances

When you make a copy of DVD/CD via TAPE output, set the front speaker size to <#B7H=;. Set the surround mode toIJ;H;E.

USING THE REMOTE CONTROL UNIT TO CONTROL ADDITIONAL COMPONENTS

You can set your remote control to control other components such as a VCR, TV, satellite receiver or cable box.

1.Turn on the component to be programmed.

2.Look up the brand and corresponding code(s) in the code list (see “Manuracturer’s Codes” on Page 23).

3.While holding down the appropriate source button (VCR,TV, orSAT) on the remote control, use the number keys enter the first code from the code list.

4.Release the component button, then press POWER.

If you have entered the correct code, the component turns off.

If the component does not turn off, repeat Steps 3 and 4 and subustitute use the next code (if available) listed for the brand of your component until the component responds to the remote command.

Note: To turn on or off the receiver when you select the VCR, SAT, or TV function, pressPOWER twice.

Cautions:

This remote control unit may not operate on all models of the brands shown.

If batteries are removed from the battery compartment of the remote unit, replace the batteries within 30 minutes or the codes are lost. You must then re-enterall previously programmed codes.

The buttons on the remote control unit may not work correspondingly with those on the components brands.

Experiment with the remote control and your components to see which buttons work. If only a few functions operate, repeat Step 4 to see if another code operates more buttons.

CONTROLLING THE TUNER

1.Press POWER. The last selected function appears.

2.Press TUNER.

3.Press BAND to select the desired band.

4.Repeatedly press TUNING/PRESET ) or- to tune in the desired station.

To change the frequency by one step, press TUNING/PRESET ) or - quickly (less than half a second).

To tune to the next clear frequency, hold downTUNING/PRESET )or-,then release the button. The system automatically tunes to the next strong station.

Listening To FM Stereo Broadcasts

In FM mode, press to select stereo or mono. When you select the stereo mode, IJ appears to the right ofJkd[Z. It goes off when you select mono.

When you listen to very weak FM stereo stations, you might hear higher-than-normalbackground hiss. Switch to mono to eliminate the hiss.

Presetting Radio Stations

You can preset 30 AM and 30 FM stations regardless of the reception. Tune in the desired stations using auto or manual tuning.

Manual Preset

1.Press BAND to select the desired band.

2.Repeatedly press TUNING/PRESET ) or- to tune in the desired station.

To change the frequency by one step, press TUNING/PRESET ) or - quickly (less than half a second).

To tune to the next clear frequency, hold down TUNING/PRESET

) or-,then release the button. The system automatically tunes to the next strong station.

3.Press MEMORY.C;CE flashes for 5 seconds. WhenC;CE goes off, press the button again (C;CE flashes again).

4.Select the preset number with TUNING/PRESET )or-.

5.Press MEMORY again.

6.Repeat Steps 1–5to memorize other stations (up to 30 stations for each band). If you store a new station on a memory number in which a station is stored, the old station is cleared.

To store stations on the other band, repeat Steps 1–6,substituting the other band in Step 1.

Note: If you want to store more stations later, you might find that pressingTUNING/PRESET ) or- only moves the tuner to the next preset station (instead of moving the frequency one step). If this happens, press to return to manual tuning (see “Switching Between Preset Stations and Manual Tuning”).

14

Remote Control Operation

FM MODE/

Auto Preset

1.Press BAND to select the desired band.

2.Hold down MEMORY for about 3 seconds.

3.The tuner automatically begins scanning, and stores the first 30 strong signals it receives.

4.Scanning stops automatically after radio stations have been stored in the auto preset memory.

Note: PressMEMO again to stop auto scanning earlier.

To store stations on the other band, repeat Steps 1–4,substituting the other band in Step 1.

Listening to Preset Stations

To listen to a radio station stored in the station memory, press TUNING MODEthen TUNING/PRESET)or -.

Switching Between Preset Stations and Manual

Tuning

If you store preset stations, pressing TUNING/PRESET ) or- scrolls through the preset stations, rather than changing the frequency station by station.

