Quantum 06 edge va User Manual

Size:
7.92 Mb
Download

QUANTUM

Q6 Edge VA

S A F E T Y G U I D E L I N E S

WARNING! A Quantum Rehab Provider or a qualified technician must perform the initial setup of this power chair and must perform all of the procedures in this manual.

The symbols below are used throughout this owner’s manual and on the power chair to identify warnings and important information. It is very important for you to read them and understand them completely.

WARNING! Indicates a potentially hazardous condition/situation. Failure to follow designated procedures can cause either personal injury, component damage, or malfunction. On the product, this icon is represented as a black symbol on a yellow triangle with a black border.

MANDATORY! These actions should be performed as specified. Failure to perform mandatory actions can cause personal injury and/or equipment damage. On the product, this icon is represented as a white symbol on a blue dot with a white border.

PROHIBITED! These actions are prohibited. These actions should not be performed at any time or in any circumstances. Performing a prohibited action can cause personal injury and/or equipment damage. On the product, this icon is represented as a black symbol with a red circle and red slash.

INTENDEDUSE

The intended use of the Pride Mobility Products device is to provide mobility to persons limited to a seated position that have the capability of operating a powered wheelchair.

Quick Reference Information

Quantum Rehab Provider:

Address:

Phone Number:

Purchase Date:

NOTE: This owner’s manual is compiled from the latest specifications and product information available at the time of publication. We reserve the right to make changes as they become necessary. Any changes to our products may cause slight variations between the illustrations and explanations in this manual and the product you have purchased. The latest/current version of this manual is available on our website.

NOTE: This product is compliant with WEEE, RoHS, and REACH directives and requirements.

NOTE: This product meets IPX4 classification (IEC 60529).

NOTE: The Q6 Edge VA and its components are not made with natural rubber latex. Consult with the manufacturer regarding any after-marketaccessories.

Copyright © 2013

Pride Mobility Products Corp.

INFMANU4409/Rev B/September 2013

 

C O N T E N T S

 

I.

INTRODUCTION ...................................................................................................................................

4

II.

SAFETY .....................................................................................................................................................

5

III.

YOUR POWER CHAIR ........................................................................................................................

7

IV.

ASSEMBLY ............................................................................................................................................

12

V.

COMFORT ADJUSTMENTS ...........................................................................................................

16

VI. BATTERIES AND CHARGING ......................................................................................................

23

VII. CARE AND MAINTENANCE ..........................................................................................................

27

Q6 Edge VA

www.pridemobility.com

3

I . I N T R O D U C T I O N

SAFETY

WELCOME to Quantum Rehab, a division of Pride Mobility Products (Pride). The power chair you have purchased combines state-of-the-artcomponents withsafety, comfort, and styling in mind. We are confident that these design features will provide you with the conveniences you expect during your daily activities. Once you understand how tosafely operate and care for your power chair, it should give you years of trouble free operation and service.

Read andfollow all instructions, warnings, and notes in this manual before attempting to operate your power chair for the first time. You must also read all instructions, warnings, and notes contained in any supplemental instructional booklets for the controller, front riggings, and/or seating system that accompanied your power chair before initial operation. Yoursafety depends upon you, as well as your provider, caretaker, or healthcare professional in using good judgement.

If there is any information in this manual which you do not understand, or if you require additional assistance for setup or operation, please contact your Quantum Rehab Provider. Failure to follow the instructions in this manual and those located on your power chair can lead to personal injury and/or damage to the power chair, including voiding the warranty.

PURCHASER’S AGREEMENT

By accepting delivery of this product, you promise that you will not change, alter, or modify this product or remove or render inoperable or unsafe any guards, shields, or other safety features of this product; fail, refuse, or neglect to install any retrofit kits from time to time provided by Pride to enhance or preserve the safe use of this product.

SHIPPING AND DELIVERY

Before using your power chair, make sure your delivery is complete as some components may be individually packaged. If you do not receive a complete delivery, please contact your Quantum Rehab Provider immediately. Where damage has occurred during transport, either to the packaging or content, please contact the delivery company responsible.

Pride Mobility Products Corporation Attn.: Customer Care Department 182 Susquehanna Avenue

Exeter, PA 18643-2694info@pridemobility.com

NOTE: If you ever lose or misplace your copy of this manual, contact us and we will be glad to send you a new one immediately.