To switch to scrolling by individual stations, press TUNING MODE, then repeatedly press TUNING/PRESET ) or - quickly to change the frequency by one step. Or hold down TUNING/PRESET : or ; to tune to the next clear station.

To switch back to scrolling through the preset stations, press TUNING MODE, then repeatedly press TUNING/PRESET ) or - until you reach the desired station.

CONTROLLING THE CD PLAYER

You can use the receiver’s 3-DVDchanger to listen to audio CDs.

Important: You can only use audio CDs and someCD-Rswith the reciever.CD-ROM,CD-G,photo CD, andCD-idiscs can not be played on this player.

1.Press POWER.

2.Press DVD.

3.On the receiver, press DISC 1,DISC 2, orDISC 3 to open the desired drawer.

4.Place the desired CDs in the tray, then press the appropriate DISC button again to close the drawer.

Note: If you want to load more than one CD, you can press another DISC button. The receiver closes the open drawer and opens the drawer of the DISC button you pressed.

5.To select a CD, repeatedly press DISC SKIP until the desired CD’s number blinks.

6.To play, press BAND/7.

To pause playback, press (pause icon). To resume playback, press(pause icon) again or pressBAND/7.

To move forward through a track, hold down TUNING/PRESET - for about 2 seconds. Repeat up to two times to increase the fastforward speed. To resume playback, press BAND/7.

To move backward through a track, hold down TUNING/PRESET

) for about 2 seconds. Repeat up to two times to increase the rewind speed. To resume playback, pressBAND/7.

Note: At the beginning or end of a track on an audio CD, the scan speed returns to normal.

To skip to the next track on the CD, press TUNING/PRESET - once.

To return to the beginning of the current track, press TUNING/ PRESET).

To return to the previous track, press TUNING/PRESET )twice.

To stop playback, pressFM MODE/ '. The disc icon stops rotating, andH;IKC; appears. To resume playback, pressBAND/7. To stop playback completely, press ' again.

Changing the Sound Mode

For a surround mode, repeatedly pressSURROUND until the desired mode (J>;7J;H,>7BB,IJ7:?KC,IJ;H;E, orFHEýBE=?9) appears.

Note: Dolby Digital and DTS modes do not work with CDs.

Using GUI Menu Icons

GUI menu icons show the current track number and elapsed time of a CD. Some icons only show the indicated information. Other icons allow the settings to be changed.

Important: You must turn on your television to view the GUI menu icons.

Follow these steps to view or change GUI information.

1.Press GUI during playback. Icons of the current track number and the elapsed time appear.

2.Press the remote’s 6or7to select the desired item. The currently selected item is highlighted.

The first icon is the track icon. If you select it, you can jump to the

desired track number by pressing the number keys and ENTER, or by pressing ) or-.

The second icon is the time icon. It shows the elapsed time. You cannot change it. It is only for viewing.

Repeat Play

Press REPEAT during playback. Each time you press this button, the TV screen displays the repeat mode setting and the disc will repeat a track.

The repeat mode changes between H;F;7JýED;,H;F;7Jý7BB,H;F;7J 7BBý:?I9I, andH;F;7JýE<< as you press the button.

To return to normal play, press REPEAT several times untilH;F;7JýE<< appears.

Note: Repeat play works only with discs for which the elapsed playing time appears in the display window during playback.

Remote Control Operation

15

Programming Tracks

This function allows you to program up to 32 tracks for playback in any desired order. This function only operates with audio CDs (not DVDs).

Note: The disc must be recognized by the receiver, so play the disc for a little while after loading, then program it.

1.Press FM MODE/ ' to stop the CD.

2.Press PROGRAM.&'ý¶ý¶ appears.

3.Repeatedly press DISC SKIP to select the desired CD (if necessary). The CD number appears to the far right of the display.

4.Press the appropriate numeric buttons, then press ENTER to program the first desired track.

5.Repeat Steps 2–4to program more tracks.

To check the programmed order, press STOP twice. Repeatedly press 8or 9to view the programmed order.