4

www.pridemobility.com

Q6 Edge VA

I I . S A F E T Y

PRODUCT SAFETY SYMBOLS

The symbols below are used on the power chair to identify warnings, mandatory actions, and prohibited actions. It is very important for you to read and understand them completely.

NOTE: There are more warnings identified and explained in the Consumer Safety Guide that is included with your power chair. Please become familiar with all the warnings and safety information found in the Consumer Safety Guide and refer to this resource often.

Read and follow the information in the owner’s manual.

Locked and in drive mode.

Place unit on level ground and stand to one side when changing from drive mode to freewheel mode or freewheel mode to drive mode.

Unlocked and in freewheel mode.

Indicates power chair securement points.

Indicates that power chair, with similarly labeled seating system, conforms to ANSI/ RESNA WC/Vol. 4, Section 19 for transport of an occupied power chair in a motor vehicle.

Indicates that power chair with a similar label is not rated for occupied transit.

Class II Equipment

Manufactured in

MAIN FRAME

Power chair information label.

Q6 Edge VA

www.pridemobility.com

5

I I . S A F E T Y

GENERAL GUIDELINES

MANDATORY! Do not operate your new power chair for the first time without completely reading and understanding this owner’s manual.

Your power chair is a state-of-the-artlife-enhancementdevice designed to increase mobility. Pride provides an extensive variety of products to best fit the individual needs of the power chair user. Please be aware that the final selection and purchasing decision regarding the type of power chair to be used is the responsibility of the power chair user, who is capable of making such a decision, and his/her healthcare professional (i.e., medical doctor, physical therapist, etc.).

The contents of this manual are based on the expectation that a mobility device expert has properly fitted the power chair to the user and has assisted the prescribing healthcare professional and/or the Quantum Rehab Provider in the instruction process for the use of the product.

There are certain situations, including some medical conditions, where the power chair user will need to practice operating the power chair in the presence of a trained attendant. A trained attendant can be defined as a family member or care professional specially trained in assisting a power chair user in various daily living activities.

As you begin using your power chair during daily activities, you will probably encounter situations in which you will need some practice. Simply take your time and you will soon be in full and confident control as you maneuver through doorways, on and off of elevators, up and down ramps, and over moderate terrain.

Below are some precautions, tips, and other safety considerations that will help you become accustomed to operating your power chair safely.

Pre-RideSafety Check

Get to know the feel of your power chair and its capabilities. Pride recommends that you perform a safety check before each use to make sure your power chair operates smoothly and safely.

Perform the following inspections prior to using your power chair:

Check for proper tire inflation. Maintain but do not exceed the psi/bar/kPa air pressure rating indicated on each tire if equipped with pneumatic tires.

Check all electrical connections. Make sure they are tight and not corroded.

Check all controller connections to the power base. Make sure they are secured properly.

Check the brakes. See VII. “Care and Maintenance.”

Check battery charge. See VI. “Batteries and Charging.”

Ensure the manual freewheel levers are in drive mode before sitting on the power chair.

NOTE: If you discover a problem, contact your Quantum Rehab Provider for assistance.

6

www.pridemobility.com

Q6 Edge VA

I I I . Y O U R P O W E R C H A I R

THE Q6 EDGE VA POWER CHAIR

Your power chair has two main assemblies: the seat assembly and the power base assembly. See figure 1. Typically, the seat assembly includes the armrests, seatback, and seat base. The power base assembly includes two motor/brake assemblies, two drive wheels, four caster wheels, two batteries, and wiring harnesses.See figures 1, 2, and 3.

 

 

SEATBACK

SEAT ASSEMBLY

 

 

 

 

ARMREST

ARMREST

 

 

 

 

JOYSTICK

 

 

CONTROLLER

 

 

SEAT BASE

POWER BASE

 

 

ASSEMBLY

 

 

CASTER WHEEL

 

 

MANUAL FREEWHEEL

 

 

LEVER

 

 

 

 

FRONT RIGGING

DRIVE WHEEL

SPRING SHOCK/GAS

(FOOT PLATFORM SHOWN)

 

 

DAMPER LOCATION

 

 

CASTER WHEEL

 

Figure 1. The Q6 Edge VA Power Chair (Synergy Seat Shown)

Q6 Edge VA

www.pridemobility.com

7

I I I . Y O U R P O W E R C H A I R

REAR SHROUD TRAPEZE BARS

FRONT COVER

MANUAL FREEWHEEL LEVER

SUSPENSION SPRING

Figure 2. The Q6 Edge VA Power Base

PROHIBITED! The spring tension on your power chair was factory set to meet the needs of the demographic majority of users. Do not adjust the tension of any spring on your power chair.