To clear the programming, pressSTOP twice, then pressCLEAR.

Notes:

If you try to select more than 32 tracks, FULL appears and you cannot program any more tracks.

If you press PROGRAM twice successively while programming, the programming stops andF#E<< appears.

Press BAND/7to start program playback.

Modifying the Program and Adding a Track

1.Press STOP twice. You cannot modify the programming in Resume Mode.

2.Repeatedly press 8 or9 to select the desired programmed track.

To clear the track, press CLEAR.

To change the track to another track, press the numeric buttons, then ENTER.

To change the track to a track on another disc, press DISC SKIP, the numeric buttons, then ENTER.

To add a track, repeatedly press8 or9 until you reach the last programmed track. Press8 or9 again. Enter the appropriate numeric buttons, then pressENTER to program the desired track.

3.To start program playback again, press PROGRAM, thenBAND/

7.

Note: The programmed contents are lost if you turn off the unit or change the function.

Random Play

Press RANDOM. The unit randomly selects trucks.

Note: PressingRANDOM also clears any programming.

CONTROLLING THE SLEEP TIMER

You can set the sleep timer to turn off the receiver after a set period of time.

Repeatedly press SLEEP to set the sleep timer to the desired time ('&,(&,)&,*&,+&,,&,-&,.&,or/& minutes). The receiver turns off when the selected time has expired.

16

Remote Control Operation

SLOW +
MEMO-

ˆ DVD Player Operation

BASIC PLAYBACK

1.Press POWER. The last selected function appears.

2.If necessary, press the remote’s DVD or rotate the receiver’sFUNCTION until DVD appears.

3.Press DISC 1,DISC 2, orDISC 3 to open the desired disc tray.EF;D appears and the corresponding disc indicator (1, 2, or 3) flashes.

Note: The disc indicator 1, 2, or 3 lights even the disc is not in

the tray until the unit check the tray after the receiver’s PLAY or the remote’sBAND/7is pressed.

4.Place a disc on the disc tray with the playback side down. Place the disc in the correct guide on the disc tray. If the disc is out of the guide, it may damage the disc and cause the DVD player to malfunction.

Notes:

If you leave the disc tray open for more than 8 minutes, the disc tray automatically closes.

If you leave the disc tray open, the disc tray automatically closes when the function mode is changed.

5.Press the receiver’s PLAY or the remote’sBAND/7.FB7O appears. The disc tray automatically closes and the receiver loads the disc. After loading the disc, the receiver enters menu mode.

Note: If you close the tray by pressingDISC 1,DISC 2, orDISC 3, the receiver does not load the disc. PressPLAY to load the disc.

6.To select another disc, repeatedly press DISC SKIP on the remote or the receiver until the desired disc loads.

Note: After playing back all of the chapters in the title, the DVD player automatically stops and returns to the menu screen.

7.When the menu screen appears on your television screen, press the remote’s 6,7,8, or9 to select the Play Movie option, then press the remote’sBAND/7 or the receiver’sPLAY. The receiver begins playback.

Cautions:

Do not move the DVD player during playback. Doing so may damage the disc and the unit.

Use DISC 1,DISC 2, orDISC 3 on the main unit to open or close the disc trays. Do not push the disc tray while it is moving. Doing so may cause the DVD player to malfunction.

Do not push on the disc tray or put any objects other than discs on the disc tray. Doing so may cause the DVD player to malfunction.

Keep your fingers well clear of the disc tray as it is closing. Keep children’s fingers away from the closing disc tray as there is a risk of personal injury.

When the inhibit icon appears on the TV screen while a button is pressed, it means that the function is not available on the disc you are playing.

.Depending on the DVD disc, some operations may be different or restricted. Refer to the jacket or case of the disc you are playing.

Stopping Play

Press the receiver’s STOP or the remote’sFM MODE/'. When play is

stopped, the receiver remains at the point where the receiver’s STOP or the remote’sFM MODE/' was pressed, andH;IKC; appears.