Electrical Components

The electrical components consist of the controller assembly, the batteries, and the motors. The batteries, motors, and controller power module (if equipped) are located on the power base assembly. The controller is located on the seat assembly. Connectivity between the controller and the motors, batteries, and the battery charger is provided by one or more wiring harnesses. See figure 3.

Controller Harness Connector: The controller harness connector is where the controller plugs into the power base. Each controller uses a different type of harness. Regardless of which type of controller is used, the harness must be secured to the seat assembly and not allowed to drag on the floor.

Motor Connectors: This is where the controller connects to the motors.

Battery Connector: This is where the controller connects to the batteries.

Controller Power Module: This enables the controller to communicate with the batteries and the motors.

8

www.pridemobility.com

Q6 Edge VA

I I I . Y O U R P O W E R C H A I R

Main Circuit Breaker (located on the rear main frame): The main circuit breaker is a safety feature built into your power chair. When the batteries and the motors are heavily strained (e.g., from excessive loads), the main circuit breaker trips to prevent damage to the motors and the electronics. If the circuit trips, allow your power chair to “rest” for approximately one minute. Next, push in the circuit breaker button, turn on the controller, and continue normal operation. If the main circuit breaker continues to trip repeatedly, contact your Quantum Rehab Provider.

CONTROLLER POWER MODULE

 

CONTROLLER CONNECTOR

 

TO BATTERY

 

CONNECTORS

 

TO MOTOR

MAIN CIRCUIT

CONNECTOR

BREAKER

 

TO MOTOR

 

CONNECTOR

 

 

QUICK RELEASE

 

BATTERY CONNECTORS

Figure 3. Q6 Edge VA Electrical Components

Q6 Edge VA

www.pridemobility.com

9

I I I . Y O U R P O W E R C H A I R

Manual Freewheel Levers

For your convenience, your power chair is equipped with a manual freewheel lever mounted on each motor. The levers allow you to disengage the drive motors and maneuver the chair manually.

WARNING! The power chair could roll unintentionally when the drive motors are disengaged on an incline! Property damage, severe injury or death can occur.

WARNING! This chair IS NOT EQUIPPED with an audible or visible warning system to alert the user when one or both drive motors are disengaged.

WARNING! The power chair can drive in circles when only one drive motor is engaged. DO NOT ATTEMPT TO DRIVE IN THIS CONDITION. Property damage, severe injury or death can occur.

WARNING! Ensure both drive motors are engaged before turning on power to the controller or attempting to drive the power chair.

WARNING! Do not attempt to use the power chair or occupy the chair when the drive motors are disengaged.

To operate the manual freewheel levers:

1.Push down both manual freewheel levers for freewheel mode (drive motor disengaged). See figures 4A and 4B.

2.Pull up both manual freewheel levers for drive mode (drive motor engaged). See figures 5A and 5B.

NOTE: You must turn off the power before disengaging the drive motors; otherwise, you may get an error code on the controller. To clear this code, turn off the controller and place the power chair in drive mode. Then, turn on the controller. The error message should be cleared. If it is not, contact your Quantum Rehab Provider.

NOTE: The power chair will be significantly easier to push with the power off.

WARNING! Avoid applying excessive force to the manual freewheel levers.

WARNING! Do not use your foot to operate the manual freewheel levers. Do not stand on the manual freewheel levers. Applying excessive force to the manual freewheel levers may result in damage to the freewheel levers, motors, and brakes.

WARNING! Do not use the freewheel lever handles as tie-downpoints to secure this product.

MANUAL FREEWHEEL LEVER

Figure 4A. Freewheel Mode (Left Drive Motor

Disengaged)

MANUAL FREEWHEEL LEVER

Figure 4B. Freewheel Mode (Right Drive Motor

Disengaged)

10

www.pridemobility.com

Q6 Edge VA

I I I . Y O U R P O W E R C H A I R

MANUAL FREEWHEEL LEVER

MANUAL FREEWHEEL LEVER

Figure 5A. Drive Mode (Left Drive Motor Engaged)

Figure 5B. Drive Mode (Right Drive Motor Engaged)

Q6 Edge VA

www.pridemobility.com

11

I V . A S S E M B L Y

INITIAL ASSEMBLY

Your power chair may require some assembly either before initial use or after transportation. It may also require disassembly to make some comfort adjustments. Figure 6 details those parts of the power chair that are designed to be disassembled and assembled by an end user or by a qualified caregiver before using the product or making comfort adjustments.

NOTE: Any nylon insert lock nut removed during the disassembly or adjustment of the power chair must be replaced with a new nut. Nylon insert lock nuts should not be reused as it may cause damage to the nylon insert, resulting in a less secure fit. Replacement nylon insert lock nuts are available at local hardware stores or through your Quantum Rehab Provider.

ARMREST ANGLE

ADJUSTMENT

CONTROLLER POSITION

SEAT HEIGHT/ANGLE ADJUSTMENT

FOOT PLATFORM

ANGLE ADJUSTMENT

FOOT PLATFORM HEIGHT/DEPTH ADJUSTMENT

Figure 6. Q6 Edge VA Assembly View (Synergy Seat Shown)

12

www.pridemobility.com

Q6 Edge VA

I V . A S S E M B L Y

Seat Installation

It may be necessary to install the seat either prior to initial operation or after transporting your power chair.

For unoccupied transit power chairs, contour seats are attached to the power base with the Universal Mounting System (UMS). The UMS consists of universal parts that may be attached to the seat, regardless of seat width or seat depth. The two main components are aluminum extrusions mounted to the seat base. These extrusions attach to a pair of trapeze bars that are mounted to the power base. See figure 7.

For occupied transit power chairs, the seat plate is secured to the four seat mounting brackets on the power base. The seat plate is located on the bottom of the seat. See figure 9.

NOTE: If your power chair is equipped with a Specialty Seat, Synergy Seat, or a TRU-BalancePower Positioning System, refer to the information provided in separate manuals.

WARNING! Do not pick up the seat frame by the armrests. They are free to pivot, and you may lose control of the seat if they do so.

To install the seat (UMS):

1.Tilt the seat back and slide the rear extrusion onto the rear trapeze bar. See figure 7.

2.Lower the front extrusion onto the front trapeze bar until the seat locks into place.

3.Flip the seat latch safety down.

WARNING! Make sure the seat latch safety is flipped down before using your power chair.

4.Install the controller and route the harness to the back of the power base. See figures 8 or 10.

 

SEAT LATCH SAFETY

REAR

FRONT EXTRUSION

EXTRUSION

TRAPEZE BARS

 

Figure 7. Universal Mounting System and Contour Seat—

UMS

Figure 8. Controller Harness Routing on a Synergy Seat

Q6 Edge VA

www.pridemobility.com

13

I V . A S S E M B L Y

MANDATORY! Prevent controller harness damage! Avoid routing the controller harness on the outside of the armrest pad. Route the harness under the armrest or toward the inside of the armrest pad. Use correct tiedown points for controller harness to prevent the harness from getting caught in the drive tires, pinched in the seat frame, or damaged when passing through doorways.

5.Plug the controller connector into the rear of the power base. See figure 3.

6.Secure the controller harness to the armrest receiver with wire ties. See figure 10.

To install the seat (Transit Securement System):

1.Attach the seat plate to the four mounting brackets on the power base and ensure all hardware is properly installed and tightened securely. See figure 9.

2.Install the controller and route the harness to the back of the power. See figure 10.

MANDATORY! Prevent controller harness damage! Avoid routing the controller harness on the outside of the armrest pad. Route the harness under the armrest or toward the inside of the armrest pad. Use correct tiedown points for controller harness to prevent the harness from getting caught in the drive tires, pinched in the seat frame, or damaged when passing through doorways.

HARDWARE

SEAT PLATE

MOUNTING

BRACKETS

HARDWARE

Figure 9. Seat Installation—OccupiedTransit

WIRE TIES

TO POWER BASE

Figure 10. Controller Harness Routing on a Contour Seat

14

www.pridemobility.com

Q6 Edge VA

I V . A S S E M B L Y

Power Elevating Seat Option

Your power chair may be equipped with a power elevating seat option. While the seat itself may be any one of the styles offered for this model, the way the seat base attaches to the power base is different.