Press the receiver’s STOP or the remote’sFM MODE/' again to stop. The resume option is cleared when the receiver’sSTOP or the remote’sFM MODE/' is pressed the second time.Note: The resume option is also cleared when the power is turned off and then on.

Press the receiver’s PLAY or the remote’sBAND/7 to resume the playback from this point.

Notes:

The resume option works only with discs for which the elapsed playing time appears on the window display during playback.

Opening the disc tray cancels the resume option.

The resume option may not be available on some DVD discs.

Pausing Play

Press the receiver’s f or the remote’sMEMORY/ f.

To resume normal playback, press the receiver’s PLAY or the remote’sBAND/7.

Advancing by Frames

Press the receiver’s f or the remote’sMEMORY/ f while the DVD is paused. Each time you press the receiver’sf or the remote’s

RY/ f, the picture advances one frame.

To resume normal playback, press the receiver’s PLAY or the remote’sBAND/7.

Playing in Slow-Motion

Press the remote’s SLOW – /+ during playback. During slow playback, the playback speed and direction can be selected withSLOW – /+ .

To decrease the playback speed, repeatedly press SLOW .

To reverse the playback direction, press to the playback direction. As you press the button the playback speed changes 1/2, 1/ 4, 1/8.

To return to normal playback, press the receiver’s PLAY or the remote’sBAND/7.

DVD Player Operation

17

Skipping Chapters

To skip forward, press TUNING/PRESET -.The receiver skips forward one chapter each time the button is pressed.

To skip backward, press TUNING/PRESET ). If you pressTUNING/ PRESET ) once midway through a chapter, the receiver returns to the beginning of that chapter. The receiver then skips backward one chapter each subsequent time you pressTUNING/PRESET ).

Scanning

To scan forward through a DVD, hold down the remote’s TUNING/ PRESET or the receiver’s TUNING/PRESET ,-ýfor more than 1 second. Repeat up to three times to increase the fast-forward speed (2X, 4X, 16X, or 100X). To resume playback, press the receiver’s PLAY or the remote’s BAND/7.

To scan backward through a DVD, hold down the remote’s TUNING/ PRESET ) or the receiver’s TUNING/PRESET )ý# for more than 1 second. Repeat up to three times to increase the fast-reverse speed (2X, 4X, 16X, or 100X). To resume playback, press the receiver’s PLAY or the remote’s BAND/7.

Notes:

The DVD player does not play back sound during slow-motion,high-speed-reverse,orhigh-speed-forwardplayback of DVDs.

Subtitles do not appear on the screen during slow motion or scan playback.

The DVD player provides four scan speeds in each direction for DVD movie play.

The DVD player does not play back in slow-motionin case of audio CD.

In some equipment connected to digital output for DTS sound, a noise can be heard during fast-forwardorfast-reverseplayback of DTS DVDs.

ADVANCED FEATURES

Note: For the advanced features, the receiver’s display screen does not change. The displays appear on your television screen.

Using GUI Menu Icons

GUI menu icons show disc information (for example, title or chapter number, elapsed playing time, audio/subtitle language, angle) and player information (for example, repeat play, play mode).

Some icons only show the indicated information. Other icons allow the settings to be changed.

Follow these steps to view or change GUI information.

1.Press GUI during playback.

Note: Title function can also be accessed from the stop mode.

Icons of the current title number, current chapter number, elapsed time, the current audio soundtrack language, current subtitle language, and current angle number appear.

Below each icon is the current information for that menu (for example, ( appears under the chapter icon when you are watching the movie’s second chapter).

Note: Some DVDs might not provide all of the above GUI menu icons.

2.Press the remote’s 6or7to select the desired item. The currently selected item is highlighted.

The first icon is the title icon. When you select it , you can jump to the desired title number by pressing the remote’s number keys, thenENTER.

The second icon is the chapter icon. When you select it, you can

jump to the desired chapter number by pressing the remote’s number keys, then ENTER, or by pressing6or7.

The third icon is the time icon. When you select it, you can move to a desired time in the movie by pressing the number keys, then

ENTER.