To install the power elevating seat:

l.Place the seat plate interface bracket onto the actuator. See figure 11.

2.Insert the supplied hardware into the actuator and tighten the hardware.

3.Place the seating system onto the seat plate and secure.

4.Plug in the power seat toggle switch harness, if equipped.

Transit Securement System (Optional)

If your power chair is equipped with a transit securement system, it is equipped with manufacturerinstalled front and rear securement brackets and positioning belt anchoring brackets. See figure 12. Refer to the supplement provided with your power chair for information on how to use the transit securement system.

SEAT PLATE INTERFACE

BRACKET

ACTUATOR

Figure 11. Power Elevating Seat Actuator

POSITIONING BELT

ANCHORING BRACKET LOCATIONS

(1 OF 2 SHOWN)

SECUREMENT

BRACKETS

(3 OF 4 SHOWN)

Figure 12. Transit System Securement Brackets

(Synergy Seat Shown)

Q6 Edge VA

www.pridemobility.com

15

V . C O M F O R T A D J U S T M E N T S

COMFORT ADJUSTMENTS

After becoming familiar with your power chair’s operation, you may find the need to make some adjustments to increase your comfort, such as seat height and angle, armrest width, armrest angle and height, foot platform height, depth, and angle, and controller position.

NOTE: If your power chair is equipped with a Specialty Seat, Synergy Seat, or TRU-BalancePower Positioning System, refer to the seat adjustment information contained in separate manuals. If your power chair is equipped with a contoured seating system, refer to the following information.

WARNING! The center of gravity of your power chair was factory set to a position that meets the needs of the demographic majority of users. Your Quantum Rehab Provider has evaluated your power chair and made any necessary adjustments to suit your specific requirements. Do not change your seating configuration without first contacting Pride Mobility Products or your Quantum Rehab Provider.

WARNING! Some power chair components are heavy. You may need assistance to lift or carry them. Please refer to the specifications table for specific component weights before you disassemble the power chair.

WARNING! Remove the occupant from the power chair before making any adjustments.

You may need the following to make comfort adjustments:

metric/standard socket set and ratchet

adjustable wrench

metric/standard hex key set

thread lock

Seat Height and Seat Angle Adjustment

If your power chair is not equipped with a transit securement system, you can change the seat height to one of three positions by raising the front and rear trapeze bars. If you raise or lower only one trapeze bar (front or rear), you can also change the seat base angle (dump).

MANDATORY! If your power chair is equipped with a transit securement system and any adjustment to the seat height or seat angle is necessary, contact your Quantum Rehab Provider. These comfort adjustment can only be made by a Quantum Rehab Provider.

To change the seat height:

1.Turn off the power to the controller.

2.Make sure the power chair is in drive mode.

3.Unplug the controller connector(s) from the power base. See figure 3.

4.Flip up the seat latch safety. See figure 7.

5.Squeeze the seat latch and release the seat from the front trapeze bar.

6.Slide the seat forward and remove it from the power base.

TRAPEZE BARS

HARDWARE

SEAT INTERFACE

WELDMENT

HARDWARE

Figure 13. Seat Height/Angle Adjustment—UMS

16

www.pridemobility.com

Q6 Edge VA

V . C O M F O R T A D J U S T M E N T S

7.Remove the hardware that attaches the trapeze bars to the seat interface weldments. See figure 13.

8.Move the trapeze bars up or down to the desired height.

NOTE: Change the seat dump by raising or lowering only one trapeze bar (front or rear).

9.Reinstall the hardware.

10.Reinstall the seat.

11.Reconnect the controller to the power base.

Seat Position

You can move the seat forward or rearward by changing the extrusion mounting position.

To change the position:

1.Turn off the power to the controller.

2.Make sure the power chair is in drive mode.

3.Unplug the controller connector(s) from the power base.

4.Remove the seat from the power base.

5.Remove both extrusions from the bottom of the seat.

6.Reposition the extrusions on a different set of mounting holes. You must move both extrusions the same number of holes either forward or backwards. See figure 14.

7.Fasten the extrusions back onto the bottom of the seat.

8.Reinstall the seat.

9.Reconnect the controller to the power base.

Manual Recline Seatback Adjustment

If your power chair is equipped with a reclining seat, you can adjust the seatback angle with the seatback release lever. The lever is located on the right side of the seat base.

To adjust the recline angle:

1.Pull up on the seatback release lever.