The fourth icon is the audio icon. When you select it, you can change the soundtrack language by repeatedly pressing AUDIO until the desired language appears. To select the current setting, press ENTER.

The fifth icon is the subtitle icon. When you select it, you can change the subtitle language by repeatedly pressing SUB TITLE until the desired language appears. To select the current setting, press ENTER.

The last icon is the angle icon. When you select it, you can change the angle by repeatedly pressingANGLE until the desired number appears. To select the current setting, pressENTER.

Using a Title Menu

Some DVDs may contain two or more titles. If the disc has a title menu recorded on it, you can use TITLE to select the movie title.

Notes:

The details of operation differ depending on the DVD.

Selecting a title may not be possible on certain DVD discs. Follow these steps to select a movie title.

1. Press TITLE. A list of the DVD’s titles appears.

2.Press BAND/7 orENTER to resume play from the scene whenTITLE was first pressed.

3.Press the remote’s 8,9,6, or7, thenENTER orBAND/7. Or press the numeric button(s), to select the desired title. The selected title now starts playing.

Using a DVD Menu

Some DVDs have unique menus called DVD menus. For example, DVDs programmed with complex contents provide guide menus, and those recorded with various languages provide menus for audio and subtitle language.

The DVD menu’s contents and operation differ from disc to disc. The following procedure explains the basic operation when this feature is used.

18

DVD Player Operation

SUB TITLE

Press MENU during play. The DVD menu available on the disc now appears. PressingRETURN resumes play from the scene whenMENU was first pressed.

Note: The resume play option might not be possible on certain discs.

Press the remote’s 8,9,6, or7, thenENTER. Or press the numeric button(s) to select the desired item. The selected item is now executed.

Changing Subtitle Language

Note: This operation works only with DVDs on which multiple subtitle languages are recorded.

Press during playback. When no subtitles are recorded, E<< appears instead of the language number. Repeatedly pressSUB TITLE until the desired language is selected.

To eliminate subtitles, repeatedly press SUB TITLE and selectE<<.

Notes:

When the desired language is not selected even after pressing the button several times, it means that the language is not available on the disc.

When the power is turned off or the DVD player is stopped, the subtitle language selected at the initial settings appears.

The repeat mode changes between 9>7FJ;Hý H;F;7J,J?JB;ý H;F;7J, andH;F;7JýE<< as you press the button.

To return to normal play, press REPEAT several times until OFF appears.

Notes:

.Repeat Play works only with discs for which the elapsed playing time appears in the DVD display window during playback.

Repeat Play may not work correctly with some DVDs.

Zooming In

The Zoom feature allows you to zoom in and enlarge the picture on the screen to either 4 times (X4) or 16 times (X16) its normal size.

Press ZOOM during normal playback or still playback.

To resume normal size, press ZOOM to cancel the zoom feature and resume normal playback or still playback.

Notes:

Some DVDs may not respond to the zoom feature.

The zoom feature does not work on subtitles or menus included on DVD video discs.

Changing Soundtrack Language

Note: This operation works only with DVDs on which multiple soundtrack languages are recorded.

Press AUDIO during play. The currently selected soundtrack language appears. Repeatedly pressAUDIO until the desired language is selected.

Notes:

When the desired language is not selected even after pressing the button several times, it means that the language is not available on the disc.

When the power is turned off or the DVD player is stopped, the language heard is the one selected at the initial settings.

Viewing from Another Angle

Some DVDs may contain scenes which have been shot simultaneously from a number of different angles. For these discs, the same scene can be viewed from each of these different angles using ANGLE. The recorded angles differ depending on the disc.

Press ANGLE during playback. The currently selected angle appears. Repeatedly pressANGLE until the desired angle is selected.

Note: This function only works for discs having scenes recorded at different angles.

Using Repeat Play

Press REPEAT during playback. Each time you press this button, the TV screen displays the repeat mode setting and the disc will repeat a chapter or title.

SETTING RATING LEVEL AND PASSWORD

This is to prohibit the playing of specified DVDs which are unsuitable for children. Some DVD discs contain a restriction level which enables parents to remove scenes or prevent playback of discs by children. The DVD player is equipped with a password device designed to prevent children from changing the level.

Selecting a Rating Level

1.Press DVD SET UP.

2.At the setup screen, press 8or9to selectH7J?D=, then press

ENTER.

Note: The password is set to 1,2,3,4 as a default. The rating is set to unlock as a default.

3.Enter a password and press ENTER.

4.Repeatedly press ENTER to select the desired level.

You cannot play DVD video discs rated higher than the level you selected unless you cancel the parental lock function. For example, when you select level 7, discs rated higher than level 7 are blocked and cannot be played.

The parent lock level is equivalent to the following USA movie ratings.

Level

Movie Rating

 

 

 

 

7

NC-17

 

 

6

R

 

 

4

PG-13

 

 

3

PG

 

 

1

G

 

 

DVD Player Operation

19

5. Press DVD SET UP to exit.

Notes:

Some titles do not match with the rating level described as above.

If you change the level and enter a password, playback of all DVDs with ratings higher than your selection will be blocked, unless you enter the correct password again. For example: if you change the level to 5, the DVD player will not play discs with ratings of 6, 7, or 8 unless the correct password is entered from the remote control.

Setting a Password

If you change the rating level to 7 or lower, you must enter a 4-digitpassword to access playback of discs with higher ratings.

To set this password, follow these steps.

1.Press DVD SET UP.

2.At the setup screen, press 9 to selectF7IIMEH:, then press

ENTER.

3.Type a 4-digitpassword intoEB:. (For example, 1234).

Important: Do not forget your password.

4.Type same the 4-digitpassword intoD;M, then pressENTER.

Clearing Your Password

If you forget your password, you can clear the current password.

At the SETUP screen, press 9 to select F7IIMEH:, then press ENTER.

Enter 4-digitnumber (for example, 2850), then pressENTER. The 4- digit password is cleared.

SELECTING TV ASPECT

Select the appropriate screen type according to your TV set. Conventional size screens use a 4:3 aspect ratio, and wide-screensuse a 16:9 ratio.

1.Press DVD SET UP.

2.At the setup screen, press 8 or9 to selectJLý:?IFB7O, then pressENTER.

3.Repeatedly press ENTER to select the desired aspect, then pressDVD SET UP. You must select the type of TV picture (aspect ratio) that corresponds to the type of TV you are connecting to the DVD unit.

*0)ýFI (Pan & Scan) — If you have a conventional TV set and your DVD is not formatted for widescreen viewing, use this setting.

*0)ýB8 (Letterbox)If you have a conventional TV set and your DVD is formatted for widescreen viewing, use this setting. All video material not formatted in the Pan & Scan style is played back in the letterbox style. Black bands appear at top and bottom of screen.

',0/ýM?:; (Widescreen) — If you have awide-screenTV set, use this setting. The DVD plays in full size. (You must also set your widescreen TV to “full size”).

SELECTING DIGITAL AUDIO OUT

Each DVD has a variety of audio output options. If you connected a device to the receiver’s digital optical jacks (see “Connecting a Digital Optical Audio Devices” on Page 7), you might have to change the digital audio output setting. Set the player’s Digital Audio Output according to the type of audio system you use.

1.Press DVD SET UP.

2.At the setup screen, press 8or9to select:?=?J7BýEKJ.

3.Repeatedly press ENTER to select the desired output (F9C or8?JIJH;7C) , then pressENTER.

8?JIJH;7C — Select8?JIJH;7C if you have an amplifier or other equipment with DTS decoder or Dolby Digital decoder connected to the receiver.

F9C — SelectF9C if you have an amplifier or other equipment with linear PCM only (or a MD recorder or a DAT deck) connected to the receiver.

Caution: If an active digital audio output signal is supplied to an receiver or other equipment without a corresponding digital decoding capability, a very loud noise may be produced which could permanently damage the speakers.

Note: When you make a digital recording from CD to your house audio CD recorder entire CD tracks are recorded as 1 track. This is because there is no track information.

20

DVD Player Operation