2.Lean forward or backwards to the desired position.

3.Release the lever.

SEAT MOUNTING HOLES

Figure 14. Seat Position Adjustment

Q6 Edge VA

www.pridemobility.com

17

V . C O M F O R T A D J U S T M E N T S

Seatback Angle Adjustment

If your power chair is equipped with an adjustable seatback, you can adjust it to four (4) different angles: 90°, 102°, 105°, or 107°.

To adjust the seatback angle:

1.Remove the adjusting screws from each seat hinge.

See figure 15.

2.Set the seatback at the desired angle.

3.Reinstall the adjusting screws to each seat hinge and tighten.

Armrest Width Adjustment

You can change each armrest’s width independently of the other.

NOTE: Changing the armrest width may increase the overall width of your power chair.

To change the armrest width:

1.Locate the two armrest knobs on each side of the armrest receiver bracket. See figure 15.

2.Loosen the knobs.

3.Slide the armrests in or out to the desired width.

4.Tighten the knobs.

Armrest Angle Adjustment

To change the armrest angle:

1.Lift the armrest straight up so that it is perpendicular to the floor. See figure 15.

2.Loosen the jam nut.

3.Turn the adjusting screw to raise or lower the front of the armrest.

4.Tighten the jam nut to lock the adjusting screw into place.

Armrest Height Adjustment

To change the armrest height:

1.Loosen the two setscrews located on the armrest receiver. See figure 15.

2.Raise or lower the armrest to the desired height.

3.Tighten the setscrews to secure the armrest.

JAM NUT

ARMREST ANGLE

ADJUSTING

SCREW

ARMREST

HEIGHT

ADJUSTING

SETSCREWS

SEATBACK ANGLE

ADJUSTING SCREW

ARMREST KNOB

Figure 15. Seatback/Armrest Adjustment

18

www.pridemobility.com

Q6 Edge VA

V . C O M F O R T A D J U S T M E N T S

Controller Position

You can move the controller in toward or out away from the armrest, or change the position of the controller for either left-handorright-handuse.

WARNING! Do not place the controller harness so that it can be pinched in the seat frame or the power base frame.

To extend the controller:

1.Flip up the armrest so it is perpendicular to the floor.

2.Loosen the setscrew on the controller bracket. See figure 16.

3.Slide the controller into or out of the armrest to the desired position.

4.Tighten the setscrew to secure the controller.

To change the controller position:

1.Turn off the power to the controller.

2.Unplug the controller connector(s) from the power base.

3.Remove any wire ties securing the controller harness to the armrest.

4.Flip up the armrest so it is perpendicular to the floor.

5.Loosen the setscrew on the controller bracket

6.Slide the controller out of the armrest.

7.Loosen the setscrew in the other armrest.

8.Place the controller in the other armrest.

9.Tighten the setscrews in both armrests.

10.Route the controller harness to the back of the power base and plug in the controller.

11.Secure the controller harness to the armrest with wire ties. See figure 10.

NOTE: If your power chair is equipped with a Specialty Seat, Synergy Seat, or TRU-BalancePower Positioning System, refer to the information provided in supplemental manuals provided with your seating system.

CONTROLLER BRACKET

SETSCREW

Figure 16. Underside of Armrest

Q6 Edge VA

www.pridemobility.com

19

V . C O M F O R T A D J U S T M E N T S

Foot Platform Height Adjustment

The foot platform height is easily adjusted to several different heights.

To raise or lower the foot platform:

1.Remove the hardware from the foot platform bracket. See figure 17.

2.Raise or lower the foot platform to the desired height.

3.Reinstall the hardware into the foot platform bracket and tighten.

Foot Platform Depth Adjustment

You can adjust the depth of the foot platform.

To adjust the foot platform depth:

1.Remove the hardware from the foot platform bracket. See figure 17.

2.Move the foot platform in or out to the desired depth.

3.Reinstall the hardware into the foot platform bracket and tighten.

Foot Platform Angle Adjustment

You can adjust the angle of the foot platform.

To adjust the foot platform angle:

1.Flip up the foot platform and locate the screw. See figure 17.

2.Turn the screw to raise or lower the front of the foot platform.

FOOT

PLATFORM

BRACKET

HARDWARE

SCREW

Figure 17. Foot Platform Adjustment

20

www.pridemobility.com

Q6 Edge VA